FUNAI FDRV90E User Manual

Owner's Manual
Owner’s Manual
DVD Recorder with Video Cassette Recorder
FDRV-90E
Before you start Connections
Getting started
POWER
Supplied Accessory
• Remote control (NA817UD) with two AA batteries
OPEN/CLOSE
STOP/EJECT
REW F.FWD RECORD
PLAY
CHANNEL
VCR Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation.The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.
DUBBING
SELECT
VCR
VCR
INSTRUCCIONES EN ESPAÑOL INCLUIDAS
INSTRUCTIONS EN FRANÇAIS INCLUSES
• RF cable WPZ
0901TM002)
(
• Audio/Video cables (WPZ0102TM015 or
WPZ0102LTE01)
• Owner’s Manual (1VMN20226)
STOP PLAY RECORD
DVD
DVD
S-VIDEO
VIDEO L - AUDIO - R
• Quick Use Guide (1VMN20295)
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
If you need additional operating assistance after reading this owner’s manual or to
order replacement accessories, please call
TOLL FREE : 1-800-605-8453
or visit our web site at http://www.funai.us
Before you use this unit , you need to complete connections. Refer to “Connections” on pages 13-15.
To r ecord a program easily, refer to “Easy DVD recording” on pages 16-17 after connections are completed.
(You CANNOT record on any copyright protected DVD disc with this unit.)
Others
Español
Français
Before you start
Precautions
WARNING
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
:
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI-
ANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilat­eral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclo­sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intend­ed to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM. LOCATION: INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly approved in the instruc­tion manual.The user could lose the authority to operate this equipment if an unauthorized change or modi­fication is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installa­tion.This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recy­cling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details.
For Customer Use: Read carefully the information located at the back of this unit and enter below the Serial No.Retain this information for future refer­ence.
Model No. Serial No. _____________________
_____________________
2
Before you start
Precautions (cont’d)
Important Safeguards
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the oper­ating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION:A product that is meant for uninterrupted ser­vice and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter,is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7.Water and Moisture- Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool,and the like.
8.Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table.The product may fall,causing seri­ous injury to a child or adult, and serious damage to the appli­ance. Use only with a cart, stand, tripod, bracket, or table rec­ommended by the manufacturer, or sold with the product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufac­turer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
9.Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating,and these openings must not be blocked or covered.The openings should never be blocked by placing the product on a bed, sofa, rug,or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home,consult your appliance dealer or local power company. For products intend­ed to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way.This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polar­ized plug.
12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them,paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.Article 810 of the National Electrical Code,ANSI/NFPA No.70, provides infor­mation with regard to proper grounding of the mast and sup-
porting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of anten­na-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig.A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
S2898A
ANTENNA LEAD WIRE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
14. Lightning - For added protection for this product during a light­ning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits,or where it can fall into such power lines or cir­cuits.When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or cir­cuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind into this product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
18. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous volt­age or other hazards. Refer all servicing to qualified service per­sonnel.
19. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the oper-
ating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e.If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in performance this
indicates a need for service.
20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, elec­tric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
22. Heat - This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Before you start
Connections
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
3
Before you start
Precautions (cont’d)
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibra­tion or strong magnetic fields.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.
• If by accident water is spilled on this unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing.
• Do not put your fingers or objects into the unit cassette holder.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use this unit at least for 2 hours until its inside gets dry.
About Copyright
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technolo­gy that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise autho­rized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Notice for progressive scan outputs
Consumers should note that not all high definition televi­sion sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard defin­ition’ output. If there are questions regarding our TV set compatibility with this model 525p DVD recorder, please contact our customer service center.
Symbol in this owner's manual
Many functions of this unit are depending on the disc type or the recording mode. To specify for what disc type or recording mode each function is, we put the following symbols at the beginning of each item to operate.
4
Symbol
DVD-V
DVD-V
DVD-RW
DVD-RW
DVD-RW
DVD-RW
DVD-R
DVD-R
CD
CD
MP3
MP3
VCR
VCR
First: (Press:)
First: (Press:)
Video
VR
Description
Available to DVD Video discs
Available to DVD-RW in Video mode
Available to DVD-RW in VR mode
Available to DVD-R discs
Available to Audio CDs
Available to CD-R/RW discs with MP3 files
Available to VHS tapes Use only cassettes marked .
Indicates that you need to select the DVD
DVD
mode by pressing DVD button on the remote control before proceeding next step.
Indicates that you need to select the VCR
VCR
mode by pressing VCR button on the remote control before proceeding next step.
Maintenance
SERVICING
• Please refer to relevant topics on the Troubleshooting Guide on pages 101-104 before returning the product.
• If this unit becomes inoperative, do not try to correct the problem by yourself.There are no user-serviceable parts inside.Turn off, unplug the power plug, and please call our help line mentioned on the front page to locate an Authorized Service Center.
CLEANING THE CABINET
Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.
CLEANING DISCS
• When a disc becomes dirty, clean it with a cleaning cloth.Wipe the disc from the center out. Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commer­cially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.
CLEANING THE DISC LENS
If this unit still does not perform properly although you refer to the relevant sections and to “TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
Always store the disc in its protective case when it is not used.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulat­ed on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in the unit may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line mentioned on the front page to locate an Authorized Service Center.
NOTES:
• Remember to read the instructions along with the video head cleaner before use.
• Clean video heads only when problems occur.
Before you start
Ta b le of contents
Before you start . . . . . . . . . . . . . . . . . . .2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Ta b le of contents . . . . . . . . . . . . . . . . . . . . . . . . . .5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Functional overview . . . . . . . . . . . . . . . . . . . . . . .7
Installing batteries in the remote control . . . . . . . . . .9
Using a remote control . . . . . . . . . . . . . . . . . . . . . . .9
VCR/DVD recorder Switching . . . . . . . . . . . . . . . . . .9
SETUP/DISC/CD menu . . . . . . . . . . . . . . . . . . . . . . .10
DISPLAY menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connections . . . . . . . . . . . . . . . . . . . . .13
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . .13
Connection to a cable box or satellite box . . . .14
Connection to an Audio System . . . . . . . . . . . . .15
Getting started . . . . . . . . . . . . . . . . . . .16
Easy DVD recording . . . . . . . . . . . . . . . . . . . . . .16
Channel setting . . . . . . . . . . . . . . . . . . . . . . . . . .18
Getting channels automatically . . . . . . . . . . . . . . . . .18
Adding/deleting channels . . . . . . . . . . . . . . . . . . . . .19
Guide channel setting . . . . . . . . . . . . . . . . . . . . . . .20
Selecting the TV stereo or SAP . . . . . . . . . . . . .22
Clock setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . .23
Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . . .24
Setting the daylight saving time . . . . . . . . . . . . . . . .26
Selecting the TV aspect ratio . . . . . . . . . . . . . . .27
Recording . . . . . . . . . . . . . . . . . . . . . . .28
Information on DVD recording . . . . . . . . . . . . . .28
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Recording speed . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Restrictions on recording . . . . . . . . . . . . . . . . . . . .28
Information on copy control . . . . . . . . . . . . . . . . . .29
Making discs playable in other DVD player (Finalize) 29
Formatting a disc . . . . . . . . . . . . . . . . . . . . . . . .30
Settings for the recording format to a blank disc . . .30
Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . . .32
Basic recording . . . . . . . . . . . . . . . . . . . . . . . . . .33
Checking the recording picture quality . . . . . . . . . .34
One-touch timer recording . . . . . . . . . . . . . . . .35
Timer recording . . . . . . . . . . . . . . . . . . . . . . . . .36
Hints for timer recording . . . . . . . . . . . . . . . . . . . . .38
Timer recording using VCR Plus+
Settings for an external source . . . . . . . . . . . . . .40
Connection to an external source . . . . . . . . . . . . . .40
Recording from an external source . . . . . . . . . . . . .41
Dubbing Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Finalizing the discs . . . . . . . . . . . . . . . . . . . . . . .44
Setting a disc to protect . . . . . . . . . . . . . . . . . . .45
Playing discs . . . . . . . . . . . . . . . . . . . . .46
Information on DVD play . . . . . . . . . . . . . . . . . .46
Guide to displays . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Playing discs using the disc menu . . . . . . . . . . . . . . .49
Playing discs using the title menu . . . . . . . . . . . . . . .50
Special playback . . . . . . . . . . . . . . . . . . . . . . . . .51
Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Fast forward / Fast reverse . . . . . . . . . . . . . . . . . . .51
Skipping TV commercials during play . . . . . . . . . . . . .52
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Step by step playback . . . . . . . . . . . . . . . . . . . . . . . .53
Slow forward / Slow reverse play . . . . . . . . . . . . . . .53
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Spatializer setting (Virtual surround) . . . . . . . . . . . .54
Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
®
system . . . . .39
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Title/Chapter search . . . . . . . . . . . . . . . . . . . . . . . .56
Track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Repeat/Random/Program play . . . . . . . . . . . . . .58
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Program play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Selecting the format of audio and video . . . . . .60
Switching audio soundtrack . . . . . . . . . . . . . . . . . . .60
Switching subtitles . . . . . . . . . . . . . . . . . . . . . . . . . .61
Switching camera angles . . . . . . . . . . . . . . . . . . . . . .62
Reducing block noise . . . . . . . . . . . . . . . . . . . . . . . .62
Editing . . . . . . . . . . . . . . . . . . . . . . . . .63
Information on disc editing . . . . . . . . . . . . . . . . .63
Guide to a title list . . . . . . . . . . . . . . . . . . . . . . . . . .63
Editing discs in Video mode . . . . . . . . . . . . . . . . . . .63
Editing discs in VR mode . . . . . . . . . . . . . . . . . . . . .64
Editing DVD-RW discs in Video mode . . . . . . . .65
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .66
Setting or clearing chapter markers . . . . . . . . . . . . .68
Editing DVD-RW discs in VR mode (Original) . .69
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .70
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .71
Setting or clearing chapter markers . . . . . . . . . . . . .73
Setting pictures for thumbnails . . . . . . . . . . . . . . . . .74
Setting titles to protect . . . . . . . . . . . . . . . . . . . . . .76
Releasing titles from protecting . . . . . . . . . . . . . . . .77
Editing DVD-RW discs in VR mode (Playlist) . . .78
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .79
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .80
Setting or clearing chapter markers . . . . . . . . . . . . .82
Setting pictures for thumbnails . . . . . . . . . . . . . . . . .83
Adding titles to a Playlist . . . . . . . . . . . . . . . . . . . . .85
Deleting a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Editing DVD-R discs . . . . . . . . . . . . . . . . . . . . . .87
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .88
Changing the SETUP menu . . . . . . . . .89
Tour of the SETUP menu . . . . . . . . . . . . . . . . . .89
Settings for Language . . . . . . . . . . . . . . . . . . . . .90
Settings for Display . . . . . . . . . . . . . . . . . . . . . . .92
Settings for Audio . . . . . . . . . . . . . . . . . . . . . . . .94
Settings for Parental lock level . . . . . . . . . . . . . .96
VCR functions . . . . . . . . . . . . . . . . . . .98
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Recording and One-touch timer recording . . . .98
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
One-touch timer recording . . . . . . . . . . . . . . . . . . . .99
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Index search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Other operations . . . . . . . . . . . . . . . . . . . . . . .100
Others . . . . . . . . . . . . . . . . . . . . . . . .101
Tr oubleshooting . . . . . . . . . . . . . . . . . . . . . . . .101
RF converter output . . . . . . . . . . . . . . . . . . . . .104
Language code . . . . . . . . . . . . . . . . . . . . . . . . .105
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Español . . . . . . . . . . . . . . . . . . . . . . . .108
Français . . . . . . . . . . . . . . . . . . . . . . .112
Before you start Connections
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
5
Before you start
Features
This unit not only plays DVDs, CDs and VHS tapes but also offers features for you to record to DVD discs and edit them after that.The following features are offered with this unit.
Recording
VCR modeDVD mode
This unit is compatible with both DVD-RW, which is rewritable repeatedly and DVD-R, which is available for recording once. Also, this unit allows you to record to the video cassette tape. You can choose either one for your convenience.
Up to 8 programs recording:
You can program the unit to record up to 8 programs, up to a year in advance. Daily or weekly program recordings are also available.
One-touch timer recording:
You can easily set a recording time as you prefer. Every time the REC/OTR button on the remote control or the RECORD button on the front panel pressed during recording, the recording time will be increased by 30 min­utes up to 8 hours.The recording automatically stops when the recording time you set is reached.
The VCR Plus+ system:
You can program the automatic timer recording using the
PlusCode programming numbers that are printed in most
newspaper TV listings and TV Guide magazine.
Dubbing mode:
You can copy a DVD disc to a videotape or copy a video­tape to a DVD disc.This function will be possible only if the DVD disc and the videotape are not copy protected.
DVD mode
REC MONITOR:
You can confirm the picture quality for recording in the current recording speed which you set. If you want to change the recording speed, press REC SPEED button to set the desired recording mode.
Automatic Chapter marker setting:
Chapter markers will be put on recordings as you set in SETUP menu before attempting to record.
Automatic Title menu making:
The unit makes title menus automatically when finalizing the disc which are recorded in Video mode.
Automatic PLAYLIST making (VR mode):
A Playlist will be prepared from an Original list, so that you can edit titles in a Playlist as you prefer. An Original list is kept as it is.
Play
DVD mode
Spatializer:
You can enjoy stereophonic virtual sound of spatializer® N-2-2 ultra™ method provided by Desper Products, Inc.
Theater surround sound in your home:
When connecting the unit to an amplifier or a decoder which is compatible with Dolby Digital or DTS, you are allowed to experience the theater surround sound from discs with surround sound system.
Quick search for what you want to watch:
You can easily find the part you want to watch using the search func­tion. Search for a desired point on a disc by title, chapter or time.
Start to play from Original and Playlist (VR mode):
Title playing is available from either an Original list or Playlist.
VCR mode
Quick search for what you want to watch:
You can easily find the part you want to watch using the Index search/Time search functions. An index mark will be assigned at the beginning of each recording you make. For Time search function, you can go to a specific point on a tape by entering the exact amount of time you wish to skip.
Editing
DVD mode
Setting/Clearing chapter markers:
You can easily add chapter markers anywhere in your recordings for easy editing. (VR mode)
Making your own Playlist:
With the original remains as it is, you can edit titles on Various playlist as you prefer. Putting names on titles. Setting pictures for thumbnails. Setting/clearing chapter markers. Deleting parts of titles, etc.
Protecting titles:
To avoid editing or erasing titles, the protect function is useful when it is ON in the original list.
Compatibility
DVD mode
Available for playing discs recorded in Video mode on a regular DVD player (Video mode):
Discs recorded in the Video mode can be played on regular DVD players, including computer DVD drives compatible with DVD-Video playback*.You will need to finalize the discs recorded in Video mode to play in other DVD players.
* DVD-Video Format (Video mode) is a new format for record­ing on DVD-R/RW discs that was approved by the DVD Forum in 2000. Adoption of this format is optional for manufactures of DVD playback devices and there are DVD-Video players, DVD-ROM drives or other DVD playback devices that do not play DVD-R/RW discs recorded in the DVD-Video Format.
Others
Progressive Scan system
Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolu­tion than that of traditional television signals.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
Certain audio features of this product manufac­tured under a license from Desper Products, Inc. Spatializer® N-2-2 Ultra™ and the circle-in-square device are trademarks owned by Desper Products, Inc.
6
Front Panel
POWER
REW F.FWD RECORD
CHANNEL
SELECT
STOP PLAY RECORD
S-VIDEO
VIDEO L - AUDIO - R
DUBBING
OPEN/CLOSE
PLAY
STOP/EJECT
VCR
DVD
1
222120
19
2
18
17 15 14 13 101112
6
34
16 9 8 7
5
DVD
DVD/VCR
ANTENNA
IN
AUDIO OUTAUDIO IN
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COAXIAL
OPTICAL
COMPONENT VIDEO OUT
VIDEO OUTVIDEO IN
LY
IN
OUT
P
B/
C
B
PR/ C
R
L
R
L
R
R
OUT
634521
7
10
98
1112
Before you start
Functional overview
Before you start Connections
1.POWER button (DVD/VCR)
Press to turn the unit on and off. If timer programmings have been set, press to set the unit in timer-standby mode. Press to cancel the timer standby mode, then turn the unit on.
2. Cassette compartment (VCR)
Insert a tape here.
3. A OPEN/CLOSE button (DVD)
Press to open or close the disc tray.
4. VCR SELECT indicator
This indicator appears when the VCR output mode is selected.
5.DVD SELECT indicator
This indicator appears when the DVD output mode is selected.
6. Disc tray (DVD)
Place a disc when open.
7.AUDIO (L/R) input jacks (LINE2) (DVD/VCR)
Use to connect external equipment with standard audio cables.
8. VIDEO input jack (LINE2) (DVD/VCR)
Use to connect external equipment with a standard video cable.
9. S-VIDEO input jack (LINE2) (DVD only)
Use to connect the S-Video output of external equip­ment with an S-Video cable.
10. RECORD button (DVD)
Press once to start a recording. Press repeatedly to start a One-Touch Recording.
11. PLAY button (DVD)
Press to start or resume play.
12.STOP button (DVD)
Press to stop playback or recording.
Rear Panel
Press to stop the proceeding timer recording in DVD.
13. SELECT button (DVD/VCR)
Press to select the component you wish to operate.
14. DUBBING button (DVD/VCR)
Press to start VCR to DVD (DVD to VCR) duplication which you set in the SETUP menu.
15. CHANNEL L / K button (DVD/VCR)
Press to change the channel up and down.
16. Display (DVD/VCR)
Refer to “Guide to Displays on the front panel” on page 12.
17. Remote control sensor (DVD/VCR)
Receive signals from your remote control so that you can control the unit from a distance.
18. RECORD button (VCR)
Press once to start a recording. Press repeatedly to start a One-Touch Recording.
19.PLAY button (VCR)
Press to start playback.
20.STOP/EJECT button (VCR) EJECTbutton-
Press to remove the tape from the unit.
STOP button-Press to stop the tape motion. Press to stop the proceeding timer recording in VCR.
21.F.FWD button (VCR)
Press to rapidly advance the tape, or view the picture rapidly in forward during playback. (Forward Search)
22. REW button (VCR)
Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode. (Rewind Search)
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
1.AC Power Cord (DVD/VCR)
Connect to a standard AC outlet to supply power to this unit.
2. S-VIDEO IN jack (LINE1)
(DVD only)
Use to connect the S-Video output of external equip­ment with an S-Video cable.
COMPONENT VIDEO OUT jacks (DVD only)
3.
Use to connect a TV monitor with component video inputs with component video cables.
4.AUDIO IN jacks (LINE1) (DVD/VCR)
Use to connect external equipment with standard audio cables.
5.AUDIO OUT (L/R) jacks (DVD/VCR)
Use to connect a TV monitor,AV receiver or other equipment with standard audio cables.
6. ANTENNA IN jack (DVD/VCR)
Use to connect an antenna.
7. ANTENNA OUT jack (DVD/VCR)
Use to connect an antenna cable to pass the signal from the ANTENNA IN to your TV monitor.
Note: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause perma-
nent damage to the unit.
8. VIDEO OUT jack (DVD/VCR)
Use to connect a TV monitor,AV receiver or other equipment with a standard video cable.
9.VIDEO IN jack (LINE1) (DVD/VCR)
Use to connect external equipment with a standard video cable.
10. S-VIDEO OUT jack (DVD only)
Use to connect the S-Video input of a TV monitor,AV receiver or other equipment with an S-Video cable.
11.AUDIO OUT jacks (DVD only)
Use to connect a TV monitor,AV receiver or other equipment with standard audio cables.
12. DIGITAL AUDIO OUT (OPTICAL/COAXIAL) jacks (DVD only)
Use to connect an AV receiver, Dolby Digital decoder, DTS decoder or other equipment with digital input jacks with a digital coaxial cable or a digital optical cable.
These jacks are useful only in DVD mode.
VCR functions
Others
Español
Français
7
Remote Control
.@/:
GHI
PQRS
REC
MONITOR
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
OPEN/ CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
17
23
25
27
28
29
18
19
21
20
22
24
26
30
POWER
1
+
VCR Plus
2
SEARCH
MODE
3
CM SKIP
4
ZOOM
5
CLEAR/ C.RESET
6
7
8
9
RETURN
10
11
12
13
14
15
16
1.
POWER button (DVD/VCR)
VCR
SLOW
SKIP
Press to turn the unit on and off. If timer programmings have been set, press to set the unit in timer-standby mode. Press to cancel the timer standby mode, then turn the unit on.
