Remote
control unit
Panel
cover
Installation
cut-out
HOME/SETTINGS
key
Joystick/Rotokey
™
Event/GOTO
key
CURS/SCROLL
key
CANCEL/MOB
key
CTRL/Full Screen
key
EDGE Swipe/Switch MFD to Control
key
then
then
then
then
NAV INFO/F1
key
Gain/F2
key
AUTO/STBY
key
Brill
key
User's Guide
REMOTE CONTROL UNIT Model MCU-006/006H
Note: For the sake of brevity, this guide only shows the MCU-006. For MCU-006H users, the dimensions are the same,
however the indications on each button are oriented horizontally and appears slightly different from the images shown here.
The purpose of this guide is to provide the basic operation and
installation of the Remote Control Unit MCU-006/006H.
All brand and product names are trademarks, registered
trademarks or service marks of their respective holders.
How to Install the Remote Control Unit
Included items
Name
Remote Control Unit
Installation Materials CP002-21001
Accessories FP002-21001
Procedure
1. Using the flush mounting template (supplied), cut a mounting
hole in the installation site.
2. Fit the flush mount sponge to the rear of the unit.
3. Connect the NMEA 2000 cable to the remote control unit.
4. Set the unit into the hole and secure the unit with four
self-tapping screws (ø4×16, supplied).
5. Attach the panel cover.
6. Attach the sun cover.
7. Connect the NMEA 2000 connector to the same network as
the compatible MFD.
Type
MCU-006/006H
Qty
1
1
1
Outline and dimensions
59 mm
Self-tapping
screw (4 pcs)
22.6 mm
31 mm
Panel
cover
Remote
control unit
Installation
cut-out
Compatible equipment
TZT9F TZT12F TZT16F
TZT19 F TZT10X TZT13X
TZT16X TZT22X TZT24X
Note :
supported by V3.56 or later.
How to remove the panel cover
Insert a flat head screwdriver into each of the indicated
slots, in numerical order. Twist the screwdriver gently to
release each of the sides. Failure to release the sides
in order may damage the cover.
TZT9F/12F/16F/19F are
5
3
4
1
Specifications
Remote Control Unit MCU-006/006H
Ambient temperature
Relative humidity
Degree of protection
*
Mass
Power supply
*
: Mass does not include the sun cover.
2
-15 °C to +55 °C
93% or less at 40 °C
IP56 (front), IP55 (back)
0.15 kg
NMEA 2000 (Consumption
current: Max. 100 mA; LEN: 2)
Operational overview
1
2
4 5
150 mm
3
HOME/SETTINGS
1
Short press:
Goes to the Home page.
・
Joystick/Rotokey
2
Joystick, Roto key:
• Moves the cursor.
• Scrolls the screen.
• Zooms in, zooms out the display.
• Selects menus.
• Inputs numeric data.
Button:
• Confirms operation.
™
key
Long press:
· Opens the Settings screen.
7 mm
NMEA 2000
Connector
#65 mm
Notes
1. The table shown below indicates tolerance
of dimensions.
2. "#" indicates minimum service clearance.
3. Use self-tapping screws (ø4×16, included)
to secure the unit.
DIMENSIONS (mm)
0 < L ≤ 50
50 < L ≤ 100
100 < L ≤ 500
7
EDGE Swipe/Switch MFD to Control
Short press:
Enables edge swipe operation with the joystick.
• Opens the Layers menu.
thenthen
• Opens the Slide-out menu.
thenthen
Long press:
Switches MCU control to next configured MFD.
TOLERANCE (mm)
±1.5
±2.5
• Opens the Quick page.
• Opens the Data area.
±3
key
thenthen
thenthen
6 7
8 9
10 11
3
Event/GOTO
Short press:
• Creates an event mark at the
current position.
CURS/SCROLL
4
Switches joystick between cursor and screen scroll.
CANCEL/MOB
5
Short press:
• Goes back one layer in the menu.
• Closes the menu, dialogue box.
• End tool mode (route creation, etc.).
CTRL/Full Screen
6
Short press:
• Switches active window.
key
key
Long press:
• Place GOTO at the cursor location.
key
Long press:
• Inscribes an MOB mark at
current location.
key
Long press:
• Switches the active
screen between full screen,divided screen.
8
NAV INFO/F1
Short press:
• Show/hide the NAV INFO
window.
Gain/F2
9
Short press:
• Enables gain setting with the
Rotokey™ .
AUTO/STBY
10
Switches between AUTO and STBY mode for the connected
FURUNO AutoPilot.
Brill
11
• Opens the [Quick Access] window.
• Adjusts the brilliance when the [Quick Access] window is open.
Pub. No. E42-02210-A
(2404, TEHI) MCU-006/MCU-006H
key
key
key
key
Long press:
• Activate the function assigned
to two-finger short tap.
Long press:
• Activate the function assigned
to two-finger long tap.
00020031310
Loading...