Furuno GP-3300, GD-3300 User Manual

9-52 Ashihara-cho,9-52 Ashihara-cho,

*00080834300**00080834300*

*OME43920F00**OME43920F00*

Nishinomiya, JapanNishinomiya, Japan

Telephone :Telephone : 0798-65-21110798-65-2111 Telefax :Telefax : 0798-65-42000798-65-4200

Your Local Agent/DealerYour Local Agent/Dealer

ll rights reserved.

PUB.No.PUB.No. OME-43920OME-43920

(( YOSHYOSH ))

GD/GP-3300GD/GP-3300

Printed in JapanPrinted in Japan

FIRST EDITION :FIRST EDITION :AUG.AUG. 19981998

F :F : JUL.JUL. 22,200222,2002

* 0 0 0 8 0 8 3 4 3 0 0 ** 0 0 0 8 0 8 3 4 3 0 0 *

*OME43920F00**OME43920F00*

* O M E 4 3 9 2 0 F 0 0 ** O M E 4 3 9 2 0 F 0 0 *

SAFETY INSTRUCTIONS

WARNING

ELECTRICAL SHOCK HAZARD

Do not open the equipment.

Only qualified personnel should work inside the equipment.

Immediately turn off the power at the switchboard if water leaks into the equipment or something is dropped in the equipment.

Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service.

Do not disassemble or modify the equipment.

Fire, electrical shock or serious injury can result.

WARNING

Keep heater away from equipment.

A heater can melt the equipment’s power cord, which can cause fire or electrical shock.

Use the proper fuse.

Fuse rating is shown on the equipment. Use of a wrong fuse can result in equipment damage.

Do not place liquid-filled containers on the top of the equipment.

Fire or electrical shock can result if a liquid spills into the equipment.

Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire.

Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service.

Make sure no rain or water splash leaks into the equipment.

Fire or electrical shock can result if water leaks in the equipment.

iiiiiiiiiiiii

CAUTION

Do not use the equipment for other than its intended purpose.

Use of the equipment as a stepping stool, for example, can result in personal injury or equipment damage.

No one navigation device should ever be solely replied upon for the navigation of a vessel.

Always confirm position against all available aids to navigation, for safety of vessel and crew.

A warning label is attached to the equipment. Do not remove the label. If the label is missing or illegible, contact a FURUNO agent or dealer.

About the TFT LCD

The TFT LCD is constructed using the latest LCD techniques, and displays

99.99% of its pixels. The remaining 0.01% of the pixels may drop out or blink, however this is not an indication of malfunction.

WARNING

To avoid electrical shock, do not remove cover. No user-serviceable parts inside.

Name: Warning Label (1) Type: 86-003-1011-0 Code No.: 100-236-230

FOREWORD..........................................................................................................................vi

MENU TREE........................................................................................................................viii

SYSTEM CONFIGURATION........................................................................................ix

OPERATIONAL OVERVIEW

1.1 Control Description ...............................................................................................................1-1

1.2 Inserting Chart Cards.............................................................................................................1-2

1.3 Turning the Power On/Off .....................................................................................................1-3

1.4 The Trackball .........................................................................................................................1-4

1.5 The Cursor .............................................................................................................................1-4

1.6 Shifting the Display ...............................................................................................................1-5

1.7 Returning Own Ship Marker to Screen Center......................................................................1-5

1.8 Selecting Screen Center by Cursor Position..........................................................................1-6

1.9 Chart Scale.............................................................................................................................1-7

1.10 Display Brilliance and Key Backlighting............................................................................1-7

1.11 Card Drives, Chart Cards.....................................................................................................1-8

1.12 The Data Window..............................................................................................................1-12

1.13 Display Modes...................................................................................................................1-13

1.14 Menu Operation.................................................................................................................1-14

1.15 Operation on the Display...................................................................................................1-16

1.16 Operational Status Icons....................................................................................................1-17

1.17 Economy Mode .............................................................................................................. ...1-17

1.18 Plot Mode Displays ...........................................................................................................1-18

1.19 Setting the Time and Date .................................................................................................1-20

TRACK

2.1 Stopping Track Recording.....................................................................................................2-1

2.2 Track Color ............................................................................................................................2-2

2.3 Changing Color, Appearance of Specific Track ....................................................................2-2

2.4 Deleting Track .......................................................................................................................2-4

2.5 Track Plotting Interval ...........................................................................................................2-6

2.6 Customizing the Hold Function.............................................................................................2-8

2.7 Customizing the PLOT INTVL Key .....................................................................................2-9

MARKS, LINES

3.1 Entering Marks ......................................................................................................................3-1

3.2 Changing Current Mark Color...............................................................................................3-2

3.3 Changing Shape, Color of Specific Marks ............................................................................3-3

3.4 Deleting Marks ......................................................................................................................3-4

iii

3.5 External Event Mark..............................................................................................................3-5