2. VCR Plus+ button (DVD/VCR)
Press to set a timer recording with the VCR Plus+ program­ming system. Press to display the timer program setting menu.
3.
SEARCH MODE button (VCR)
Press to call up the index or time search menu.
4. CM SKIP button (DVD)
During playback, press to skip 30 seconds.
5. ZOOM button (DVD)
During playback, press to enlarge the picture on the screen.
6. CLEAR/C.RESET button (DVD/VCR)
• DVD mode Press to clear the password once entered, to cancel the program­ming for CD, to clear the select­ing marker number in the marker setup mode or to clear the pro­gram once entered in the timer recording setting mode,etc.
• VCR mode Press to reset the tape counter.
8
Before you start
Functional overview (cont’d)
7.
REC MONITOR button (DVD)
Press to check the video to be recorded before attempting.
8.
MENU/LIST button (DVD)
Press to display the Disc menu. Press to change ORIGINAL and PLAYLIST on the TV screen. (VR mode only)
9. K / L / { / B buttons (DVD/VCR)
Press to select items or settings.
10. RETURN button (DVD/VCR)
Press to return to the previ­ously displayed menu screen.
11. VCR button
Press to activate the remote control in VCR mode. (Refer to page 9.) Press to select the VCR out­put mode.
12. SLOW button (VCR)
During playback, press to view the video tape in slow motion.
13. SKIP H button (DVD)
During playback, press to skip to the previous chapter or track. Also during pause, press to play reverse step by step.
SKIP G button (DVD)
During playback, press to skip to the next chapter or track. Also during pause, press to play forward step by step.
14. REWE
button (DVD/VCR)
• DVD mode During playback, press to play fast reverse or during pause, press to play slow reverse.
• VCR mode Press to rewind the tape or to view the picture rapidly in reverse during the playback mode.
15.STOP C button (DVD/VCR)
Press to stop playback or recording.
16. PAUSE F button (DVD/VCR)
Press to pause play or recording.
17.
OPEN/CLOSE A button (DVD)
Press to open or close the disc tray.
18.
Number buttons (DVD/VCR)
Press to select channel numbers. Press to select a title/chapter/track on display or a TV channel. Press to enter the VCR Plus+ programming number. Also press to enter values for the settings in the SETUP menu.
19.
20. AUDIO button (VCR)
21.
22. ENTER button
23.
24.
25. DVD button
26. REC SPEED button
27.
28.
29. FWD D button
30. PLAY B button
DISPLAY button (DVD/VCR)
Press to display or change the on-screen display.
During playback a HiFi video tape, press to change the AUDIO OUT setting “HIFI” and “MONO”.
TOP MENU button (DVD)
Press to display the top menu.
(DVD/VCR)
Press to confirm or select menu items.
SETUP button (DVD/VCR)
Press to display the setup menu. During DVD playback, press and hold for more than 3 seconds to switch to the progressive scanning mode or the interlace mode.
VIDEO/TV button (DVD/VCR)
Press to select VIDEO or TV position.
Press to activate the remote control in DVD mode. (Refer to page 9.) Press to select the DVD out­put mode.
(DVD/VCR)
Press to switch the recording speed.
REC/OTR button (DVD/VCR)
Press once to start a record­ing. Press repeatedly to start a One-Touch Recording.
CH K / L buttons (DVD/VCR)
• DVD mode Press to change the channel up and down.
• VCR mode Press to change the channel up and down. Press to adjust the tracking during playback or in slow motion of the tape. Also while playback is in still mode, you can adjust the picture blurred vertically.
(DVD/VCR)
• DVD mode During playback, press to play fast forward or during pause, press to play slow forward.
• VCR mode Press to rapidly advance the tape or view the picture rapidly in forward during playback.
(DVD/VCR)
Press to start or resume play.
Before you start
1
2
3
POWER
REW F.FWD RECORD
CHANNEL
SELECT
STOP PLAY RECORD
S-VIDEO
VIDEO L - AUDIO - R
DUBBING
OPEN/CLOSE
PLAY
STOP/EJECT
VCR
DVD
SELECT
VCR
DVD
POWER
OPEN/ CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/ C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
SELECT button
DVD button
VCR button
DVD SELECT indicator
VCR SELECT indicator
Functional overview (cont’d)
Before you start Connections
Installing batteries in the remote control
Install two AA batteries (supplied) matching the polarity indicated inside battery compartment of the remote control.
Note:
Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together, although they may look similar, different batteries may have different voltages.
• Make sure that the plus and minus ends of each battery match the indications in the battery com­partment.
• Remove batteries from equipment that is not going to be used for a month or more.
•When disposing of used batteries, please comply with governmental regulations or environmental public instruction rules that apply in your country or area.
• Do not recharge, short-circuit, heat, burn or disas­semble batteries.
Using a remote control
Keep in mind the following when using the remote control:
• Make sure that there is no obstacle between the remote control and the remote sensor on the unit.
•Use within the operating range and angle as shown.
• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the remote sensor of the unit.
• Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit.
• Replace the batteries when you notice a fall off in the operating range of the remote control.
PO W
E
60˚
R
RE W
F .F WD
S T O
P / E J
E C T
P LA
Y
RE CO
R D
O PE
N/ CL
O SE
C H AN N
EL
D U BB
IN G
S EL
EC T
S T
VC
OP
R
P L
AY D V D
RE
C OR
D
S
-V ID
EO
V I DEO
L - A
UDIO
- R
Within about 23feet (7m)
Remote control
Getting started
Recording Playing discs
Editing
VCR/DVD recorder Switching
Because this product is a combination of a VCR and a DVD recorder, you must select first which com­ponent you wish to operate with the SELECT button.
VCR MODE
Press the VCR button on the remote control.
(Verify that the VCR SELECT indicator is lit.)
Press the DVD button on the remote control.
(Verify that the DVD SELECT indicator is lit.)
Note
Pressing only the SELECT button on the front panel DOES NOT switch the mode of the remote control.You MUST select the correct mode on the remote control.
Pressing the SETUP or the VCR Plus+ but- ton switches the unit to the DVD mode.
DVD MODE
Changing the SETUP menu
VCR functions
Others
Español
Français
9
Before you start
Functional overview (cont’d)
Guide to On Screen Menu
This unit uses the following types of display for most operations. SETUP/DISC/CD menu,Title list, and DIS­PLAY, which allows you to change the playing status of disc during play. DISPLAY also gives you some disc information for checking the status of the disc.
SETUP/DISC/CD menu
Press SETUP button to display the setup main menu, then choose either of SETUP/DISC/CD by pressing { / B buttons.Then, press ENTER button to display each menu. This provides entries to all main functions of the unit.
“SETUP” is available only in the Stop mode.
Setup Menu
Setup
1 2 3
4 5 6
Playback Setting
1. Playback:
To set up the unit to play discs as you prefer.
2. Recording:
To set up the unit to record to discs or tapes as you prefer.
3. Display:
To set up the OSD screen as you prefer.
4. Select Video:
To choose a line input to record to DVD discs from other video equipment.
5. Clock:
To set up the clock of the unit as you need.
6. Channel:
To make the channel setting of the unit as you prefer.
“DISC” is available only when a DVD-R/RW disc is inserted into the unit. When a DVD-Video disc (commercially available), a new DVD-R disc or the finalized DVD-R disc is inserted into the unit, you cannot select “DISC”.
Disc Setting
Disc
Edit
Format
Finalize
Disc Protect OFF ON
1 2 3
4
1. Edit:
Turns on a title list, (When a disc with VR mode is inserted, 'Original' or 'PlayList' is available.), which shows the recorded titles on the disc.
2. Format:
Allows you to erase all of the recorded content on the disc. The disc will be completely blank.
3. Finalize:
Allows you to finalize a disc recorded titles.
4. Disc Protect (VR mode only) :
Allows you to protect a disc from accidental editing or recording.
“CD” is available only when an Audio CD disc or a CD­R/RW disc with MP3 files is inserted into the unit.
CD Playback Mode
CD Playback Mode
Random Play
Program Play
1 2
1. Random Play:
To set the random play program­ming.
2. Program Play(Audio CD only):
To set the program playing.
10
DISPLAY menu
)
DVD mode
First:
Press DISPLAY button to call up the display menu.This menu will give you the information on the playing disc. Some operations are available while disc is playing.
Details are on page 46.
DVD
4
11 00:00:00
5
1
DVD-RW
Video mode
SP 1:25 Rem.
CH 1
Before you start
Functional overview (cont’d)
1. Indicates a disc type and a
format mode. Note: In some descriptions on this manual, only one disc type is indicated as an example.
2. Indicates a recording mode
and possible recording time left.
3. Indicates a current channel
number.
4. Indicates a title number, chap-
ter number and the time elapsed of disc play.
2 3
5. Each icon means:
: Search
: Audio
: Subtitle
: Angle (except VR mode
: Repeat
: Marker
: Noise Reduction
: Zoom
: Spatializer
Before you start Connections
Getting started
Recording Playing discs
VCR mode
First:
VCR
Press DISPLAY button to call up the display menu.
1
0:00:00 HIFISP
2
CH21
4 53
1. Playback status of the current
tape.
2. Indicates a current channel
number and an audio status of the program.
3. Indicates a recording speed
only five seconds.
4. Indicates a Tape Counter.
5. Audio status of the current
tape.
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
11
Before you start
1 6
3
5
2
4
7
Functional overview (cont’d)
Guide to Displays on the front panel
1. Current status of the unit
: Appears when a disc or a
tape play is paused.
: Appears when playing a
disc or a tape.
: Appears when the timer
programming has been set and is proceeding.
: Appears during recording
process.
: Appears during repeat play.
:
Appears when a tape is in the unit.
Display message
2. Disc type and Current status of the unit
:
Appears when an audio CD or a disc with MP3 files is inserted in the disc tray.
:
Appears when a DVD disc is inserted in the disc tray. Appears when the timer recording is proceeding in DVD. Appears when DVD is in the timer recording stand­by mode.
: Appears when a DVD-R disc is inserted in the disc tray.
: Appears when a DVD­RW disc is inserted in the disc tray.
:
Appears when the timer recording is proceeding in VCR. Appears when VCR is in the timer recording stand­by mode.
: Appears during VCR to DVD duplication process.
: Appears during DVD to VCR duplication process.
3. Recording speed
Indicates the recording speed of the disc or the tape.
4. Title/Track and Chapter mark
: Appears when indicating
a title/track number.
: Appears when indicating
a chapter number.
5. Displays the following
• Playing time / remaining time
• Current title / chapter / track number
• Recording time
• Clock
• Channel number
• VCR tape counter
•OTR remaining time
6. : Appears in the after-
noon with the clock displaying.
7. :
Appears when the pro­gressive scan system is activated.
1. Appears when the disc tray is
opening.
1
2
3
4
2. Appears when the disc tray is
closing.
3. Appears when a disc is loading
in the disc tray.
4. Appears when recording data
is writing on to the disc.
12
Connections
DVD/VCR
ANTENNA
IN
AUDIO OUTAUDIO IN
COAXIAL
OPTICAL
COMPONENT VIDEO OUT
VIDEO OUTVIDEO IN
LY
IN
OUT
P
B/
C
B
PR/ C
R
L
R
L
R
R
OUT
DVD
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COMPONENT VIDEO OUT
(Back of TV)
Plug in the AC power cord of this unit.
or
Cable Signal
or
Cable Signal
Connect
Disconnect
Antenna
Antenna
(Back of this unit)
(Back of TV)
RF Cable (supplied)
Connect
3
2
1
4
DVD/VCR
ANTENNAINAUDIO OUTAUDIO IN
L
VIDEO OUTVIDEO IN
LY
IN
OUT
P
B
/
C
B
PR/ C
R
L
R
L
R
R
OUT
DVD
S-VIDEO
AUDIO OUT
COMPONENT VIDEO OUT
DVD/VCR
ANTENNAINAUDIO OUTAUDIO IN
COAXIAL
OPTICAL
VIDEO OUTVIDEO IN
LY
IN
OUT
P
B
/
C
B
PR/ C
R
L
R
L
R
R
OUT
DVD
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COMPONENT VIDEO OUT
DVD
AUDIO
OUT
DVD
S-VIDEO
DVD
COMPONENT VIDEO OUT
Y
P
B
/
C
B
PR/ C
R
L
R
OUT
DVD/VCR
AUDIO OUT
L
R
DVD/VCR
VIDEO OUT
AUDIO IN VIDEO IN
S-VIDEO IN
PB/C
B
Y
P
R/CR
COMPONENT
VIDEO IN
or
SETUP
RETURN
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
Connection to a TV
Before you start Connections
Getting started
Make one of the following connections, depending on the capabilities of your existing equipment.
Basic Audio
Method 1
Good picture
Method 2 Method 3
Better picture Best picture
Recording Playing discs
TV
Audio cable
(supplied)
Video cable (supplied)
This unit
VIDEO OUT
These jacks are useful only in DVD mode.
Note
AUDIO OUT
• Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.
Method 2 and method 3 are only useful in DVD mode.
If your TV is compatible with 525p (480p) progressive scanning and you want
You must select the connection Method 3 above and progressive scanning mode.To set the mode, press and hold the SETUP button on the remote control for more than 3 sec-
to enjoy that high quality picture;
onds during DVD playback, so that “P.SCAN” will appear on the display of this unit.
If your TV is not compatible with progressive scanning;
Use this unit in interlace mode. Make sure that no “P.SCAN” is on the display of this unit. If not, press and hold the SETUP button on the remote control for more than 3 seconds during DVD playback, so that “P.SCAN” on the display of this unit will disappear.
S-Video cable (commercially available)
S-VIDEO OUT
Component Video cables (commercially available)
COMPONENT VIDEO OUT
more than 3 seconds
during DVD playback
[Interlace mode]
[Progressive scanning mode]
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
13
Connections
DVD DVD/VCR
ANTENNA
IN
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COAXIAL
OPTICAL
COMPONENT
VIDEO OUT
Y
IN
OUT
P
B
PR
L
R
OUT
RF Cable
(supplied)
(Back of this unit)
IN
OUT
(Back of TV)
Cable
Signal
Connection A
(Cable box or
Satellite box)
DVD DVD/VCR
ANTENNA
IN
S-VIDEO
AUDIO
OUT
DIGITAL
AUDIO OUT
COAXIAL
OPTICAL
COMPONENT VIDEO OUT
Y
IN
OUT
P
B
PR
L
R
OUT
RF Cable (supplied)
RF Cable
(Back of TV)
IN
OUT
(Cable box or
Satellite box)
Cable
Signal
Connection B
(Back of this unit)
Connection to a cable box or satellite box
Select this connection when you want to view or record a scrambled channel.With this connection, channels cannot be changed on this unit.You can view or record ONLY the channels you have selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be viewed.
If you use the VCR Plus+ programming system, set the Cable/TV channel to 03 or 04 (Cable Box/DBS output channel) for every VCR Plus+channel in the Channel Line-Up Chart.You must set the Cable Box/DBS to the channel you want to record; leave the Cable Box/DBS on for the timer recording. (Refer to page 20.)
To select channels of the cable box or satellite box
1) Turn on this unit by pressing POWER button.Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).
• If noise appears on the TV screen
• If you use the channel 4, you will need to change this unit’s RF output to channel 4. Refer to “RF converter output” on page 104.
2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).
3) At the cable box or satellite box, select the channel you want to view or record.
,press VIDEO/TV button on the remote control.
Select this connection when you want to change channels on this unit.With this connection, you may watch one channel while recording another.
• You may not view or record a scrambled channel.
T
o select channels of the cable box or satellite box
1)
At the cable box or satellite box, select channel 3 or 4 (the same channel as this unit’s RF output channel.)
• Refer to “RF converter output” on page 104.
2) At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box.
3) Turn on this unit by pressing POWER button. Then select the channel you want to view or record.
• If noise appears on the TV screen
,press VIDEO/TV button on the remote control.
To playback a DVD disc or a tape
Before trying to playback DVD or tape, you MUST steps 1) to 2) above.
• Refer to “Playback” on pages 47-48, 98.
T
o view one channel while recording another
1) While you are recording on this unit, press VIDEO/TV button.
2) At the cable box or satellite box, select the channel you want to view.
Note to the Cable TV System Installer :
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable
entry as possible.
14
Connections
DVD/VCR
AUDIO OUT
L
R
L
R
DVD
AUDIO
OUT
or
DVD
DIGITAL
AUDIO OUT
COAXIAL
OPTICAL
COAXIAL
OPTICAL
Connection to an Audio System
• When you change the connections, all devices should be turned off.
• Refer to each owner’s manual for further information on other devices.
Before you start Connections
Method 1
Stereo system
Analog audio
Method 2 Dolby Digital decoder, DTS
decoder, MD deck or DAT deck
input jacks
AUDIO
Digital audio input jacks
Audio cable
(supplied)
Audio Optical
Digital cable
(commercially
available)
or
Audio Coaxial
Digital cable
(commercially
available)
This unit
DIGITAL
AUDIO OUT
AUDIO OUT
Note
• If output is Dolby Digital encoded audio, connect to a Dolby Digital decoder and set “Dolby Digital” to “Stream” for the “Digital Out” setting in the SETUP menu. (Refer to pages 94-95.)
(usefull only in
DVD mode)
If output is DTS encoded audio, connect to a DTS decoder and set “DTS” to “ON” for the “Digital Out” setting in the SETUP menu. (Refer to pages 94-95.)
• The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or DAT deck.
Unless connected to a Dolby Digital decoder or a DTS decoder, set “Dolby Digital” to “PCM” and “DTS” to “OFF” for the “Digital Out” setting in the SETUP menu. Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to pages 94-95.)
• Set “Dolby Digital” to “PCM” for the “Digital Out” setting in the SETUP menu for connecting to an MD deck or DAT deck. (Refer to pages 94-95.)
By hooking this unit up to a Multi-channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital 5.1 channel surround sound as heard in the movie theaters.
By hooking this unit up to the DTS decoder, you can enjoy
5.1 channel surround system which reproduces the original sound as truthfully as possible. 5.1 channel surround system is developed by the Digital Theater System, Inc.
Optical cable (not supplied)
• Optical cable (not supplied) may be damaged when bent at sharp angles. Ensure cables are coiled in loops with a diameter of 15 cm or more when storing them.
• Use a cable which is 3 m or shorter.
• Insert cable plugs firmly into the connectors when making connections.
• If a plug has minor scratches or is dirty, clean it with a soft cloth before inserting it into a connector.
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
15
Getting started
Loading
Easy DVD recording
The following will help you to understand easily how to record to DVD discs.
Note:
Make sure batteries are in the remote control and you have connected this unit and the TV correctly.
Step 1:
Choose a disc type
There are several types of recordable DVD discs to choose from. Choose a recordable DVD disc type based on your playing/recording/editing require­ments. See “DVD disc type” below.
This unit can record on the follow­ing type of discs only.
(or)
* This unit cannot record on the fol-
lowing discs.
•DVD-R General Ver 2.0 / 8x
•DVD-RW Ver 1.2 / 2-4x CPRM com­patible
For example, when you want to record repeatedly on the same disc, or when you want to edit the disc after recording, select the rewritable DVD-RW type disc.
When you want to save recordings without any alteration, a non­rewritable DVD-R can be your choice.
Step 2: Insert a blank disc
Turn on the unit
1
Open the disc tray
2
Close the disc tray
3
Remote Control
1
POWER
+
VCR Plus
POWER
+
VCR Plus
This operation may take a while to be recognized.
OPEN/ CLOSE
ABC DEF
.@/:
OPEN/ CLOSE
ABC DEF
.@/:
2
3
Step 3: Select the Recording speed
Select the DVD
1
mode
Select the recording
2
speed
TOP MENUMENU/LIST
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
DVD
REC/OTR
CH
SETUP
FWDREW
SP 2:01 Rem.
2
RETURN
VCR
SLOW
SKIP
1
DVD disc types
16
Format the disc
Insert the disc in the unit. Then format the disc from SETUP menu.Video format (Video mode) or Video recording format (VR mode) will be available depending on the disc type inserted.
This is necessary to pre­pare the disc for record­ing. Details are on pages 30-32.
* When you format, the entire contents on that disc will be erased.
