Fujitsu VFY:T1323SC010IN User Manual
Operating Manual - English
FUJITSU Server PRIMERGY TX1320 M3
Operating Manual
March 2017
Comments… Suggestions… Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
manuals@ts.fujitsu.com.
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright 2017 FUJITSU LIMITED
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.
TX1320 M3 Operating Manual 3
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for Japan: About SATA hard disk drives (HDDs)
The SATA version of this server supports HDDs with SATA / BC-SATA storage
interfaces. Please note that the usage and operation conditions differ
depending on the type of HDD used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of HDD:
http://jp.fujitsu.com/platform/server/primergy/harddisk/
Only for Japan:
Shielded LAN cables should be used in this product.
4 Operating Manual TX1320 M3
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Concept and target groups for this manual . . . . . . . . . . 9
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . 10
1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . 11
2 Functional overview . . . . . . . . . . . . . . . . . . . . . . 13
2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 Server specification . . . . . . . . . . . . . . . . . . . . . . 23
3 Installation steps, overview . . . . . . . . . . . . . . . . . . 31
4 Important information . . . . . . . . . . . . . . . . . . . . . 33
4.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 33
4.2 ENERGY STAR . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.3 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.4 FCC Class A Compliance Statement . . . . . . . . . . . . . 43
4.5 Environmental protection . . . . . . . . . . . . . . . . . . . 44
5 Hardware installation . . . . . . . . . . . . . . . . . . . . . . 47
5.1 Unpacking the server . . . . . . . . . . . . . . . . . . . . . 48
5.2 Setting up the server . . . . . . . . . . . . . . . . . . . . . . 49
5.2.1 Positioning the server vertically . . . . . . . . . . . . . . . . . 50
5.2.2 Positioning the server horizontally . . . . . . . . . . . . . . . . 53
5.3 Connecting devices to the server . . . . . . . . . . . . . . . 54
5.4 Connecting the server to the mains . . . . . . . . . . . . . . 56
5.4.1 Using cable ties (standard PSU) . . . . . . . . . . . . . . . . . 57
5.4.2 Using the cable clamps (hot-plug PSU) . . . . . . . . . . . . . 58
TX1320 M3 Operating Manual
Contents
5.5 Notes on connecting/disconnecting cables . . . . . . . . . . 59
6 Starting up and operation . . . . . . . . . . . . . . . . . . . . 61
6.1 Access to the drives . . . . . . . . . . . . . . . . . . . . . . . 61
6.2 Opening the HDD cover . . . . . . . . . . . . . . . . . . . . . 63
6.3 Controls and indicators . . . . . . . . . . . . . . . . . . . . . 64
6.3.1 Server front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.3.1.1 Controls on the front panel . . . . . . . . . . . . . . . . . . 64
6.3.1.2 Indicators on the front panel . . . . . . . . . . . . . . . . . . 65
6.3.1.3 Indicators on the drives . . . . . . . . . . . . . . . . . . . . 68
6.3.2 Server rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
6.3.2.1 Indicators on the I/O panel . . . . . . . . . . . . . . . . . . 70
6.3.2.2 Indicator on hot-plug PSUs . . . . . . . . . . . . . . . . . . 74
6.3.2.3 Indicator on Fujitsu battery units (FJBU) . . . . . . . . . . . 75
6.4 ID card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
6.5 Switching the server on and off . . . . . . . . . . . . . . . . 77
6.6 Configuring the server . . . . . . . . . . . . . . . . . . . . . 80
6.6.1 Configuring the onboard SATA controller . . . . . . . . . . . . . 80
6.6.2 Configuring the SAS/SATA RAID controller . . . . . . . . . . . . 81
6.6.3 Configuring the server and installing the operating system
with the ServerView Installation Manager . . . . . . . . . . . . . 82
6.6.4 Configuring the server and installing the operating system
without the ServerView Installation Manager . . . . . . . . . . . 83
6.7 Cleaning the server . . . . . . . . . . . . . . . . . . . . . . . 84
7 Property and data protection . . . . . . . . . . . . . . . . . . 85
7.1 Mechanical access protection . . . . . . . . . . . . . . . . . 85
7.2 BIOS Setup security functions . . . . . . . . . . . . . . . . . 85
8 Troubleshooting and tips . . . . . . . . . . . . . . . . . . . . 87
8.1 Power-on indicator remains unlit . . . . . . . . . . . . . . . . 87
8.2 Server switches itself off . . . . . . . . . . . . . . . . . . . . 88
8.3 Screen remains blank . . . . . . . . . . . . . . . . . . . . . . 88
Operating Manual TX1320 M3
Contents
8.4 Flickering stripes on monitor screen . . . . . . . . . . . . . 89
8.5 No screen display or display drifts . . . . . . . . . . . . . . 89
8.6 No mouse pointer displayed on screen . . . . . . . . . . . . 89
8.7 Incorrect date and time . . . . . . . . . . . . . . . . . . . . 90
8.8 Drives reported as “dead” when starting system . . . . . . 90
8.9 Added drive reported as defective . . . . . . . . . . . . . . 90
8.10 Error message on screen . . . . . . . . . . . . . . . . . . . 91
TX1320 M3 Operating Manual
Contents
Operating Manual TX1320 M3
1 Introduction
The PRIMERGY TX1320 M3 server is an Intel-based server for small and
medium-sized networks and can be used in the horizontal position or as a
desktop model.