3.6 Target Mark ...........................................................................................................................3-5

3.7 Lines ......................................................................................................................................3-5

WAYPOINTS

4.1 Entering Waypoints ...............................................................................................................4-2

4.2 Entering a Comment for a Waypoint .....................................................................................4-5

4.3 Turning Specific Waypoint Displays On/Off.........................................................................4-6

4.4 Deleting Waypoints ...............................................................................................................4-7

4.5 Destination Waypoint ............................................................................................................4-8

4.6 Cancelling Destination Waypoint ........................................................................................4-12

ROUTE NAVIGATION

5.1 Creating Routes .....................................................................................................................5-2

5.2 Following a Route .................................................................................................................5-5

5.3 Temporarily Deselecting a Route Waypoint ..........................................................................5-6

5.4 Deleting Route Waypoints .....................................................................................................5-7

5.5 Cancelling Route Navigation.................................................................................................5-8

5.6 Route Calculation ..................................................................................................................5-9

ALARMS

6.1 Arrival Alarm, Anchor W atch Alarm.....................................................................................6-1

6.2 XTE Alarm, Border Alarm ....................................................................................................6-3

6.3 Ship’s Speed Alarm ...............................................................................................................6-4

6.4 When the Alarm Buzzer Sounds............................................................................................6-5

VIDEO PILOT DISPLAY, NAVIGATION DATA DISPLAY

7.1 Video Pilot Display................................................................................................................7-1

7.2 Navigation Data Display .......................................................................................................7-4

AUTOPILOT DATA

8.1 Features Available with Autopilot Connection......................................................................8-1

8.2 Autopilot Information on Plot Display..................................................................................8-2

8.3 Autopilot Information on Video Pilot Display ......................................................................8-3

MEMORY CARD OPERATIONS

9.1 Formatting Memory Cards ....................................................................................................9-1

9.2 Saving Data to Memory Cards ..............................................................................................9-2

9.3 Playing Back Memory Cards.................................................................................................9-4

9.4 Saving, Playing Back Initial Settings ....................................................................................9-5

9.5 Editing Memory Cards ..........................................................................................................9-6

GPS RECEIVER OPERATION (GP-3300)

10.1 GPS Information on the Navigation Data Display ............................................................10-1

10.2 GPS and DGPS Initial Settings .........................................................................................10-3

10.3 Satellite Force Health/Deselection ....................................................................................10-5

10.4 GPS Smoothing .................................................................................................................10-6

10.5 Cold Start........................................................................................................................... 10-8

10.6 Geodetic Datum................................................................................................................. 10-9

10.7 Correcting GPS Position.................................................................................................... 10-9

OTHER FUNCTIONS

11.1 Displaying Position in Loran TDs .....................................................................................11-1

11.2 Bearing Display Reference................................................................................................ 11-2

11.3 Magnetic Deviation ...........................................................................................................11-3

11.4 Changing Chart Appearance .............................................................................................. 11-4

11.5 Correcting Chart Position .................................................................................................. 11-5

11.6 Loran TD Correction ......................................................................................................... 11-7

11.7 Calculating R/B Between Two Points ............................................................................... 11-8

11.8 Locking Preferred Settings .............................................................................................. 11-10

11.9 Memory Capacity ............................................................................................................11-10

11.10 Apportioning the Memory ............................................................................................. 11-12

11.11 Reading Number of Track, Marks Used ........................................................................ 11-13

11.12 Smoothing...................................................................................................................... 11-14

11.13 Selecting Navaid............................................................................................................ 11-15

11.14 Track, Mark and Marker Attributes ............................................................................... 11-16

11.15 Chart Symbols, Contour Lines Attributes...................................................................... 11-19

MAINTENANCE & TROUBLESHOOTING

12.1 Preventive Maintenance ....................................................................................................12-1

12.2 Diagnostic Tests.................................................................................................................12-2

12.3 Error Messages ..................................................................................................................12-5

12.4 Replacement of Fuse .........................................................................................................12-7

12.5 Replacement of Batteries...................................................................................................12-8

12.6 Verifying Program Version No. .........................................................................................12-9

12.7 Troubleshooting Table .....................................................................................................12-10

12.8 Clearing Memories .......................................................................................................... 12-12

APPENDIX

Time Differences ........................................................................................................................ A-1

Geodetic Chart List..................................................................................................................... A-2

SPECIFICATIONS......................................................................................................... SP-1

INDEX...............................................................................................................................Index-1

Declaration of Conformity

FOREWORD

A Word to FURUNO GD-3300/GP-3300 Owners

FURUNO Electric Company thanks you for considering and purchasing the FURUNO GD-3300/GP-3300. We are confident you will discover why FURUNO has become synonymous with quality and reliability.

For over 40 years FURUNO Electric Company has enjoyed an enviable reputation for efficient and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.