Getting started
Easy DVD recording (Cont’d)
Before you start Connections
Step 4: Select the desired channel
.@/:
GHI
PQRS
REC
MONITOR
STOP PLAY
OPEN/
CLOSE
ABC
JKL
MNO
TUV
WXYZ
SPACE
AUDIO DISPLAY
CH
FWDREW
DEF
CH 1
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
+
SKIP
Step 5: Record to DVD discs
TOP MENUMENU/LIST
VIDEO/TV
REC
SPEED
STOP PLAY
SETUP
DVD
REC/OTR
CH
RETURN
VCR
SLOW
SKIP
I
Step 6: Stop the Record
VCR
VIDEO/TV
DVD
REC
SLOW
REC/OTR
SPEED
SKIP
CH
STOP PLAY
FWDREW
PAUSE
Writing to Disc
This operation may take a while to be completed.
58%
Hint 1: Play the recorded contents
You can select the title you want to play from a displayed menu and immediately start to play. Recorded contents are very accessible on a disc, the procedure is really simple as you choose a title on a chapter from the menu screen.
What are titles and chapters?
The contents of DVD disc are generally divided into titles.Titles may be further subdivided into chapters.
Start Rec. Stop/Start Stop Rec.
Title 1 Title 2
Chapter 1 Chapter 1Chapter 2 Chapter 3 Chapter 2
Hint 2: Edit the recorded disc
You will find editing discs very easy.This unit offers convenient edit functions, which are possible only with DVD-R/RW discs.
You can edit the following from a title list.
• Putting names on titles
• Setting pictures for thumbnails (VR mode)
•Setting/clearing chapter markers
• Deleting parts of titles or scenes (VR mode)
Title Delete :This deletes an entire scene permanently from the disc. Scene Delete :This allows a user to edit within a specific scene (ex. commercials).
Original and Playlist (VR mode)
You can edit the recordings in Playlist without changing the original recordings. A Playlist does not take up much disc space.
What “Original” or “Playlist” is for?
Throughout this manual, you will find Original and Playlist to refer to the actual content and the edited version.
Original content refers to what’s actually recorded on the disc.
Playlist content refers to the edited version of the disc; how the Original content is to be played.
Finalizing a Disc
• This will allow a disc that is recorded on our unit to be played back on a different DVD player- without
finalization it will not be playable on another player. After finalizing a disc if the recording was in video mode, you can not edit any information that is on that disc.
• If you have recorded in VR mode on DVD-RW disc then editing is still permitted after finalizing.
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
17
Français
All channels are stored in the unit
POWER
OPEN/ CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
when purchased.We recommend that you program available chan­nels in your area using “Auto Preset” in the Channel Preset of the SETUP menu.
Getting channels auto­matically
1
Press POWER button to turn on the unit.
2
Turn the TV on and be sure to select the input to which the unit is connected.
3
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
18
Getting started
Channel setting
4
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
5
Select “Channel” using K / L / { / B buttons, then press ENTER button.
Channel Preset menu will appear.
Setup > Channel Preset
Auto Preset
Manual Preset
Guide Channel Setting
TV Audio Select
VCR DV D
Stereo
6
Select “Auto Preset” using K / L buttons, then press ENTER button.
The unit will start getting chan­nels available in your area.
CH 18
Auto Presetting Now
7
Press SETUP button to exit.
•You can select only the channels memorized in this unit by using the CHANNEL buttons.
1
4 5
3
6
7
To select a channel
You can select a channel by directly entering channel using the Number buttons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For exam­ple: 117, press 1,1,7)
• You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). You can select the line input
• mode (“L1” or “L2”).To select “L1” by pressing [0],[0],[1].To select “L2” by pressing [0],[0],[2].Details are on page 41.
Note
• If the auto presetting is can-
celled during presetting, some channels not yet preset may not be received.
• The selection will depend on
how you receive the TV chan­nels.
To cancel the auto preset­ting during scanning:
Press RETURN button or SETUP button to cancel.
Adding/deleting channels
Getting started
Channel setting (cont’d)
Before you start Connections
The channels you no longer receive or seldom watch can be deleted from the memory.You also may add channels into memory.
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
4
Select “Manual Preset” using K / L buttons, then press
ENTER button.
Manual Preset menu will appear.
Setup > Channel Preset > Manual Preset
CH2
Add Delete
5
Select the channel number to add or delete.
Press { button to move to a lower channel number.
Press B button to move to a higher channel number.
Setup > Channel Preset > Manual Preset
CH18
Add Delete
2 3 4 5 6
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
OPEN/ CLOSE
DEF
MNO
WXYZ
1 7
Getting started
Recording Playing discs
Editing
Playback Setting
3
Select “Channel” using K / L / { / B buttons, then press ENTER button.
Channel Preset menu will appear.
Setup > Channel Preset
Auto Preset
Manual Preset
Guide Channel Setting
TV Audio Select
VCR DV D
Stereo
6
Select “Add” or “Delete” using K / L buttons, then
press ENTER button.
The channel number will be added or deleted from the chan­nel memory.Then next channel number will appear so that you can continue adding or deleting channels.
7
Press SETUP button to exit.
Changing the SETUP menu
VCR functions
Others
Español
Français
19
Getting started
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Channel setting (cont’d)
Guide channel setting
First, fill in the boxes on this page:
1. Write your local channel numbers in “TV Channel” column, which you can receive in your area by chan­nel preset.
2. Write local TV stations corresponding TV Channel in “Call letters” column, and write guide channel num­bers corresponding call letters in “Guide Channel” column, consulting your TV guide magazine or the TV listings of your local newspaper.
Remember:
If your cable box or satellite box is connected as in “Connection A” on page 14,TV Channel number must be channel 3 or 4 for every guide channel number.
Now, compare the channel numbers you have writ­ten in the Guide Channel and TV Channel columns. You must set all of these channel numbers that don’t match using the following procedure before you pro­gram the automatic timer recording using the VCR Plus+ system.
• This setting only needs to be set once, but must be done again if you have moved to a different area and channel numbers have been changed.
Call letters (Local TV station)
Channel Line-Up Chart
Guide Channel (Guide channel number)
TV Channel (Local channel number)
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
2
Select SETUP using { / B buttons, then press ENTER button.
SETUP menu will appear.
20
Screen:
Setup Menu
Setup
Playback Setting
3
Select “Channel” using K / L / { / B buttons, then press ENTER button.
Channel Preset menu will appear.
Setup > Channel Preset
Auto Preset
Manual Preset
Guide Channel Setting
TV Audio Select
VCR DV D
Stereo
2 3
1
Getting started
Channel setting (cont’d)
Before you start Connections
4
Select “Guide Channel Setting” using K / L buttons,
then press ENTER button.
Guide Channel Setting list will appear.
Setup> Channel Preset> Guide Channel Setting
Guide Channel
:
TV Channel
1
2
3
4
5
6
CH1
: :
CH---
:
CH---
:
CH---
:
CH---
:
CH---
5
Assign channel numbers to the guide channels as neces­sary.
Look in your TV guide to see which channel numbers should be assigned to which guide channels.
1. Choose a guide channel num­ber using K / L buttons, then press ENTER button.
A cursor will move to a TV chan­nel. If the channel you wish to set is not on the screen, press { / B buttons to change the displayed page until you reach the correct page.
2. Select an external input (L) or CATV/TV (CH) using { / B buttons.
3. Enter a TV channel using K / L buttons or number buttons,
then press ENTER button.
The channel number is assigned.
6
Press SETUP button to exit SETUP menu.
4 5
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
CLOSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
OPEN/
DEF
MNO
WXYZ
Getting started
Recording Playing discs
6
Editing
Changing the SETUP menu
VCR functions
Others
To continue assigning, repeat the steps 1-3.
Note
•To erase a TV channel, press { button at step 5-3.
Español
Français
21
Selecting the TV stereo or SAP
You can select a sound channel to output from TV. “Stereo” has been selected as the default.
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Getting started
4
Select “TV Audio Select” using K / L buttons, then
press ENTER button.
Option window will appear.
Setup > Channel Preset
Auto Preset
Manual Preset
Guide Channel Setting
TV Audio Select
VCR DV D
Stereo
Stereo
SAP
5
Select “Stereo” or “SAP” using K / L buttons, then
press ENTER button.
Stereo:
Outputs main-audio.
SAP: (Secondary Audio Program)
Outputs sub-audio. Refer to the item in “Glossary” on page 106 for more informa­tion.
2 3 4 5
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
1 6
Playback Setting
3
Select “Channel” using K / L /{ / B buttons, then press ENTER button.
Channel Preset menu will appear.
Setup > Channel Preset
Auto Preset
Manual Preset
Guide Channel Setting
TV Audio Select
22
VCR DV D
Stereo
6
Press SETUP button to exit.
Notes on TV channel audio
• When you record a TV program which has Stereo and Secondary Audio Programs on a DVD-RW/R or a tape, you have to select the TV channel audio (Stereo or SAP) beforehand. Only the selected channel audio will be recorded. Refer to the following table to check an appropriate setting.
Selected Broadcast Disc/tape Audio audio audio recording output
Stereo STEREO+SAP STEREO STEREO
STEREO STEREO STEREO MONO+SAP MONO MONO MONO MONO MONO
SAP STEREO+SAP SAP SAP
STEREO STEREO STEREO MONO+SAP SAP SAP MONO MONO MONO
• As can be seen in the above table, if your TV channel audio is set to SAP and the recorded TV program has Stereo and Secondary Audio Programs, you can only view the program in the sub-audio.
Set the clock before you try the
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
timer recording. If a Public Broadcasting Station (PBS) is available in your area, follow Auto Clock Setting below. If not, follow Manual Clock Setting on pages 24-25.
Auto Clock Setting
Make sure
•The antenna/cable TV connec­tions are correct.
• If this unit is connected to a Cable Box or Satellite Box, select the local PBS station on them to set the clock automatically.
Getting started
Clock setting
4
Select “Auto Clock Setting” using K / L buttons, then
press ENTER button.
Option window will appear.
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DVD
OFF
Auto
Auto Manual
Off
Before you start Connections
7
Getting started
2
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
2
Select “SETUP”using tons, then press ENTER button.
SETUP menu will appear.
Setup
{ / B
but-
5
If you do not know your PBS channel number, select “Auto” using K / L buttons, then press ENTER button.
If you know your PBS chan­nel number, select “Manual” using K / L buttons, then press ENTER button.
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
Enter your PBS channel number using Number or K / L buttons, then press
ENTER button.
VCR DVD
OFF
Set Channel No.
Auto
Auto
CH1
Manual
Off
3 4 5
Recording Playing discs
1 6
Editing
Changing the SETUP menu
VCR functions
Playback Setting
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
K / L / { / B
VCR DVD
Auto
ON
3
Select “Clock” using buttons, then press ENTER button.
Clock menu will appear.
6
Press SETUP button to exit.
7
Press POWER button to turn off the unit.
This unit will search for the time only when the power is off. Leave it off for several minutes to give this unit time to set the clock on the display of the front panel.
Note
• The clock may set itself auto­matically after you connect the antenna/cable signal to this unit and plug in the power cord. In this case, the current time will appear on the display of the front panel.
• If the current time is not dis­played or the displayed clock is not correct, set the clock manually.
Others
Español
Français
23
Manual Clock Setting
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Getting started
Clock setting (cont’d)
4
Select “Clock Setting” using K / L buttons, then press
ENTER button.
A clock setting window will appear.
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DVD
3
Select “Clock” using K / L / { / B buttons, then press
ENTER button.
Clock menu will appear.
Auto
ON
- - : - -
VCR DVD
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
- - - / - - / - - - - ( - - - )
Press ENTER button again.
Default date will appear.
5
Enter the date (month / day / year) using K / L buttons.
Press { / B buttons to move the cursor.
12 : 00AM
VCR DVD
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
JAN / 12 / 2004 (MON)
6
Enter the time (hour / minute) using K / L buttons.
Press { / B buttons to move the cursor.
09 : 24 AM
VCR DVD
Auto
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
JAN / 12 / 2004 (MON)
2 3 4 5 6
Note
Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds when you set the clock manu­ally.
1
24
Getting started
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
Clock setting (cont’d)
Before you start Connections
7
Press K / L buttons to select AM or PM, then press ENTER button.
Clock menu will appear, then the settings will be activated.
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DVD
Auto
ON
8
Press SETUP button to exit.
Although seconds are not displayed, they begin counting from zero.
7
8
Getting started
Recording Playing discs
When “Auto Clock Setting” is selected to “Auto” or “Manual”, change it to “OFF” as following steps.
Repeat steps (1) to (3) in “Manual Clock Setting”.
4
Select “Auto Clock Setting”
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
using K / L buttons, then press ENTER button.
Option window will appear.
VCR DVD
OFF
Auto
Auto Manual
Off
5
Select “OFF” using K / L buttons, then press ENTER button.
6
Press SETUP button to exit.
Editing
4
Changing the SETUP menu
5
6
VCR functions
Others
Español
Français
25
Setting the daylight sav­ing time
When Daylight Saving Time is ON, the clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October.
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
Getting started
Clock setting (cont’d)
4
Select “Daylight Saving Time” using K / L buttons,
then press ENTER button.
Daylight Saving Time options will appear.
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DVD
Auto
ON OFF
5
Select “ON” or “OFF” using K / L buttons, then press
ENTER button.
Choose “ON” when currently observing the daylight saving time.
2 3 4 5
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
1 6
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Clock” using K / L / { / B buttons, then press
ENTER button.
Clock menu will appear.
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
VCR DVD
Auto
ON
6
Press SETUP button to exit.
26
You can select the TV aspect ratio
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
to match the formats of what you are playing with the unit and your TV screen (4:3 standard or 16:9 widescreen TV). “4:3 Letter Box” has been select­ed as the default.
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Playback” using K / L / { / B buttons, then press ENTER button.
Getting started
Selecting the TV aspect ratio
Playback menu will appear.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
4
Select “TV Aspect” using K / L buttons, then press ENTER
button.
Option window will appear.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
16:9 Wide
4:3 Letter Box
8
4:3 Pan & Scan 16:9 Wide
English Original
OFF
ON
OFF
Refer to the Note on this page.
5
Select a desired option using K / L buttons, then press
ENTER button.
6
Press SETUP button to exit.
2 3
1
4
6
5
Note
If you have a standard TV:
Select “4:3 Letter Box”, so that black bars appear on the top and bottom of the screen. Select “4:3 Pan & Scan” for a full height picture with both sides trimmed.
If you have a widescreen TV:
Select “16:9 Wide”.
Before you start Connections
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
27
Recording
Information on DVD recording
Information
This unit can record to DVD-R and DVD-RW discs. When recording, you will need to select a recording format between Video mode and VR mode depend­ing on the disc format.The disc format for DVD-R is always “Video format,” so a recording format will be “Video mode”. On the other hand, when recording to DVD-RW, a recording format will be “Video mode” or “VR mode” because a disc format is available between “Video Recording format” and “Video format” for DVD-RW.
Logo Attributes
12cm, single-sided, single layer disc Approx. max. recording time (SEP mode):
DVD-RW
DVD-R
* This unit cannot record on the following discs.
• DVD-R General Ver 2.0/8x
• DVD-RW Ver 1.2/2-4x CPRM compatible
About Video mode and VR (Video Recording) mode
Video mode is the same recording format as DVD­Video discs purchased locally, so that you can play in most DVD players.To play in other DVD players, you will need to finalize (see page 44). If not final­ized, you can play, record additionally or edit discs recorded in Video mode with this unit. VR (Video Recording) mode is a basic recording format for DVD-RW.You can record and edit repeatedly.
DVD players with are capable of playing DVD-RW recorded in VR mode.
600 minutes (4.7GB)
12cm, single-sided, single layer disc Approx. max. recording time (SEP mode): 600 minutes (4.7GB)
Recording speed
Yo u can select a recording speed among 6 options, and the recording time will depend on the record­ing speed you select as follows.
Recording speed
XP (1H)
SP (2H)
LP (4H)
EP (6H)
SLP (8H)
SEP (10H)
Recording time *
60 min
120 min
240 min
360 min
480 min
600 min
Video/Sound Quality
* This table is designed for a new single-sided 12cm
disc as the standard.The recording time are esti­mates and actual recording time may differ.
* The audio and video quality is getting poorer as
the recording time becomes longer.
Restrictions on recording
You cannot record copy-protected video using this unit. Copy-protected video includes DVD-Video discs and some satellite broadcasts. If copy-protected material is encountered during a recording, the unit will pause or stop automatically and an error message will be displayed on-screen. Video that is “copy-once only” can only be recorded using a DVD-RW disc in VR mode with CPRM (see below). When recording a TV broadcast or through an external input, you can display copy control informa­tion on screen.
Disc type Disc format
Video mode
Video
DVD-RW
DVD-RW
DVD-RW
DVD-R
VR mode
VR
DVD-RW
DVD-RW
Video mode
DVD-R
DVD-R
28
Functions
Playing, limited recording, limited editing
Playing, recording, Original/Playlist editing
Playing, limited recording, limited editing
What is “CPRM”?
CPRM is a copy protection system with scram­ble system regarding the recording of “copy once” broadcast programs. CPRM stands for Content Protection for Recordable Media. This unit is CPRM compatible, which means that you can record copy-once broadcast pro­grams, but you cannot then make a copy of those recordings. CPRM recordings can only be made on DVD-RW discs formatted in VR mode, and CPRM recordings can only be played on players that are specifically compatible with CPRM.
Recording
Information on DVD recording (cont’d)
Before you start Connections
Information on copy control
Some satellite broadcasts include copy-protected information. For recording these, refer to the fol­lowing.
Disc type / format
ver.1.1
VR
DVD-RW
DVD-RW
DVD-RW
DVD-RW
DVD-R
DVD-R
ver.1.1 CPRM compatible
ver.1.1
Video
ver.1.1 CPRM compatible
ver.2.0
Recordable Not Recordable
Copy-free Copy-once
Note
• The audio and video quality gets poorer as the Recording time becomes longer.
This unit cannot record CD-R or CD-RW discs.
•DVD-R/RW and CD-R/RW discs recorded on a personal computer or a DVD or CD recorder may not play if the disc is damaged or dirty or if there is dirt or condensation on the unit’s lens.
• If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software pub­lisher for more detailed information.)
• Discs recorded in Video mode on this unit can­not record additionally using other DVD recorders.
Copy­prohibited
Making discs playable in other DVD player (Finalize)
After recording, you must finalize a disc in order to play on any other unit. (Refer to page 44.)
Playable
L - AUDIO - R
This Unit DVD player
Not Playable
After finalizing:
• Once DVD-R/RW (Video mode) is finalized, you cannot record additionally or edit.
•Even if DVD-RW (VR mode) is finalized, you can record additionally to or edit.
• When DVD-R/RW (Video mode) is finalized, title menu will be created automatically.
To play in other DVD players, finalize discs record­ed on this unit with the following condition.
Disc type Mode
DVD-R
ver.2.0
DVD-RW
ver.1.1 ver.1.1 CPRM compatible
Video mode
Video mode VR mode
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
29
Recording
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Formatting a disc
Settings for the recording format to a blank disc
Video
DVD-RW
DVD-RW
When inserting a blank disc, the unit starts to initialize the blank disc. After that, you can record to the disc with the recording format selected in SETUP menu. You are allowed to set a specified time for chapter marks.
VR
DVD-RW
DVD-RW
3
Select “Recording” using K / L / { / B buttons, then press
ENTER button.
Recording menu will appear.
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode
DVD
Video mode
10 minutes
VCR DVD
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
4
Select “DVD-RW Recording Format” using K / L buttons,
then press ENTER button.
Option window will appear.
2 3
1
4 5
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode VCR DVD
Video mode DVD Player Compatibility mode. VR mode Editing possibility mode.
DVD
Video mode
VR mode
VR mode
10 minutes
Video mode has been selected as the default.
5
Select “Video mode” or “VR mode” using K / L buttons,
then press ENTER button.
The recording mode will be set.
Note
• The recording format setting is effective only for DVD-RW discs.You cannot change the recording format on a DVD-R disc. DVD-R discs will always be in Video mode.
You cannot mix two for­mats on one DVD-RW disc. When you load a disc once recorded before, the recording format cannot be changed even if you change it in SETUP menu.
• When inserting a blank DVD+R or DVD+RW disc, the error message ("Disc Error") will appear.This unit is not compatible with a DVD+R/RW disc.
• PLAYLIST will be created automatically when recording
on DVD-RW in VR mode.
30
6
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Select “Auto Chapter” using K / L buttons, then press
ENTER button.
Option window will appear.
Recording
Formatting a disc (cont’d)
Before you start Connections
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode VCR DVD
VR mode
OFF 5 minutes
10 minutes
10 minutes 15 minutes 30 minutes 60 minutes
“10 minutes” has been selected as the default.
