Funai DPVR-6630-D Service manual
SERVICE MANUAL
Main Section
I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA’s
I Exploded views
I Parts List
DVD PLAYER &VIDEO
CASSETTE RECORDER
DDVR-6830D/DPVR-6630D
When servicing the deck mechanism,
refer to MK14 Deck Mechanism
Section.
Deck Mechanism Part No.:
DDVR-6830D/DPVR-6630D: N25E0FL
DDVR-6530D: N25C0FL
DDVR-6530D
PAL
MAIN SECTION
DVD PLAYER &
VIDEO CASSETTE RECORDER
DDVR-6830D
DDVR-6530D
DPVR-6630D
Main Section
I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA’s
I Exploded Views
I Parts List
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1
Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1
Preparation for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1
Cabinet Disassembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1
How to Initialize the DVD Player & VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1
Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1
Function Indicator Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1
Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1
Wiring Diagram < VCR Section > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1
Wiring Diagram < DVD Section > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-2
IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1
Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1
Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1
Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1
Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19-1
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
SPECIFICATIONS
< VCR Section >
Description Unit Minimum Nominal Maximum Remark
1. Video
1-1. Video Output (PB) Vp-p 0.8 1.0 1.2 SP Mode
1-2. Video Output (R/P) Vp-p 0.8 1.0 1.2
1-3. Video S/N Y (R/P) dB 40 45
1-4. Video Color S/N AM (R/P) dB 37 41 SP Mode
1-5. Video Color S/N PM (R/P) dB 30 36 SP Mode
1-6. Resolution (PB) Line 230 245 SP Mode
2. Servo
2-1. Jitter Low µsec 0.07 0.12 SP Mode
2-2. Wow & Flutter % 0.3 0.5 SP Mode
3. Normal Audio
3-1. Output (PB) dBV -9 -4 -3 SP Mode
3-2. Output (R/P) dBV -9 -4 -1.5 SP Mode
3-3. S/N (R/P) dB 36 41 SP Mode
3-4. Distortion (R/P) % 1.0 4.0 SP Mode
3-5. Freq. resp (R/P) at 200Hz dB -6 -2 SP Mode
(-20dB ref. 1kHz) at 8kHz dB -8 -2 SP Mode
SP Mode,
W/O Burst
4. Tuner
4-1. Video output Vp-p 0.8 1.0 1.2 E-E Mode
4-2. Video S/N dB 39 44 E-E Mode
4-3. Audio output dB -10 -6 -2 E-E Mode
4-4. Audio S/N dB 40 46 E-E Mode
5. Hi-Fi Audio [DDVR-6830D/DPVR-6630D]
5-1. Output dBV -12 -9 -4 SP Mode
5-2. Dynamic Range dB 70 85 SP Mode
5-3. Freq. resp (6dB B.W) Hz 20 ~ 20K SP Mode
Note: Nominal specs represent the design specs. All units should be able to approximate these – some will
exceed and some may drop slightly below these specs. Limit specs represent the absolute worst condition that
still might be considered acceptable; In no case should a unit fail to meet limit specs.
1-1-1 H99A7SP
< DVD Section >
ITEM CONDITIONS UNIT NOMINAL LIMIT
1. Video Output 75 Ω load Vpp 1.0 ± 0.1
2. Optical Digital Out dBm -18
3. Audio (PCM)
3-1. Output Level 1 kHz 0 dB, 47k Ω load Vrms 2.0
3-2. S/N 47k Ω load dB 90
3-3. Freq. Response
DVD fs = 48 kHz ± 0.5dB, 47k Ω load Hz 20~22 k
CD fs = 44.1 kHz ± 0.5dB, 47k Ω load Hz 20~20 k
3-4. THD+N
DVD 1 kHz 0dB, 47k Ω load % 0.01
CD 1 kHz 0dB, 47k Ω load % 0.01
NOTES:
1. All Items are measured without pre-emphasis unless otherwise specified.
2. Power supply : 220 - 240 V ~ 50 Hz
3. Ambient temperature : 5
°C ~ 40 °C
1-1-2 H99A7SP
LASER BEAM SAFETY PRECAUTIONS
This DVD player uses a pickup that emits a laser beam.
Do not look directly at the laser beam coming
from the pickup or allow it to strike against your
skin.
The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep
your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser
beam.
CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in
hazardous radiation exposure.
Drive Mechanism
Assembly
Laser Beam Radiation
Laser Pickup
Turntable
CAUTION- CLASS
-
TION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS
1M
LASER RADIA
-
Location: Top of DVD mechanism.
