Extractor hood
AW 280190/280120
AW 281190/281120
Gaggenau Operating and installation instruction
2
Fig. 1
GAS
Abb. 1
ELECTRIC
3
Operating Instructions
Operating modes 4
Exhaust-air mode 4
Circulating-air mode 4
Coanda effect 5
Operating for the First Time 6
If you encounter a problem 6
Safety instructions 7
Operating procedure 8
Intensive setting 9
Special functions 9
Filters and maintenance 10
Grease filters 10
Saturation indicator F 10
Activated carbon filter 11
Cleaning and care 12
Replacing the light bulbsn 13
Installation Instructions
Important information 15
Prior to installation 16
Exhaust-air mode 16
Circulating-air mode 17
Preparing the wall 18
Electrical connection 19
Installation 20
Table of Contents
Exhaust-air mode
•
Installation accessories for exhaust air
mode.
Ventilation duct
AD280/281-012 for ceiling heights of
2.25–2.62 m
AD280/281-022 for ceiling heights of
2.62–3.01 m.
•
The extractor-hood fan extracts the
kitchen vapours and conveys them through the
grease filter into the atmosphere.
•
The grease filter absorbs the solid
particles in the kitchen vapours.
•
The kitchen is kept almost free of grease and
odours.
When the extractor hood is operated in exhaustair mode simultaneously with a different burner
which also makes use of the same chimney (such
as gas, oil or coal-fired heaters, continuous-flow
heaters, hot-water boilers) care must be taken to
ensure that there is an adequate supply of fresh
air which will be needed by the burner for
combustion.
Safe operation is possible provided that the
underpressure in the room where the burner is
installed does not exceed 4 Pa (0.04 mbar).
This can be achieved if combustion air can flow
through non-lockable openings, e.g. in doors,
windows and via the air-intake/exhaust-air wall box
or by other technical measures, such as reciprocal
interlocking, etc.
If the air intake is inadequate, there is a risk of
poisoning from combustion gases which are
drawn back into the room.
An air-intake/exhaust-air wall box by itself is no
guarantee that the limiting value will not be
exceeded.
Note: When assessing the overall requirement, the
combined ventilation system for the entire
household must be taken into consideration. This
rule does not apply to the use of cooking
appliances, such as hobs and ovens.
Unrestricted operation is possible if the extractor
hood is used in recirculating mode – with activated
carbon filter.
Circulating-air mode
•
Installation accessories for circulating air
mode.
Ventilation duct
AD280/281-112 for ceiling heights of
2.36–2.62 m
AD280/281-122 for ceiling heights of
2.62–3.01 m.
•
An activated carbon filter must be fitted for this
operating mode (see Filters and maintenance).
•
The extractor-hood fan extracts the kitchen
vapours which are purified in the grease filter
and activated carbon filter and then conveyed
back into the kitchen.
•
The grease filter absorbs the grease
particles in the kitchen vapours.
•
The activated carbon filter binds the odorous
substances.
몇 If no activated carbon filter is installed, it is not
possible to bind the odorous substances in the
cooking vapours.
Operating modes
4
Coanda effect
•
You do not need to activate the Coanda effect.
The Coanda air flow is always active at every
fan level. Cooking vapours are extracted
particularly well at the front of the cooking field.
•
The Coanda effect may allow you to operate the
extractor hood at a lower, quieter level than you
were previously accustomed to.
•
The Coanda air flow exits the top of the
extractor hood’s front panel. Do not place any
objects on the extractor hood: these may
disrupt the Coanda effect.
5
6
The Instructions for Use apply to several versions of
this appliance. Accordingly, you may find
descriptions of individual features that do not apply
to your specific appliance.
This extractor hood complies with all relevant safety
regulations.
Repairs should be carried out by qualified
technicians only.
Improper repairs may put the user at considerable
risk.
Before using your appliance for the first time,
please read these Instructions for Use carefully.
