Gaggenau AW230790 User Manual

Gaggenau

Use and care manual Guide d’utilisation et d’entretien Manual de uso y cuidado

AW 230 790

HOOD AW 230 790 Hotte aspirante AW 230 790 Campana extractora AW 230 790

Table of Contents

Use and care manual

Instructions for use 2

Safety Definitions 3 IMPORTANT SAFETY INSTRUCTIONS 4

General notes 4 Fire Safety 4 Burn Prevention 5 Child Safety 5 Cleaning Safety 6 Safe use 6 Proper Installation and Maintenance 6

State of California Proposition 65 Warnings 7 Causes of damage 8 Protecting the environment 8 Operating modes 8

Exhaust air mode 8

Circulating-air mode 8 Operation 9

Operating the appliance 9

Turn on the fan 9

Intense level 9

Run-on function 9

Interval ventilation 9

Lighting 10

Saturation notification 10 Cleaning and maintenance 10 Troubleshooting 12 Customer service 12

Accessories for circulating-air mode 12

Instructions for use

Installation Instructions 13

IMPORTANT SAFETY INSTRUCTIONS 14

Appliance Handling Safety 15 Safety Codes and Standards 15 Electric Safety 15 Related Equipment Safety 16

Before You Begin 17

Tools and Parts Needed 17 Parts Included 17 Appliance dimensions 17 Safety clearances 18

General notes 18

Exhaust air mode 18 Ventilation line 18

Check wall 19 Electrical connection 19 Installation 20

Preparing the installation 20

Installation 20

Attaching and aligning the appliance 21

Attaching flue duct 21

Additional information on products, accessories, replacement parts and services can be found at

www.gaggenau.com and in the online shop www.gaggenau-eshop.com

Safety Definitions

9 WARNING

This indicates that death or serious injuries may occur as a result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.

Note: This alerts you to important information and/or tips.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION

READ AND SAVE THESE INSTRUCTIONS

WARNING

When properly cared for, your new appliance has been designed to be safe and reliable. Read all instructions carefully before use. These precautions will reduce the risk of burns, electric shock, fire, and injury to persons. When using kitchen appliances, basic safety precautions must be followed, including those in the following pages.

General notes

Examine the appliance after unpacking it. In the event of transport damage, do not plug it in.

Fire Safety

Always have a working smoke detector near the kitchen.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low

or medium settings. b) Always turn hood ON when cooking at high heat. c) Clean ventilating fans frequently. Grease should

not be allowed to accumulate on fan or filter. d) Use proper pan size. Always use cookware

appropriate for the size of the surface element. Do not flambé under the extractor hood or work with a naked flame. When switched on, the extractor hood draws flames into the filter. There is a risk of fire due to deposits on the grease filter!

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

In the event that personal clothing or hair catches fire, drop and roll immediately to extinguish flames.

Smother flames from food fires other than grease fires with baking soda. Never use water on cooking fires.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: ‒ SMOTHER FLAMES with a close-fitting lid,

cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

‒ NEVER PICK UP A FLAMING PAN – You may be

burned.

‒ DO NOT USE WATER, including wet dishcloths

or towels – a violent steam explosion will result.

‒ Use an extinguisher ONLY if:

‒ You know you have a Class ABC extinguisher,

and you already know how to operate it.

‒ The fire is small and contained in the area

where it started.

‒ The fire department is being called ‒ You can fight the fire with your back to an exit.

Have an appropriate fire extinguisher available, nearby, highly visible and easily accessible near the appliance.

Whenever possible, do not operate the ventilation system during a cooktop fire. However, do not reach through fire to turn it off.

WARNING

Risk of fire

Grease deposits in the grease filter can ignite.

Clean the grease filter at least every two months.

Never operate the appliance without the grease filter.

Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.

Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING

Risk of fire

Grease deposits in the grease filter can catch fire. Never work with a naked flame near the appliance (e.g. flambéing). Install the unit near a heat-producing appliance for solid fuels (e.g. wood or coal) only if there is a closed, non-detachable cover. There must be no flying sparks.

WARNING

Risk of fire

When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.

WARNING

Risk of fire

During simultaneous use of multiple gas cooktops, a great deal of heat is created. A ventilation device located above it can become damaged or catch fire. Never use two gas cooktops together at maximum heat for longer than 15 minutes. One large burner with over 17,000 Btu/hr (5 kW) (wok) is equal to the wattage of two gas burners.