1-2-1 E6P_LASER
IMPORTANT SAFETY PRECAUTIONS
Product Safety Notice
Some electrical and mechanical parts have special
safety-related characteristics which are often not evident from visual inspection, nor can the protection
they give necessarily be obtained by replacing them
with components rated for higher voltage, wattage,
etc. Parts that have special safety characteristics are
identified by a ! on schematics and in parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might create shock, fire, and/or other
hazards. The Product’s Safety is under review continuously and new instructions are issued whenever
appropriate. Prior to shipment from the factory, our
products are carefully inspected to confirm with the
recognized product safety and electrical codes of the
countries in which they are to be sold. However, in
order to maintain such compliance, it is equally important to implement the following precautions when a set
is being serviced.
Precautions during Servicing
A. Parts identified by the ! symbol are critical for
safety. Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1)Wires covered with PVC tubing
2)Double insulated wires
3)High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1)Insulation tape
2)PVC tubing
3)Spacers
4)Insulators for transistors
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat produc-
ing parts (heatsinks, oxide metal film resistors, fusible resistors, etc.).
G. Check that replaced wires do not contact sharp
edges or pointed parts.
H. When a power cord has been replaced, check that
5 - 6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Be careful that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. Crimp type wire connector
The power transformer uses crimp type connectors
which connect the power cord and the primary side
of the transformer. When replacing the transformer,
follow these steps carefully and precisely to prevent shock hazards.
Replacement procedure
1)Remove the old connector by cutting the wires at a
point close to the connector.
Important: Do not re-use a connector. (Discard it.)
2)Strip about 15 mm of the insulation from the ends
of the wires. If the wires are stranded, twist the
strands to avoid frayed conductors.
3)Align the lengths of the wires to be connected.
Insert the wires fully into the connector.
4)Use a crimping tool to crimp the metal sleeve at its
center. Be sure to crimp fully to the complete closure of the tool.
L. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC outlet.
1-3-1 DVD_SFNP
Safety Check after Servicing
Examine the area surrounding the repaired location
for damage or deterioration. Observe that screws,
parts, and wires have been returned to their original
positions. Afterwards, do the following tests and confirm the specified values to verify compliance with
safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d’) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1 : Ratings for selected area
AC Line Voltage Clearance Distance (d), (d’)
Chassis or Secondary Conductor
Primary Circuit Terminals
dd'
220 to 240 V
Note: This table is unofficial and for reference only.
Be sure to confirm the precise values.
≥ 3 mm(d)
≥ 6 mm(d’)
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs)
and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and
output terminals, microphone jacks, earphone jacks,
etc.) is lower than or equal to the specified value in the
table below.
Measuring Method (Power ON) :
Insert load Z between B (earth ground, power cord
plug prongs) and exposed accessible parts. Use an
AC voltmeter to measure across the terminals of load
Z. See Fig. 2 and the following table.
Exposed Accessible Part
Z
One side of
B
Power Cord Plug Prongs
Fig. 1
AC Voltmeter
(High Impedance)
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line Voltage Load Z Leakage Current (i)
2kΩ RES.
Connected in
220 to 240 V
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
parallel
50kΩ RES.
Connected in
parallel
i≤0.7mA AC Peak
i≤2mA DC
i≤0.7mA AC Peak
i≤2mA DC
1-3-2 DVD_SFNP
One side of power cord plug
prongs (B) to:
RF or
Antenna terminals
A/V Input, Output
STANDARD NOTES FOR SERVICING
Circuit Board Indications
1. The output pin of the 3 pin Regulator ICs is indicated as shown.
Top View
Input
Out
2. For other ICs, pin 1 and every fifth pin are indicated
as shown.
In
Pin 1
3. The 1st pin of every male connector is indicated as
shown.
Bottom View
5
10
Pb (Lead) Free Solder
When soldering, be sure to use the Pb free solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:.
(1) Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
Fig. S-1-1
Pin 1
Instructions for Connectors
1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect
the AC cord.
2. FFC (Flexible Foil Connector) cable should be
inserted parallel into the connector, not at an angle.
FFC Cable
Connector
CBA
(2) Remove the flat pack-IC with tweezers while apply-
ing the hot air.
(3) Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
(4) Release the flat pack-IC from the CBA using twee-
zers. (Fig. S-1-6)
Caution:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage to
the chip parts may occur. Put masking tape around
the flat pack-IC to protect other parts from damage.