7
Select a desired time option using K / L buttons, then
press ENTER button.
Chapter marks will be put as you specified.
8
Press SETUP button to exit SETUP menu.
DVD
6 7
Getting started
Recording Playing discs
8
Editing
Changing the SETUP menu
VCR functions
Note
• The time for chapter marks is not accurate in Video mode.
Others
Español
Français
31
Reformatting a disc
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Video
DVD-RW
DVD-RW
If you are using a DVD-RW disc, by default it will be Video mode. You can change this to VR mode from SETUP menu.
VR
DVD-RW
DVD-RW
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
2
Select “DISC” using { / B but- tons, then press ENTER button.
DISC menu will appear.
Recording
Formatting a disc (cont’d)
4
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Option window will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Yes No
Are you sure?
Yes No
* VR mode only
5
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Formatting will start.
2 3
1
4 5
Disc
Edit
Format
Finalize
Disc Protect OFF ON
* VR mode only
3
Select “Format” using K / L buttons, then press ENTER
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Yes No
button.
Option window will appear.
* VR mode only
Formatting
6
Formatting is complete.
100% will be indicated.
100%
Formatting
This operation may take a while to be completed.
58%
Note
• When you reformat the disc, the contents of the disc will be erased.
• If you want to cancel format
at step 5, select “No”.
32
Recording
DVD
Basic recording
Before you start Connections
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
Follow the steps below to record TV programs.
First:
1
Turn on the unit and load a recordable disc.
Make sure that the TV input is set on the unit.
This operation may take a while to be recognized.
2
Select a recording speed using REC SPEED button.
SP 2:01 Rem.
4
Select a desired channel to record using CH K / L but-
tons or number buttons.
CH 1
5
Press REC/OTR button to start recording.
I mark will be displayed for 5 seconds.
2
6
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
CLOSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
OPEN/
DEF
MNO
WXYZ
4
Getting started
Recording Playing discs
5 4
5
Refer to “Recording speed” on page 28.
3
Make sure that the recording format is set to the desired mode.
Refer to “Formatting a disc” on pages 30-32.
When a DVD-RW disc is loaded:
You can choose Video mode or VR mode from SETUP menu. “Video mode” has been selected as the default. Refer to “Settings for the recording format to a blank disc” on pages 30-31.
When a DVD-R disc is loaded:
DVD-R discs will always be in Video mode.
I
To pause the recording, press PAUSE F button. Press REC/OTR
button to restart the recording.
6
Press STOP C button to stop the recording.
This operation may take a while to be completed.
Note
• Recording starts immediately and continues until the disc becomes full or you stop recording.
• When the clock setting has not been made, the space for a date and time of title names in the original or playlist will be blank.
You cannot mix two for­mats on one DVD-RW disc. When you load a disc once recorded before, the recording format cannot be changed even if you change it in SETUP menu.
•You cannot change the recording speed during the REC pause mode.
•You can change a channel during the REC pause mode.
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
33
Recording
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Basic recording (cont’d)
Checking the recording picture quality
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
You can confirm the recording pic­ture quality with the recording speed you have selected before attempting to record to a DVD disc.
First:
DVD
VR
DVD-RW
DVD-RW
2
Press REC MONITOR button again to exit.
1
While the unit is in STOP or REC with a DVD disc to record inserted, press REC MONITOR button.
The TV program will be on the screen in the recording picture quality with the recording speed you have selected.
Rec Monitor
If you want to change the recording speed, press REC SPEED button repeatedly.
The recording speed will be changed as you press the button as shown. Refer to “Recording speed” on page 28.
•You cannot change the record­ing speed during recording.
XP SP LP
1 2
1
CH 18
XP
34
EPSLPSEP
Note
•You cannot check the record­ing sound quality with the
Rec monitor function.
Recording
DVD
One-touch timer recording
Before you start Connections
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
This is a simple way to set the recording time in blocks of 30 minutes. Check that the disc you are recording onto has enough space for the time you set. When the recording finishes the recorder automatically goes into standby.
First:
1
Turn on the unit and load a recordable disc.
Make sure that the TV input is set on the unit.
This operation may take a while to be recognized.
2
Select a recording speed using REC SPEED button.
Refer to "Recording speed" on page 28.
4
Select a desired channel to record using CH K / L but-
tons or number buttons.
5
Press REC/OTR button, then press REC/OTR button repeatedly until a desired recording time (30 minutes to 8 hours) appears on the TV screen.
Recording will start.
0:30
I
0:30
(Normal Recording)
1:00
2
5
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
CLOSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
OPEN/
DEF
MNO
WXYZ
Getting started
Recording Playing discs
5 4
Editing
3
Make sure that the recording format is set to the desired mode.
Refer to "Formatting a disc" on pages 30-32.
When a DVD-RW disc is loaded:
You can choose Video mode or VR mode from SETUP menu. "Video mode" has been selected as the default. Refer to pages 30­31 "Settings for the recording for­mat to a blank disc."
When a DVD-R disc is loaded:
DVD-R discs will always be in Video mode.
8:00 7:30
When the unit reaches the speci­fied time, it will turn off automati­cally.
To cancel the one-touch timer recording within the specified time, press STOP C button.
This operation may take a while to be completed.
Note
• The remaining recording time will appear on the display panel during an OTR. Press DISPLAY button to see it on the TV screen.
•You cannot pause an OTR.
• The unit will turn off auto­matically under the conditions following.
1)No space remained on the
disc.
2)When a power failure
occurs.
•If OTR is finished in DVD during playback or REC mode in VCR, the DVD will be in STOP mode and the VCR
keeps the current mode.
Changing the SETUP menu
VCR functions
Others
Español
Français
35
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
DVD-R
DVD-R
VCR
VCR
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
You can program the unit to record up to 8 programs, up to a year in advance. Daily or weekly program recordings are also available.
• Be sure to set the clock before making a timer programming.
• Insert a recordable disc or a tape with a record tab.
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Recording
Timer recording
4
Select “Timer Programming” using K / L buttons, then
press ENTER button.
Timer Programming list will appear.
Setup > Recording > Timer Programming
Date Start End CH Speed
- - -
- - -
- - -
DVD VCR
5
Select the program which is not set up using K / L but-
tons, then press ENTER but­ton.
You can choose the timer programming menu by press­ing VCR Plus+ button twice. In this case, continue with step 5.
2 3
1
4
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
3
Select “Recording” using K / L / { / B buttons, then press
ENTER button.
Recording menu will appear.
36
Playback Setting
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode
Video mode
10 minutes
VCR DVD
DVD
6
Enter the date using K / L buttons, then press B button.
Setup > Recording > Timer Programming
Date Start End CH Speed
JAN / 01
- - -
- - -
- - -
- - : - -
- - : - -
AM
AM
CH8 DVD
DVD VCR
e.g. January 1st
JAN/01
When pressing L button at the current date, timer recording
Daily
MON-SAT
MON-FRI
SAT
FRI
SUN
DEC/31
mode will change as follows.
7
Enter the time to start and to end using K / L buttons, then press B button.
Setup > Recording > Timer Programming
Date Start End CH Speed
JAN/12
- - -
- - -
10 :00
- - : - -
PM
AM
CH8 DVD
DVD VCR
5 6 7
Note
If you have not set the clock yet:
A clock setting window will appear after step 4. Continue with the step 4 in “Auto Clock Setting” on page 23 or “Manual Clock Setting” on page 24 before making a timer programming.
•Press { or B buttons to move the cursor to the left and the right in the timer
programming menu.
Recording
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
SEARCH
MODE
CM SKIP
ZOOM
Timer recording (cont’d)
Before you start Connections
8
Select the channel number to record using K / L buttons, then press B button.
Setup > Recording > Timer Programming
Date Start End CH Speed
JAN/12
- - -
10:00
10:30
PM
To r ecord from external input, L1
PM
DVD VCR
CH8 DVD
10
Select a recording speed using K / L buttons.
Setup > Recording > Timer Programming
Date Start End CH Speed
JAN/12
10:00
PM
- - -
10:30
Refer to “Recording speed” on page 28 for DVD or page 98 for VCR.
PM
CH8 DVD
DVD VCR
or L2.
9
Select a recording media using K / L buttons, then press B button.
Setup > Recording > Timer Programming
Date Start End CH Speed
JAN/12
- - -
10:00
10:30
PM
•To record on to a tape, select VCR.
•To record on to a disc, select DVD.
PM
DVD VCR
CH8 DVD
11
Press ENTER button when all information required is entered.
Your program setting will be stored.
•To set another program, repeat steps 5 to 11.
•To exit, press SETUP button.
12
Press POWER button to turn off.
indicator will appear on the
front display.
Checking, canceling, or correcting the timer programming information
1
Press POWER button so that
indicator disappears from
the front display.
4
To clear the timer programming, select your desired program using K / L buttons, then press CLEAR/C.RESET button.
2
Press VCR Plus+ button twice.
Timer Programming list will appear.
Setup > Recording > Timer Programming
Date Start End CH Speed
3
Check the information on the list you will need.
On the front panel of the main unit, press STOP CCbutton to stop the disc recording or STOP/EJECT STOP CCbutton on the remote control is not effective.
JAN/12
- - -
To stop the timer recording in process
10:00
10:30
PM
PM
CH8 DVD
DVD VCR
1H
To correct the timer program­ming, select your desired pro­gram using K / L buttons, then press ENTER button.
Next, correct the timer programming using K/L/{/B buttons.
Finally, press ENTER button again.
5
Press VCR Plus+ button to exit.
6
Press POWER button to return to the timer standby mode.
CC AA
to stop the tape recording.
12
1H
Getting started
8 9
10 11
Note
• After step 12, the unit will be turned on automatically 2 minutes (For VCR recording, 10 seconds) in advance of the recording time to start and waits to start.Then the recording will start at the
recording time you set.
1
Recording Playing discs
Editing
6 2
Changing the SETUP menu
5
4
VCR functions
4
Note
•Press VCR Plus+ button to check the timer programming in process. When the timer recording is in process, that program will be red highlighted. In this case, you cannot select any other
program.
Others
Español
Français
37
Recording
Timer recording (cont’d)
Hints for timer recording
If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a disc is not on the tray, the DVD indicator on the front panel flashes and timer recording cannot be performed. Please insert a recordable disc.
• If a tape with a record tab is not in the cassette compartment, the VCR indicator on the front panel flashes and timer recording cannot be performed. Please insert a recordable tape.
• When all the timer recording is completed, the indicator flashes.To play or eject the recorded disc (or the tape), press POWER button first and then press PLAY B or OPEN/CLOSE A (or STOP/EJECT CA) button.
• The timer recording is not performed in DVD and VCR at the same time. If you set two programmings with the same channel and time both in DVD and VCR, the programming that has priority will be recorded.
• During timer recording or timer standby ( indicator is on the front display), any operations on the unit will not be available.To make these operations available, cancel the timer recording or timer standby first ( indicator disappears).
• To cancel the timer standby mode, press POWER button.
• When the Start and the End time are the same, the length of the recording will be set for 24 hours.When the disc reaches at the end during the recording, the unit turns itself off.
• When the programmed Start and End time are earlier than the current time, the recording will be set on the same date in the next year. If your programmed Start time for DVD recording is within 2 minutes from the current time, the power will turn on for recording
• standby right after you turn the power off. For a videotape recording, the power will turn on shortly before the Start time.
• If a videotape ends during timer recording, the unit will stop, eject the videotape, and turn itself off.
• When two or more programmings are overlapped,“Overlap” will be displayed.
The priority of overlapped settings
This unit records the programs according to priority if the timer programmings are overlapped.The timer programming set previously has priority. A timer recording of lower priority will be canceled, start from the middle or stop on the way. Check the overlapped timer programmings and change the priority if necessary.
A programming set previously has priority
When the starting time is the same:
A program set previously (PROG.A) has priority.
ex.1
PROG. A
PROG. B
Actual recording
PROG. A PROG. B
When some programming have been made at the end time of the programming currently being recorded:
A program set previously (PROG. B) has priority.
ex. 2
PROG. A
PROG. B
PROG. C
Actual recording
PROG. A PROG. B
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to be recorded.
PROG. A
PROG. B
Actual recording
PROG. B PROG. A
Note for DVD timer recording
• When the recording time of two programs are over­lapped, or the End time of a program and the Start time of another is the same, the first 20-90 sec­onds of the subsequent program will be cut off.
38
Example: When the end time of the programming currently being recorded and the starting time of the one to be recorded sequentially are same:
PROG. A
PROG. B
Actual recording
When the recording time is entirely overlapped:
PROG. A will not be recorded.
PROG. A
PROG. B
Actual recording
PROG. BPROG. A
The first 20-90 seconds will be cut off.
PROG. B
Recording
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Timer recording using VCR Plus+®system
Before you start Connections
DVD-R
DVD-R
VCR
VCR
Video
DVD-RW
DVD-RW
DVD-RW
DVD-RW
The VCR Plus+ system lets you set timer recordings very simply. Just enter the PlusCode number listed in the TV program guide. The date, time, and channel for the TV program to record will set automatically. Before setting timer recording using VCR Plus+ system, read “Guide channel setting” on pages 20-21.
1
In stop mode, press VCR Plus+ button.
VCR Plus+ setting menu will appear.
Screen:
VCR Plus+
Please enter a Plus Code No.
- - - - - - - - -
Note:
When eight timer recordings have been scheduled, the Timer Programming list will appear instead.
2
Enter the PlusCode number correctly using number but­tons.
3
Press ENTER button.
The Timer Programming list will
VCR Plus+
Please enter a Plus Code No.
1 2 3 4 - - - - -
VR
appear.
When the Guide channel has not been assigned:
6
The CH area has been selected, then enter the channel number to record using
Setup
- - -
- - -
- - -
- - -
- - -
- - -
- - -
K / L buttons
> Recording > Timer Programming
Date Start End CH Speed
10:30PM10:00PMJAN/12
.
DVD VCR
1H
DVD
1 5
2
Getting started
3 4
Recording Playing discs
When the Guide channel has been assigned:
The programming you made with VCR Plus+ system is hilighted to check.
Setup
> Recording > Timer Programming
Date Start End CH Speed
- - -
- - -
- - -
- - -
- - -
- - -
- - -
• If you want to change the set-
ting, use K / L / { / B but­tons.
DVD VCR
1H
DVD
CH810:30PM10:00PMJAN/12
Note
•Press { button to erase the latest number entered incor­rectly at step 2.
•Press CLEAR/C.RESET button to erase all numbers entered incorrectly at step 2.
Editing
Changing the SETUP menu
• If you enter an incorrect
4
Press ENTER button after you entered or confirm the information.
Your VCR Plus+ program setting will be stored.
PlusCode number at step 2 or the programming is not available, the error message “Code Error!” will appear. Enter the correct PlusCode number.
Remember:
VCR functions
If your cable box or satellite
5
Press VCR Plus+ button to exit.
box is connected as in “Connection A” on page 14, TV Channel number must be
Others
channel 3 or 4 for every a
6
Press POWER button to return to the timer standby mode.
guide channel number. Then, set your cable box or satellite box to the channel you want to record; leave your cable
Español
box or satellite box on for
the timer recording.
Français
39
Recording
Settings for an external source
Connection to an external source
Connect the external source properly to the unit by using input jacks either LINE2 (Front) or LINE1 (Rear). When you want to record to a tape, use either DVD/VCR VIDEO IN jack (Rear) or VIDEO input jack (Front). S-VIDEO input is useful only in DVD mode. Use commercially available S-Video or Video cable and an Audio cable for this connection.
S- VIDEO
OUTPUT
VIDEO
AUDIO
Another source
RL
(VCR camcorder etc.)
OUTPUT
VIDEOS -VIDEO AUDIO
LR
or
S-Video
cable
Video
cable
To LINE 2 IN To LINE 1 IN
POWER
REW F.FWD RECORD
PLAY
STOP/EJECT
Audio cable
S-VIDEO
VIDEO L - AUDIO - R
OPEN/CLOSE
SELECT
CHANNEL
DUBBING
STOP PLAY RECORD
S-VIDEO
DVD
VCR
VIDEO L - AUDIO - R
Front of this unit Rear of this unit
1. Press SETUP button to display SETUP/DISC menu.
2. Select “SETUP” using
{ / B buttons, then
press ENTER button.
3. Select “Select Video” using K / L
, then press ENTER button.
tons
Setup > Select Video
L1 (Rear)
L2 (Front)
Video In
Video In
4. Select “L2 (Front)” using K / L
/ { / B but-
DVD
buttons, then
press ENTER button.
or
or
S-Video
cable
Video
cable
DVD
S-VIDEO
IN
OPTICAL
Audio cable
DVD/VCR
AUDIO IN
L
R
VIDEO IN
DVD/VCR
COMPONENT
COMPONENT
ANTENNAINAUDIO OUTAUDIO IN
VIDEO OUT
VIDEO OUT
DVD
DIGITAL
AUDIO OUT
COAXIAL
LY
AUDIO OUT
L
R
L
S-VIDEO
P
B/
R
R
CB
IN
VIDEO OUTVIDEO IN
OUT PR/ C
R
OUT
1. Press SETUP button to display SETUP/DISC menu.
2. Select “SETUP” using
{ / B buttons, then
press ENTER button.
3. Select “Select Video” using K / L
, then press ENTER button.
tons
Setup > Select Video
L1 (Rear)
L2 (Front)
Video In
Video In
4. Select “L1 (Rear)” using K / L
/ { / B but-
DVD
buttons, then
press ENTER button.
Video In
Video In S-Video In
Video In
DVD
using K /
Setup > Select Video
L1 (Rear)
L2 (Front)
5.
Select the input jack type to connect
buttons,
L
then press ENTER button.
If you want to use S-VIDEO input, select “S-Video In”. If you want to use VIDEO input (Composite), select “Video In”.
Setup > Select Video
L1 (Rear)
L2 (Front)
DVD
Video In
S-Video In
40
Video In
Video In S-Video In
Video In
DVD
Setup > Select Video
L1 (Rear)
L2 (Front)
5.
Select the input jack type to connect using
buttons
L
, then press ENTER button.
If you want to use S-VIDEO IN, select “S-Video In”. If you want to use VIDEO IN (Composite), select “Video In”.
Setup > Select Video
L1 (Rear)
L2 (Front)
DVD
S-Video In
Video In
K /
Recording
DVD
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Settings for an external source (cont’d)
Recording from an external source
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
Before recording from an external source, see the instructions for the connection on page 40.
1. Turn the TV and the unit on, and be sure to select the input of the TV to which the unit is connected.
VR
DVD-RW
DVD-RW
VCR
VCR
1
Before you start Connections
2
2. When y
ou want to record to the disc: Press:
Press OPEN/CLOSE A button to open the disc tray, then place the disc to record properly.
This operation may take a while to be recognized.
When y
ou want to record to a tape: Press:
VCR
Insert the tape with a record tab into the cassette com­partment.
3. Select the input of the unit which the external equipment is connected. (L2 or L1)
•To use the input jacks on the back of this unit, select “L1” position by
pressing [0],[0],[1] on the remote control or the CH K / L buttons.
•To use the input jacks on the front of this unit, select “L2” position
by pressing [0],[0],[2] on the remote control or the CH K / L but­tons.
4. Select a recording speed using REC SPEED button.
“Recording speed” on page 28 for DVD or page 98 for VCR.
XP SP LP
SP SLP
SEP
or disc:
DVD mode
5.Press REC/OTR button on the unit to start recording.
6.Press PLAY button on the external source to record from.
7.F
EPSLP
VCR mode
Press STOP C button on the unit to stop recording.
Refer to
4
7
Getting started
3
Recording Playing discs
5 3
Editing
Changing the SETUP menu
VCR functions
This operation may take a while to be completed. F
or tape:
Press STOP/EJECT CAbutton on the unit to stop record­ing.
Others
Español
Français
41
DVD-R
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
DVD-R
VCR
VCR
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
You can copy a DVD disc to a videotape or copy a videotape to a DVD disc.This function will be possible only if the DVD disc or the tape is not copy protected. Before starting this function, pre­pare for the recording on the DVD-R/RW disc or the videotape. Refer to pages 33-34, 98.
Make sure:
• Insert a disc and a tape with a
record tab.
Note for recording to a tape:
• The tape's record tab is intact.
• The videotape is long enough to
record the DVD disc.
Note for recording to a disc:
• The DVD disc is satisfied with
the recording status. Refer to pages 28-29.
Recording
Dubbing Mode
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Recording” using K / L / { / B buttons, then press
ENTER button.