WARNING

Risk of fire

Hot oil and fat catch fire fast. Never leave hot oil and fat unsupervised. Never extinguish a fire with water. Switch off the cooking position. Suffocate flames carefully with a lid, a fire blanket or similar.

Burn Prevention

WARNING

Risk of burns

The accessible parts get hot during operation. Never touch hot parts. Keep children away.

Child Safety

When children become old enough to use the appliance, it is the legal responsibility of the parents or legal guardians to ensure that they are instructed in safe practices by qualified persons.

Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material.

WARNING

Risk of fire

Operating several gas burners at the same time gives rise to a great deal of heat. The ventilation appliance may become damaged or catch fire. The ventilation appliance must only be combined with gas burners that do not exceed the maximum total output of 61,000 Btu/hr (18 kW). If 41,000 Btu/hr (12 kW) is exceeded, the local regulations concerning room ventilation, room size, and combination with ventilation devices in exhaust and recirculating operation must be heeded.

Do not allow anyone to climb, stand, lean, sit, or hang on any part of an appliance, especially a door, warming drawer, or storage drawer. This can damage the appliance, and the unit may tip over, potentially causing severe injury.

Do not allow children to use this appliance unless closely supervised by an adult. Children and pets should not be left alone or unattended in the area where the appliance is in use. They should never be allowed to play in its vicinity, whether or not the appliance is in use.

CAUTION

Items of interest to children should not be stored in an appliance, in cabinets above an appliance or on the backsplash. Children climbing on an appliance to reach items could be seriously injured.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Cleaning Safety

WARNING

Be sure the entire appliance (including the grease filters and light bulbs, if applicable) has cooled and grease has solified before attempting to clean any part of the appliance.

Do not use steam cleaners to clean the appliance.

Safe use

WARNING

Do not repair, replace or remove any part of the appliance unless specifically recommended in the manuals. Improper installation, service or maintenance can cause injury or property damage. Refer to this manual for guidance. All other servicing should be done by a qualified technician.

use. See the Warranty. If you have any questions, contact the manufacturer.

Do not store or use corrosive chemicals, vapors, flammables or nonfood products in or near this appliance. It is specifically designed for use when heating or cooking food. The use of corrosive chemicals in heating or cleaning will damage the appliance and could result in injury.

Do not operate this appliance if it is not working properly, or if it has been damaged. Contact an authorized servicer.

Do not repair or replace any part of the appliance unless specifically recommended in this manual. Refer all servicing to a factory authorized service center.

CAUTION

Grease left on filters can remelt and move into the vent.

CAUTION

WARNING

Risk of injury

Items placed on the appliance may fall down. Do not place any objects on the appliance.

WARNING

Risk of injury

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

Proper Installation and Maintenance

Have the installer show you the location of the circuit breaker or fuse. Mark it for easy reference.

This appliance must be properly installed and grounded by a qualified technician. Connect only to properly grounded outlet. Refer to Installation Instructions for details.

Turn power off at breaker before removing a damaged bulb. Do not touch the bulbs immediately after use. The bulbs will remain hot for several minutes.

WARNING

Make sure the appliance and lights are cool and power to the appliance has been turned off before replacing the light bulb(s). Failure to do so could result in electrical shock or burns.The lenses (if equipped) must be in place when using the appliance.The lenses (if equipped) serve to protect the light bulb from breaking.The lenses (if equipped) are made of glass. Handle carefully to avoid breaking. Broken glass can cause an injury.

Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

This appliance is intended for normal family household use only. It is not approved for outdoor

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING

When the hood is operated in exhaust-air mode simultaneously with a different burner which also makes use of the same chimney (such as gas, oil or coal-fired heaters, continuous-flow heaters, hot-water boilers) care must be taken to ensure that there is an adequate supply of fresh air which will be needed by the burner for combustion. Safe operation is possible provided that the under pressure in the room where the burner is installed does not exceed 4 Pa (0.04 mbar). This can be achieved if combustion air can flow through non-lockable openings, e.g. in doors, windows and via the air-intake/exhaust-air wall box or by other technical measures, such as reciprocal interlocking, etc.

WARNING

Avoid carbon monoxide poisoning – Provide adequate air intake so combustion gases are not drawn back into the room. An air-intake/exhaust-air wall box by itself is no guarantee that the limiting value will not be exceeded.

Note: When assessing the overall requirement, the combined ventilation system for the entire household must be taken into consideration. This rule does not apply to the use of cooking appliances, such as cooktops and ovens.