The PRIMERGY TX1320 M3 server features exceptionally low energy
consumption, very quiet running and a compact size. As a result, it is also the
ideal solution for small offices.
Thanks to its highly developed hardware and software components, the
PRIMERGY TX1320 M3 server offers a high level of data security and
availability. This includes hot-plug HDD modules (2.5-inch variant), the
ServerView Operations Manager for server management, Prefailure Detection
and Analysing (PDA), and Automatic Server Reconfiguration and Restart
(ASR&R).
Security functions in the BIOS-setup protect the data on the server against
manipulation. Additional security is provided by the lockable drive cover.
1.1 Concept and target groups for this manual
This operating manual describes how to install, set up and operate your server.
This operating manual is intended for those responsible for installing the
hardware and ensuring that the system runs smoothly. It contains all the
information you need to put your PRIMERGY TX1320 M3 into operation.
To understand the various expansion options, you will need to be familiar with
the fields of hardware and data transmission and you will require a basic
knowledge of the underlying operating system.
TX1320 M3 Operating Manual 9
Introduction
1.2 Documentation overview
More information on your PRIMERGY TX1320 M3 can be found in the following
documents:
– "Quick Start Hardware - FUJITSU Server PRIMERGY TX1320 M3"
– "ServerView Quick Start Guide"
– "Safety Notes and Regulations" manual
" 安全上のご注意 " for Japan
– "Warranty" manual
" 保証書 " for Japan
– "ServerView Suite Local Service Concept - LSC" manual
– "Returning used devices" manual and "Service Desk" leaflet
" サポート＆サービス " for Japan
– "FUJITSU Server PRIMERGY TX1320 M3 Upgrade and Maintenance
Manual"
– "D3373 BIOS Setup Utility for FUJITSU Server PRIMERGY TX1320 M3
Reference Manual"
I All documentation on PRIMERGY hardware and ServerView software is
available online from the Fujitsu manuals server at:
http://manuals.ts.fujitsu.com
Further sources of information:
– ServerView Suite Glossary
– Manual for the monitor
– Documentation for the boards and drives
– Operating system documentation
– Information files in your operating system
10 Operating Manual TX1320 M3
For Japan:
http://www.fujitsu.com/jp/products/computing/servers/primergy/manual/
The complete PRIMERGY documentation set can also be downloaded
as a DVD ISO image at:
ftp://ftp.ts.fujitsu.com/images/serverview/manuals
For Japan:
http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/
Introduction
1.3 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Ê describes activities that must be performed in the order
shown.
V CAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
I indicates additional information, notes and tips.
TX1320 M3 Operating Manual 11
12 Operating Manual TX1320 M3
Introduction
2 Functional overview
This section provides information on the features and technical data of the
PRIMERGY TX1320 M3 server.
2.1 Features
Intel® Xeon®, Pentium®, or Core™ i3 CPU
The server has an Intel
data processing.
Customer Self Service (CSS)
The PRIMERGY Customer Self Service (CSS) concept enables you to identify
and replace the affected component yourself in the case of certain error
scenarios.
In the CSS concept, you can replace the following components yourself in the
event of an error:
– Hot-plug HDD/SSD modules
– Hot-plug PSUs
– Memory modules
®
Xeon®, Pentium®, or Core™ i3 CPU for high-speed
– System fans
– Expansion cards
For information on replacing these components, see the "FUJITSU Server
PRIMERGY TX1320 M3 Upgrade and Maintenance Manual".
CSS indicators on the control panel and on the back of the PRIMERGY server
provide you with information if a CSS event arises.
In addition, CSS errors are displayed in the ServerView Operations Manager,
the server management software from Fujitsu.
In the event of errors, the ServerView Operations Manager refers you directly
to the affected component and its order information in the Illustrated Spares
catalog of the server in question. (This feature is not available for Japan.)