They contain important information concerning your
personal safety as well as on use and care of the
appliance.
Please retain the operating and installation
instructions for a subsequent owner.
This appliance is labelled in accordance
with European Directive 2002/96/EG
concerning used electrical and electronic
appliances (waste electrical and electronic
equipment – WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
If an F appears in the display:
•
See "Filters and maintenance" Section.
If is not possible to operate the extractor hood:
•
Disconnect the extractor hood from the mains
electricity supply by pulling out the plug or
switching it off at the main fuse box.
Wait for approx. 1 minute and then switch it on
again.
If you have any questions or if a fault occurs, please
call Customer Service.
(See list of Customer Service representatives).
When you call, please quote the following:
Enter the relevant numbers into the box above. The
E-Nr. (product no.) and FD (production date) are
shown on the nameplate which can be seen inside
the extractor hood after the filter frame has been
detached.
몇 The manufacturer of the extractor hoods
accepts no liability for complaints which can be
attributed to the design and layout of the
pipework.
Operating for the First Time If you encounter a problem
E-Nr. FD
7
Do not flambé food directly under the extractor
hood.
Risk of grease filter catching fire due to flames.
The hotplates must always be covered with a
utensil.
The extractor hood must not be operated above a
solid-fuel or gas fire (coal, wood, etc.) (see
installation instructions).
Do not operate all hotplates simultaneously over a
prolonged period (max. 15 minutes) at maximum
thermal load, otherwise there is a risk of burns from
touching the housing surfaces or a risk of damaging
the extractor hood. When operating the extractor
hood above a hob, operate the hood at maximum
setting if three or more hotplates are on at the same
time.
Do not use the appliance if damaged.
The appliance is not intended for use by young
children or infirmed persons without supervision.
Young children should be supervised to ensure they
do not play with the appliance.
If the connecting cable for this appliance is
damaged, the cable must be replaced by the
manufacturer or his customer service or a similarly
qualified person in order to prevent serious injury to
the user.
The appliance may be connected to the mains by a
qualified technician only.
Dispose of packaging materials properly (see
Installation instructions).
Never allow children to play with the appliance.
Do not let adults or children operate the appliance
unsupervised:
– if they are mentally or physically unable
to use the appliance safely and correctly,
– if they don’t have the knowledge and
experience to use the appliance safely
and correctly.
This extractor hood is designed for domestic use
only.
Light bulbs must always be fitted when the extractor
hood is in use.
Defective bulbs should be replaced immediately to
prevent the remaining bulbs from overloading.
Never operate the extractor hood without a grease
filter.
Overheated fat or oil can easily catch fire.
If you are cooking with fat or oil, e.g. chips, etc.,
never leave the cooker unattended.
Carefully clean the extractor hood before switching
on for the first time.
Do not place any objects on the extractor hood.
The slot for the Coanda air flow must be free at all
times.
Safety instructions
$
8
Operating procedure
Fan OFF
Saturation indicator
Light
Fan follow-on
Intensive setting
The most effective method of removing vapours
produced during cooking is to:
•
Switch the ventilator ON as soon as you begin
cooking.
•
Switch the ventilator OFF a few minutes after
you have finished cooking.
Fam settings
Switching the fan ON:
•
Press the 1, 2, 3 or Int button.
Switching the fan OFF:
•
Press the 0 button.
Intensive setting
Maximum power is obtained at the intensive setting.
It is only required for short intervals.
•
The Int key for the intensive level should be
pressed when browning and frying in an open
pan.
If you have switched on the hood by selecting
the intensive level, it will be switched off again
automatically after 5 minutes.
•
If you press the Int key while the hood is
running at fan level 1, 2 or 3, the electronic
control will switch back automatically to the
previously selected fan level after 5 minutes.
•
If you would like to end the intensive level
before the five minutes have elapsed, press the
0 key (“Motor off”) or select a different level. It
is possible to switch off the extraction function
at any time by pressing the 0 key (motor “off”).