(Fig. S-1-2)
* Be careful to avoid a short circuit.
1-4-1 DVD_NOTE
3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when removing
it.
Hot-air
Flat Pack-IC
Desoldering
Machine
CBA
With Soldering Iron:
(1) Using desoldering braid, remove the solder from all
pins of the flat pack-IC. When you use solder flux
which is applied to all pins of the flat pack-IC, you
can remove it easily. (Fig. S-1-3)
Flat Pack-IC
Desoldering Braid
Masking
Tape
Tweezers
Flat Pack-IC
Fig. S-1-2
Soldering Iron
Fig. S-1-3
(2) Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
(3) Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
(4) Release the flat pack-IC from the CBA using twee-
zers. (Fig. S-1-6)
With Iron Wire:
(1) Using desoldering braid, remove the solder from all
pins of the flat pack-IC. When you use solder flux
which is applied to all pins of the flat pack-IC, you
can remove it easily. (Fig. S-1-3)
(2) Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
(3) While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
1-4-2 DVD_NOTE
(4) Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
(5) Release the flat pack-IC from the CBA using twee-
zers. (Fig. S-1-6)
Note:
When using a soldering iron, care must be taken
to ensure that the flat pack-IC is not being held by
glue. When the flat pack-IC is removed from the
CBA, handle it gently because it may be damaged
if force is applied.
2. Installation
(1) Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
(2) The “I” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the 1
on the PCB when positioning for installation. Then
presolder the four corners of the flat pack-IC. (See
Fig. S-1-8.)
(3) Solder all pins of the flat pack-IC. Be sure that none
of the pins have solder bridges.
To Solid
Mounting Point
CBA
Hot Air Blower
Iron Wire
Soldering Iron
Fig. S-1-5
Fine Tip
Soldering Iron
Example :
or
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Fig. S-1-7
Presolder
Flat Pack-IC
CBA
Fig. S-1-8
Tweezers
Flat Pack-IC
Fig. S-1-6
1-4-3 DVD_NOTE
Instructions for Handling
Semi-conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1MΩ) that is properly grounded to remove any static electricity that may
be charged on the body.
2. Ground for Workbench
(1) Be sure to place a conductive sheet or copper plate
with proper grounding (1MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
< Incorrect >
< Correct >
1MΩ
CBA
Grounding Band
1MΩ
CBA
Conductive Sheet or
Copper Plate
1-4-4 DVD_NOTE
PREPARATION FOR SERVICING
How to Enter the Service Mode
About Optical Sensors
Caution:
An optical sensor system is used for the Tape Start
and End Sensors on this equipment. Carefully read
and follow the instructions below. Otherwise the unit
may operate erratically.
What to do for preparation
Insert a tape into the Deck Mechanism Assembly and
press the PLAY button. The tape will be loaded into
the Deck Mechanism Assembly. Make sure the power
is on, connect TP501 (S-INH) to GND. This will stop
the function of Tape Start Sensor, Tape End Sensor
and Reel Sensors. (If these TPs are connected before
plugging in the unit, the function of the sensors will
stay valid.) See Fig. 1.
Note: Because the Tape End Sensors are inactive, do
not run a tape all the way to the start or the end of the
tape to avoid tape damage.
Q503
TP501 S-INH
Q504
Fig. 1
1-5-1 H9700PFS
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and
dress the cables as they were originally.
[1] Top Case
[2] Front Assembly
[3] Top Bracket
[4] DVD Mechanism Assembly
[5] Partition Plate
[6] Power Supply CBA
[7] Loader Holder
[9] VCR Chassis Unit
[10] Deck Assembly
[11] DVD Open/Close CBA
[12] Main CBA
[13] Jack-A CBA
[8] DVD Main CBA Unit
2. Disassembly Method
REMOVAL
LOC.
No.
PART
REMOVE/*UNHOOK/
Fig.
UNLOCK/RELEASE/
No.
UNPLUG/DESOLDER
Note
REMOVAL
ID/
LOC.
No.
[9]
[10]
[11]
[12] Main CBA D6 ---------- -
[13] Jack-A CBA D6 Desolder, 6(S-13) -
↓
(1)
Note:
(1): Identification (location) No. of parts in the figures
(2): Name of the part
(3): Figure Number for reference
(4): Identification of parts to be removed, unhooked,
(5): Refer to “Reference Notes.”ID/
PART
VCR
Chassis Unit
Deck
Assembly
DVD Open/
Close CBA
↓
(2)
unlocked, released, unplugged, unclamped, or
desoldered.