Y our unit is designed and manufactured to meet the rigorous demands of the marine environment. However, no machine can perform to the utmost of its ability unless properly operated and maintained. Please carefully read and follow the recommended procedures for operation and maintenance.

We would appreciate hearing from you, the end-user, about whether we are achieving our purposes.

Thank you for considering and purchasing FURUNO.

Features

The GD-3300 and the GP-3300 mostly share the same features. The GP-3300 is additionally equipped with a GPS receiver and a GPS antenna, to receive and process GPS satellite signals.

Navigation data appear on a high-resolution 10.4-inch color LCD. Data shown are shp’s position in latitude and longitude, speed and course, cursor position, range and bearing to cursor, range and bearing to a waypoint.

The display unit is powered by a 12 V or 24 VDC power supply.

• GP-3300 accepts connection of DGPS Beacon Receiver

• NAVIONICS chart card compatible

• Alarms: Arrival alarm, Anchor Watch alarm, Cross-track Error alarm, Border alarm, Ship’s Speed alarm

• Large capacity memory: 8,000 points of tracks and marks, 98 waypoints, 10 routes with 15 waypoints per route

• Comprehensive navigation display of alphanumeric navigation data plus automatic track plotting

• Economy mode reduces power consumption – LCD is turned off while receiver/processor keeps updating data.

• Factory-digitized electronic charts on ROM cards.

• Memory cards for storage of track, waypoints, marks

• Menu-driven operation

• Navigation planning from/to waypoint or route

vii

MENU TREE

1 WAYPOINT

2 ROUTE

3 SAVE DATA TO MEMORY CARD

1 TRACK 2 MARK/LINE 3 WAYPOINT/ROUTE 4 INITIAL SETTINGS

7 DELETE MEMORY CARD DATA 8 FORMAT MEMORY CARD 9 SELECT CARD SLOT

( 1 UPPER 2 LOWER)

4 LOAD MEMORY CARD

1 TRACK 2 MARK/LINE 3 WAYPOINT/ROUTE 4 INITIAL SETTINGS

9 SELECT CARD SLOT

( 1 UPPER 2 LOWER)

5 DISPLAY MEMORY CARD

6 CORRECT POSITION

7 APPORTION/DELETE MEMORY

1 APPORTION MEMORY 2 DELETE TRACK 3 DELETE MARK

8 INITIAL SETTINGS (See below.)

9 MISC

1 EDIT TRACK/MARK

CALCULATE

RANGE/BEARING

6 SPECIAL

SELECT MARKS/

CONTOUR LINE

CLEAR

MEMORY

CLEAR SCREEN

DATA CLEAR ALL GD

DATA CLEAR GPS

DATA

4 CLEAR ALL DATA

INITIAL SETTINGS, page 1

INTERNAL NAV EXTERNAL NAV I/O DATA FORMAT L/L SMOOTHING PLOT INTERVAL 1 PLOT INTERVAL 2 WAYPOINT MARK EVENT MARK TRACK(HOLD PLOT) LINE (HOLD PLOT) MAGNETIC DEVIATION BEARING COURSE VECTOR MARK SIZE CURSOR SIZE OWN SHIP MARK TRACK WIDTH RANGE UNIT VTD AVG TIME DATE TIME EXTERNAL CLOCK AUTOPILOT DISPLAY TD INDICATION

INITIAL SETTINGS, page 2 (GPS settings)

POSITION FIXING MODE GEODETIC DATUM HDOP THRESHOLD TIME DIFFERENCE LATITUDE LONGITUDE DELTA LATITUDE DELTA LONGITUDE SMOOTHING ANTENNA HEIGHT COLD START CST SATELLITE NO. MIN. ELEVATION ANGLE DESELECT SAT NO. D.GPS MODE RTCM VER BYTE FORM FIRST BIT PARITY BIT STOP BIT BIT RATE BAUD RATES

viii

9 SELF TEST

MEMORY • I/O

PORT

2 KEYBOARD

TEST

PATTERN 1 TEST

PATTERN 2

GPS ANTENNA UNIT GPA-017S (For GP-3300)

Differential GPS Receiver GR-80* (GP-3300 only)

SYSTEM CONFIGURATION

GPS PLOTTER

MODE

NAV

VIDEO

MANU

PLOT

DATA

PILOT

SELECT

FR/TO WPT

ROUTE ALARM

MARK

PLOT

TRACK

CHART

COLOR

INTVL

COLOR

EVENT

L R

CURSOR ON/OFF

BRILL

ECONO

6325874

ZOOMINZOOM

CEN TER

E N T

OUT

Navigator (for GD-3300) Video Sounder Radar Autopilot Event Switch

POWER

OFF

Rectifier

PR-62

100/110/220/230 VAC 50/60 Hz

SHIP’S MAINS

10.8 - 31.2 VDC

DISPLAY UNIT GP-3300-E/ GD-3300-E

: Option : Connectable external equipment

* Cannot be connected to GD-3300.