TX1320 M3 Operating Manual 13
Functional overview
I Further information on the CSS concept is provided in the "PRIMERGY
ServerView Suite Local Service Concept - LSC" manual on the Fujitsu
manuals server.
For the latest information on optional products provided for the
TX1320 M3 see the configurator of the server:
http://ts.fujitsu.com/products/standard_servers/index.html
For Japan:
http://www.fujitsu.com/jp/products/computing/servers/primergy/
System board
The features of the system board are described in the "FUJITSU Server
PRIMERGY TX1320 M3 Upgrade and Maintenance Manual" and in the "D3373
BIOS Setup Utility for FUJITSU Server PRIMERGY TX1320 M3 Reference
Manual" for the firmware.
Trusted Platform Module (TPM)
A Trusted Platform Module (TPM) for safer storage of keys can be implemented
as an option. This module enables programs from third party manufacturers to
store key information (e.g. drive encryption using Windows Bitlocker Drive
Encryption).
The TPM is activated via the BIOS system (for more information, refer to the
“D3373 BIOS Setup Utility for FUJITSU Server PRIMERGY TX1320 M3
Reference Manual").
V CAUTION!
– When using the TPM, note the program descriptions provided by the
third party manufacturers.
– You must also create a backup of the TPM content. To do this, follow
the third party manufacturer's instructions. Without this backup, if the
TPM or the system board is faulty you will not be able to access your
data.
– If a failure occurs, please inform your service about the TPM
activation before it takes any action, and be prepared to provide them
with your backup copies of the TPM content.
14 Operating Manual TX1320 M3
Functional overview
Hard disk drives (HDDs)
The server is shipped with one of the following drive cages:
– For up to two non hot-plug 3.5-inch SATA HDDs:
Up to two 3.5-inch SATA HDD modules can be used in the drive cage. Each
HDD module can accommodate a SATA HDD with a maximum height of 1
inch.
– For up to eight 2.5-inch SAS/SATA HDDs:
Up to four 2.5-inch SAS/SATA HDD modules can be used in each of the two
bays of the drive cage. Each HDD module can accommodate an SAS/SATA
HDD with a 2.5-inch format. The modules are connected to the SAS/SATA
backplane wirelessly. This allows HDD modules to be plugged in or pulled
out easily. If the server has a corresponding RAID configuration, defective
HDD modules can also be replaced during operation.
Onboard SATA controller
A SATA controller is integrated on the system board; up to four SATA HDDs can
be connected to the controller. The LSI Embedded MegaRAID software (SATA
Software RAID) supports RAID levels 0, 1 and 10.
For more information on configuring the controller, see section "Configuring the
onboard SATA controller" on page 80.
TX1320 M3 Operating Manual 15
Functional overview
SAS/SATA RAID controller
The server is available with the following SAS/SATA RAID controllers for
operating the internal SAS/SATA HDDs:
– Modular Host Bus Adapter with "Integrated RAID" (IR).
RAID levels 0 and 1 are supported for internal HDD configurations.
– Modular RAID 0/1 controller with "MegaRAID functionality" (integrated
MegaRAID).
RAID levels 0, 1, 10, 5 and 50 are supported for internal HDD configurations.
– Modular RAID 5/6 controller with "MegaRAID functionality" (MegaRAID).
RAID levels 0, 1, 10, 5, 50, 6 and 60 are supported for internal HDD
configurations. As an option, a flash backup unit (FBU) can save the
memory content even if the power fails. Cache memory size of 1GB or 2GB
are available.
I For more information on configuring the controller, see section
"Configuring the SAS/SATA RAID controller" on page 81.
Further information on SAS/SATA RAID controllers is provided in the
"Modular RAID Controller Installation Guide" (on the Fujitsu manuals
server under x86 Servers - Expansion Cards - Storage Adapters).
Further information on other SAS/SATA RAID controllers (e.g. for
operating external SAS/SATA HDDs or tape drives) is available on the
Fujitsu manuals server under x86 Servers - Expansion Cards - Storage
Adapters - LSI SAS / SCSI Controllers.
Accessible drives
Two mounting locations are available:
– a 3.5-inch bay for a backup drive.
– an ultra slim ODD.
The accessible drives cannot be replaced during operation.
Power supply unit (PSU)
In its basic configuration the server has a standard PSU that adjusts
automatically to any mains voltage in the range 100V - 240V.
In the redundant configuration a hot-plug redundant PSU with two modules
serves as a redundant power supply. If one PSU fails, the second PSU in the
redundant configuration ensures operation can continue uninterrupted.