P=Spring, L=Locking Tab, S=Screw,
CN=Connector
*=Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
REMOVE/*UNHOOK/
Fig.
UNLOCK/RELEASE/
No.
UNPLUG/DESOLDER
5(S-8), 2(S-9), (S-10),
D5
(L-3)
Desolder,
D6
2(S-11), (S-12)
D6 Desolder -
↓
(3)
↓
(4)
Note
-
4,5
↓
(5)
[1] Top Case D1 8(S-1) -
Front
[2]
Assembly
[3] Top Bracket D2 3(S-2) -
DVD
[4]
Mechanism
Assembly
Partition
[5]
Plate
Power
[6]
Supply CBA
Loader
[7]
Holder
DVD Main
[8]
CBA Unit
D2 *3(L-1), *3(L-2)
4(S-3), *CN401,
D3
*CN601
D3 (S-4) -
D3 2(S-5), CN501 -
D3 2(S-6) -
2(S-7), *CN201,
D4
*CN301
1-1
1-2
2-1
2-2
1
-
2
3
1-6-1 H97L7DC
Reference Notes
CAUTION 1: Locking Tabs (L-1) and (L-2) are fragile.
Be careful not to break them.
1-1. Release three Locking Tabs (L-1).
1-2. Release three Locking Tabs (L-2), then remove
the Front Assembly.
CAUTION 2: Electrostatic breakdown of the laser
diode in the optical system block may occur as a
potential difference caused by electrostatic charge
accumulated on cloth, human body etc., during
unpacking or repair work.
To avoid damage of pickup follow next procedures.
2-1. Disconnect Connector (CN301). Remove a
Screw (S-7) and lift the DVD Main CBA Unit. (Fig.
D4)
2-2. Short the three short lands of FPC cable with sol-
der before removing the FFC cable (CN201) from
it. If you disconnect the FFC cable (CN201), the
laser diode of pickup will be destroyed. (Fig. D4)
CAUTION 3: When reassembling, confirm the FFC
cable (CN201) is connected completely. Then remove
the solder from the three short lands of FPC cable.
(Fig. D4)
4. When reassembling, solder wire jumpers as shown
in Fig. D6.
5. Before installing the Deck Assembly, be sure to
place the pin of LD-SW on Main CBA as shown in
Fig. D6. Then, install the Deck Assembly while
aligning the hole of Cam Gear with the pin of LDSW, the shaft of Cam Gear with the hole of LD-SW
as shown in Fig. D6.
(S-1)
(L-1)
(S-1)
[1] Top Case
(S-1)
(S-1)
Fig. D1
(S-2)
[3] Top Bracket
(S-2)
(L-2)
(L-1)
[2] Front
Assembly
Fig. D2
1-6-2 H97L7DC
[4] DVD
Mechanism
Assembly
[5] Partition Plate
(S-6)
[7] Loader
Holder
(S-3)
CN501
CN401
CN601
(S-4)
[6] Power
Supply CBA
(S-3)
(S-5)
(S-3)
(S-8)
(S-8)
(S-10)
(S-9)
(S-8)
(S-9)
[9] VCR Chassis Unit
(L-3)
(S-7)
[8] DVD Main
CBA Unit
CN301
A
DVD Mechanism
Short the three short lands by soldering.
(Either of two places.)
Fig. D5
Fig. D3
(S-7)
CN201
Connector
View for A
Fig. D4
1-6-3 H97L7DC
[10] Deck
Assembly
FE Head
Cylinder
Assembly
ACE Head
Assembly
Pin
[12] Main CBA
[11] DVD
Open/Close CBA
(S-11)
Lead with blue stripe
[13] Jack-A CBA
(S-11)
Desolder
from bottom
(S-12)
Desolder
Lead with
blue stripe
(S-13)
(S-13)
From
ACE Head
Assembly
[12] Main CBA
[10] Deck Assembly
Shaft
Hole
LD-SW
Lead with
blue stripe
Lead with
blue stripe
From
Cylinder
Assembly
Desolder
From
FE Head
SW507
LD-SW
Cam Gear
Hole
Pin
[12] Main CBA
Lead with
red stripe
Desolder
Printing side
From
Capstan
Motor
Assembly
Desolder
BOTTOM VIEW
Lead connections of Deck Assembly and Main CBA
1-6-4 H97L7DC
Fig. D6
HOW TO EJECT MANUALLY
1. Remove the Top Case, Front Assembly and Top Bracket.
2. Remove four Screws (S-3) in Fig. D3. Do not disconnect connectors.
3. While lifting up the DVD Mechanism, rotate the roulette in the direction of the arrow as
shown below.