OPERATIONAL OVERVIEW

This chapter acquaints you with the basics of your unit – from turning on the power to entering the time and date.

1.1 Control Description

The keyboard consists of 40 logically arranged keys. The unit confirms correct key input by releasing a single beep. Invalid key input is denoted by a series of beeps.

GPS PLOTTER

VIDEO

PLOT

PILOT

SELECT

FR/TO WPT

TRACK

CHART

COLOR

ZOOMINZOOM

CURSOR ON/OFF

BRILL

ECONO

MODE

DATA

ROUTE ALARM

PLOT INTVL

CEN TER

NAV

MANU

MARK COLOR

EVENT

C L R

6325874

E N T

OUT

Keyboard

POWER

OFF

Power switch

Figure 1-1 Display unit

Trackball

Card slot Memory card (upper) Electronic chart card (lower)

1-1

lortnoC/yeKnoitcnuF

TOLP .syalpsidatadffo/nonrutotsnoitcnufoslA.yalpsidtolpstceleS

TOLIPOEDIV .syalpsidatadffo/nonrutotsnoitcnufoslA.yalpsidtolipoedivstceleS

ATADVAN.yalpsidatadnoitagivanstceleS UNEM .neercssuoiverpsyalpsid;unemsesolc/snepO OT/RF.tniopyawnoitanitsedslecnac/steS

TPW.stniopyawsretsigeR

ETUOR.setuorsretsigeR

MRALA.unemmralasyalpsiD

TRAHC .trahccinortceledezitigid-yrotcaffosetubirttasegnahC

ROLOCKCART.rolockcartsegnahC

LVTNITOLP .kcartgnidrocerspotsrolavretnitolpastcelessserphcaE

ROLOCKRAM.rolockramsegnahC

TNEVEdnasyeKKRAM nehwrotagivanotnoitisops’pihsstuptuO:TNEVE(.enil/kramsretnE

syeKciremuN.atadciremunretnE

RLC secnelis;tniopyawrokramseteled;atadfoenileritnenasraelC

TNE.tupnidraobyeksetanimreT

]+[ tniopyawnosnrut;tsaErohtroNotetanidroocedutitalsegnahC

]-[ tniopyawffosnrut;tseWrohtuoSotetanidroocedutignolsegnahC

FFO/NOROSRUC.ffo/norosrucsnruT

NIMOOZ

TUOMOOZ

RETNEC .retnecneercsotrosruc/rekrampihsnwosnruteR

syeKworrA.rosrucdnayalpsidtfihS

ONOCELLIRB otsnoitcnufoslA.gnithgilkcabdraobyekdnaecnaillirbneercsstsujdA

T able 1-1 Control description

).desserp

.mralaelbidua

.stniopetuorstceles;yalpsid

.stniopetuorstcelesed;yalpsid

.elacstrahcegnahC

.egapsllorcs;)sDTnaroLroL/L(dohtemnoitacidninoitisopsegnahC

:etoN ".yekegnahC"sasyalpsidunemnosraeppayeksihT

DCLehtlitnunwoddlohdnasserp(edomymonoceehtffo/nonrut

.)ffosnrut

1.2 Inserting Chart Cards

Normally, insert appropriate chart card before turning on the power.

1. Open the card drive cover.

Figure 1-2 Opening chart slot

1-2

2. Insert the electronic chart card which contains a chart of your sea area into the lower card drive.

Figure 1-3 Inserting chart card

Note: Always close the card drive cover to keep humidity and water out of the drive.

1.3 Turning the Power On/Off

Turning the power on

Press the [POWER] switch at bottom left-hand side of the unit. You will hear a “peep” when turning on the power. To turn off the power press the switch again.

After turning on the power the display changes in the sequence illustrated in Figure 1-4. About 20 seconds later accurate own ship’ s position is displayed in case of the GP-3300.

GPS PLOTTER

POWER

OFF

Power switch

CHART

CURSOR

ECONO

PLOT

FR/TO WPT

ON/OFF

BRILL

MODE

NAV

VIDEO

DATA

PILOT

SELECT

ROUTE ALARM

PLOT

TRACK

INTVL

COLOR

6325874

ZOOMINZOOM

CEN TER

MANU

MARK COLOR

EVENT

C L R

E N T

OUT

Figure 1-4 GD-3300/GP-3300

For the GP-3300, at the first power application after installation, it takes about two minutes to acquire GPS satellite data, called the almanac. While the unit is acquiring the almanac, the indication “CST” appears at the top of the display . “CST” is replaced by “2D” or “ACQ” after the almanac is acquired. If the vessel has moved more than 600 miles with the system turned off, reenter estimated position on the

GPS INITIAL SETTINGS menu (key sequence: [MENU], [8], [

]).