Recording menu will appear.
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode
DVD
Video mode
10 minutes
VCR DVD
2 3
1
4
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
4
Select “Dubbing Mode” using K / L buttons, then press
ENTER button.
Option window will appear.
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode
VCR DV D
Video mode
OFF
VCR DVD
Note
For VCR to DVD duplication:
• After starting VCR to DVD duplication, the picture may be distorted because of the auto tracking function. This is not a malfunction. Be advised to playback the tape until the picture is stabilized, then set the starting point which you wish to start recording, and start VCR to
DVD duplication.
42
Recording
DVD
VCR
VCR
REW F.FWD RECORD
CHANNEL
SELECT
STOP PLAY RECORD
DUBBING
OPEN/CLOSE
PLAY
STOP/EJECT
VCR
DVD
Dubbing Mode (cont’d)
Before you start Connections
VCR to DVD
5
Select “VCR ⇒ DVD” using K / L buttons, then press
ENTER button.
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode
VCR DV D
Video mode
OFF
VCR DVD
VCR DVD VCR DVD
6
Press SETUP button to exit SETUP menu.
Make sure to select a recording speed using REC SPEED button.
Press:
7-a
Press PLAY B button on the unit, and then press PAUSE button at the point you wish to start recording.
8
Press DUBBING button on the front of the unit.
VCR to DVD duplication will start.
9-a
Press
STOP C
unit or STOP the remote control to stop the recording.
button on the
C button on
DVD to VCR
5
Select “VCR ⇐ DVD” using K / L buttons, then press
ENTER button.
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
Dubbing Mode
VCR DV D
Video mode
OFF
VCR DVD
VCR DVD VCR DVD
6
Press SETUP button to exit SETUP menu.
Press:
Make sure to select a recording speed using REC SPEED button.
Press:
7-b
Press PLAY B button on the unit, and then press PAUSE button at the point you wish to start recording.
8
Press DUBBING button on the front of the unit.
DVD to VCR duplication will start.
9-b
Press STOP/EJECT CAbut- ton on the unit or STOP C button on the remote control to stop the recording.
.@/:
GHI
REC
CLOSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
OPEN/
DEF
MNO
WXYZ
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
+
PQRS
MONITOR
5
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
DVD
REC/OTR
CH
SETUP
6
FWDREW
RETURN
VCR
SLOW
SKIP
9
7
7-b7-a
9-b
Note
• When you turn off the unit after setting the Dubbing Mode to , the setting will be set to
automatically.
• Dubbing Mode is available only if the tape or disc is not copy protected.
•You cannot change the output mode during VCR to DVD or DVD to VCR duplication.
For VCR to DVD duplication:
•The playback sound mode is followed by the setting of VCR playback sound mode on page 100. Set the playback sound mode to which you wish to record to the DVD.
8
9-a
43
Getting started
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
Recording
Finalizing the discs
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
You will need to finalize discs recorded in Video mode to play in other DVD players. Finalizing may take several min­utes up to an hour. (A disc recorded in Video mode can take up to 15 minutes.A disc recorded in VR mode can take up to 60 minutes.) A shorter recording period on the disc will require a longer time period for finalization. Do not unplug the power cord during finalization. Details are on pages 28-29.
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Yes No
* VR mode only
4
Select “Yes” using { / B but- tons, then press ENTER button.
Finalizing will start.
Finalizing
To cancel finalizing, press STOP C button.
Do you want to cancel?
Yes No
58%
REC
MONITOR
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
ZOOM
CLEAR/
C.RESET
2
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
DVD
REC/OTR
CH
SETUP
1
FWDREW
3 4
RETURN
VCR
SLOW
SKIP
4
Note
• Finalizing discs in Video mode automatically creates title menus.
• Once you have finalized a disc recorded in Video mode, you cannot edit or record any­thing else on that disc. Discs recorded in VR mode can still be recorded and edited on this unit even after finalized.
• When you insert a DVD-RW disc finalized with this unit, “Undo Finalize” will appear instead of “Finalize”.
2
Select “DISC” using { / B buttons, then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
* VR mode only
3
Select “Finalize” using K / L buttons, then press ENTER button.
Option window will appear.
44
Finalizing
Select “Yes” using
{ / B buttons
58%
then press ENTER button.
Finalizing is cancelled, then the unit will be in stop mode.
5
Finalizing is complete.
Finalizing
This operation may take a while to be completed.
100%
Disc
Edit
,
Format
Undo Finalize
To r elease the finalizing for the disc, select “Undo Finalize” at step 3.
• If appear when pressing STOP buttonat step 4, you cannot cancel finalizing because the finalizing has been in certain progress.
• When selecting “No” at step 4, press ENTER or RETURN button, finalizing will be con­tinued.
•You cannot cancel finalizing the DVD-R disc once it has started.
*DONOT power off during
finalizing, this will result in
malfunction.
VR
Disc
Edit
Format
Finalize
Disc Protect ON OFF
Yes No
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
DVD-RW
DVD-RW
To prevent accidental recording, editing or erasing the titles, you can protect them from DISC menu.
Recording
Setting a disc to protect
3
Select “Disc Protect OFF ON” using K / L buttons,
then press ENTER button.
Option window will appear.
Before you start Connections
1
Press SETUP button to dis­play SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Setup Menu
2
Select “DISC” using { / B buttons, then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Yes No
4
Select “Yes” using { / B but- tons, then press ENTER but­ton.
A disc will be protected.
Writing to Disc
This operation may take a while to be completed.
58%
2 3 4
Note
• The Disc Protect setting is available only when a disc with VR mode is inserted.
•You can select only Disc Protect Menu when a pro­tected disc is inserted.
To cancel the disc protect:
• When you insert a disc pro­tected with this unit,“Disc Protect ON OFF” will appear instead of “OFF ON”.
To r elease the protect for the disc, select “Disc Protect ON OFF” at step 3, then select
“Yes”.
Getting started
1
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
45
Playing discs
)
Start Rec. Stop/Start Stop Rec.
Title 1 Title 2
Chapter 1 Chapter 1Chapter 2 Chapter 3 Chapter 2
Information on DVD play
Before you attempt to play DVD discs, read the following information.
Playable discs
This unit is compatible to play the following discs. To play a DVD, make sure that it meets the require­ments for Region Codes and Color Systems as described below. Discs that have the following logos will play on the unit. Other Disc types are not guar­anteed to play.
LogoDisc
DVD VIDEO
DVD-RW (VIDEO/VR mode)
DVD-R (VIDEO mode)
CD-DA (AUDIO CD)
CD-R (CD-DA FORMAT, MP3 files)
CD-RW (CD-DA FORMAT, MP3 files)
Region codes
This unit has been designed to play DVD discs with Region One (1). DVDs must be labeled for ALL regions or for Region 1 in order to play on this unit. You cannot play DVDs that are labeled for other regions. Look for the symbols below on your DVDs. If these region symbols do not appear on your DVD, you cannot play that DVD in this unit.
The number inside the globe refers to region of the world. Region 1 represents the United States, Canada, Bermuda, the U.S.Virgin Islands and small regions near Australia. A DVD labeled for a specific region can only play on the unit with the same region code.
Hint for DVD playback
The contents of DVD disc are generally divided into titles.Titles may be further subdivided into chapters.
Color systems
DVDs are recorded in different color systems throughout the world.The most common color sys­tems are NTSC (which is used primarily in the United States and Canada), PAL and SECAM. This unit uses NTSC, so DVDs you play must be recorded in the NTSC system.You cannot play DVDs recorded in other color systems.
Guide to displays
First:
DVD
Press DISPLAY button to call up the display menu.This menu will give you the information on the playing disc. Some operations are available while disc is playing.
4
11 00:00:00
5
1
DVD-RW
Video mode
SP 1:25 Rem.
CH 1
1. Indicates a disc type and a
format mode.
2. Indicates a recording speed
and possible recording time left.
3. Indicates a current channel
number and an audio status of the program.
4. Indicates a title number, chap-
ter number and the time
2
elapsed of disc play.
3
5. Each icon means:
: Search
: Audio
: Subtitle
: Angle (except VR mode
: Repeat
: Marker
: Noise Reduction
: Zoom
: Spatializer
46
Playback
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Playing discs
Basic playback
Before you start Connections
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
1
Press POWER button, then press DVD button.
When you are playing a DVD, turn the TV on and be sure to select the input to which the unit is con­nected.
2
Press OPEN/CLOSE A but- ton to open the disc tray.
The disc tray will open.
3
Place the disc onto the disc tray with its label facing up and make sure to align the disc to the disc tray guide.
VR mode:
Original
1 1 32
JAN/1 12:00AM
JAN/1 3:00AM
JAN/1 1:00AM JAN/1 2:00AM
54
JAN/1 4:00AM
MENU / LIST button
Playlist
1 1 32
JAN/1 12:00AM
JAN/1 3:00AM
JAN/1 1:00AM JAN/1 2:00AM
54
JAN/1 4:00AM
5
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Playback will start.
1
4 5
6
2 6
Getting started
4
Recording Playing discs
1
Editing
4
Press TOP MENU button to
This operation may take a while to be recognized.
display the title menu.
You can change “Original” or “Playlist” of VR mode using MENU / LIST button.
Video mode:
Title List
JAN/1 12:00AM
JAN/1 3:00AM
1 1 32
JAN/1 1:00AM JAN/1 2:00AM
54
JAN/1 4:00AM
disc tray guide
6
Press STOP C button to stop playback.
To eject the disc, press OPEN/CLOSE A button to open
the disc tray, then remove the disc before turning off the unit.
Note
•For DVD-R (Video mode) and DVD-RW (Video mode) discs which are already final­ized, a title list will be dis­played instead of thumbnails.
1
Title Menu
2
3
4
5
6
7
8
•You can resume play from where you stopped playing the disc. (Resume play) Refer to page 51 for details about resume play.
• Some discs may start playing
automatically.
XP
CH9612:24AMJAN/1
Changing the SETUP menu
VCR functions
Others
Español
Français
47
Playing discs
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
SPACE
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
ZOOM
Basic playback (cont’d)
DVD-V
DVD-V
CD
CD
MP3
MP3
1
Press POWER button, then press DVD button.
When you are playing a DVD or an audio CD, turn the TV on and be sure to select the input to which the unit is connected.
2
Press OPEN/CLOSE A but- ton to open the disc tray.
The disc tray will open.
3
Place the disc onto the disc tray with its label facing up and make sure to align the disc to the disc tray guide.
For MP3 playback
4
Press PLAY B button to start playing.
Playback will start.
If you are playing a DVD-Video disc, a menu may appear. Refer to pages 49-50 for details about a disc menu.
5
Press STOP C button to stop playing.
1
5
Note
• Some discs may start playing
automatically.
2
1
4
1
In stop mode, press TOP MENU button to call up the MP3 menu.
List of MP3 Files
DISC NAME
FOLDER NAME 1 FOLDER NAME 2 FOLDER NAME 3 FOLDER NAME 4 FOLDER NAME 5 FOLDER NAME 6 1 FILE NAME 1 2 FILE NAME 2
•To exit the menu, press TOP
2
Press KK/ LLbuttons to select a desired folder (group) or track, then press ENTER button.
When selecting track:
Playback will start.
When selecting the f
The files in the folder will appear. Press K or L button to select the track you want, then press button.
48
MENU button again.
1/2
older:
ENTER
•When selecting a folder, press
PLAY B, ENTER or B button to go to the lower hierarchy.
•Press s button or RETURN button to go to the previous hierarchy.
•Press STOP C button to return to the first item.
Hints for MP3 files:
•Folders are known as Groups, files are known as Tracks.
Folders are accompanied by icon.
MP3 files are accompanied by icon. Reproduction will start from the selected track and go to the next one in turn.
The system can recognize up to 255 groups (or folders) and up to 255 tracks.
The name of the group and track can be displayed in up to 32 char­acters. Unrecognizable characters will be replaced with asterisks.
• If there are no files in the folder, “No Files” will be displayed.
This unit recommends the files recorded under the following cir­cumstances:
Sampling frequency: 44.1kHz or 48kHz.
Constant bit rate: 112kbps - 320kbps.
1
2
2
2
Note
• The audio source of MP3 files cannot be recorded as digital sound by an MD or DAT deck.
• Files whole extension other than “.mp3 (MP3)” will not be listed in the MP3 menu.
• Some unplayable folders or tracks may be listed in the MP3 menu due to the recording status.
Playing discs
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Basic playback (cont’d)
Playing discs using the disc menu
DVD-V
DVD-V
A DVD disc contains a disc menu that describes the contents or allows you to customize the play­back. For example, the menu may offer choices for subtitle lan­guages, special features, or chapter selection. Sometimes these are displayed automatically when you start play­back, otherwise only appear when you press MENU/LIST button.
First:
DVD
1
Press MENU/LIST button.
The DVD main menu will appear.
If the feature is not available, may appear on the TV screen.
2
Select an item using K / L / { / B buttons, then press
ENTER button to confirm.
Continue this step to set up all the features you want or to start playing the disc from the menu.
MENU/LIST button:
Displays a DVD disc menu which varies with the disc and may be the same as the ‘Title menu.’
K / L / { / B buttons:
Moves the cursor around screen.
Enter button:
Selects the currently highlighted menu option.
Number buttons:
Selects a numbered menu option (some discs only). Press ENTER button after.
1 2 3
Before you start Connections
2
Getting started
2
Recording Playing discs
Editing
3
Press MENU/LIST button to exit the menu.
Note
• Menus vary among discs.
Refer to the information accompanying the disc for details.
Changing the SETUP menu
VCR functions
Others
Español
Français
49
Playing discs
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Basic playback (cont’d)
Playing discs using the title menu
DVD-V
DVD-V
Some DVDs have a title menu, which lists the titles available on them. It helps you to start play­back at a specific title.
First:
DVD
2
Select a title to play using the K / L / { / B buttons, then
press ENTER button.
Playback will begin at the title you selected.
2
1
Press TOP MENU button.
The title menu will appear.
If the feature is not available, may appear on the TV screen.
TOP MENU button:
Displays the ‘Title menu’ of a DVD disc which varies with the disc.
K / L / { / B buttons:
Moves the cursor around screen.
Enter button:
Selects the current highlighted menu option.
Number buttons:
Selects a numbered menu option (some discs only). Press ENTER button after.
3
Press TOP MENU button to exit the title menu.
2
1 2 3
50
Note
• The TOP MENU button will
not always be active with all DVDs.
• Menus vary among discs.
Refer to the information accompanying the disc for
details.
Resume play
SPACE
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
ZOOM
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
DVD-V
DVD-V
DVD-RW
DVD-RW
DVD-R
DVD-R
VR
CD
CD
You can resume play from where you stopped playing the disc last.
Video
DVD-RW
DVD-RW
MP3
MP3
1
During playback, press STOP C button.
The resume message will appear.
Screen:
Playing discs
Special playback
2
Press PLAY B button.
In a few seconds, playback will resume from the point at which it stopped last.You can resume play at the same point even if you turn off the unit.
To cancel the resume play and start playing the disc from the beginning, press STOP C button the second time while the play­back is stopped.
1 2
Before you start Connections
Getting started
2
Recording Playing discs
Resume ON
Fast forward / Fast reverse
DVD-V
DVD-V
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
CD
CD
MP3
MP3
1
During playback, press D or E button.
Every time you press D or E button, approximate speed will be changed as follows. (For DVD discs, the sound will be output during playback in fast forward of x2 only if you set “Fast Forward with Audio” to “ON” for the “Playback” setting in the SETUP menu.)
FWD
REW
For Audio CDs, approximate speed is fixed at x8 with sound. For MP3 files, approximate speed is fixed at x16. To r eturn to the normal playback, press PLAY B button.
FWD
REW
x20
FWD
REW
Normal
speed
playback
FWD
REW
FWD
REW
x2 x20x5 x40x40
FWD
REW
Note
•For MP3 files, playback will
resume from the beginning of the track at which playback
was stopped.
1
1
Note
•Forward/reverse speed will be
indicated with icons as fol­lows. Forward (Approx. Speed) x2: x20: x40: Reverse (Approx. Speed) x5: x20:
x40:
1
51
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
Playing discs
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Special playback (cont’d)
Skipping TV commercials during play
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
You can skip TV commercials by pressing CM SKIP button, so that you can enjoy the recorded pro­grams without interrupting.
1
During playback, press CM SKIP button.
Normal playback will start at 30 seconds ahead from the point you press CM SKIP button. Every time you press CM SKIP button, the searching point will be extended by 30 seconds ahead. You can press up to 6 times (180 seconds).
VR
DVD-RW
DVD-RW
e.g. Press CM SKIP button once
CM Skip 30 sec.
(forwarding 30 seconds.)
B
Playback will restart automatically.
1
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
Pause
DVD-V
DVD-V
DVD-RW
DVD-RW
DVD-R
DVD-R
VR
CD
CD
DVD-RW
DVD-RW
MP3
MP3
1
During playback, press PAUSE F button.
Playback will pause and sound will be muted.
Video
2
Press PLAY B button to resume play.
2
1
52
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Step by step playback
DVD-V
DVD-V
VR
DVD-RW
DVD-RW
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
1
During playback, press PAUSE F button.
Playback will pause and sound will be muted.
Playing discs
Special playback (cont’d)
2
Press SKIP G button repeatedly.
The playback will advance one frame (or step) at a time when you press the skip button with the sound muted.
To play step by step back­ward:
Press SKIP H button repeatedly. Every time you press the button, the playback will go backward by one frame.
2
Before you start Connections
Getting started
Recording Playing discs
3
3
Press PLAY B button to resume play.
Slow forward / Slow reverse play
DVD-V
DVD-V
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
VR
DVD-RW
DVD-RW
1
During playback, press PAUSE k button, then press D or E button.
Every time you press D or E button, approximate speed will be changed as follows. (The sound will remain mute.)
FWD
REW
To r eturn to the normal playback, press PLAY B button.
FWD
REW
x1/8
FWD
REW
Pause
FWD
REW
FWD
REW
x1/16 x1/8x1/16 x1/2x1/4
FWD
REW
1
1
1
1
1
Note
•Forward/reverse speed will be
indicated with icons as fol­lows. Forward (Approx. Speed) x1/16: x1/8: x1/2: Reverse (Approx. Speed) x1/16: x1/8: x1/4:
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
53
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Zoom
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
VCR
VIDEO/TV
DVD
SEARCH
MODE
CM SKIP
ZOOM
DVD-V
DVD-V
VR
DVD-RW
DVD-RW
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
1
During playback, press ZOOM button.
Zoom menu will appear.
Screen:
11
B
01:23:45
x1.2 x1.5 x2.0
There are four options (x1.0,x1.2,x1.5 and x2.0), these are displayed excluding the cur­rent zoom rate.
DVD-Video
Playing discs
Special playback (cont’d)
2
Select a desired zoom factor to zoom using { / B buttons, then press ENTER button.
The zoom area will be displayed.
3
Select a desired zoom position using K / L / { / B buttons, then
press ENTER button.
The zoom play will start.
1
2 3
Note
• When selecting a smaller factor
than the current one, the zoom area will not be displayed.
•To remove the zoom menu, press
ZOOM button again at step 1.
•To cancel the zoom function,
select x1.0 using { / B buttons,
then press ENTER button.
Spatializer setting (Virtual surround)
DVD-V
DVD-V
VR
DVD-RW
DVD-RW
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
3
Select a desired option using K / L
ENTER button.
Your setting will be activated. ON: Outputs the virtual surround
OFF: Outputs the original sound.
1101:23:45
2
Select icon using { / B buttons, then press ENTER button.
Virtual surround menu will appear.
54
DVD-Video
1101:23:45
ON OFF
buttons, then press
sound.
DVD-Video
1
2 3
Note
• This feature is not available for
some discs.
• Select “OFF” at step 3 if the
sound is distorted.
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Marker Setup
DVD-V
DVD-V
DVD-RW
DVD-RW
DVD-R
DVD-R
VR
CD
CD
This feature allows you to assign a specific point on a disc to be called back later.
Video
DVD-RW
DVD-RW
Playing discs
Special playback (cont’d)
3
Select a desired marker num­ber using { / B buttons.
When it reaches the desired point, press ENTER button.
Before you start Connections
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
1101:23:45
2
Select icon using { / B buttons, then press ENTER button.
Marker setup menu will appear.
Screen for DVD:
1101:23:45
1 2 3 4 5 6
Screen for CD:
1 01:23:45
1 2 3 4 5 6
DVD-Video
DVD-Video
Audio CD
4
To r eturn to the marker later, select the desired marker number using { / B buttons, then press ENTER button.