4. Pull the tray slowly manually.
View for A
Rotate this roulette in
the direction of the arrow
DVD Mechanism
A
1-6-5 H97L7DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
c
General Note: "CBA" is an abbreviation for
"Circuit Board Assembly."
NOTE:
1.Electrical adjustments are required after replacing
circuit components and certain mechanical parts.
It is important to do these adjustments only after
all repairs and replacements have been completed. Also, do not attempt these adjustments
unless the proper equipment is available.
2.To perform these alignment / confirmation procedures, make sure that the tracking control is set in
the center position: Press either "CHANNEL L5??" or
"CHANNEL K" button on the front panel first, then
the "PLAY" button on the front panel.
Test Equipment Required
1.Oscilloscope: Dual-trace with 10:1 probe,
V-Range: 0.001~50V/Div.,
F-Range: DC~AC-20MHz
2.Alignment Tape (FL6A)
Head Switching Position Adjustment
Figure 1
EXT. Syncronize Trigger Point
CH1
CH2
Reference Notes:
Playback the Alignment tape and adjust VR501 so that
the V-sync front edge of the CH1 video output waveform is at the 6.5H±1H (416µs±64µs) delayed position
from the rising edge of the CH2 head switching pulse
waveform.
1.0H
6.5H±1H (416µs±64µs)
Switching Pulse
0.5H
V-Syn
Purpose:
To determine the Head Switching position during
playback.
Symptom of Misadjustment:
May cause Head Switching noise or vertical jitter
in the picture.
Test point Adj.Point Mode Input
TP751(V-OUT)
TP504(RF-SW)
GND
Tape
FL6A Oscilloscope
Connections of Measurement Equipment
Main CBA
VR501
(Switching Point)
(MAIN CBA)
Measurement
Equipment
TP751
GND
TP504
PLAY
(SP)
Spec.
6.5H±1H
(416µs±64µs)
Oscilloscope
-----
CH1 CH2
Trig. (+)
1-7-1 H9700EA
HOW TO INITIALIZE THE DVD PLAYER & VCR
To put the program back at the factory-default,
initialize the DVD player & VCR as the following
procedure.
< DVD Section >
1. Press [DVD], [1], [2], [3], [4], and [DISPLAY]
buttons on the remote control unit in that order.
Fig. a appears on the screen.
"
" differ depending on the models.
*******
MODEL : *******
Version
Region
: *.**
: *
EXIT: POWEREEPROM CLEAR : CLEAR
Fig. a
"
" differ depending on the models.
*******
2. Press [CLEAR] button on the remote control unit.
Fig. b appears on the screen.
MODEL : *******
Version
Region
: *.**
: *
EXIT: POWEREEPROM CLEAR : CLEAR
EEPROM CLEAR : OK
Fig. b
When “OK” appears on the screen, the factory
default will be set.
3. To exit this mode, press [STANDBY-ON] button.
1-8-1 H97H4INT
FIRMWARE RENEWAL MODE
[DDVR-6830D/DPVR-6630D]
1. Turn the power on and remove the disc on the tray.
2. To put the DVD player into version up mode, press
[DVD], [9], [8], [7], [6], and [SEARCH MODE]
buttons on the remote control unit in that order.
The tray will open automatically.
Fig. a appears on the screen and Fig. b appears
on the VFD.
"
" differ depending on the models.
*******
(*2)
"
" differ depending on the models.
*******
F/W Version Up Mode
VERSION : ************.ab6
Completed
SUM : 7ABC
Model No : *******
VERSION : *.**
F/W Version Up Mode Model No : *******
Please insert a DISC
for F/W Version Up.
VERSION : *.**
EXIT: POWER
Fig. a Version Up Mode Screen
Fig. b VFD in Version Up Mode
The DVD player can also enter the version up
mode with the tray open. In this case, Fig. a will be
shown on the screen while the tray is open.
3. Load the disc for version up.
4. The DVD player enters the F/W version up mode
automatically. Fig. c appears on the screen and
Fig. d appears on the VFD. If you enter the F/W for
different models, “Disc Error” will appear on the
screen, then the tray will open automatically.
"
" differ depending on the models.