State of California Proposition 65 Warnings

WARNING

This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Causes of damage

Operating modes

NOTICES:

▯ Risk of damage due to corrosion. Always turn

appliance on when cooking to avoid condensation

buildup. Condensation can lead to corrosion

damages.

▯ Risk of damage due to ingress of humidity into the

electronic circuitry. Never clean operator controls

with a wet cloth.

▯ Surface damage due to incorrect cleaning. Clean

stainless steel surfaces in the grind direction

only. Do not use any stainless steel cleaners for

operator controls.

▯ Surface damage due to strong or abrasive

cleaning agents. Never use strong and abrasive

cleaning agents.

▯ Risk of damage from condensation back flow.

Install exhaust vent at a slight downward slope

away from the appliance (1° slope).

Protecting the environment

You can use this appliance in the air extraction or the recirculation mode.

Exhaust air mode

The air that is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

Note: Ventilation may not exit through an already operational smoke or exhaust chimney, nor a duct used for ventilating furnace installation areas.

▯ If the ventilation is intended to pass through a

smoke or exhaust that is not in operation, the responsible area heating inspector must give approval.

▯ If the ventilation passes through an external wall,

use a telescope wall sleeve.

Circulating-air mode

Unpack the appliance and dispose of the packaging in line with environmental requirements.

The air that is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

Note: To bind odors in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist retailers, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use.

Operation

Note: Turn the extractor hood on when you start

cooking and switch it off again a few minutes after you have finished cooking. This is the most effective way to eliminate cooking vapor.

Operating the appliance

Control panel

Intense level

For especially strong odor or vapor, use the intense level.

1 Press the ÿ button to switch on the appliance.

The fan starts in setting 2.

2 Press the Ž button to switch on the Intensive

setting. Note: If the button was pressed while the fan is

running on speed 1, 2 or 3, the electronics automatically switch back to the previouslyselected fan speed after 5 minutes.

3 To switch off the Intensive setting earlier, press

the ÿ button or the button for another fan speed.

Setting the duration

Explanation

Fan On/off

1 Fan speed 1 2 Fan speed 2 3 Fan speed 3

Intensive setting

Run-on funcion

Saturation display

Light on/off

Turn on the fan

Switching on

For extraction there are three ventilator speeds and an Intensive setting available.

1 Press the ÿ button to switch on the appliance.

The fan starts in setting 2. 2 With the buttons 1, 2, 3 or Ž, set the fan speed

according to the cooking situation.

Switching off

Use the ÿ button to switch the appliance off.

You can set the duration after which the Intensive setting switches off automatically.

Duration Press buttons simultaneously

3 minutes 5 minutes 10 minutes

The factory setting is set to 5 minutes.

Ž and 1 Ž and 2 Ž and 3

Run-on function

The run-on function can be set for any fan speed.

1 First press the button for the desired fan speed 1,

2, 3 or Ž and then press the ž button.

Notes

‒ The run-on time is ten minutes for all fan speed

settings. Once this time has elapsed, ventilation switches off automatically.

‒ If the lighting is switched on, it remains on.

2 To switch off the run-on function earlier, press the

ÿ button.

Interval ventilation

For interval ventilation, the device is switched on automatically for five minutes per hour.

1 Press the ÿ button to switch on the appliance.

The fan starts at level 2. The interval ventilation can be used on level 1, 2 or 3.

2 Press the run-on button ž twice.

Note: This mode is indicated by alternating

lighting up of the ž button with the corresponding speed.

3 To end interval ventilation, press the ÿ button.

Lighting

The lighting can be switched on and off independently of the ventilation.

Cleaning and maintenance

Press the @ button.

Setting the brightness

Press and hold the @ button until the desired brightness is reached.

Saturation notification

After 30 hours of operation, the saturation display œ of the grease filter blinks.

▯ At the latest now the metal mesh grease filter

should be cleaned. For instructions on how to

clean the metal mesh grease filter, please see the

chapter about Cleaning and maintenance.

▯ While the saturation display is blinking, it can be

reset with the œ button.

9 WARNING

Risk of burns

The appliance will become hot when in use, especially in the area surrounding the bulbs. Let cool before cleaning.

9 WARNING

Risk of electric shock

Penetrating damp can cause electric shock. Only clean appliance with a damp cloth. Prior to cleaning, pull the plug or flip the breaker in the fusebox.

9 WARNING

Risk of electrical shock

Moisture entering the appliance can cause an electrical shock. Don't use a high-pressure cleaner or steam cleaner.

9 WARNING

Risk of injury

Components inside the appliance may have sharp edges. Wear protective gloves.

