Furuno GP-30 User Manual
X
X
GP-30/35 GPS NAVIGATOR
Operator's Guide
The purpose of this operator's guide is to provide the basic operating procedures for this
equipment. For detailed information, refer to the operator's manual.
Selecting Display Mode
Press the [DISP] key.
Plotter Display
2D
n
[ 5 ]
m
CSE:
7°
SPD:
k
0.0
t
34°44.000N 135°21.000E
x
X
Highway Display
---°
BRG
7°
CSE
RNG
SPD
---
6.5
n
m
k
t
0.5
XTE:
N
0.5
0.05
Steering Display
2D MAG
300 330
NE
k
6.5
SPD:
RNG:
TTG:
Nav Data Display
t
n
--.-
m
1H30M 12:30
30 60
CSE:
BRG:
ETA:
05:32
20°
---°
n
m
Ship's track and
data
3D view of ship's
track overlaid on
intended course
Graphic display
of steering data
Enlarging, Shrinking the Display
1. Press the [MENU] key.
2. Press the [ENT] key.
3. Press ▲ to enlarge; ▼ to shrink.
4. Press the [ENT] key to close the window .
Shifting the Cursor, Display
1. Press the Cursor Pad to turn on and shift
the cursor.
2. Place the cursor on an edge of the screen
to shift the display.
Centering Own Position
1. Press the [MENU] key.
2. Select “SHIP TO CENTER?”.
3. Press the [ENT] key.
Entering MOB Mark
1. Press the [MARK/MOB] key.
2. Select “MOB?”.
3. Press the [ENT] key.
4. Press the [ENT] key again.
2D
12–DEC–97 15:37:40
34° 44. 000'
135° 21. 000'
kt
SPD:
CSE:
N
E
7°6.5
Comprehensive
navigation data
display
Registering Waypoints
Setting, Cancelling Destination
A waypoint can be entered four ways. Below is the procedure for entry by the cursor .
1. Operate the Cursor Pad to place the cursor on the location you want to make a
waypoint.
2. Press the [ENT] key.
CURSOR POS. → WYPT
ENTER A NEW WYPT NAME.
0 0 1 — — — ?
( 001: DEFAULT NAME )
Quit : [MENU]
3. Press the [ENT] key.
NAME: KOBE
34°44.000’N MARK
135°21.000’E x
12—DEC—97 11:25
Exit?
4. Place the cursor under “MARK”.
5. Press the [ENT] key.
6. Press ▲ or ▼ to select the mark desired.
7. Press the [ENT] key.
8. Select “Exit?” and then press the [ENT]
key.
Destination can be set three ways. Below is
the method for setting destination by the
cursor.
To set destination;
1. Press the [GOTO] key.
2. Select “CURSOR?”.
3. Press the [ENT] key.
4. Place the cursor on position to set as destination.
5. Press the [ENT] key.
To cancel destination;
1. Press the [GOTO] key.
2. Select “OFF?”.
3. Press the [ENT] key.
Setting the Arrival Alarm
1. Press the [MENU] key twice.
2. Select “ALARMS”.
3. Press the [ENT] key.
4. Press the [ENT] key.
5. Select “ARV”.
6. Press the [ENT] key.
7. Press the [ENT] key and enter arrival
alarm range.
8. Press the [ENT] key.
9. Press the [MENU] key.
Registering Routes
1. Press the [MENU] key twice.
2. Select “ROUTES”.
3. Press the [ENT] key.
4. Press the [ENT] key.
5. Press the [ENT] key, select route
waypoint and press the [ENT] key.
6. Repeat steps 5 to enter other waypoints
on the route.
7. Select “Exit?”.
8. Press the [ENT] key to register.
(9801,DAMI) GP-30/35
PUB.NO.OSE-43840-D
Loading...