*******
Fig. e Completed Program Mode Screen
Fig. f VFD upon Finishing the Programming Mode (Example)
At this time, no button is available.
6. Remove the disc on the tray.
7. Unplug the AC cord from the AC outlet. Then plug
it again.
8. Turn the power on by pressing the [STANDBY-ON]
button and the tray will close.
9. Press [DVD], [1], [2], [3], [4], and [DISPLAY]
buttons on the remote control unit in that order.
Fig. g appears on the screen.
"
" differ depending on the models.
*******
MODEL : *******
Version
Region
: *.**
: *
(*1)
F/W Version Up Mode Model No : *******
VERSION : ************.ab6
Reading...
VERSION : *.**
Fig. c Programming Mode Screen
Fig. d VFD in Programming Mode (Example)
The appearance shown in (*1) of Fig. c is
described as follows:
No. Appearance State
1 Reading... Sending files into the memory
2 Erasing... Erasing previous version data
3 Programming... Writing new version data
5. After programming is finished, the tray opens
automatically. Fig. e appears on the screen and
the checksum in (*2) of Fig. e appears on the VFD
(Fig. f).
EXIT: POWEREEPROM CLEAR : CLEAR
Fig. g
10. Press [CLEAR] button on the remote control unit.
Fig. h appears on the screen.
"
" differ depending on the models.
*******
MODEL : *******
Version
Region
: *.**
: *
EXIT: POWEREEPROM CLEAR : CLEAR
EEPROM CLEAR : OK
Fig. h
When “OK” appears on the screen, the factory
default will be set. Then the firmware renewal
mode is complete.
11. To exit this mode, press [STANDBY-ON] button.
1-9-1 H99A7FW
[DDVR-6530D]
1. Turn the power on and remove the disc on the tray.
2. To put the DVD player into version up mode, press
[DVD], [9], [8], [7], [6], and [SEARCH MODE]
buttons on the remote control unit in that order.
The tray will open automatically.
Fig. a2 appears on the screen.
"
" differ depending on the models.
*******
F/W Version Up Mode Model No : *******
Please insert a DISC
for F/W Version Up.
VERSION : *.**
EXIT: POWER
Fig. a2 Version Up Mode Screen
The DVD player can also enter the version up
mode with the tray open. In this case, Fig. a2 will
be shown on the screen while the tray is open.
3. Load the disc for version up.
4. The DVD player enters the F/W version up mode
automatically. Fig. c2 appears on the screen. If
you enter the F/W for different models, “Disc Error”
will appear on the screen, then the tray will open
automatically.
"
" differ depending on the models.
*******
"
" differ depending on the models.
*******
(*2)
F/W Version Up Mode
VERSION : ************.ab6
Completed
SUM : 7ABC
Model No : *******
VERSION : *.**
Fig. e2 Completed Program Mode Screen
At this time, no button is available.
6. Remove the disc on the tray.
7. Unplug the AC cord from the AC outlet. Then plug
it again.
8. Turn the power on by pressing the [STANDBY-ON]
button and the tray will close.
9. Press [DVD], [1], [2], [3], [4], and [DISPLAY]
buttons on the remote control unit in that order.
Fig. g2 appears on the screen.
"
" differ depending on the models.
*******
MODEL : *******
Version
Region
: *.**
: *
(*1)
F/W Version Up Mode Model No : *******
VERSION : ************.ab6
Reading...
VERSION : *.**
Fig. c2 Programming Mode Screen
The appearance shown in (*1) of Fig. c2 is
described as follows:
No. Appearance State
1 Reading... Sending files into the memory
2 Erasing... Erasing previous version data
3 Programming... Writing new version data
5. After programming is finished, the tray opens
automatically. Fig. e2 appears on the screen and
the checksum will be shown in (*2) of Fig. e2.
EXIT: POWEREEPROM CLEAR : CLEAR
Fig. g2
10. Press [CLEAR] button on the remote control unit.
Fig. h2 appears on the screen.
"
" differ depending on the models.
*******
MODEL : *******
Version
Region
: *.**
: *
EXIT: POWEREEPROM CLEAR : CLEAR
EEPROM CLEAR : OK
Fig. h2
When “OK” appears on the screen, the factory
default will be set. Then the firmware renewal
mode is complete.
11. To exit this mode, press [STANDBY-ON] button.
1-9-2 H99A7FW
FUNCTION INDICATOR SYMBOLS
Note:
If a mechanical malfunction occurs, the power is turned off. When the power comes on again after that by
pressing [STANDBY-ON] button, an error message is displayed on the TV screen for 5 seconds.
