Page 1
User Manual
User Manual
Barrel Merchandiser Refrigeration
Barrel Freezer Models: 177BMF3, 177BMF3B, 177BMF3W
Barrel Cooler Models: 177BMR2B, 177BMR2CD
Please read the manual thoroughly prior to equipment set-up,
operation and maintenance.
- 1 -
08/2020
Page 2
User Manual
Installation
Important!!! Please Read Before Installation
• After unboxing, the unit must be kept upright for a minimum of 24 hours in its final installation
location before being plugged in. Failure to do so may cause damage to the compressor and will
void the warranty.
• Make sure that the unit reaches the desired temperature before loading the unit with product.
• Make sure that there is proper ventilation around the unit in the area where it will operate.
• Please read through the manual in its entirety.
Cabinet Location Guidelines
• Install the unit on strong and leveled surfaces
- Level the unit by adjusting the screws located on the bottom of the unit.
- Unit may be noisy if surface is uneven.
- Unit may malfunction if surface is uneven.
• Install the unit in an indoor, well-ventilated area
- Unit performs more efficiently in a well-ventilated area.
- For best performance, please maintain clearance of 4” on the back of the unit.
- Outdoor use may cause decreased efficiency and damage to the unit, and will void your warranty.
• Avoid installation in a high humidity and/or dusty area
- Humidity could cause unit to rust and decrease efficiency of the unit.
- Dust collected on condenser coil will cause unit to malfunction.
- Malfunction due to dirty condenser will void warranty.
• Select a location away from heat and moisture-generating equipment
- High ambient temperatures will cause the compressor to overwork, leading to higher energy bills and gradual
breakdown of the unit.
- Malfunction due to high ambient temperature will void warranty.
Electrical
• Please ensure that the required voltage of the compressor is being supplied at all times. Low or
high voltage can detrimentally affect the refrigeration unit.
• All units should be plugged into a grounded and properly-sized electrical outlet with appropriate
overcurrent protection. Please refer to the electrical requirements on the nameplate.
• Please make sure that your unit has its own dedicated outlet.
• Do not use an extension cord.
- 2 -
Page 3
User Manual
icture), adjust the temperature according to the
8. Maintenance
Disconnect the power supply before maintenance for the machine!
1) Keep the door gasket clean, remove it from the door and wash it.
Dry and seal it as before. Putting some talcum powder on the magnetic
surface would prolong its service life.
2) Bulb replacement： remove the lamp shade, take out the bulb
replace with a new bulb, then mount it again.
3) If there is heavy frost on the evaporator after long usage, take out the
stuff inside the case, disconnect the power, the frost will melt
automatically, clean up the water and connect the power again.
4) Use a soft cloth and dip some water or soap (Non-caustic, neutral
detergent is also available) to clean the unit. Dry the unit after cleaning
to avoid rust.
5) Do not use organic liquid, boiled water, washing powder or acid
stuff to clean the unit. Rinsing the case
use hard brush, steel brush to clean the case.
6) If the unit will not be used for a long time, disconnect the power,
clean it by following the above steps, wipe off the water inside the case
with a soft cloth.
9、 Caution
1) The unit is not suitable for storage of blood, pharmaceutical
products and biological products
2) Do not place heavy articles on the top of the unit.
4) After moving the unit, place the unit for 30 minutes before switching it on.
Running: close the door and connect the power, turn on the lamp switch on the
control panel, the lamp is on. Half an hour later, the temperature inside the case
lower apparently, it indicates the unit on be normally used
5) After connecting the power, the unit should be kept empty for one hour.
1) Adjust the storage temperature through the temperature controller located on
the back of the case(see the p
icture), adjust the temperature according to the
ambient temperature and the foodstuff.
2) See the following picture about the knob scale. The temperature adjustable
capacity is from “1”-“5”, adjust the storage temperature by turning the
temperature controller clockwise. The higher of the number shows the lower of
the storage temperature. The knob can turn freely but can't turn clockwise from
“5”to “1”. Factory setting position is on “3”.
8. Maintenance
Disconnect the power supply before maintenance for the machine!
1) Keep the door gasket clean, remove it from the door and wash it.
Dry and seal it as before. Putting some talcum powder on the magnetic
surface would prolong its service life.
2) Bulb replacement： remove the lamp shade, take out the bulb,
replace with a new bulb, then mount it again.
3) If th
ere is heavy frost on the evaporator after long usage, take out the
stuff inside the case, disconnect the power, the frost will melt
automatically, clean up the water and connect the power again.
4) Use a soft cloth and dip some water or soap (Non-caustic, neutral
detergent is also available) to clean the unit. Dry the unit after cleaning
to avoid rust.
5) Do not use organic liquid, boiled water, washing powder or acid
stuff to clean the unit. Rinsing the case by water is not allowed, don't
use hard brush
6) If the unit will not be used for a long time, disconnect the power,
clean it by following the above steps, wipe off the water inside the case
with a soft cloth.
9、 Caution
1) The unit is not suitable for storage of blood, pharmaceutical
products and biological products
Thermostat knob
Using the CNC thermostat to adjust the temperature. Up arrow adjusts the ↑↑
temperature rising inside the cooler. Down arrow adjusts the temperature ↓↓
dropping inside the cooler. Digital display shows current
temperature inside
the cooler! Press shutdown key for 6 seconds to turn off the system.
ding to the
Temperature Control
The recommended temperature setting for the
refrigerator is at position “3”. For colder temperatures,
turn to position “1”. Warmer temperatures can be
reached by turning the knob to position “5”.