2 3 4
Note
•To clear a marker, select the
marker number to be cleared, then press CLEAR/C.RESET button.
• All markers will be erased
when you operate these opera­tions listed below.
– Opening the disc tray. – Turning off the power.
– Recording to a recordable
disc.
Changing the mode between Original and Playlist. (VR mode)
•You can mark up to 6 points.
Getting started
1
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
55
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Title/Chapter search
DVD-V
DVD-V
VR
DVD-RW
DVD-RW
DVD-R
DVD-R
Video
DVD-RW
DVD-RW
Using SKIP H / G buttons
Playing discs
Search
Using DISPLAY button
1
During playback, press SKIP G button to skip the cur-
rent title or chapter and move to the next.
The title or chapter will move forward one at a time.
To go back to the previous title or chapter, press SKIP H but-
ton.The title or chapter will move backward one title at a time.
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
1101:23:45
DVD-Video
2
Select icon using { / B buttons, then press ENTER button.
‘T’ for title will be highlighted.
Title: Enter a desired title number to search using K / L buttons
or number buttons, then press ENTER button.
Title search will start.
Chapter:
To move to ‘C’ for chapter, press B button.
Enter a desired chapter num­ber to search using K / L but-
tons or number buttons, then press ENTER button.
Chapter search will start.
2
1
2
1
56
Track search
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
SEARCH
MODE
CM SKIP
ZOOM
CD
MP3
MP3
CD
Using SKIP H / G buttons
Playing discs
Search (cont’d)
Using DISPLAY button
Before you start Connections
1
During playback, press SKIP G button to skip the cur-
rent track and move to the next.
The track will move forward one at a time.
To go back to the previous track, press SKIP H button. The track
will move backward one at a time.
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
1 01:23:45
Audio CD
2
Select icon using { / B buttons, then press ENTER button.
‘T’ for track will be highlighted.
3
Enter a desired track number to search using K / L buttons
or number buttons, then press ENTER button.
Track search will start.
Getting started
1
2 3
Recording Playing discs
1
Editing
DVD-V
DVD-V
DVD-RW
DVD-RW
VR
DVD-R
DVD-R
CD
CD
Time search
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen for DVD:
1101:23:45
Screen for CD:
1 01:23:45
Video
DVD-RW
DVD-RW
DVD-Video
Audio CD
2
Select icon using { / B buttons, then press ENTER button.
‘T’ for title or track will be high­lighted. To move to the clock icon, press B button.
3
Enter a desired time to search using K / L buttons or
number buttons, then press ENTER button.
Time search will start.
Note
• Time search function is avail-
able only in the same track or
title.
Changing the SETUP menu
VCR functions
1
2
Others
3
Español
Français
57
SPACE
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
ZOOM
Repeat/Random/Program play
Repeat play
DVD-V
DVD-V
VR
DVD-RW
DVD-RW
DVD-R
DVD-R
CD
CD
Video
DVD-RW
DVD-RW
MP3
MP3
1
During playback, press DIS­PLAY button.
The display menu will appear.
1101:23:45
DVD-Video
2
Select icon using {/ Bbut­tons, then press ENTER button.
Repeat menu will appear.
Screen:
1101:23:45
OFF Title Chapter A-B
DVD-Video
3
Select a desired option to repeat using K / L buttons, then press ENTER button.
The selected repeat play will start.
Playing discs
Title:
The current title will be played repeatedly. (DVD only)
Chapter:
The current chapter will be played repeatedly. (DVD only)
All:
The current disc will be played repeatedly. CD, MP3 and DVD­RW (VR mode only)
A-B:
The A-B point will be played repeatedly. When pressing ENTER button while A-B is highlighted, the start­ing point (A) will be decided.
Press ENTER button again to select the ending point (B).
Track:
The current track will be played repeatedly. (CD, MP3 only)
Group:
The current group will be played repeatedly. (MP3 only)
.@/:
GHI
REC
OPEN/
CLOSE
ABC
DEF
JKL
MNO
TUV
WXYZ
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
1
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
+
PQRS
MONITOR
2
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
DVD
REC/OTR
CH
SETUP
FWDREW
3
RETURN
VCR
SLOW
SKIP
Note
• The A-B Repeat playback can
only be set within the current title (for DVDs), or current track (for Audio CDs).
•To cancel the repeat playback,
select OFF at step 2.
•You cannot select “Group”
during the random playback
of MP3 files.
Random play
CD
MP3
MP3
CD
With this function, you can play a disc randomly instead of playing it in the original order.
First:
DVD
1
Press SETUP button to dis­play SETUP/CD menu.
SETUP/CD menu will appear.
Screen:
Setup Menu
58
2
Select “CD” using { / B but- tons, then press ENTER but­ton.
CD Playback Mode menu will appear.
CD Playback Mode
Random Play
Program Play
3
Select “Random Play” using K / L buttons, then press ENTER button.
Random playback will start.
2 3
1
Note
•To cancel random playback,
press STOP C button twice
during random playback.
Repeat/Random/Program play (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Program play
CD
CD
You can program the disc to play in your desired order.
First:
DVD
1
Press SETUP button to dis­play SETUP/CD menu.
SETUP/CD menu will appear.
Screen:
Setup Menu
2
Select “CD” using { / B but- tons, then press ENTER but­ton.
CD Playback Mode menu will appear.
CD Playback Mode
Random Play
Program Play
Playing discs
3
Select “Program Play” using K / L buttons, then press
ENTER button.
Program play list will appear.
CD Playback Mode > Program Play
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
Total 00:00:00
4
Select a desired track using K / L buttons, then press ENTER button or B button.
A cursor will move to the next.
CD Playback Mode > Program Play
- - - - - - - - - - - - - -- -- -
07
- - - - - - - - - - - - - -- -- -
- -
- - - - - - - - - - - - - -- -- -
- -
- - - - - - - - - - - - - -- -- -
- -
- - - - - - - - - - - - - -- -- -
- -
Total 00:04:30
5
Press PLAY B button to start program playback.
Program playback will start.
2 3 4
Before you start Connections
4
Getting started
Recording Playing discs
1
5
Editing
Changing the SETUP menu
VCR functions
Note
•To erase tracks you selected,
press CLEAR/C.RESET but­ton.
•You can make program set-
tings up to 50.
•To cancel program playback,
press STOP C button twice during program playback.
•You may also select a desired
track using Number buttons
at step 4.
Others
Español
Français
59
Playing discs
Selecting the format of audio and video
You can select an audio or video format as you prefer depending on the contents of the disc you are playing.
Switching audio soundtrack
DVD-V
DVD-V
When playing a DVD-Video disc recorded with two or more soundtracks (these are often in different languages), you can switch between them anytime during playback. On DVD-RW discs recorded in VR mode, you can switch to main (L), sub audio (R) or a mix of both (L/R).
VR
DVD-RW
DVD-RW
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
1101:23:45
DVD-Video
<DVD-RW VR mode>
1100:00:00
1 Dolby Digital Dual L/R 2 Dolby Digital 2ch ----
DVD-RW VR Original
3
Select a desired audio sound­track using K / L buttons,
then press ENTER button.
<DVD-Video> Audio soundtrack will switch.
<DVD-RW VR mode> Audio channel menu will appear. Follow the step 4.
L/R L R
DVD-RW VR Original
1100:00:00
1 Dolby Digital Dual 2 Dolby Digital 2ch
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
1
2 3 4
2
Select icon using { / B buttons, then press ENTER button.
Audio menu will appear.
<DVD-Video>
DVD-Video
1 Dolby Digital 5.1ch English 2 Dolby Digital 2ch Japanese
60
1100:00:00
4
Select a desired audio chan­nel using K / L buttons, then
press ENTER button.
Audio channel will switch.
Note
Some discs will only allow you to change the sound­track from the disc’s menu. Press TOP MENU button or MENU / LIST button to dis­play the disc’s menu.
On DVD-RW discs recorded in VR mode that may have both a main and a sub audio channel, you can switch to main (L), sub audio (R) or a mix of both (L/R).
This unit CANNOT record in both stereo and SAP (Secondary Audio Program) at the same time.
Selecting the format of audio and video (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
CD
MP3
MP3
CD
When playing Audio CDs or MP3 files you can switch between stereo, just the left channel or just the right channel.
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
1 00:00:00
Audio CD
Playing discs
2
Select icon using { / B buttons, then press ENTER button.
Audio menu will appear.
3
Select a desired audio chan­nel using K / L buttons, then
press ENTER button.
Audio channel will switch.
1 00:00:00
L/R L R
Audio CD
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
MONITOR
VCR
SLOW
SKIP
.@/:
GHI
PQRS
SPACE
REC
AUDIO DISPLAY
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
Before you start Connections
OPEN/
CLOSE
ABC
DEF
JKL
MNO
TUV
WXYZ
Getting started
TOP MENUMENU/LIST
1
2
SETUP
DVD
REC/OTR
CH
FWDREW
3
Recording Playing discs
Switching subtitles
DVD-V
DVD-V
Many DVD Video discs have subti­tles in one or more languages. The case usually tells you which subtitle languages are available. You can switch subtitle languages anytime during playback.
VR
DVD-RW
DVD-RW
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
1101:23:45
DVD-Video
2
Select icon using { / B buttons, then press ENTER button.
Subtitle menu will appear.
1100:00:00
OFF 1English 2Japanese
DVD-Video
3
Select a desired subtitle lan­guage using K / L buttons,
then press ENTER button.
Subtitle will be displayed in the selected language.
When selecting “OFF,” subtitle will disappear.
Note
• Some discs will only allow you to change the subtitle from the disc’s menu. Press TOP MENU button or MENU / LIST button to display the
disc’s menu.
Editing
Changing the SETUP menu
1
VCR functions
2 3
Others
Español
Français
61
Selecting the format of audio and video (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Switching camera angles
DVD-V
DVD-V
Some DVD Video discs feature scenes shot from two or more angles, check the case for details: it should be marked with an angle icon if it contains multi-angle scenes.
1
During playback, press DIS­PLAY button.
The display menu will appear.
Screen:
1101:23:45
DVD-Video
Playing discs
2
Select icon using { / B buttons, then press ENTER button.
Angle will switch each time you press ENTER button.
2
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
1
Angle icon appears when a switch­ing camera angle is available.
Reducing block noise
DVD-V
DVD-V
DVD-RW
DVD-RW
DVD-R
DVD-R
VR
DVD-RW
DVD-RW
1
During playback, press DIS-
Screen:
1101:23:45
PLAY button.
The display menu will appear.
2
Select icon using { / B buttons, then press ENTER button.
NR menu will appear.
Video
DVD-Video
OFF Type 1 Type 2
DVD-Video
1100:00:00
3
Select a desired option using K / L buttons, then press
ENTER button.
Your setting will be activated.
This function reduces noise in the playback picture.When playing back discs recorded in long time mode such as SLP or SEP mode, select "Type 1" or "Type 2". ("Type 2" is more effective.) When playing back discs with a few noises such as DVD-Video discs, select "OFF".
1
2 3
62
Editing
Information on disc editing
Before you start Connections
Guide to a title list
Title list allows you to check the titles recorded on the disc easily.You can choose a title to edit from this screen and easily edit the titles as you prefer.
Disc > Edit > Original
1 1 32
JAN/1 1:00AM
4:00AM
JAN/1
Disc > Edit > Original
JAN/1 1:00AM CH12 XP
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1
5:00AM
21
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
6
JAN/1 6:00AM
3
ON
0:01:25
Editing discs in Video mode
You can edit discs in Video mode for the following items. Be sure that once you edit titles, they will not remain as recorded originally.
• Deleting titles (Refer to page 65)
• Putting names on titles (Refer to pages 66-67)
• Setting or clearing chapter markers (Refer to page 68)
Note
Once a disc is finalized, editing the disc or recording to the disc will not be available. (Except DVD-RW discs in VR mode.)
A playlist is not available with the DVD-R discs
and DVD-RW discs in Video mode.
Getting started
Recording Playing discs
8
6 5
7
4
1. Titles recorded on the disc can be selected to
edit by pressing ENTER button with the cursor on the title.
2. Protect icon, which appears when the title has
been protected.
3. The arrow icon, which means the title list
includes a next or a previous page. Press B or { button by following direction of the icon.
4. The menus in here for editing titles as you pre-
fer. The available menus depends on the disc type and the format type.
5. The details of the title, which can be changed to
the title name you will edit.
6. Time status bar of the title.
7. The selected title thumbnails from the title list.
8. Playback status of the current disc.
Editing
Changing the SETUP menu
VCR functions
Others
Español
63
Français
Editing
Information on disc editing (cont’d)
Editing discs in VR mode
For discs in VR mode, you can edit from “Original” menu or “Playlist” menu, which is created from the original.
Editing original titles
The following items can be used to edit the original titles.
• Deleting titles (Refer to page 69)
• Deleting parts of titles (Refer to pages 70-71)
• Putting names on titles (Refer to pages 71-72)
• Setting or clearing chapter markers (Refer to pages 73-74)
• Setting pictures for thumbnails (Refer to pages 74-75)
• Setting titles to protect (Refer to page 76)
• Releasing titles from protecting (Refer to page 77)
Note
Editing playlists
You can create a playlist from original titles, so that you can edit as you prefer without losing original titles. The following items you can edit with a playlist.
• Deleting titles (Refer to page 78)
• Deleting parts of titles (Refer to pages 79-80)
• Putting names on titles (Refer to pages 80-81)
• Setting or clearing chapter markers (Refer to pages 82-83)
• Setting pictures for thumbnails (Refer to pages 83-84)
•Adding titles to a playlist (Refer to page 85)
• Deleting a playlist (Refer to page 86)
Original titles once edited will not remain as recorded originally.When you want to leave the original as it is, edit the playlist as you prefer. (Refer to pages 78-86)
64
Editing DVD-RW discs in Video mode
Deleting titles
Video
DVD-RW
DVD-RW
You can delete titles which you do not need anymore. Be sure to know that the titles once deleted cannot be brought back to the disc. When the last title in the title list in Video mode is deleted, the disc space to record will be increased.
First:
DVD
Editing
3
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Edit menu will appear.
Disc > Edit
Title Delete
1
Edit Title Name Chapter Mark
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
+
MONITOR
.@/:
GHI
PQRS
REC
CLOSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
Before you start Connections
OPEN/
DEF
MNO
WXYZ
Getting started
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Titlelist will appear.
Screen:
Disc > Edit
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
JAN/ 1 1:00AM CH12 XP
0:01:25
4
Select “Title Delete” using K / L buttons, then press ENTER button.
Option window will appear.
Disc > Edit
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Edit Title Name Chapter Mark
Yes No
0:01:25
5
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Title will be deleted.
Disc > Edit
Title Delete
1
Edit Title Name Chapter Mark
1 2 3 4 5
RETURN
VCR
SLOW
SKIP
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
DVD
REC/OTR
CH
SETUP
FWDREW
Recording Playing discs
1 6
Editing
Changing the SETUP menu
VCR functions
JAN/ 1 1:00AM CH12 XP
Yes No
Writing to Disc
This operation may take a while to be completed.
6
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
Others
Español
Français
65
Editing DVD-RW discs in Video mode (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Putting names on titles
Video
DVD-RW
DVD-RW
You can put title names on the titles and change the names from this menu. The names you put on the titles will be displayed on a titlelist.
First:
DVD
Editing
4
Select “Edit Title Name” using K / L buttons, then
press ENTER button.
A window for entering a title name will appear.
5
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
2
Select “Edit” using K / L but- tons, then press ENTER button.
Titlelist will appear.
Screen:
Disc > Edit
1 1 32
3
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Edit menu will appear.
JAN/1 1:00AM
JAN/1 4:00AM
Disc > Edit
JAN/ 1 1:00AM CH12 XP
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
Title Delete
1
Edit Title Name Chapter Mark
0:01:25
Disc > Edit > Edit Title Name
JAN/ 1 1:00AM CH12 XP
A B C
1
a b c 1 2 3
@ ! ?
0:01:25
5
To enter a title name, follow the steps of "Guide to edit title name" on this page.
character set
Disc > Edit > Edit Title Name
A B C
1
a b c 1 2 3
@ ! ?
JAN/ 1 1:00AM CH12 XP
area for entering title names
When you finish entering a title name, press ENTER button.
0:01:25
1 2 3 4 5
[
Guide to edit title name
[
Step1]: Select a desired character set using K/L
buttons, then press ENTER button.
[
]
Step2
: Press Number buttons following by the list
below.
Select
ABC
Press
<space>
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
*1 Press button, character set will be changed to the " @
*2 Press to buttons, character set will be changed to the previous input mode automatically.
To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. To go on to the next entering area for letters,
press button.
You can enter up to 30 letters.
abc
<space> <space>
(*1) (*1)
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
" mode automatically.
!?
123
]
A B C
a b c 1 2 3
@ ! ?
@ ! ?
0
! ” # $ % & ’ ( ) * + , - . / : ;
1
< = > ? @ [ ] ^ _ { | }
(*2)
2
(*2)
3
(*2)
4
(*2)
5
(*2)
6
(*2)
7
(*2)
8
(*2)
9
1
66
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Editing DVD-RW discs in Video mode (cont’d)
6
Select “Yes” using { / B but- tons, then press ENTER but­ton.
The name you entered will be activated for the title.
Disc > Edit > Edit Title Name
abc
Writing to Disc
This operation may take a while to be completed.
1
A B C
a b c 1 2 3
@ ! ?
Yes No
Editing
6
7
Before you start Connections
Getting started
Recording Playing discs
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
Editing
Changing the SETUP menu
VCR functions
Others
Español
67
Français
Editing DVD-RW discs in Video mode (cont’d)
Setting or clearing chapter markers
Video
DVD-RW
DVD-RW
You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can set chapter markers at a specified time you selected for titles with more than 5 minutes.
First:
DVD
Disc > Edit
JAN/ 1 1:00AM CH12 XP
4
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Select “Chapter Mark” using K / L buttons, then press
ENTER button.
Option window will appear.
Disc > Edit
JAN/ 1 1:00AM CH12 XP
Editing
Title Delete
1
Edit Title Name Chapter Mark
Title Delete
1
Edit Title Name Chapter Mark
0:01:25
OFF 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes
0:01:25
1 2 3 4 5 6
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
1 7
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Titlelist will appear.
Screen:
Disc > Edit
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
3
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Edit menu will appear.
68
5
Select a desired time using K / L buttons, then press ENTER button.
Option window will appear.
Disc > Edit
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Edit Title Name Chapter Mark
OFF 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes
Yes No
0:01:25
6
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Chapter markers will be added at the specified time.
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
Note
•You cannot select a time for putting markers beyond a length of a title.
• When recording at the recording speed other than XP or SEP, the length of chap­ters may be slightly longer or shorter than the one speci­fied at the step 5.
•A chapter marker may be delayed according to the
recording content.
Editing DVD-RW discs in VR mode (Original)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Deleting titles
VR
DVD-RW
DVD-RW
When a title is deleted from an original list in VR mode, the disc space to record will be increased. Be advised that the titles once deleted cannot be brought back to the disc.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Editing
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Original menu will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
ON
0:01:25
5
Select “Title Delete” using K / L buttons, then press ENTER button.
Option window will appear.
1 2 3 4 5 6
1 7
Before you start Connections
Getting started
Recording Playing discs
2
Select “Edit” using K / L but- tons, then press ENTER button.
Screen:
Disc > Edit > Original
Disc > Edit
Original
1 1 32
Original/PlayList menu will appear.
3
Select “Original” using { / B buttons, then press ENTER button.
Original list will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
ON
Yes No
0:01:25
6
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Title will be deleted.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Writing to Disc
This operation may take a while to be completed.
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
ON
Yes No
Editing
Changing the SETUP menu
VCR functions
Others
Español
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
.
Français
69
Editing DVD-RW discs in VR mode (Original) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Deleting parts of titles
VR
DVD-RW
DVD-RW
You can delete part of a title, the disc space to record will be increased. Be advised that the parts once deleted cannot be brought back to the disc.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Editing
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Original menu will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
ON
0:01:25
1 2
1
3
Disc
Edit
Format
Finalize
Disc Protect OFF ON
2
Select “Edit” using K / L but- tons, then press ENTER button.
Screen:
Disc > Edit > Original
Disc > Edit
Original
1 1 32
Original/PlayList menu will appear.
3
Select “Original” using { / B buttons, then press ENTER button.
Original list will appear.
5
Select “Scene Delete” using K / L buttons, then press
ENTER button.