MODE INDICATOR ACTIVE
When reel or capstan mechanism is not
functioning correctly
When tape loading mechanism is not functioning correctly
When cassette loading mechanism is not
functioning correctly
When the drum is not working properly
P-ON Power safety detection
“A R” is displayed on a TV screen. (Refer to Fig. 1.)
“A T” is displayed on a TV screen. (Refer to Fig. 2.)
“A C” is displayed on a TV screen. (Refer to Fig. 3.)
“A D” is displayed on a TV screen. (Refer to Fig. 4.)
“A P” is displayed on a TV screen. (Refer to Fig. 5.)
TV screen
When reel or capstan mechanism is not functioning
correctly
A
R
Fig. 1
When the drum is not working properly
A
D
Fig. 4
When tape loading mechanism is not functioning correctly
A
T
Fig. 2
When cassette loading mechanism is not functioning
correctly
A
C
Fig. 3
P-ON Power safety detection
A
P
Fig. 5
1-10-1 H97H4FIS
BLOCK DIAGRAMS <VCR SECTION>
Servo / System Control Block Diagram
A
B
C
TO AUDIO
BLOCK DIAGRAM
Model Mark
DPVR-6630D
DDVR-6830D
Comparison Chart of
Models & Marks
DDVR-6530D
Q507
D505
AL+5V
POWER
Q508
DVD
D502
Q509
VCR
D503
TIMER
D501
Q502
REC
D504
Q511
SDA
SCL
IC502 (MEMORY)
5
6
TP501
SENS-INH
IIC-BUS SCL
IIC-BUS SDA
AUDIO-MUTE-H
KEY SWITCH
KEY SWITCH
IIC-BUS SDA
TO Hi-Fi AUDIO
BLOCK DIAGRAM
A-MODE
Hi-Fi-H-SW
IIC-BUS SCL
LINE-MUTE
AUDIO-SW1
AUDIO-SW2
OUTPUT SELECT
TO AUDIO
BLOCK DIAGRAM
FRONT-AV
IIC-BUS SCL
IIC-BUS SDA
OUTPUT SELECT
RF-SW
D-REC-H
TO VIDEO
BLOCK DIAGRAM
H-A-SW
C-ROTA
D-V-SYNC
V-ENV
H-A-COMP
OUTPUT-SELECT
C-SYNC
INPUT-SELECT
TO DVD SYSTEM
CONTROL BLOCK
DIAGRAM
<DVD SECTION>
DVD-POWER
OUTPUT-SELECT
A,C
29
DVD-LED
POWER-LED
ST-S
CTL(-)
END-S
949510480
T-REEL
CTL(+)
LD-SW9
IC501
(SERVO/SYSTEM CONTROL)
MAIN CBA
AL+5V
LD-SW
SW507
TP502
CN504
5 CTL(+)
6 CTL(-)
302325
VCR-LED
S-REEL79
PS502
Q506
END-S
B
Q515
S-REEL
T-REEL
TIMER-LED
A,C
DRV-CLK
RESET
34
706869
RESET
DISPLAY-CLK
TIMER+5V
AL+5V
26
REC-LED
DISPLAY-DATA
TO DVD SYSTEM
8
KEY- 2
DRV-DATA
DRV-STB
REMOCON-IN
14
DISPLAY-STB
REMOCON-IN
CONTROL /SERVO
BLOCK DIAGRAM
<DVD SECTION>
S-LED
D555
7
83
KEY- 1
AUDIO-
MUTE-H
DVD-8PIN-IN
42
DVD-8PIN-IN
TO DVD VIDEO/
AUDIO BLOCK
DIAGRAM
<DVD SECTION>
86
19
A-MODE
Hi-Fi-H-SW
A,C
CTL
97
CTL
TP503
AL+5V
28
62
LINE-MUTE
AUDIO-SW1
B
PG-DELAY
2
AL+5V
VR501
SW-POINT
20
63
FRONT-AV
AUDIO-SW2