If asterisks appear instead of ship’s position data, this means there is no navigation input. Check to make sure proper navigation aid is selected on the INITIAL SETTINGS menu (keying sequence: [MENU], [8]).

1-3

1.4 The Trackball

1.5 The Cursor

The main function of the trackball is to shift the cursor and the display. The display may be shifted when the cursor is turned off; the cursor when it is turned on.

Figure 1-5 Operating the trackball, shifting the picture (cursor off)

The cursor functions to

• Find latitude and longitude of a location

• Find range and bearing from your ship to position selected

• Enter and erase marks, lines and waypoints Note: Y ou can select cursor configuration (cross hairs or entire screen

cursor) on the INITIAL SETTINGS menu (keying sequence: [MENU], [8]). The default cursor configuration is the cross hairs.

Turning the cursor on/off

Each press of the [CURSOR ON/OFF] key turns the cursor on/off. With the cursor on, operate the trackball or the arrow keys to shift the

cursor. Use the trackball for general placement and the arrow keys for fine tuning. The cursor moves in the direction of the trackball moves. When the cursor reaches the edge of the display, the display shifts in the opposite direction.

1-4

Figure 1-6 Shifting the cursor

Cursor information

Cursor position in latitude and longitude and the range and bearing from your ship to the cursor appear in the data window at the top of the display.

Cursor position

+36° 44.257’ N 340.5° 134° 40.719’ E 10.0KTS

Figure 1-7 Location of cursor information

1.6 Shifting the Display

The display can be shifted, when the cursor is off, by the trackball or arrow keys. The display shifts in the direction of trackball rotation or arrow key pressed. Note that this function is only available with FURUNO chart cards.

40 42

Cursor

1.46NM

109.8

0.10NM

2D 1.2

Cursor range Cursor bearing

1.7 Returning Own Ship Marker to Screen Center

You can return the own ship marker to the screen center by pressing the [CENTER] key. This function is only available with FURUNO chart cards.

1-5

1.8 Selecting Screen Center by Cursor Position

In normal usage your ship is at the screen center. This function is only available with FURUNO chart cards.

If you want to select a land feature as the screen center, do the following:

1. Display the cursor (if it is not already displayed) by pressing the [CURSOR ON/OFF] key.

2. Operate the trackball to place cursor on position desired.

3. Press the [CENTER] key.

CENTER

Figure 1-8 How to select screen center

1-6

1.9 Chart Scale

The chart scale can be adjusted with the [ZOOM IN] and [ZOOM OUT] keys. Note that the [ZOOM IN] key shrinks the picture, and the [ZOOM OUT] key “blows up” the picture. With a smaller range, you may find that the track appears in tiers.

The horizontal range of the display in nautical miles appears at the top right-hand corner of the Data Display. Whenever the scale is changed the new range appears momentarily at the screen center.

Horizontal range (123.4 NM)

DATA DISPLAY (2)

34° 44.258’ N 340.5° 123.4NM

0’ 10"

134° 40.719’ E 341.2°

123.4NM

Figure 1-9 Location of chart scale indications

GPS 1.2

Horizontal range

1.10 Display Brilliance and Key Backlighting

The [BRILL ECONO] key adjusts display screen brilliance and keyboard backlighting in seven levels including off.

1-7

1.1 1 Card Drives, Chart Cards

Card drives

Two card drives are behind the card drive door: t he upper slot is for memory cards which store display data (waypoints, tracks, and marks), and the lower slot is for digitized chart cards.

Displaying an electronic chart with the power turned on

Follow the procedure below to display an electronic chart with the power turned on.

1. Open the card slot door.

Figure 1-10 Opening card slot door

2. Insert chart card label side up in the lower slot.

This side up.

FURUNO Card

Figure 1-11 Inserting chart card

3. Close the card slot door.

4. Press [ZOOM IN] or [ZOOM OUT] key to display chart.

NAVIONICS Card

1-8

Ejecting the chart card

Press the eject button.

Figure 1-12 Removing chart card

Care and handling of the cards

• Keep the cards away from direct sunlight, heat sources, and active

gases.

• Keep cards away from water and chemicals.

• Keep the connector free of foreign material.

• Do not drop the cards.

Chart card troubleshooting

• Chart does not disappear after removing card.

Operate [ZOOM IN] or [ZOOM OUT] key.

• Card inserted but chart does not appear.

Operate [ZOOM IN] and [ZOOM OUT] keys.

• Small island or object is not filled in (it is hollow).

Operate [ZOOM IN] and [ZOOM OUT] keys.

• Part of land on video pilot display is hollow.

Shift display.

• Land areas on a chart are hollow.

Chart overenlarged. Operate [ZOOM IN] key.

1-9

Chart icons

The display shows three different icons to alert the operator to chart status. These are as described in Table 1-2.

Table 1-2 Chart icons

Icon Reason Displayed Remedy

• Card is not inserted properly.

• Chart scale is too small.