Option window will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
Start End Preview Delete
0:00:55
6
Press ENTER button to decide a start point, then press ENTER button to decide an end point.
A cursor will move to “Preview.” You can check a preview.
<Preview>
Before editing
Start point End point
4 5 6
70
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
Edited
Editing
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
SEARCH
MODE
CM SKIP
ZOOM
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Editing DVD-RW discs in VR mode (Original) (cont’d)
Before you start Connections
7
Select “Delete” using K / L buttons, then press ENTER button.
Option window will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Putting names on titles
VR
DVD-RW
DVD-RW
You can put title names on the titles and change the names from this menu. The names you put on the titles will be displayed on a titlelist.
DVD
Disc
Edit
Format
Finalize
Disc Protect OFF ON
First:
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
Start End Preview Delete
Yes No
0:01:25
8
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Part of a title will be deleted.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
Start End Preview Delete
Yes No
This operation may take a while to be completed.
9
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
7 8
Note
•You cannot select “Scene Delete” when the number of chapter markers in the original
or playlist is more than 900.
1 2
Getting started
Recording Playing discs
9
Editing
Changing the SETUP menu
VCR functions
1
Others
Español
Français
71
Editing
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Editing DVD-RW discs in VR mode (Original) (cont’d)
3
Select “Original” using { / B buttons, then press ENTER button.
Original list will appear.
Disc > Edit > Original
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Original menu will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
5
Select “Edit Title Name” using K / L buttons, then
press ENTER button.
A window for entering a title name will appear.
Disc > Edit > Original > Edit Title Name
JAN/ 1 1:00AM CH12 XP
1
A B C
a b c 1 2 3
@ ! ?
0:01:25
0:01:25
6
To enter a title name, follow the steps of "Guide to edit title name" on this page.
character set
Disc > Edit > Original > Edit Title Name
A B C
1
a b c 1 2 3 @ ! ?
JAN/ 1 1:00AM CH12 XP
0:01:25
3 4
6
8
area for entering title names When you finish entering a title name, press ENTER button.
5 6 7
7
Select “Yes” using { / B but- tons, then press ENTER but­ton.
The name you entered will be activated for the title.
ON
Disc > Edit > Original > Edit Title Name
abc
Writing to Disc
1
A B C
a b c 1 2 3
@ ! ?
Yes No
This operation may take a while to be completed.
8
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
[
Guide to edit title name
[
Step1]: Select a desired character set using K/L
buttons, then press ENTER button.
[
]
Step2
: Press Number buttons following by the list
below.
Select
ABC
Press
<space>
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
*1 Press button, character set will be changed to the " @
*2 Press to buttons, character set will be changed to the previous input mode automatically.
To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. To go on to the next entering area for letters,
press button.
You can enter up to 30 letters.
abc
<space> <space>
(*1) (*1)
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
" mode automatically.
!?
123
]
A B C
a b c 1 2 3 @ ! ?
@ ! ?
0
! ” # $ % & ’ ( ) * + , - . / : ;
1
< = > ? @ [ ] ^ _ { | }
(*2)
2
(*2)
3
(*2)
4
(*2)
5
(*2)
6
(*2)
7
(*2)
8
(*2)
9
72
Editing DVD-RW discs in VR mode (Original) (cont’d)
Setting or clearing chapter markers
VR
DVD-RW
DVD-RW
You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can put a chapter marker anywhere you want. When the number of chapter markers in the original list comes to 999 in total, you cannot add any more chapter markers.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Disc > Edit > Original
JAN/1 1:00AM
JAN/1 4:00AM
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Original menu will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
5
Select “Chapter Mark” using K / L buttons, then press
ENTER button.
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Option window will appear.
Disc > Edit > Original
Chapter 1/1
JAN/ 1 1:00AM CH12 XP
Editing
1 1 32
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
0:01:25
Add Delete
0:01:25
Before you start Connections
.@/:
GHI
REC
CLOSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
OPEN/
DEF
MNO
WXYZ
Getting started
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
+
PQRS
MONITOR
1
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
DVD
REC/OTR
CH
SETUP
FWDREW
Recording Playing discs
1
Editing
Changing the SETUP menu
VCR functions
2 3 4
RETURN
VCR
SLOW
SKIP
5
ON
ON
6
Original
3
Select “Original” using { / B buttons, then press ENTER button.
Original list will appear.
6
Select “Add” or “Delete” using K / L buttons, then
press ENTER button.
Option window will appear.
<Add>:
Disc > Edit > Original
Chapter 1/1
F
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
Add Delete
Yes No
0:01:25
Others
Español
ON
Français
73
Editing DVD-RW discs in VR mode (Original) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
SEARCH
MODE
CM SKIP
ZOOM
<Delete>:
Disc > Edit > Original
Chapter 2/2
F
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
Add Delete
Yes No
ON
0:01:25
• You cannot delete the first chapter marker of each title.
7
Select “Yes” using { / B but- tons, then press ENTER button.
<Add>: A chapter marker will be added.
Disc > Edit > Original
Chapter 1/1
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
Add Delete
Yes No
ON
Editing
<Delete>: The chapter marker which you selected will be deleted.
Disc > Edit > Original
Chapter 2/2
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Protect OFF
Add Delete
Yes No
ON
This operation may take a while to be completed.
8
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
7
8
This operation may take a while to be completed.
Setting pictures for thumbnails
You can set a picture to each title for a thumbnail. It helps you to remem­ber the contents of the title you are playing.The beginning picture has been selected as the default.
First:
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
74
DVD-RW
DVD-RW
VR
DVD
Disc
Edit
Format
Finalize
Disc Protect OFF ON
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
1 2
1
Note
• If a selected picture for a thumbnail is deleted by delet­ing a part of a title, a default
picture will be selected.
Editing
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Editing DVD-RW discs in VR mode (Original) (cont’d)
Before you start Connections
3
Select “Original” using { / B buttons, then press ENTER button.
Original list will appear.
Disc > Edit > Original
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Original menu will appear.
Disc > Edit > Original
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
ON
6
Select “Yes” using { / B but- tons, then press ENTER but­ton.
A picture for thumbnail will be set.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
Yes No
ON
This operation may take a while to be completed.
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
3 4 5 6
5
7
Getting started
Recording Playing discs
Editing
JAN/ 1 1:00AM CH12 XP
5
Select “Index Picture Set” using K / L buttons. Use SKIP H / G, REW E, FWD D, PLAY B and PAUSE F but-
tons to decide the picture you want to select as a thumbnail.Then press ENTER button.
Option window will appear.
Disc > Edit > Original
F
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
Yes No
0:01:25
0:01:25
Changing the SETUP menu
VCR functions
Others
ON
Español
Français
75
Editing DVD-RW discs in VR mode (Original) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Setting titles to protect
VR
DVD-RW
DVD-RW
To prevent accidental editing or erasing the titles, you can protect them from the original menu.
First:
DVD
Editing
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Original menu will appear.
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
3
Select “Original” using { / B buttons, then press ENTER button.
Original list will appear.
Disc > Edit > Original
JAN/1 1:00AM
1 1 32
JAN/1 2:00AM JAN/1 3:00AM
54
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
ON
0:01:25
5
Select “Protect OFF ➔ ON” using K / L buttons, then press ENTER button.
Option window will appear.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
Yes No
ON
0:01:25
6
Select “Yes” using { / B but- tons, then press ENTER button.
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect OFF
Yes No
ON
This operation may take a while to be completed.
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
1 2
1
3
7
4 5 6
76
JAN/1 4:00AM
JAN/1 5:00AM
To protect a whole disc (DVD-RW VR mode Only):
Select “Disc Protect” from Disc menu, then select “Yes”.
Editing DVD-RW discs in VR mode (Original) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Releasing titles from protecting
VR
DVD-RW
DVD-RW
You are allowed to release the titles protecting feature once pro­tected.
First:
DVD
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Original menu will appear.
Editing
Before you start Connections
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
3
Select “Original” using { / B buttons, then press ENTER button.
Original list will appear.
Disc > Edit > Original
JAN/1 1:00AM
JAN/1 4:00AM
1 1 32
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
Disc Edit > Original
JAN/ 1 2:00AM CH12 XP
Title Delete
2
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect ON
OFF
0:01:25
“Protect ON OFF” is selected.
5
Press ENTER button.
Option window will appear.
Disc Edit > Original
B
JAN/ 1 2:00AM CH12 XP
Title Delete
2
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect ON
Yes No
OFF
0:01:25
6
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Disc Edit > Original
JAN/ 1 2:00AM CH12 XP
Writing to Disc
Title Delete
2
Scene Delete Edit Title Name Chapter Mark Index Picture Set Protect ON
Yes No
OFF
This operation may take a while to be completed.
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
1 2 3 4 5 6
Getting started
Recording Playing discs
1 7
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
77
Editing DVD-RW discs in VR mode (Playlist)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Deleting titles
VR
DVD-RW
DVD-RW
In VR mode, even when a title is deleted from a Playlist, the original title will remain in an Original list. The disc space to record will not be increased.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Editing
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
0:01:25
5
Select “Title Delete” using K / L buttons, then press ENTER button.
Option window will appear.
1 2
1
3
7
4 5 6
2
Select “Edit” using K / L but- tons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
3
Select “PlayList” using { / B buttons, then press ENTER button.
Playlist will appear.
Disc > Edit > Playlist
JAN/1 1:00AM
JAN/1 4:00AM
Disc > Edit
Original
1 1 32
JAN/1 2:00AM JAN/1 3:00AM
Add New
54
Delete
JAN/1 5:00AM
Title
Playlist
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
0:01:25
6
Select “Yes” using { / B but- tons, then press ENTER button.
Title will be deleted.
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
This operation may take a while to be completed.
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
78
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Deleting parts of titles
VR
DVD-RW
DVD-RW
You can delete a specific part of a title. Even when a title is deleted from the playlist, the original title will remain. The disc space to record will not be increased.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Editing
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
0:01:25
5
Select “Scene Delete” using K / L buttons, then press
ENTER button.
Option window will appear.
1 2 3 4 5 6
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
MONITOR
VCR
SLOW
SKIP
.@/:
GHI
PQRS
SPACE
REC
AUDIO DISPLAY
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
Before you start Connections
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
Getting started
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
1
Recording Playing discs
2
Select “Edit” using K / L but- tons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
3
Select “PlayList” using { / B buttons, then press ENTER button.
Playlist will appear.
Disc > Edit > Playlist
1 1 32
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture
Start End Preview Delete
0:00:55
6
Press ENTER button to decide a start point, then press ENTER button to decide an end point.
A cursor will move to “Preview”. You can check a preview.
<Preview>
Before editing
Start point End point
Editing
Changing the SETUP menu
VCR functions
Others
Español
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
Add New
54
Title
Delete
JAN/1 5:00AM
Playlist
Edited
Instructions continue to the next page.
Français
79
Editing
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
VCR
VIDEO/TV
DVD
SEARCH
MODE
CM SKIP
ZOOM
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Part of a title will be deleted.
7
Select “Delete” using K / L buttons, then press ENTER button.
Option window will appear.
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture
Start End Preview Delete
Yes No
8
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Putting names on titles
VR
DVD-RW
DVD-RW
You can put names on the titles and change the names from this menu.
DVD
Disc
Edit
Format
Finalize
Disc Protect OFF ON
The names you put on the titles will be displayed on a titlelist.
First:
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
2
Select “Edit” using K / L but- tons, then press ENTER button.
80
0:01:25
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture
Start End Preview Delete
Yes No
This operation may take a while to be completed.
9
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
3
Select “PlayList” using { / B buttons, then press ENTER button.
Playlist will appear.
Disc > Edit > Playlist
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
Add New
54
Title
Delete
JAN/1 5:00AM
Playlist
7 8
9
Note
•You cannot select “Scene Delete” when the number of chapter markers in the original
or playlist is more than 900.
1 2
1
3
Editing
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Before you start Connections
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
0:01:25
5
Select “Edit Title Name” using K / L buttons, then
press ENTER button.
A window for entering a title name will appear.
Disc > Edit > Playlist > Edit Title Name
JAN/ 1 1:00AM CH12 XP
A B C
1
a b c 1 2 3
@ ! ?
0:01:25
6
To enter a title name, follow the steps of "Guide to edit title name" on this page.
character set
Disc > Edit > Playlist > Edit Title Name
A B C
1
a b c 1 2 3 @ ! ?
JAN/ 1 1:00AM CH12 XP
area for entering title names
When you finish entering a title name, press ENTER button.
0:01:25
7
Select “Yes” using { / B but- tons, then press ENTER but­ton.
The name you entered will be activated for the title.
Disc > Edit > Playlist > Edit Title Name
abc
Writing to Disc
1
A B C
a b c 1 2 3
@ ! ?
Yes No
This operation may take a while to be completed.
8
After writing to disc is com­pleted, press SETUP to exit DISC menu.
.@/:
GHI
PQRS
REC
OPEN/
CLOSE
ABC
JKL
MNO
TUV
WXYZ
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
DEF
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
+
MONITOR
4 5 6 7
[
Step1]: Select a desired character set using K/L
buttons, then press ENTER button.
[
Step2
below.
Select
Press
*1 Press button, character set will be changed to the " @
*2 Press to buttons, character set will be changed to the previous input mode automatically.
To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. To go on to the next entering area for letters,
press button.
You can enter up to 30 letters.
RETURN
VCR
SLOW
SKIP
[
Guide to edit title name
]
: Press Number buttons following by the list
ABC
<space>
(*1) (*1)
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
" mode automatically.
!?
SETUP
VIDEO/TV
DVD
REC
REC/OTR
SPEED
CH
STOP PLAY
FWDREW
PAUSE
]
A B C
a b c 1 2 3
@ ! ?
abc
<space> <space>
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
123
@ ! ?
0
! ” # $ % & ’ ( ) * + , - . / : ;
1
< = > ? @ [ ] ^ _ { | }
(*2)
2
(*2)
3
(*2)
4
(*2)
5
(*2)
6
(*2)
7
(*2)
8
(*2)
9
Getting started
8
Recording Playing discs
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
81
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Setting or clearing chapter markers
VR
DVD-RW
DVD-RW
You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can put a chapter marker anywhere you want. When the number of chapter markers in the playlist comes to 999 in total, you cannot add any more chapter markers.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
5
Select “Chapter Mark” using K / L buttons, then press
ENTER button.
Screen:
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Option window will appear.
Editing
Disc > Edit > Playlist
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
1
1
Chapter 1/1
Add New
Title
Delete
Playlist
Title Delete Scene Delete Edit Title Name Chapter Mark Index Picture Set
0:01:25
Title Delete Scene Delete Edit Title Name
Add
Chapter Mark
Delete
Index Picture Set
0:01:25
1 2
1
3 4 5 6
Disc Setting
3
Select “PlayList” using { / B buttons, then press ENTER button.
Playlist will appear.
82
6
Select “Add” or “Delete” using K / L buttons, then
press ENTER button.
Option window will appear.
<Add>:
Disc > Edit > Playlist
Chapter 1/1
F
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
Add Delete
0:01:25
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
SEARCH
MODE
CM SKIP
ZOOM
<Delete>:
Disc > Edit > Playlist
Chapter 2/2
F
JAN/ 1 1:00AM CH12 XP
• You cannot delete the first chapter of each title.
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
Add Delete
0:01:25
Editing
The chapter marker which you selected will be deleted.
<Delete>:
Disc > Edit > Playlist
Chapter 2/2
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
Add Delete
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
+
MONITOR
.@/:
GHI
PQRS
REC
CLOSE
ABC
JKL
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
Before you start Connections
OPEN/
DEF
MNO
WXYZ
Getting started
7
S
elect “Yes” using { / B but-
tons, then press ENTER button.
A chapter marker will be added.
<Add>:
Disc > Edit > Playlist
Chapter 1/1
JAN/ 1 1:00AM CH12 XP
Writing to Disc
This operation may take a while to be completed.
Setting pictures for thumbnails
VR
DVD-RW
DVD-RW
You can set a picture to each title for a thumbnail. It helps you to remember the contents of the title you are playing.The begin­ning picture has been selected as the default.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
DVD
First:
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
Add Delete
This operation may take a while to be completed.
8
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
7
VIDEO/TV
REC
SPEED
STOP PLAY
PAUSE
SETUP
DVD
REC/OTR
CH
FWDREW
RETURN
VCR
SLOW
SKIP
1 2
Note
• If a selected picture for a thumbnail is deleted by delet­ing a part of a title, a default
picture will be selected.
Recording Playing discs
8
Editing
Changing the SETUP menu
VCR functions
Others
1
Español
Français
83
Editing
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
3
Select “PlayList” using { / B buttons, then press ENTER button.
Playlist will appear.
Disc > Edit > Playlist
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
Add New
54
Title
Delete
JAN/1 5:00AM
Playlist
4
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
Disc > Edit > Playlist
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
6
Select “Yes” using { / B but- tons, then press ENTER but­ton.
A picture for thumbnail will be set.
Disc > Edit > Playlist
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
This operation may take a while to be completed.
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
3 4 5 6
5
POWER
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
OPEN/
CLOSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
7
JAN/ 1 1:00AM CH12 XP
0:01:25
5
Select “Index Picture Set” using K / L buttons. Use SKIP H / G, REW E, FWD D, PLAY B and PAUSE F but-
tons to decide the picture you want to select as a thumbnail.Then press ENTER button.
Option window will appear.
Disc > Edit > Playlist
F
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete Edit Title Name Chapter Mark Index Picture Set
Yes No
0:01:25
84
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Adding titles to a Playlist
VR
DVD-RW
DVD-RW
You can add or delete a title in the playlist as you prefer. You can add titles to a Playlist up to 99.
First:
DVD
Editing
4
Select “Add New Title” using K / L / { / B buttons, then
press ENTER button.
Original list will appear.
Before you start Connections
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Disc > Edit
Original
Disc > Edit > Playlist > Add New Title
1 1 32
JAN/12 5:00PM JAN/12 8:00PMJAN/10 10:30AM
5
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Disc > Edit > Playlist > Add New Title
Writing to Disc
Disc > Edit > Playlist
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM
JAN/1 5:00AM
58%
JAN/1 3:00AM
54
6
JAN/12 8:00PM
1 2 3 4 5
Getting started
Recording Playing discs
1 6
Editing
Changing the SETUP menu
VCR functions
3
Select “PlayList” using { / B buttons, then press ENTER button.
Playlist will appear.
Disc > Edit > Playlist
JAN/1 1:00AM
JAN/1 4:00AM
1 1 32
JAN/1 2:00AM JAN/1 3:00AM
Add New
54
Delete
JAN/1 5:00AM
Title
Playlist
6
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
To delete a title from Playlist, refer to “Deleting titles” on page
78. To delete a Playlist, refer to “Deleting a Playlist” on page 86.
Others
Español
Français
85
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Deleting a Playlist
VR
DVD-RW
DVD-RW
A Playlist can be deleted if no longer needed.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Original/PlayList menu will appear.
Screen:
Editing
4
Select “Delete Playlist” using K / L / { / B buttons, then
press ENTER button.
Option window will appear.
Disc > Edit > Playlist
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
JAN/1 2:00AM JAN/1 3:00AM
Add New
54
Title
Delete
Playlist
JAN/1 5:00AM
Yes No
5
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Playlist will be erased. After writing to disc is completed, the unit will be in stop mode.
1 2
1
3 4 5
Disc > Edit
Original
3
Select “PlayList” using { / B buttons, then press ENTER button.
Playlist will appear.
86
Disc > Edit > Playlist
JAN/1 1:00AM
JAN/1 4:00AM
1 1 32
JAN/1 2:00AM JAN/1 3:00AM
Add New
54
Delete
JAN/1 5:00AM
Title
Playlist
Note
• Deleting a Playlist will not increase the available record-
ing time on disc.
Deleting titles
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
DVD-R
DVD-R
You can delete titles which you do not need, however the disc space to record on the disc will not be changed. Be sure to know that the titles once deleted cannot be brought back to the disc.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Editing
Editing DVD-R discs
Disc > Edit
JAN/ 1 1:00AM CH12 XP
You cannot select “Chapter Mark”.
Title Delete
1
Edit Title Name Chapter Mark
0:01:25
4
Select “Title Delete” using K / L buttons, then press ENTER button.
Option window will appear.
Disc > Edit
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Edit Title Name Chapter Mark
Yes No
0:01:25
1 2 3 4 5
1 6
Before you start Connections
Getting started
Recording Playing discs
2
Select “Edit” using K / L but- tons, then press ENTER but­ton.