Special functions
Intensive time:
•
You can set the intensive level running time to
3, 5 or 10 minutes by simultaneously pressing
the Int key and the 1, 2 or 3 key and you can
store this setting. When delivered, the
appliance is set to five minutes, i.e. the
combination of the Int key and the key 2.
Fan follow-on:
•
Delayed shut-off is possible at any level. First
press the required key 1, 2, 3 or Int and then
press the key.
The delayed shut-off time for all levels is ten
minu-tes. After these ten minutes, the
ventilation switches off, but the lighting stays
on.
Interval ventilation:
•
Interval ventilation is a special feature of this
appliance which periodically activates the fan
for five minutes every hour. You can activate
this function by simultaneously pressing the 0
key and, depending on the required extraction
capacity, the 1, 2 or 3 key.
This mode of operation is indicated by
alternating illumination of the key together
with the corresponding fan level indicator.
You can switch off interval ventilation by
pressing the 0 key.
Lighting:
•
Briefly press the button to switch the light
on and off.
•
The light can be switched on at any time, even
though the fan is switched off.
•
Adjusting the brightness:
Hold down the button until the desired
brightness is obtained.
9
10
Grease filters
Metal filters are used to trap the greasy element
of the vapours that develop during cooking.
The filter mats are made from non-combustible
metal.
Caution:
As the filter becomes more and more saturated with
grease, not only does the risk of it catching fire
increase but the efficiency of the extractor hood
can also be adversely affected.
Important:
By cleaning the metal grease filters at appropriate
intervals, the possibility of them catching fire as a
result of a build-up of heat such as occurs when
deep-fat frying or roasting is taking place, is
reduced.
Saturation indicator: F
The grease filter saturation display F flashes
after an operating time of 30 hours to you
indicate to you that you should clean the grease
filter. The grease filters can of course be cleaned
at any time, even if the grease filter saturation
display has not started to flash.
Cleaning the metal grease filters:
•
In normal operation (1 to 2 hours daily), the
metal grease filter must be cleaned
1 x a month.
•
The filters can be cleaned in a dishwasher. It is
however possible that they will become slightly
discoloured.
•
The filter must be placed loosely, and NOT
wedged, in the dishwasher.
Important:
Metal filters that are saturated with grease
should not be washed together with other
dishes etc.
•
When cleaning the filters by hand, soak them in
hot soapy water first of all.
Do not use aggressive, acidic or caustic
cleaners.
Then brush the filters clean, rinse them
thoroughly and leave the water to drain off.
Removing and inserting the metal grease filters:
IMPORTANT: The lighting must be switched OFF
and cool.
1 Press the catch on the grease filters inwards
and fold the filters down.
At the same time take hold of the underside of
the grease filters with your other hand.
2 Clean the filters.
3 Insert the clean filters back into the hood.
4 Cancel the F in the display.
– Press the button F.
Filters and maintenance
11
Activated carbon filter
For neutralizing odours in recirculating mode.
Caution:
As the filter becomes more and more
saturated with grease, there is an increased risk of
fire and the function of the extractor hood may be
impaired.
Important:
Change the activated carbon filter promptly to
prevent the risk of fire from the
accumulation of heat when deep-fat frying or
roasting.
Installation and removal:
IMPORTANT: The lighting must be switched OFF
and cool..
1 Remove the metal-mesh filters (see "Removing
and inserting the metal-mesh grease filters").
2 Insert the activated carbon filter.
3 Insert the metal grease filters (see "Removing
and inserting the metal grease filters").
Replacing the activated carbon filter:
•
During normal operation (1 to 2 hours per day)
the activated carbon filters should be replaced
approximately 1 x year.
•
A replacement filter can be obtained from any
authorized dealer (see optional
accessories).
•
Use original filters only.
By doing so you will obtain maximum
performance from your extractor hood.