Cleaning agents

To prevent various surfaces from becoming damaged due to incorrect cleaning agents, follow the specifications given in the table. Do not use

▯ cleaning agents that are harsh or scouring, ▯ cleaning agents with high alcohol content, ▯ hard scouring pads or sponges, ▯ high-pressure cleaners or steam cleaners.

Thoroughly rinse all new sponges before use.

Observe all instructions and warnings accompanying cleaning agents.

Area Cleaning agents

Stainless steel Warm soapy water:

Clean with a dish rag and dry with a soft towel.

Only clean stainless steel with the grain.

Specific products for stainless steel care are available from customer service or from specialized retailers. Apply a thin layer of the care product with a soft cloth.

Varnished surfaces Warm soapy water:

Clean with a damp dish rag and dry with a soft towel.

Do not use stainless steel cleaner.

Aluminum and plastic

Glass Glass cleaner:

Controls Warm soapy water:

Glass cleaner: Clean with a soft cloth.

Clean with a soft cloth. Do not use a glass scraper.

Clean with a damp dish rag and dry with a soft towel.

Risk of damage to electronics due to permeating damp. Never clean controls with a wet cloth.

Do not use stainless steel cleaner.

In the dishwasher:

Note: Slight discoloration is possible when cleaning

the grease filters in the dishwasher. This does not affect the metal grease filter's functioning.

▯ Do not clean extremely dirty metal grease filters

with dishes.

▯ Loosely position the metal grease filter in the

dishwasher. The metal grease filters must not be jammed in.

By hand:

Note: You can use a special grease solvent if soiling

is stubborn. You can order it via the online shop.

▯ Soak the metal grease filters in hot soapy

solution.

▯ Use a brush for cleaning and then rinse the filters

well.

▯ Allow the metal grease filters to drip dry.

Uninstalling metal grease filter

1 Take metal mesh grease filter out of the holder. 2 Pull the metal grease filter downwards. While

doing this, place your other hand under the metal grease filter.

Cleaning the metal grease filter

These instructions apply to several appliance models. It is possible that individual features are described that do not apply to your appliance.

9 WARNING

Risk of fire

Grease deposits in the grease filter can ignite.

Clean the grease filter at least every two months.

Never operate the appliance without the grease filter.

Notes

‒ Do not use any aggressive, acidic or alkaline

cleaning agents. ‒ When cleaning the metal grease filters, also clean

the metal grease filter holder in the appliance

with a moist cloth. ‒ You can clean the metal grease filters in a

dishwasher or by hand.

Notes

‒ Grease can accumulate in the bottom of the

metal mesh grease filter.

‒ Do not hold metal mesh grease filter at an

angle, otherwise grease will drip out.

3 Clean the metal mesh grease filter.

Installing metal grease filter

1 Insert metal grease filter.

Simultaneously use your other hand to grasp under the metal grease filter.

2 Flip metal grease filter up and snap the latch into

place.

Troubleshooting

Customer service

You can often easily eliminate problems that may occur on your own. Before calling customer service, take into account the following information.

9 WARNING

Risk of electric shock

Improper repairs are dangerous. Only an aftersales technician trained by us may perform repairs and may replace damaged connecting leads. Remove the mains plug or deactivate the fuse in the fuse box if the appliance is defective. Call after-sales service.

Troubleshooting table

Disruption Possible cause Solution

Appliance is not working

--------

Plug is not plugged in

Power outage Check whether other

Fuse defective Check in the fuse box

Connect the appliance to the mains

kitchen appliances are working

whether the fuse for the appliance is in working order

LED lights

Defective LED lights may be replaced by the manufacturer, his customer service or a qualified technician (electrician) only.

If your appliance needs repairs, our customer service is there for you. We work hard to help solve problems quickly and without unnecessary service calls, getting your appliance back up and running correctly in the least amount of time possible.

When you call, please indicate the product number (E-Nr.) and serial number (FD-Nr.) so that we can support you in a qualified manner. The identification plate listing the numbers can be found inside of the appliance (remove metal grease filter to find it).

To avoid having to search for a long time when you need it, you can enter your appliance data and the customer support telephone number here.

E-Nr. FD-Nr.

Customer Service

Please read the use and care instructions provided with your appliance. Failure to do so may result in an error in using the appliance. This could result in a service call that instead of fixing a mechanical issue is only needed for customer education. Such calls are not covered by the appliance warranty.

Please find the contact data of all countries in the enclosed customer service list.