Titlelist will appear.
3
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Edit menu will appear.
Screen:
Disc > Edit
JAN/1 1:00AM
JAN/1 4:00AM
1 1 32
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
5
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Title will be deleted.
Disc > Edit
JAN/ 1 1:00AM CH12 XP
Writing to Disc
Title Delete
1
Edit Title Name Chapter Mark
Yes No
This operation may take a while to be completed.
6
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
87
Putting names on titles
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
DVD-R
DVD-R
You can put names on the titles and change the names from this menu. The names you put on the titles will be displayed on a titlelist.
First:
DVD
1
Press SETUP button. Select “DISC” using { / B buttons,
then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
Editing
Editing DVD-R discs (cont’d)
4
Select “Edit Title Name” using K / L buttons, then press ENTER button.
A window for entering a title name will appear.
Disc > Edit > Edit Title Name
JAN/ 1 1:00AM CH12 XP
A B C
1
a b c 1 2 3
@ ! ?
0:01:25
5
To enter a title name, follow the steps of "Guide to edit title name" on this page.
character set
5
1 2
1
3
7
4 5 6
2
Select “Edit” using tons, then press ENTER button.
Titlelist will appear.
Screen:
Disc > Edit
1 1 32
JAN/1 1:00AM
JAN/1 4:00AM
3
Select a desired title using K / L / { / B buttons, then press
ENTER button.
Edit menu will appear.
Disc > Edit
JAN/ 1 1:00AM CH12 XP
You cannot select “Chapter Mark”.
88
K / L
JAN/1 2:00AM JAN/1 3:00AM
54
JAN/1 5:00AM
Title Delete
1
Edit Title Name Chapter Mark
0:01:25
but-
Disc > Edit > Edit Title Name
A B C
1
a b c 1 2 3
@ ! ?
JAN/ 1 1:00AM CH12 XP
0:01:25
area for entering title names When you finish entering a title name, press ENTER button.
6
Select “Yes” using { / B but- tons, then press ENTER but­ton.
Disc > Edit > Edit Title Name
abc
Writing to Disc
1
A B C
a b c 1 2 3
@ ! ?
Yes No
This operation may take a while to be completed.
7
After writing to disc is com­pleted, press SETUP button to exit DISC menu.
[
Guide to edit title name
[
Step1]: Select a desired character set using K/L
buttons, then press ENTER button.
[
]
Step2
: Press Number buttons following by the list
below.
Select
ABC
Press
<space>
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
*1 Press button, character set will be changed to the " @
*2 Press to buttons, character set will be changed to the previous input mode automatically.
To delete letters, press CLEAR button repeatedly. Holding CLEAR button to delete all letters. To go on to the next entering area for letters,
press button.
You can enter up to 30 letters.
abc
<space> <space>
(*1) (*1)
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
" mode automatically.
!?
123
]
A B C
a b c 1 2 3
@ ! ?
@ ! ?
0
! ” # $ % & ’ ( ) * + , - . / : ;
1
< = > ? @ [ ] ^ _ { | }
(*2)
2
(*2)
3
(*2)
4
(*2)
5
(*2)
6
(*2)
7
(*2)
8
(*2)
9
Changing the SETUP menu
Tour of the SETUP menu
The following table is the contents which you can set and the default settings. Refer to the following table for useful operation.
SETUP menu ContentsItems (highlight is the default)
Before you start Connections
1.Language setting Pages 90-91
2.Display setting Pages 92-93
Disc Menu Language Set the language for disc menu.
English French Spanish
Audio Language
Original
Set the language for audio.
English French
Subtitle Language
OFF
Set the language for subtitle.
English French
OSD Background Transparency
100%
35%
Set the background transparency of OSD screen.
25%
OSD Background Color
OSD Language
Screen Saver
1 2 3
English
Français Español
OFF 5 minutes 10minutes
Set the OSD screen color. 1 (Green), 2 (Blue), 3 (Red)
Set the language for OSD (On Screen Display).
Set the time to work the screen saver on the screen.
Getting started
Recording Playing discs
Editing
3.Audio setting Pages 94-95
4.Parental setting Pages 96-97
Digital Out
Dynamic Range Control
Fast Forward with Audio
Parental Lock
(Change password)
PCM Auto
48kHz 96kHz
Dolby Digital PCM
Stream
DTS ON
OFF
ON OFF
ON OFF
ALL level 8 to 1
Enter the current four-digit password
Set whether the sound recorded in 96kHz will be down sampled in 48kHz.
Set the type of sound signal which outputs from the digital audio output jack.
Set whether DTS signal will be output or not.
Compressing the range of sound volume.
Outputting the sound during play in fast forward.
Set the parental level of your DVD discs.
Set and change the password.
Note
• If you change the setting in SETUP menu, the information of contents stays on even when the power is switched off.
Changing the SETUP menu
VCR functions
Others
Español
Français
89
Changing the SETUP menu
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Settings for Language
Press STOP button if you are playing a disc.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
4
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Playback” using K / L / ENTER button.
Option window will appear.
{ / B
buttons, then press
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
2 3
1
4
5
4
Select a desired item using K / L buttons, then press ENTER button.
90
Note
• Only the languages supported by the disc can be selected.
• Audio Language setting may not be available to some discs.
•You can change or switch off the subtitles on a DVD disc also from the disc menu if it
is available.
Changing the SETUP menu
a
All
Settings for Language (cont’d)
Disc Menu Language (Default : English)
Set the language for Disc Menu.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
Audio Language (Default : Original)
Set the Audio language.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
English
French
Original
Spanish
OFF
Other
ON
OFF
DVD
4:3 Letter Box
All
Original
English
English
Original
French
OFF
Spanish Other
ON
OFF
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Before you start Connections
Getting started
Recording Playing discs
Subtitle Language (Default : OFF)
Set the subtitle language.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
If “Other” is selected, press 4-digit code using number buttons.
English
English
French
Original
Spanish
OFF
Other
Code Input
- - - -
ON
ge
ontrol
5
Press SETUP button to exit SETUP menu.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
When you finish entering the code, press ENTER button. Refer to the lan­guage code table on page
105.
DVD
4:3 Letter Box
All
OFF
English
English
Original
French
OFF
Spanish Other
ON
OFF
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
91
Changing the SETUP menu
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Settings for Display
Press STOP button if you are playing a disc.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Display” using K / L / ENTER button.
Option window will appear.
{ / B
buttons, then press
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
DVD
35%
1
English
10 minutes
2 3
1
4
5
4
Select a desired item using K / L buttons, then press ENTER button.
92
Changing the SETUP menu
Settings for Display (cont’d)
OSD Background Transparency (Default : 35%)
Set the background transparency of OSD screen. You can choose one among 0% through 100%.
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
OSD Background Color (Default : 1 Green)
Set the OSD screen color. You can choose one among 1(Green), 2(Blue), and 3(Red).
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
OSD Language (Default : English)
Set the language for OSD.
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
DVD
35%
1
English
10 minutes
DVD
35%
1
English
10 minutes
VCR DV D
35%
1
English
10 minutes
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
DVD
100%
35%
85%
1
70%
English
50%
10 minutes
35% 25% 10% 0%
DVD
35%
1
1 2
English
3
10 minutes
VCR DV D
35%
1
English
English Français
10 minutes
Español
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Before you start Connections
Getting started
Recording Playing discs
Editing
Screen Saver (Default : 10 minutes)
Set the time to work the screen saver function on the screen.
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
DVD
35%
1
English
10 minutes
Setup > Display
OSD Background Transparency
OSD Background Color
OSD Language
Screen Saver
5
Press SETUP button to exit SETUP menu.
DVD
35%
1
OFF
English
5 minutes 10 minutes
10 minutes 15 minutes 30 minutes
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Changing the SETUP menu
VCR functions
Others
Español
Français
93
Changing the SETUP menu
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Settings for Audio
Choose the appropriate Audio settings for your equipment.
It will only affect DVD discs during playback.
Press STOP button if you are playing a disc.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
2
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Playback” using K / L / ENTER button.
Option window will appear.
{ / B
buttons, then press
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
4
Select a desired item using K / L buttons, then press ENTER button.
Digital Out
Set the digital audio output.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
4:3 Letter Box
All
English
Original
OFF
PCM
ON
Dolby Digital DTS
OFF
3 4
Note
• Dynamic Range Control func­tion is available only on the discs which are recorded in
the Dolby Digital format.
Select a setting using K / L
DVD
buttons, then press ENTER button.
Option window will appear. Proceed to steps A, B or C.
1 5
94
Changing the SETUP menu
g
Settings for Audio (cont’d)
Settings for PCM (Default :Auto)
A
Original
OFF
trol
dio
B
PCM Dolby Digital DTS
Auto 48kHz
ON
96kHz
OFF
Settings for Dolby Digital (Default : Stream)
Original
OFF
PCM
trol
udio
ON
Dolby Digital
PCM Stream
DTS
OFF
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated. Auto : Select “Auto” usually. 48kHz : If your amplifier/decoder is NOT com-
patible with 96kHz PCM, select “48kHz”. 96kHz sound will be output in 48kHz.
96kHz : If your amplifier/decoder is compatible
with 96kHz PCM, select “96kHz”. 96kHz sound will be output.
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated. PCM : Convert the Dolby Digital into PCM
(2 channel).
When your amplifier/decoder is NOT com-
patible with Dolby Digital, set to “PCM”.
Stream : Outputs Dolby Digital signals.
When your amplifier/decoder is compati­ble with Dolby Digital, set to “Stream”.
Note
When playing disc with copy­right protection
• If you select “Auto”, the sound will be down sampled at 48kHz.
• If you select “96kHz”, no digital sound will be output. Select “Auto”, so that outputting
48kHz digital sound.
Note
When playing a DVD-RW disc recorded in VR mode
• If the audio source on a disc is Dolby Digital format, set “Dolby Digital” to “PCM” so that you can switch to main (L), sub audio (R), or a mix of both (L/R) with your amplifier/decoder.
Before you start Connections
Getting started
Recording Playing discs
Settings for DTS (Default : OFF)
C
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated. ON : Outputs DTS signals.
When your amplifier/decoder is compatible with DTS, set to “ON”.
OFF : No DTS signal is output.
When your amplifier/decoder is NOT compatible with DTS, set to “OFF”.
trol
dio
Original
OFF
PCM
ON
Dolby Digital
OFF
ON
DTS
OFF
Dynamic Range Control (Default : ON)
Set to ON to compress the range between soft and loud sounds.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Fast Forward with Audio (Default : OFF)
Set to ON to output the sound during playback in fast forward of x2.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
4:3 Letter Box
All
English
Original
OFF
ON
OFF
ON OFF
ON OFF
DVD
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
DVD
Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
5
Press SETUP button to exit SETUP menu.
95
Changing the SETUP menu
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
Settings for Parental lock level
Some DVD-Video discs feature a Parental Lock level. Playback will stop if the ratings exceed the levels you set, it will require you to enter a password before the disc will playback.This fea­ture prevents your children from viewing inappropriate materi­al.
Press STOP button if you are playing a disc.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Setup Menu
2
Select “SETUP” using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
Playback Setting
{ / B
buttons, then press
3
Select “Playback” using K / L / ENTER button.
Option window will appear.
4
2 3
1
4
5
Setup > Playback
TV Aspect
4
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
Select “Parental Lock” using K / L buttons, then press ENTER button.
96
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Note
• Parental lock function may not be available to some discs.
• With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function oper­ates in the way that you have set.
• Record the password in case
you forget it.
Changing the SETUP menu
Settings for Parental lock level (cont’d)
Parental Lock (Default : All)
Set the Parental Lock level.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All
English
Original
OFF
ON
OFF
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
DVD
4:3 Letter Box
All 8
All 7
English 6 Original
5 OFF
4 3 2
ON 1
OFF
Change the parental level using K / L buttons, then press ENTER button.
Option window will appear. Proceed to steps A or B.
Before you start Connections
Getting started
A
If you
A password has not been set yet
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
select “No”, proceed
DVD
4:3 Letter Box
Change Password?
All
Yes No
8
All
7
English
6
Original
5
OFF
4 3 2
ON
1
OFF
to Step 5.
B
Enter the current password
A password has been set already
4:3 Letter Box
All
Password
8
All
* * * *
7
English
6
Original
5
OFF
4 3 2
ON
1
OFF
DVD
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
using Number buttons.
Ye s
If you to Step 5.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
Change Password?
select “No”, proceed
4:3 Letter Box
All
Yes No
8
All 7
English 6 Original
5 OFF
4 3 2
ON 1
OFF
DVD
4:3 Letter Box
Password
All
- - - -
8
All
7
English
6
Original
5
OFF
4 3 2
ON
1
OFF
DVD
Select “Yes” using s / B buttons, then enter a new password using Number buttons.
Your setting will be activated.
Change the password
Setup > Playback
Ye s
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
Select “Yes” using s / B buttons, then enter a new password using Number buttons.
Your setting will be activated.
4:3 Letter Box
Password
All
- - - -
8
All
7
English
6
Original
5
OFF
4 3 2
ON
1
OFF
Recording Playing discs
Editing
DVD
Changing the SETUP menu
VCR functions
5
Press SETUP button to exit SETUP menu.
Note
•Press CLEAR/C.RESET button to erase numbers entered incorrectly.
• When you forget the pass­word or you want to clear all settings in Parental lock, enter 4,7,3,7 using Number buttons in option window. Password will be cleared and parental
levels will be set to All.
97
Others
Español
Français
VCR
Record tab
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
POWER
OPEN/
CLOSE
ABC DEF
.@/:
VCR Plus
+
VCR
1
Press POWER button on the remote control or the front panel of the unit.
When you are playing a tape, turn the TV on and be sure to select the input to which the unit is con­nected.
Press:
VCR
VCR functions
Playback
3
During playback, press PAUSE F button.
Playback will pause and sound will be muted.
4
Press PLAY B button to resume play.
1
5
3
2 4
2
Insert a prerecorded tape, then press PLAY B button to
begin playback.
Recording
VCR
VCR
Before recording, make sure:
The desired channel is selected by pressing the number buttons on the remote control or
K/L
CHANNEL front panel of the unit.
There is a tape with a record tab in the unit.
The desired recording speed is selected in SP (standard play) or SLP (super long play) mode by pressing REC SPEED button on the remote control.
Recording speed:
Ta pe speed
Type of tape T160T120
Stereo or SAP is selected.
Refer to page 36 for instructions on timer recording.
98
buttons on the
Recording/Playback Time
T60
5
Press STOP C button to stop playback.
6
Press STOP/EJECT CAbut- ton on the front panel of the unit to eject the tape.
• When a tape without record tab is inserted, the unit will start playback automatically.
•Tracking will be automatically adjusted upon playback.To adjust the tracking manually, press the CHANNEL K/L buttons on the front panel of the unit or CHK/CHL but-
tons on the remote control.
Recording and One-touch timer recording
Note
First:
1
Press REC/OTR button to begin the recording.
To temporarily stop recording or to resume it, press PAUSE F but-
ton. After the unit has been in Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage.
2
Press STOP button when the
2-2/3hours2hours1hourSP mode
8hours6hours3hoursSLP mode
recording is completed.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, remove its record tab.To record on it later, cover the hole with cello­phane tape.
VCR
2
1
Note
•To view one channel while recording another
1)
While you are recording on the unit, press VIDEO/TV but­ton.
2) At the cable box or satel­lite box, select the channel you want to view. If you have connected the unit to a cable box or satellite box, refer to “Connection to a Cable Box or Satellite Box” section on page
14.
If OTR is finished in VCR during playback or REC mode in DVD, the VCR will be in STOP mode and the
DVD keeps the current mode.
1
Recording and One-touch timer recording (cont’d)
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
POWER
OPEN/
CLOSE
ABC
JKL
TUV
DEF
MNO
WXYZ
SPACE
.@/:
GHI
PQRS
VCR Plus
+
AUDIO DISPLAY
REC
MONITOR
CLEAR/
C.RESET
TOP MENUMENU/LIST
SETUP
RETURN
SKIP
STOP PLAY
FWDREW
PAUSE
SLOW
REC
SPEED
REC/OTR
VCR
VIDEO/TV
DVD
CH
SEARCH
MODE
CM SKIP
ZOOM
One-touch timer recording
VCR
VCR
This feature allows you to set the recording length simply by pressing REC/OTR button on the remote control or the front panel of the unit.
First:
VCR
1
During normal recording, press REC/OTR button to begin one-touch timer recording.
You can select a fixed recording time by pressing the REC/OTR button repeatedly.
VCR functions
(Normal recording)
When one-touch timer recording is finished, the unit will turn off automatically.
To cancel the one-touch timer recording within the specified time, press STOP C button.
(0:30) (1:00)
(7:30)(8:00)
Search
1
1
Note
• The remaining recording time will appear on the display panel during an OTR. Press DISPLAY button to see it on the TV screen.
•You cannot pause an OTR.
Before you start Connections
Getting started
Recording Playing discs
Index search
VCR
VCR
An index mark will be assigned at the beginning of each recording you make.You may skip to a specif­ic marked point by following the steps below.
First:
VCR
1
Press SEARCH MODE button
INDEX SEARCH
03
so that the index search menu appears.
2
Enter the number of record­ings you wish to skip using Number buttons with in 30 seconds.
3
Press g/h buttons to start index search.
If you want to go in the forward direction, press g button.
If you want to go in the reverse direction, press h button.
After index search, the VCR will play the tape automatically.
CURRENT PROGRAM Beginning of tape
Pro. 1 Pro. 2 Pro. 3
02 01 01
Pro. 4 Pro. 5
02 03
INDEX MARK
End of tape
1
3
2
3
Note
•Every time a tape is recorded, an index mark is written on
the tape.
Editing
Changing the SETUP menu
VCR functions
Others
Español
Français
99
VCR functions
Search (cont’d)
Time search
VCR
VCR
This feature allows you to go to a specific point on a tape by enter­ing the exact amount of time you wish to skip in order to reach the point.
First:
VCR
1
Press SEARCH MODE button repeatedly so that the Time search menu appears.
2
Enter your desired time to skip using Number buttons with in 30 seconds.
TIME SEARCH
2:50
3
Press g/h buttons to start time search.
If you want to go in the forward
g
h
button.
button.
direction, press If you want to go in the reverse
direction, press After time search, the unit will play the tape automatically.
1
3
VCR Plus
SEARCH
MODE
CM SKIP
ZOOM
CLEAR/
C.RESET
RETURN
+
PQRS
MONITOR
VCR
SLOW
SKIP
STOP PLAY
.@/:
GHI
REC
VIDEO/TV
REC
SPEED
PAUSE
DEF
ABC
MNO
JKL
WXYZ
TUV
SPACE
AUDIO DISPLAY
TOP MENUMENU/LIST
SETUP
DVD
REC/OTR
CH
FWDREW
2
3
Note
• These functions are not avail-
able during recording.
•Press STOP button to stop the
search.
If the end of the tape is reached during a Search, this unit will cancel
the search and rewind the tape.
Other operations
VCR
VCR
First:
To cue or review picture during playback (Picture Search):
Press g/h buttons during playback. Press it again and the unit will search in super high speed. (in the SLP mode only)
To freeze the picture on TV screen during playback (Still mode):
Press PAUSE F button. Each time you press the button, the picture will be forwarded by one frame.
If the picture begins to vibrate vertically during the still mode, stabilize the picture by pressing the CHANNEL K/L or CHK/CHL buttons. If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if equipped.
Counter Reset:
Press CLEAR/C.RESET button.
To playback in slow motion:
Press SLOW button during playback or the still mode. If the noise bars appear on the TV screen, you can reduce it by pressing CHANNEL K/L or CHK/CHL buttons.
When you playback a tape recorded in Hi-Fi stereo:
Press AUDIO button on the remote control to select Hi-Fi or MONO for playback sound mode.
• If you have connected a stereo TV to this unit, select “HIFI”.
• If you have connected a monaural TV to this unit, select “MONO”.
VCR
Note
•Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the video head.
•To return to playback from the Picture Search/Still/Slow
mode, press PLAY button.
Monaural
L
Main audio
program
Second audio
program
HIFI
R-channelL-channel
Monaural
Main audio
program
Second audio
program
R
Your Selection
Type of recorded tape
non Hi-Fi tapes
Hi-Fi tapes
recorded in
Hi-Fi stereo
Hi-Fi tapes
recorded main
audio program
Hi-Fi tapes
recorded second
audio program
MONO
Monaural
L+R
Main audio
program
Second audio
program
100
Loading...