Disposing of the old activated carbon filter:
•
There are no pollutants in the activated carbon
filters. They can therefore be
disposed of as part of your normal domestic
refuse.
12
Isolate the extractor hood by pulling out the
mains plug or switching off the fuse.
몇 Do not clean the extractor hood with abrasive
sponges or with cleaning agents which contain
sand, soda, acid or chlorine!
•
Clean the extractor hood with a hot soap
solution or a mild window cleaner.
Wichtig: Es darf keine Flüssigkeit in den Schlitz
für den Luftaustritt eindringen.
•
Do not scrape off dried-on dirt but wipe off with
a damp cloth.
•
When cleaning the grease filters, remove
grease deposits from accessible parts of the
housing. This prevents the risk of fire and
ensures that the extractor hood continues
operating at maximum
efficiency.
몇 Clean the operating buttons with a mild soapy
solution and a soft, damp cloth only.
Do not use stainless-steel cleaner to clean the
operating buttons.
Stainless steel surfaces:
•
Use a mild non-abrasive stainless steel cleaner.
•
Clean the surface in the same direction as it
has been ground and polished.
•
We recommend our stainless steel cleaner no.
461731.
See enclosed service booklet for order
address.
Aluminium, coated and plastic surfaces:
•
Do not use dry cloths.
•
Use a mild window cleaning agent.
•
Do not use aggressive, acidic or caustic
cleaners.
Observe the warranty regulations in the enclosed
service booklet.
Cleaning and care
13
1 Switch the extractor hood off and isolate it by
removing the mains plug or by switching off the
fuse.
몇 When operating, the fluorescent light bulbs get
very hot. Even after a while, there is still a risk of
being burnt.
2 Remove the metal-mesh filters (see "Removing
and inserting the metal-mesh grease filters").
3 Loosen the screws for the mounting rails..
4 Carefully remove the glass panes.
5 Remove the sockets for the fluorescent light
bulbs.
6 Replace the fluorescent light bulbs with new
ones available commercially (36 W, 840 Cool
White, socket 2 G 11).
몇 Risk of breakage!
Replacing the light bulbs
14
7 Insert the sockets for the fluorescent light
bulbs.
8 Carefully mount the glass panes.
9 Tighten the screws for the mounting rails.
10 Insert the metal grease filters (see "Removing
and inserting the metal grease filters").
11 Restore the power by inserting the mains plug
or switching on the fuse.
Note: If the light does not function, check that the
bulbs have been inserted correctly.
15
Old appliances are not worthless rubbish. Valuable
raw materials can be reclaimed by recycling old
appliances. Before disposing of your old appliance,
render it unusable.
You received your new appliance in a protective
shipping carton. All packaging materials are
environmentally friendly and recyclable. Please
contribute to a better environment by disposing of
packaging materials in an environmentally-friendly
manner.
Please ask your dealer or inquire at your local
authority about current means of disposal.
The extractor hood can be used in exhaust air or
circulating air mode.
Always mount the extractor hood over the centre of
the hob.
Minimum distance between electric hob and bottom
edge of extractor hood 550 mm, Fig. 1.
The extractor hood must not be installed over a
solid fuel cooker – a potential fire hazard (e.g. flying
sparks) – unless the cooker features a closed, non-
removable cover and all national regulations are
observed.
The smaller the gap between the extractor hood and
hotplates, the greater the likelihood that droplets
will form on the underside of the extractor hood.
Additional information concerning gas cookers:
When installing gas hotplates, comply with the
relevant national statutory regulations (e.g. in
Germany: Technische Regeln Gasinstallation
TRGI).
Always comply with the currently valid regulations
and installation instructions supplied by the gas
appliance manufacturer.
Only one side of the extractor hood may be installed
next to a high-sided unit or high wall. Gap at least
50 mm.
Minimum distance on gas hotplates between the
upper edge of the trivet and lower edge of the
extractor hood: 650 mm, Fig. 1.