Control Panel
For freezers, the controller is pre-programmed for
frozen food storage but can be adjusted using the up
and down arrows.
CAUTION
Setting the temperature control to the coldest setting may cause the evaporator coil to freeze and ice
up. This will eventually result in a warmer cabinet temperature.
Defrost System
If the frost on the interior walls is more than 1/4”, defrosting should be done.
Method of defrosting: 1) Unplug the unit. Remove all contents of the freezer. After the freezer
temperature rises, frost will melt or scale off. 2) To speed up defrosting, place a pan of hot water
into the unit and close the door. After defrosting, drain the water and then use a soft cloth to dry the
interior walls. Plug unit in and resume operation. Wait until unit reaches desired temperature before
returning product to the freezer.
Note: Never use sharp utensils or ice scrapers to scrape off frost.
Regular Maintenance
Care and Cleaning
The freezer should be cleaned periodically; generally clean it every 30-45 days. Unplug before
cleaning, and use a soft cloth with a solution of warm water and mild soap to scrub inside and
Thermostat knob
se t
outside of the cabinet. Do not use acids, chemical thinner, gasoline or benzene for cleaning any part
of the chest freezer. Dry it with a soft cloth. Never use water to rinse the freezer.
- 3 -
Page 4
User Manual
Safety / Warning
Please pay close attention to the safety notices in this section. Disregarding these notices may lead
to serious injury and/or damage to the unit.
Attention
• To minimize shock and fire hazards, be sure not to overload outlet. Please designate one outlet for
your unit.
• Do not use extension cords.
• Do not put your hands under the unit while it is being moved.
• When the unit is not in use for a long period of time, please unplug the unit from the outlet.
• After unplugging the unit, wait at least 10 minutes before plugging it back in. Failure to do so could
cause damage to the compressor.
Unplug Cord
• To minimize shock and fire hazards, please do not plug or unplug the cord with wet hands.
• During maintenance and cleaning, please unplug the unit.
Proper Grounding Required
• To minimize shock and fire hazards, make sure that the unit is properly grounded.
Warning
• Do not attempt to remove or repair any component unless instructed by factory.
• Make sure that the unit is not resting on or against the electrical cord and plug.
• To minimize personal injury, do not hang on the door.
• Do not store any flammable and explosive gas or liquids inside the unit.
• Do not attempt to alter or tamper with the electrical cord.
- 4 -
Page 5
User Manual
Troubleshooting
Compressor Not Running
Fuse blown or circuit breaker tripped Replace fuse or reset circuit breaker
Power cord unplugged Plug in power cord
Thermostat set too warm Set thermostat to a higher setting
Condensing Units Run For Long Periods of Time
Excessive amount of warm product placed in cabinet Allow adequate time for product to cool down
Prolonged door opening or door ajar Ensure door is closed when not in use. Avoid opening
door for long periods of time
Cabinet Temperature is too Warm
Thermostat set too warm Set thermostat to higher setting
Airflow blocked Re-arrange product to allow for proper air flow.
Make sure there is at least four inches of clearance
from evaporator
Excessive amount of warm product placed in cabinet. Allow adequate time for product to cool down.
Fuse blown or circuit breaker tripped Replace fuse or reset circuit breaker
Unit is Noisy
Loud noise is heard Be sure there is enough space between chest freezer
and the wall. Make sure unit is installed on a level
surface
Sounds like water running No attention required. It is the sound of refrigerant
(liquid for cooling the freezer)
Condensation
Condensation is on the exterior walls of the unit Condensation may build up on the cabinet or the door
when humidity is high
- 5 -
Page 6
User Manual
Warranty Information
1 Year Limited Replacement Warranty - Valid Only in the Continental United States
Galaxy Kegerators, Chest Freezers, Refrigerated and Freezer Merchandisers Only
Unless otherwise stated, Galaxy Equipment warrants to the original purchaser of new, qualified Galaxy
Equipment units (and all parts thereof), that such equipment will be free from defects in material and
workmanship for a period of 1 year from the date of delivery.
If a qualified product is found to be defective during this period, Galaxy Equipment will repair the defective
unit, replace any defective parts, or replace the defective unit.
What This Warranty Does Not Cover:
Galaxy Equipment will not warrant coverage for component failure or other damages that arise under the
following conditions:
• Failure to install and/or use the unit within proper operating conditions specified by Galaxy Equipment
• Failure to properly maintain the unit. This includes, but is not limited to, basic preventative maintenance
like cleaning the condenser coil.
• Products sold or used outside of the Continental United States.
• Any damage that occurs as a result of negligence or improper handling.
• Overloading or improper loading of the unit in a manner that prevents proper airflow.
• Void in mobile settings.
Additionally, no claims can be made against this warranty for spoilage of products, loss of sales or profits, or
anyother consequential damages.
Normal wear type parts, such as light bulbs and gaskets, are not included in warranty coverage.
For Warranty Inquiries or Service:
To obtain warranty service, contact the location where you purchased the product:
www.WebstaurantStore.com:
Call 717-392-7472. You must have your order number ready when contacting.
The Restaurant Store:
If you purchased this unit from your local store location, please contact your store directly.
www.TheRestaurantStore.com:
If you purchased this unit online, call 717-392-7261. You must have your order number ready when
contacting.
Failure to contact the designated location prior to obtaining equipment service may void your warranty.
- 6 -
Loading...