• This icon means the chart is displayed properly; full chart reliability.

• This icon means poor chart reliability because chart is overenlarged.

• Insert card.

• Enlarge chart by [ZOOM IN] key.

Use chart with extreme caution. Shrink chart by [ZOOM OUT] key.

FURUNO chart symbols

The table below shows FURUNO chart symbols and their meanings.

Table 1-3 FURUNO chart symbols

Symbol

Description Symbol

Description

Summit

Wreck

Lighthouse

Lighted Buoy

Buoy

Radio Station

Position of Sounding

Obstruction

Fishing Reef

Platform

Anchorage

1-10

Comparison of FURUNO, NAVIONICS chart cards

Table 1-4 Comparison of FURUNO, NAVIONICS chart cards

metIONURUFSCINOIVAN

gnillorcstoD

ytilibapac

yalpsidpu-esruoCSEYON

youb,esuohthgiL

noitatneserpatad

rosructamooZ

noitisop

rotauqEtaegnaR,6,4,3,2,5.1,1

gniretneCSEY2*

:2*.yltcefrepderetnecebtonyamnoitisoppihsnwoehT

SEYON

ONSEY

SEY1*

mn2918...21,8

yrtneatadtesffotrahCSEYON

.deretnecebtonyamrosrucehT:1*

nacstod652ylno(

)ecnotadellorcseb

,1,5.0,52.0,521.0

mn4201...8,4,2

Buoy, lighthouse data display on NAVIONICS charts

NAVIONICS chart cards can show buoy and lighthouse data.

1. Insert a NA VIONICS chart card in the lower slot. Buoys and lighthouses are shown on the chart as in the figure below.

Lighthouse

Buoy

Figure 1-13 Appearance of lighthouse and buoy on Navionics chart

2. Place the cursor on a buoy or lighthouse mark to display data about that mark.

FL 12S 27M

Buoy, lighthouse data

Place the cursor on a buoy or lighthouse mark.

Figure 1-14 Buoy, lighthouse data

1-11

FL (2) 12S 15M

FL : Flashing F : Fixed light F FL : Fixed and Flashing light MO : Morse code light Oc : Occulting light

Figure 1-15 How to interpret buoy, lighthouse data

1.12 The Data Window

The data window at the top of the display shows various navigation information. What information is displayed depends on whether the cursor is on or off and the status of the [PLOT] key or [VIDEO PILOT] key . Figures 1-16 and 1-17 show what appears in the data window under those conditions.

Visibility in nautical miles (Example: 15 miles)

Period in seconds (Example: 12 seconds)

Number of flashes (Example: 2)

Data shown when cursor is on

DATA DISPLAY (1)

+ CURSOR LAT HEADING

CURSOR LON SPEED

DATA DISPLAY (2)

+ CURSOR LAT CURSOR BEARING CHART SCALE

CURSOR LON SHIP'S HEADING

Figure 1-16 Information displayed in data window when cursor is on

RANGE TO CURSOR BEARING TO CURSOR PLOTTING INTERVAL NAVIGATOR/HDOP

PLOT

PLOTING INTERVAL NAVIGATOR/HDOP

PLOT

NO DISPLAY

PLOT

1-12

Data shown when cursor is off

DATA DISPLAY (2)

Figure 1-17 Information displayed in data window when cursor is off

1.13 Display Modes

Your plotter has three display modes: Plot, Video Pilot, and Navigation Data. You may select those modes with the [PLOT], [VIDEO PILOT], and [NAV DATA] keys, respectively.

DATA DISPLAY (1)

YOUR SHIP LAT HEADING YOUR SHIP LON SPEED

YOUR SHIP LAT BEARING TO CHART SCALE

YOUR SHIP LON HEADING

DESTINATION

RANGE TO DESTINATION BEARING TO DESTINATION PLOTTING INTERVAL NAVIGATOR/HDOP

PLOT

PLOTTING INTERVAL NAVIGATOR/HDOP

NO. DATA WHEN DESTINATION WAYPOINT NOT SELECTED

PLOT

NO DISPLAY

PLOT

Plot mode description

This mode provides general positioning information and shows

• latitude and longitude grid

• own ship mark

• factory-digitized chart

• ship’s track

• marks, and

• waypoints.

Video pilot mode description

The video pilot mode provides ship piloting information and features the following.

• Own ship mark is triangle shaped and shows bow bearing.

• Grid shows distance in nautical miles from own ship.

• Course up display

• ETA and TTG to waypoint

Nav data mode description

This display shows navigation data such as

• Speed

• Course

• Data from external sensors (water temperature, depth, etc.)

• Position, and

• GPS satellite information (GP-3300 only).

1-13

1.14 Menu Operation

Menu operation versus key operation

Many functions of your plotter can be executed through the menu or by pressing the key associated with function desired. For example, you can enter a waypoint by pressing the [WPT] key , or [MENU] and [1].