Important information
$
Exhaust-air mode
•
Installation accessories for exhaust air
mode.
Ventilation duct
AD280/281-012 for ceiling heights of
2.25–2.62 m
AD280/281-022 for ceiling heights of
2.62–3.01 m.
16
Prior to installation
The exhaust air is discharged upwards through a
ventilation shaft or directly through the outside wall
into the open.
Exhaust air should neither be directed into a smoke
or exhaust flue that is currently used for other
purposes, nor into a shaft that is used for
ventilating rooms in which stoves or fireplaces are
also located.
Exhaust air may be discharged in accordance
with official and statutory regulations only (e.g.
national building regulations).
Local authority regulations must be observed when
discharging air into smoke or exhaust flues that are
not otherwise in use.
When the extractor hood is operated in exhaustair mode simultaneously with a different burner
which also makes use of the same chimney (such
as gas, oil or coal-fired heaters, continuous-flow
heaters, hot-water boilers) care must be taken to
ensure that there is an adequate supply of fresh
air which will be needed by the burner for
combustion.
Safe operation is possible provided that the
underpressure in the room where the burner is
installed does not exceed 4 Pa (0.04 mbar).
This can be achieved if combustion air can flow
through non-lockable openings, e.g. in doors,
windows and via the air-intake/exhaust-air wall box
or by other technical measures, such as reciprocal
interlocking, etc.
If the air intake is inadequate, there is a risk of
poisoning from combustion gases which are
drawn back into the room.
An air-intake/exhaust-air wall box by itself is no
guarantee that the limiting value will not be
exceeded.
Note: When assessing the overall requirement, the
combined ventilation system for the entire
household must be taken into consideration. This
rule does not apply to the use of cooking
appliances, such as hobs and ovens.
Unrestricted operation is possible if the extractor
hood is used in recirculating mode – with activated
carbon filter.
If the exhaust air is going to be discharged into
the open, a telescopic wall box should be fitted into
the outside wall.
Exhaust-air
650-
1410
17
For optimum extractor hood efficiency:
•
Short, smooth air exhaust pipe.
•
As few bends in the pipe as possible.
•
Diameter of pipe to be as large as possible and
no tight bends in pipe.
If long, rough exhaust-air pipes, many pipe
bends or smaller pipe diameters are used,
the air extraction rate will no longer be at an
optimum level and there will be an increase
in noise.
몇 The manufacturer of the extractor hoods
accepts no liability for complaints which can
be attributed to the design and layout of the
pipework.
•
Round pipes:
We recommend
Internal diameter: 150 mm.
•
Flat ducts must have an internal cross-section
that equates to that of round pipes.
There should be no sharp bends.
l 150 mm approx. 177 cm
2
•
If pipes have different diameters: Insert
sealing strip.
•
For exhaust-air mode, ensure that there is an
adequate supply of fresh air.
Connecting a l 150 mm exhaust-air pipe:
•
Mount the pipe directly
onto the air outlet on the
hood.
Circulating-air mode
•
Installation accessories
for circulating air mode.
Ventilation duct
AD280/281-112 for
ceiling heights of 2.36–
2.62 m
AD280/281-122 for
ceiling heights of 2.62–
3.01 m.
•
With activated carbon filter if exhaust-air mode
is not possible.
Recirculating-air
760-
1410
Preparing the wall
•
The wall must be flat and perpendicular.
•
Make sure that the wall can bear the applied
loads.
•
The provided screws and wall plugs are
suitable for solid masonry. On all other wall
types (e.g. plasterboard, porous concrete,
Poroton bricks) use the appropriate fasteners.
•
Ensure that the wall is capable of providing a
firm hold for mounting
screws and plugs.
Weight in kg:
We reserve the right to construction changes within
the context of technical development.
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: Fitting a Different Plug:
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow – Earth
Blue – Neutral
Brown – Live
If you fit your own plug, the colours ofthese wires
may not correspond with the identifying marks on
the plug terminals.