REC-SAF-SW
31
SW506
REC-SAFETY
CN502
CAPSTAN MOTOR
71
18
33
72
RF-SW
D-REC-H
IIC-BUS SCL
IIC-BUS SDA
C-FG
C-F/R
87
78
P-ON+5V
AL+20.5V/+12V
AL+20.5V/+12V
C-F/R5C-CONT6GND7LM-FWD/REV
1
2 P-ON+5V
3 C-FG
4
13
15
17
16
H-A-SW
C-ROTA
D-V-SYNC
H-A-COMP
LM-
FWD/REV81D-CONT77
C-CONT
76
D-CONT9D-PFG10GND11AL+12V(2)12P-ON+15V
8
MOTOR
DRIVE
CIRCUIT
CAPSTAN
MOTOR
6
41
58
82
V-ENV
C-SYNC
INPUT-SELECT
OUTPUT-SELECT
D-PFG
90
AL+12V(2)
P-ON+15V
M
M
21
DVD-POWER
P-ON-H
C-POW-SW
67
66
32 P-DOWN-H
P-ON-H
C-POW-SW
P-DOWN-H
TO POWER
SUPPLY BLOCK
DIAGRAM
CONTROL
ACE HEAD ASSEMBLY
(DECK ASSEMBLY)
HEAD
Q504
ST-S
SENSOR CBA
Q503
1-11-1
END-S
SENSOR CBA
M
PG
SENSOR
DRUM
CYLINDER ASSEMBLY
MOTOR
LOADING
MOTOR
H99A7BLS
Video Block Diagram
A
B
C
Model Mark
DPVR-6630D
DDVR-6830D
Comparison Chart of
Models & Marks
DDVR-6530D
VIDEO (R)-1
HEAD
CYLINDER ASSEMBLY
(DECK ASSEMBLY)
123
VIDEO (L)-1
HEAD
VIDEO (L)-2
HEAD
456
VIDEO (R)-2
HEAD
TO SERVO/SYSTEM
CONTROL BLOCK
DIAGRAM
MODE: SP/RECPB-VIDEO SIGNAL DVD VIDEO SIGNAL
MAIN CBA
TO SERVO/SYSTEM
CONTROL BLOCK
DIAGRAM
REC-VIDEO SIGNAL
IIC-BUS SCL
IIC-BUS SDA
CN251
VIDEO(L)-2
VIDEO(L)-1
VIDEO(R)-1
VIDEO-COM
969594
7978
46 43
6968
SERIAL
DECORDER
65
P
R
Y. DELAY
VIDEO-COM
93
SP
HEAD
AMP
SP
EP
LUMINANCE
SIGNAL
PROCESS
AGC
VIDEO(R)-2
908988
WF1
EP
RF-SW
D-REC-H
RF-SW
TP504
87
80
HEAD
AMP
D-REC-H
REC FMAGC
+
Y
C
CCD 1H DELAY
1/2
FBC
CHARA.
INS.
C-ROTA
V-ENV
H-A-SW
D-V-SYNC
H-A-COMP
84
83
71
62
70
V-ENV
H-A-SW
D-V-SYNC
H-A-COMP
RF-SW/C-ROTA
RPRP
CHROMINANCE
SIGNAL
PROCESS
PR
C-SYNC
67
C-SYNC
Y/C
MIX
AGC
VXO
21
2928
C-PB
TP301
X301
4.43MHz
WF2
IC501 (OSD)
55
5052
COLOR
OSD
CHARACTER
MIX
(TUNER UNIT)
TU701
-IN
6VIDEO
A,B
VIDEO SIGNAL PROCESS
/HEAD AMP
IC301
J901
B
24
VIDEO OUT
JK752
(SW)
VCR
IC1404
VIDEO
-IN
FRONT
5
4
DVD
3
BYPASS
IN1
TUNER
485052
SW CTL
A,C
IN2
9
1-11-2
FRONT
IN2
PB/EE
FRONT
56
54
INPUT-SELECT
TO
SERVO/SYSTEM
CONTROL BLOCK
DIAGRAM
MUTE
IN1
TUNER
DVD-VIDEO
TO DVD
VIDEO/AUDIO
BLOCK DIAGRAM
<DVD SECTION>
PB/EE
MUTE
JK101
19
VIDEO-OUT1
20
VIDEO-IN1
61
63
8
CN2017
VIDEO-OUT2
8
CN2018
BUFFER
JK1402
19
VIDEO
-OUT2
58 59
Q104
VIDEO-IN2
10 10
Q103
20
VIDEO
-IN2
3
DVD
IC751
(OUTPUT SELECT)
BUFFER
JACK-A CBA
5
SW CTL
V-OUT
TP751
11109
VCR
4
H99A7BLV
TO SERVO/SYSTEM
CONTROL BLOCK DIAGRAM
OUTPUT-SELECT
WF3
Loading...