16 Operating Manual TX1320 M3
Functional overview
Fujitsu battery unit (FJBU)
FJBU behaves as a modular UPS in the server. When power fail happened, the
server can operate by FJBU battery for a while.
FJBU supports hot-plugging, and can be replaced during operation.
You can download the management software (FJBU management software) for
the following OS:
– Windows Server 2012 R2, Windows Server 2012, Windows Server 2016
– Windows Server 2008 R2 SP1, Windows Server 2008 R2 SP2
I FJBU management software is not available in Red Hat Enterprise Linux
environment. Please use the IPMI function at Linux environment.
Advanced Thermal Design
The Advanced Thermal Design option allows you to operate the system with a
wider temperature range of 5 °C to 40 °C, depending on your system and
configuration.
This option can only be ordered from the manufacturer and is
indicated by the respective logo on the identification rating
plate.
V CAUTION
In a system that is configured with Advanced Thermal Design, only
certain components which support the respectively increased higher
operating temperature range may be installed and used. For applicable
restrictions, please refer to the official configurator tool.
TX1320 M3 Operating Manual 17
Functional overview
High level of availability and data security
When memory data is accessed, 1-bit errors are identified in the main memory
and automatically corrected with the error correcting code (ECC) method.
ASR&R (Automatic Server Reconfiguration and Restart) restarts the system in
the event of an error and automatically "hides" the defective system
components.
The PDA (Prefailure Detection and Analysis) technology from Fujitsu analyzes
and monitors all components that are critical for system reliability.
A RAID controller supports different RAID levels and increase the availability
and data security of the system.
The hot-plug HDD modules provide additional availability.
18 Operating Manual TX1320 M3
Functional overview
iRMC S4 with integrated management LAN connector
The iRMC S4 (integrated Remote Management Controller) is a Baseboard
Management Controller (BMC) with integrated management LAN connector
and expanded functionality that was previously only available with additional
plug-in cards. In this way, the iRMC S4 enables complete control of PRIMERGY
servers, regardless of system status, and thus particularly the control of
PRIMERGY servers that are in the "out-of-band" system status.
Major functions supported by the iRMC S4 include the following:
● Browser access via iRMC S4´s own Web server
● Secure communication (SSH, SSL)
● Power Management for the managed server (depending on its system
status)
● Power Consumption Management
● Connecting virtual drives as remote storage
● Text-based and graphic console bypass (Advanced Video Redirection)
● Remote Storage
● Command Line Interface (CLI)
● Simple, interactive or script-based iRMC S4configuration
● Customer Self Service (CSS)
● iRMC S4´s own user management
● Multi-computer, global iRMC S4 user administration using an LDAP
Directory Service
● Automatic network configuration via DNS / DHCP
● Power supply of the iRMC S4 via the system standby supply
● Full-coverage alarm management
● System Event Log (SEL) reading and processing
● IPMI support
● CIM / WS-MAN support
● Internal Event Log for user login / logout auditing
TX1320 M3 Operating Manual 19
Functional overview
More information about the iRMC S4 can be found in the "iRMC S4 - integrated
Remote Management Controller" user guide (on the Fujitsu manuals server
under x86 Servers - Software - ServerView Suite - Out-Of-Band Management).
Server management
Server management is implemented using the ServerView Operations Manager
supplied and the PDA (Prefailure Detection and Analysis) technology from
Fujitsu. PDA reports the threat of a system error or overload at an early stage,
allowing preventive measures to be taken.
The ServerView Operations Manager enables the management of all
PRIMERGY servers in the network via a central console. The ServerView
Operations Manager supports the following functions:
● Round-the-clock monitoring, regardless of server status
● High-performance, graphical console bypass (AVR) protected by
HTTPS/SSL (128 bit)
● Remote storage via USB
● Remote power on
● Intrusion detection in the floorstand model
● Temperature monitoring of the CPU and the surrounding area
● Detailed status and error reports for CPUs and main memory
● Watchdog timer for Automatic Server Reconfiguration and Restart (ASR&R)
in the event that memory modules or CPUs fail
● Power monitoring
● End-of-life monitoring of fans with prompt notification before failure
● Watchdog timer for monitoring the operating system with ASR&R
Further information on the ServerView Operations Manager is provided in the
associated documentation.
20 Operating Manual TX1320 M3
Functional overview
ServerView Installation Manager
You can configure the PRIMERGY server quickly and precisely with the
ServerView Installation Manager software provided. User-guided menus are
available for installing the server operating system (for further details see
section "Configuring the server" on page 80).
Service and support
PRIMERGY servers are easy to maintain and modular, thus enabling quick and
simple maintenance.
