Galaxy Aqua 4000, Aqua 4000 si Installation Instructions Manual

IMPORTANT!

This Step-by-Step guide should be given to the customer

after installation and demonstration.

Aqua

44

000000

44

000000

Ii

S

&

Instantaneous Electric Shower

Installation Instructions

Technical Hotline

Telephone: [phone] Fax: [phone]

Email: [e-mail]

9.00 am - 5.00 pm Monday to Friday

SERVICE POLICY

In the event of you needing to contact the Galaxy Technical Hotline, the following
procedure should be followed:-

1

If a service call is booked, you or a representative must be present
during the Engineers visit.

Before telephoning the Galaxy Technical Hotline you should ensure
that you have the model number, power rating, serial number and
date of purchase.

The Galaxy Technical Hotline will be able to inform you whether the
fault can be rectified by the provision of a replacement part or an on
site visit by a Qualified Service Engineer.

If the product is no longer covered by the Guarantee, a charge will
be made for the site visit and for any parts supplied.

A charge will be made where a call under the terms of the guarantee
has been booked and a failure was not product related, or an engineer
arrives and is not able to gain access.

2

3

4

5

01/2011

Aqua

44

000000

6

5

7

4

3

8

9

10

2

1

TEMPERATURE

LOW

COLD

STOP

HIGH

PRESSURE

LOW

AUTO
RESET

6

9

0 m

m

339

mm

218 mm

PACK
CONTENTS

Shower Unit
Showerhead
Flexible Hose
Slider Rail Tube
Slider Rail Brackets
Slider Rail Showerhead Holder
Soap Dish
Screw Pack

IMPORTANT

1. Shower installation must be carried out

by a suitably qualified person and
conform with IEE Regulations and
National Water Council bylaws.

2. This shower unit is designed to be
connected to a 15mm cold water mains
supply.
Do not connect to a tank supply

unless a suitable booster pump is
fitted.

3. To make sure of activating the heating

elements, the shower must be
connected to a mains water supply with
a minimum running pressure of 100kPa
(15 lb/sq in) - (1 Bar) at a minimum flow
rate of 8 litres per minute. The maxi­ mum static pressure must be no greater
than 1000kPa (150 lb/sq in) - (10 Bar).
(Minimum running pressure must be

obtained at 9 litres/minute for 9.5kW
and 11 litres/minute for the 10.5kW).

4. The shower unit must not be fitted
where it may be exposed to frost, for
example in an outdoor shower area.
The shower must not be used if

suspected of being frozen.
Frost damage is not covered by the

guarantee.

5. Plumbers jointing compound must
not be used.
In instances of difficult joints use P.T.F.E.

Tape. The use of compound invalidates
the guarantee.

6. All plumbing connections must be
completed before making the electrical
connections.

7. The outlet of your shower acts as a
vent and must NOT be connected to
any form of tap or fitting not
recommended by Applied Energy
Products Ltd.

8. Always switch OFF at the isolating
switch when not in use.

The following points will help you to
understand how your Galaxy shower unit
operates.

The flow rate of water passing through the
shower unit determines the water
temperature. The lower the flow the
warmer the water, the higher the flow the
cooler the water.

The temperature produced by the shower
unit will vary between seasons on any one
setting of the temperature control. This is
due to variance in the temperature of the
water supply, which becomes cooler in
winter than summer.

The stabiliser valve maintains an almost
constant shower temperature during mains
water pressure changes.

If changes in temperature are experienced
in normal use, it is likely to be caused by
water pressure falling below the minimum
level. Falls in water pressure may be due
to water being drawn off at other points
within the building.

The shower head must be cleaned
regularly to remove scale and debris. If the
water becomes hot and you are unable to
obtain cooler water, check the shower head
for blockage.

2

SECTION

GENERAL ADVICE TO
SHOWER UNIT USERS

1

SECTION

PACKING CONTENTS