To book an engineer visit and product advice

USA 877 442 4436

CANADA 877 442 4436

toll-free

9 WARNING

Risk of injury

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched on LED lights for longer than 100 seconds.

You can rely on the manufacturer’s expertise. Rest assured that the repair will be handled by trained service technicians who have the original replacement parts for your appliance.

Accessories for circulating-air mode

(not included in the delivery)

Note: Follow the installation instructions supplied with the accessories.

Basic equipment

Throw-away filter

1 AA200812 2 AA200110

Installation Instructions

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE AFTER INSTALLATION IS COMPLETE.

IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

WARNING

If the information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury.

WARNING

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING ‒ Installation work and electrical wiring must be

done by qualified person(s) in accordance with all

applicable codes and standards, including fire-

rated construction. ‒ Sufficient air is needed for proper combustion

and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment

manufacturer’s guideline and safety standards

such as those published by the National Fire

Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local

code authorities. ‒ When cutting or drilling into wall or ceiling, do

not damage electrical wiring and other hidden

utilities. ‒ Ducted fans must always be vented to the

outdoors.

WARNING

The applicable regulations of the energy supply companies and the regional construction regulations must be observed when installing the hood.

WARNING

Risk of fire

WARNING

Risk of fire

WARNING

To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages.

WARNING

To reduce the risk of fire, use only metal ductwork.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING

Note: When assessing the overall requirement, the combined ventilation system for the entire household must be taken into consideration. This rule does not apply to the use of cooking appliances, such as cooktops and ovens.

WARNING

Risk of injury

The appliance may fall from the wall if it is not attached properly. All fastening components must be fixed firmly and securely in place.

Safety Codes and Standards

This appliance complies with the latest version of one or more of the following standards:

▯ UL 507 - Electric Fans ▯ CAN/CSA C22.2 No. 113 - Fans and Ventilators

Electric Safety

WARNING

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

Risk of damage from condensation back flow. Install exhaust vent at a slight downward slope away from the appliance (1° slope).

Appliance Handling Safety

Unit is heavy and requires at least two people or proper equipment to move.

Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

WARNING

Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.

WARNING

Before you plug in an electrical cord or turn on power supply, make sure all controls are in the OFF position.

For appliances equipped with a cord and plug, do not cut or remove the ground prong. It must be plugged into a matching grounding type receptacle to avoid electrical shock. If there is any doubt as to whether

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

the wall receptacle is properly grounded, the customer should have it checked by a qualified electrician.

If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit.

WARNING

To reduce the risk of fire or electric shock, do not use this fan with any solid-statespeed control device.

Installer – show the owner the location of the circuit breaker or fuse. Mark it for easy reference.

Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ‒ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer. ‒ Before servicing or cleaning unit, switch power

off at service panel and lock the service

disconnecting means to prevent power from being

switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Related Equipment Safety

Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material.

The appliance is only guaranteed safe to use if installed by a specialist in accordance with these installation instructions. The installer is liable for any damage resulting from incorrect installation.

Never modify or alter the construction of the appliance. For example, do not remove leveling legs, panels, wire covers or anti-tip brackets/screws.

Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable codes.

WARNING

Risk of electric shock

Parts inside the appliance can have sharp edges. The connection cable can be damaged. Do not bend or pinch connection cables during installation.

Before You Begin

Appliance dimensions

Tools and Parts Needed

▯ Measuring tape ▯ Pencil ▯ Phillips screwdriver (Posidrive) #2 ▯ Screwdriver T25 ▯ Screwdriver T15 ▯ Drill with the following bits: 5/16" (8 mm) ▯ Spirit-level ▯ Aluminum tape (DO NOT use insulating tape) ▯ Exhaust channel (configuration depends on the

installation situation)

▯ Additional sheet metal screws (if necessary for

installation of the exhaust air duct)

▯ Saw

Parts Included

PLQ  PD[







PLQ





DERYHHOHFWULF VXUpOHFWULTXH VREUHHOpFWULFR







PLQ 



DERYHJDV VXUJD] VREUHJDV

[

[

[

[

[

[

[

 PP

▯ This appliance is installed on the wall. ▯ Follow the enclosed installation instructions for

additional special accessories (e.g. for circulating-air mode).

▯ The surfaces of the appliance are sensitive. Avoid

damaging them during installation.

Safety clearances

9 WARNING

Risk of fire

Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric cooktops are operated together, the largest specified distance applies. Only one side of the appliance may be installed directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 2" (50 mm).

The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 30 " (760 mm) from electric cookers and 30 " (760 mm) from gas or mixed cookers.