T o display the menu, press the [MENU] key to display the Main menu. To select a menu, press appropriate numeric key.

MENU 1 WAYPOINT 2 ROUTE 3 SAVE DATA TO MEMORY CARD 4 LOAD MEMORY CARD 5 DISPLAY MEMORY CARD 6 CORRECT POSITION 7 APPORTION/DELETE MEMORY 8 INITIAL SETTINGS 9 MISC SELECT BY USING NUMBER KEY.

Figure 1-18 Main menu

1-14

Main menu description

Table 1-5 Main menu description

uneM

.oN

1TNIOPYAW ,tniopyawseteled/stide;edutignoldnaedutitalybtniopyawsretsigeR

2ETUOR.tsiletuorsyalpsiD 3OTATADEVAS

4YROMEMDAOL

5YROMEMYALPSID

6NOITISOPTCERROC.rorrenoitisoptrahcstcerroC 7ETELED/NOITROPPA

8SGNITTESLAITINI.unemSGNITTESLAITINIsyalpsiD 9CSIM.skram/kcarteteled,tidE:KRAM/KCARTTIDE.1

uneMnoitcnuF

DRACYROMEM

DRAC

YROMEM

.tsiltniopyawsyalpsid

.dracyromemottnenopmocyalpsidderisedsevaS

.kcartevaS:KCART.1

.senil/skramevaS:ENIL/KRAM.2

.etuor/tniopyawevaS:ETUOR/TNIOPYAW.3

.sgnitteslaitinievaS:SGNITTESLAITINI.4

.dracyromemnoelifeteleD:ATADDRACYROMEMETELED.7

.8.metsyshtiwesurofdracyromemeraperP:DRACYROMEMTAMROF

.esuottolsdracyromemtceleS:TOLSDRACTCELES.9

.dracyromemsdaoL

.kcartsdaoL:KCART.1

.senil/skramsdaoL:ENIL/KRAM.2

.setuor/stniopyawsdaoL:ETUOR/TNIOPYAW.3

.sgnitteslaitinidaoL:SGNITTESLAITINI.4

.esuottolsdracyromemstceleS:TOLSDRACTCELES.9 ).deraelctonsiyalpsidtahtetoN(.dracyromemkcabsyalP

.yromemseteledsnoitroppA

.1.skramdnakcartneewtebyromemsnoitroppA:YROMEMNOITROPPA

.stniop000,8sikcartdnaskramrofyticapaclatoT

.kcartllaseteleD:KCARTETELED.2

.skramllaseteleD:KRAMETELED.3

gniraebdnaegnarsetaluclaC:GNIRAEB/EGNARETALUCLAC.2

neewteb.stniopowt

LAICEPS.6

.fforonokramemitsnruT:KRAMEMIT)1

nowodniwnoitamofnikramsnruT:WODNIWKRAMTNEVE)2

.ffo/noyalpsidtolipoediv

.stniopyawetuorstcennocsid/stcennoC:ENILETUOR)3

.elacsroecnatsidrofelacstrahcstceleS:ELACSNEERCS)4

.tamrofatadtolipotuastceleS:TAMROFATADPA)5

skramtrahcforolocstceleS:ENILRUOTNOC/SKRAMTCELES.7

.ffo/nomehtnrutdnasenilsruotnocdna

YROMEMRAELC.8

.yalpsidtnerrucsraelC:ATADNEERCSRAELC)1

.atadDGsraelC:ATADDGLLARAELC)2

.)ylno0033-PG(atadreviecerSPGsraelC:ATADSPGRAELC)3

.)ylno

0033-PG(atadSPGdnaDGhtobsraelC:ATADLLARAELC)4

.)ylno

TSETFLES.9

.stropO/IdnaseiromemskcehC:TROPO/I/YROMEM)1

.draobyekstseT:DRAOBYEK)2

.tuopordrolocrofstseT:1NRETTAPTSET)3

.noitrotsedrolocrofstseT:2NRETTAPTSET)4

1-15

1.15 Operation on the Display

Selecting items

As you move the item selection cursor (red triangle) down through a menu by pressing [↑]/[↓], the ored in light-blue, changes to red. This indicates current selection for line selected.

Selecting options

To select options;

1. Press [↑]/[↓] to place the item selection cursor on the item you

want to change.

2. Press [←]/[→] to place the option selection cursor on the option

desired.

Entering data

option selection cursor, initially col-

The reverse video “square” on the display is the data input cursor. Press [←]/[→] to locate the cursor where you want to enter data, and then enter appropriate data with the numeric keys. The entry of the leading zero is necessary, but the entry of trailing zeroes is optional. For example, if you want to enter 7, press [0] and [7].

Summary of menu operation

Figure 1-19 shows how to select items and options on the DESTINATION SETTING menu, which appears by pressing the [FR/TO] key.

DATA INPUT CURSOR This cursor selects location to enter data.