This is what you have to do:
1 Connect the green and yellow (Earth) wire to
the terminal in the plug marked ‘E’ or with the
symbol ( ), or coloured green or green and
yellow.
2 Connect the blue (Neutral) wire to the terminal
in the plug marked ‘N’ or coloured black.
3 Connect the brown (Live) wire to the terminal
marked ‘L’, or coloured red.
The extractor hood should only be con-nected to
an earthed socket that has been installed
according to relevant regulations.
If possible, site the earthed socket directly behind
the chimney panelling.
•
The earthed socket should be connected via its
own circuit.
•
If the earthed socket is no longer accessible
following installation of the extractor hood,
ensure that there is a permanently installed
disconnector.
If it is necessary to wire the extractor hood
directly into the mains:
The extractor hood should only be connected to the
electricity supply by a properly qualified electrician.
A separator must be installed in the household
circuit. A suitable separator is a switch that has a
contact gap of more than 3 mm and interrupts all
poles. Such devices include circuit breakers and
contactors.
몇 If the connecting cable for this
appliance is damaged, the cable must be replaced
by the manufacturer or his customer service or a
similarly qualified person in order to prevent serious
injury to the user.
Electrical connection
18
Exhaust-air Recirculating air
32,0090 cm
120 cm
34,0
36,0 38,0
Electrical data
Are to be found on the name plate inside the
appliance after removal of the filter frame.
몇 Before undertaking any repairs, always
disconnect the extractor hood from the electricity
supply.
Length of the connecting cable: 1.30 m.
This extractor hood corresponds to EC regulations
concerning RF interference
suppression..
19
20
This extractor hood is intended to be mounted onto
the kitchen wall.
1 Remove the grease filter (refer to Operating
Instructions).
2 Draw a line on the wall from the ceiling to the
lower edge of the hood at the centre of the
location where the hood is going to be
mounted.
3 Use the template to mark the points on the wall
where the screws will be mounted. In order to
make it easier to hook the hood onto the
screws, draw the outline of the area where the
hood will be attached.
몇 Ensure that the minimum distance between the
hob and the extractor hood is maintained – 550 mm
for an electric hob and 650 mm for a gas hob. The
bottom edge of the template equates to the lower
edge of the extractor hood.
4 Drill 2x 8 mm ø holes for the upper fixing
bracket and 2x 8 mm ø holes for the lower fixing
bracket and press in wall plugs flush with the
wall..
Note: Take into account any special accessories
that are going to be fitted.
5 Screw on the upper and the two lower fixing
brackets.
Installation
21
6 Attach the extractor hood.
Adjust the height and align horizontally with the
adjusting screws.
몇 Check that the 4 lower fixing holes have
been correctly marked. If required, mark again..
7 Remove the extractor hood. Drill the 4 lower
8 mm ø fixing holes and press in the wall plugs
flush with the wall..
8 Attach the extractor hood and screw into
position with the remaining 4 screws.
9 Stick protective film over the holes of the 2
lower mounting bolts in the protective grid.
10 Connect up the air outlet pipe.
11 Connect the hood to the electricity supply.
22
12 Carefully remove the protective foil.
몇 Avoid damage to the sensitive surface.
Warning: The interior walls of the flue panelling can
have sharp edges – Risk of injury –.
We recommend that you wear gloves when
installing.
13. Insert the upper flue duct into the lower flue
duct.
n Protect the cover panels from scratches, for
example by laying the template used for marking
the wall over the top edge of the lower section.
14. Insert the complete flue duct at an angle and
swivel to the rear.
15 Carefully pull the upper flue duct upwards and
screw the sides to the fixing bracket with
2 screws.
16 Insert the grease filter (refer to Operating
Instructions).
23
KF001-010
Gaggenau Hausgeräte GmbH
Carl-Wery-Straße 34
D-81739 München
www.gaggenau.com
9000247018 EB 8709 en
Loading...