If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.

General notes

Exhaust air mode

9 WARNING

Risk of death

Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft that is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used.

Ventilation line

Note: The appliance manufacturer does not assume

any warranty for complaints attributable to the pipe section.

▯ The appliance achieves its optimum performance

by means of a short, straight exhaust air pipe and as large a pipe diameter as possible.

▯ As a result of long rough exhaust air pipes, many

pipe bends or pipe diameters that are smaller than 6” (150 mm), the optimum extraction performance is not achieved and fan noise is increased.

▯ The pipes or hoses for laying the exhaust air line

must consist of non-combustible material.

Round pipes

An inner diameter of 6” (150 mm), but at least 4 _” (120 mm), is recommended.

Flat ducts

The inner cross-section must correspond to the diameter of the round pipes.

dia. 6” (150 mm) approx. 27^ sq in (177 cm

)

dia. 4 _” (120 mm) approx. 26_ sq in (113 cm2)

▯ Flat ducts should have no sharp deflections. ▯ Use sealing strip for deviating pipe diameters.

Check wall

▯ The walls must be smooth, vertical, and

sufficiently load-bearing.

▯ The depth of the bore holes must be the same

length as the screws. The wall plugs must have a

secure grip.

▯ The enclosed screws and wall plugs are suitable

for solid brickwork. Suitable fasteners must be

used for other structures (e.g. plasterboard,

porous concrete, poroton bricks).

▯ The max. weight of the extractor hood is 90 lbs

(40 kg)

Electrical connection

9 WARNING

Risk of electric shock

Parts inside the appliance can have sharp edges. The connection cable can be damaged. Do not bend or pinch connection cables during installation.

The necessary connection information is located on the identification plate in the appliance interior, remove metal grease filter to access it.

Length of the connecting cable: Approx. 4] ft (1.30 m)

This appliance meets EC radio interference suppression requirements.

9 WARNING

Risk of electric shock

It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been installed correctly. If the plug is no longer accessible following installation of the appliance, or a fixed connection is required, an all-pole isolating switch must be present on the installation side with a contact gap of at least

X” (3 mm). The fixed connection may only be

installed by an electrician.

Installation

1 Screw on the angle bracket for the flue duct. ¨

Preparing the installation

9 CAUTION

Ensure that there are no electric wires, gas or water pipes in the area where holes are to be made.

1 Mark a vertical center line on the wall from the

ceiling to the lower edge of the extractor hood. 2 Mark positions for the screws and the contour of

the attachment area. 3 Drill five 5/16" (8 mm) Ø holes to a depth of 3 5/32"

(80 mm) for the attachments and press in the wall

plugs flush with the wall.

ë

[



èç¼ȫȰ

é





[

2 Screw on brackets for the extractor hood hand-

[

ê







 PP

3 Screw in threaded bolt, leaving it protruding out

of the wall by

/16" - 11/32" (5–9 mm). ª

PLQç¼ȫȰ

PD[èè¼ȭȬ

 PP

Attaching and aligning the appliance

Connecting the pipes

1 Initially remove the protective foil from the back of

the appliance and, following installation, remove

foil completely. 2 When attaching the appliance, ensure that it

engages firmly with the brackets. « 3 Align the appliance horizontally by turning the

brackets. If required, the appliance can be moved

to the right or left. ¬

(

Note: If an aluminum pipe is used, smooth the connection area beforehand.

Exhaust-air pipe Ø 6” (150 mm) (recommended size)

Attach exhaust-air pipe directly to the air-pipe connector and seal.

Exhaust-air pipe Ø 4 _” (120 mm) 1 Attach reducing connector directly to the air-pipe

connector.

2 Attach exhaust air pipe to the reducing connector. 3 Seal both joints appropriately.

Attaching flue duct

9 WARNING

Risk of injury

From sharp edges during installation. Always wear protective gloves while installing the appliance.

4 Tighten the screws on the brackets holding the

brackets in place with one hand. ® 5 Screw on knurled nut and washer firmly. ¯

)

1 Separate the flue ducts.

To do this, remove the adhesive tape.

2 Remove the protective foil from both flue ducts. 3 Push one flue duct into the other.

Notes

‒ To prevent scratches, lay paper over the edges

of the lower flue duct to protect the surface.

‒ The slots of the inner flue duct point

downwards.

4 Place flue ducts on the appliance. 5 Push the inner flue duct upwards and attach it to

the angle brackets on the left and right. ¨

6 Press the flue duct downwards until it

engages. ©

+ 47 hidden pages