OPTION SELECTION CURSOR This cursor, which moves by and , shows current selection.

DESTINATION SETTING

DEST = SET CANCEL MODE = CURSOR WAYPOINT ROUTE R/B WPT NO. = 0 0 + _ _ + _ _ + _ _ + _ _ + _ _ + _ _

+ _ _ + _ _ + _ _ + _ _ + _ _ + _ _ + _ _

1-16

ITEM SELECTION CURSOR This cursor, which moves by and , selects line to select or enter data.

Figure 1-19 DESTINATION SETTING menu

ENTER WAYPOINT NO.

This box provides abbreviated instructions.

1.16 Operational Status Icons

Various icons at the bottom right-hand corner of the display to alert the operator to operational status. T able 1-6 explains the meanings of these icons.

Table 1-6 Operational status icons

.elbaileratadtrahCatadtrahc;degralnerevotrahC

.elbailernuebyam

kcart(ffodenrutgnidrocerkcarT

.)dloh

sraeppasidnocI.noitaloivmralA

rodegagnesidsimralanehw

.devomersimralafoesuac

.trahc

.ecneinevnoc

gnorwrodegralnerevotrahC

dracyromemfoegatlovwoL

;draoBCDGnoyrettabroyrettab

tseilraetayrettabecalper

nodeilppatesffonoitisoptrahC

.unemNOITISOPTCERROC

.)ylno0033-PG(

nodeilppatesffonoitisopL/L

unemSGNITTESLAITINISPG

1.17 Economy Mode

The economy mode turns off the LCD to lessen power consumption (GD-3300: 13 W → 6W, GP-3300: 15 W → 8W). The track is continually recorded and plotted. To turn the economy mode on press and hold down the [BRILL ECONO] key about three seconds. The lamp on the key lights when the economy mode is on. T o turn off the economy mode, press the key again.

1-17

1.18 Plot Mode Displays

Information displayed on the plot display depends on whether the cursor is on or off. Figures 1-20 and 1-21 show sample plot displays with the cursor on and off, respectively.

Plot display when cursor is on

Cursor bearing

Mark cursor

Cursor latitude

Cursor longitude

+36° 44.257’ N 140.50° 35.92NM

0.10NM

134° 40.719’ E 50.5°

Heading

PLOT

Heading

+36° 44.257’ N 50.5° 134° 40.719’ E 10.0KTS

40 42

MARK

WAYPOINT

MARK

OWN SHIP MARK

2D 1.1

140.50 2D 1.1

COURSE VECTOR

DESINATION WAYPOINT (SELECTED BY

CURSOR) IDEAL COURSE TO DESTINATION

MARK

Ship’s speed

1.46NM

0.10NM

Horizontal range Plotting interval

Navigator/HDOP

Cursor range Cursor bearing Plotting interval Navigator/HDOP

Target data from radar

1-18

CURSOR

PLUS MARK

TRACK

MARK

WAYPOINT

LINE

Figure 1-20 Plot display, cursor on

Icon

Plot display when cursor is off

Bearing to destination

Mark cursor

Ship’s latitude

Ship’s longitude

36° 44.257’ N 59.8° 35.92NM

0.10NM

134° 40.719’ E 50.5°

Heading

PLOT

Heading

36° 44.257’ N 50.5° 134° 40.719’ E 10.0KTS

40 42

MARK

WAYPOINT

MARK

OWN SHIP MARK

GPS 1.2

59.8 2D 1.2

COURSE VECTOR

DESINATION WAYPOINT (SELECTED BY

CURSOR) IDEAL COURSE TO DESTINATION

MARK

Ship’s speed

1.46NM

0.10NM

Horizontal range Plotting interval

Navigator/HDOP

Range to destination* Bearing to destination* Plotting interval Navigator/HDOP

*: No waypoint data

when destination waypoint is not

selected.

CURSOR

PLUS MARK

TRACK

MARK

WAYPOINT

LINE

Figure 1-21 Plot display, cursor off

1-19

+ 107 hidden pages

Furuno GP-3300, GD-3300 User Manual

SAFETY INSTRUCTIONS

TABLE OF CONTENTS

FOREWORD

MENU TREE

SYSTEM CONFIGURATION

OPERATIONAL OVERVIEW

1.1 Control Description

1.2 Inserting Chart Cards

1.3 Turning the Power On/Off

1.4 The Trackball

1.5 The Cursor

1.6 Shifting the Display

1.7 Returning Own Ship Marker to Screen Center

1.8 Selecting Screen Center by Cursor Position

1.9 Chart Scale

1.10 Display Brilliance and Key Backlighting

1.1 1 Card Drives, Chart Cards

1.12 The Data Window

1.13 Display Modes

1.14 Menu Operation

1.15 Operation on the Display

1.16 Operational Status Icons

1.17 Economy Mode

1.18 Plot Mode Displays