The handles and locks (touch points) used to exchange components are
colored green to ensure simple and immediate recognition.
In order to prevent the components from being damaged by incorrect handling
when they are being installed and removed, the areas of all components that
can be touched without damaging them are also marked green.
PRIMERGY diagnostic LEDs fitted on the system board indicate which
component (memory module, CPU, fan or expansion card) is not functioning
properly.
The Flash EPROM program supplied with the Fujitsu utilities supports a fast
BIOS update.
With the iRMC (integrated Remote Management Controller) on the system
board, the PRIMERGY TX1320 M3 server can also be maintained and serviced
remotely. This enables remote diagnosis for system analysis, remote
configuration and remote restart should the operating system or hardware fail.
TX1320 M3 Operating Manual 21
Functional overview
ServerView Remote Management
ServerView Remote Management is the remote management solution from
Fujitsu for PRIMERGY servers. ServerView Remote Management and the
relevant hardware components integrated on the system board allow remote
monitoring and maintenance as well as fast restoration of operation in the event
of errors.
Remote monitoring and maintenance avoids time-consuming and costly on-site
repairs and reduces service costs. This leads to a reduction in the total cost of
ownership and an excellent return on investment for the remote management
solution.
The administrator can access all system information and information from the
sensors such as fan speeds or voltages via the iRMC S4's Web interface (see
section "iRMC S4 with integrated management LAN connector" on page 19).
You can also start the text-based or graphic console bypass (Advanced Video
Redirection, AVR) and connect virtual drives as remote storage.
I More information about the iRMC S4 can be found in the "iRMC S4 -
integrated Remote Management Controller" user guide (on the Fujitsu
manuals server under x86 Servers - Software - ServerView Suite - Out-Of-
Band Management).
22 Operating Manual TX1320 M3
Functional overview
2.2 Server specification
This section explains the specifications for the server. The specifications for this
server are liable to be updated without any notice. Please be forewarned.
System Board
System board type D3373
®
Chipset Intel
CPU
E3-1200V6 and Intel® C236
CPU quantity and type 1x Intel
®
Xeon® E3-1200 v6 (quad-core) / Pentium®
/ Core™ i3
Memory Modules Configuration
Memory slots 4
Memory slot type UDIMM (DDR4)
Memory capacity
4 GB - 64 GB
(min. - max.)
Memory protection ECC
Memory notes Dual channel support. For dual channel
performance, a minimum of 2 memory modules has
to be ordered. Capacity per channel has to be the
same. Memory modules with 4, 8 or 16 GB and 2400
MHz are available.
TX1320 M3 Operating Manual 23
Functional overview
Interfaces
USB connectors 2.0 4x external rear, no USB wake-up supported
USB connectors 3.0 2x external front, no USB wake-up supported
2x external rear, no USB wake-up supported
1x internal for USB backup device
Graphics (15-pin) 1 x VGA
Serial 1 (9-pin) 1 x serial RS-232-C, usable for iRMC or system or
shared
LAN / Ethernet (RJ45) 2 x Intel
Management LAN
(RJ45)
1 x dedicated service LAN port for iRMC S4
(10/100/1000 Mbit/s) Service LAN traffic can be
®
i210 Gbit/s Ethernet
switched to shared onboard Gbit LAN port
Onboard or integrated controllers
RAID Controller Modular Host Bus Adapter with "Integrated RAID"
(IR). RAID levels 0 and 1 are supported for internal
HDD configurations.
Modular RAID 0/1 controller with “MegaRAID
functionality” (integrated MegaRAID). RAID levels 0,
1, 10, 5 and 50 are supported for internal HDD
configurations.
Modular RAID 5/6 controller with "MegaRAID
functionality" (MegaRAID). RAID levels 0, 1, 10, 5,
50, 6 and 60 are supported for internal HDD
configurations.
SATA Controller A 6-port SATA controller is integrated on the system
board; up to four SATA HDDs can be connected to
the controller. The LSI Embedded MegaRAID
software (SATA Software RAID) supports RAID
levels 0, 1 and 10.
Remote Management
Controller
Integrated Remote Management Controller
(iRMC S4), 256 MB DDR3-800 SRAM for video,
IPMI 2.0 compatible
Trusted Platform
Infineon V1.2 / V2.0 compliant (option)
Module (TPM)
24 Operating Manual TX1320 M3
Functional overview
Slots
Slot 1: PCIe Gen3 x1
up to 168 mm length, low profile
(mechanical x4)
Slot 2: PCIe Gen3 x4
notched, up to 168 mm length, low profile
(mechanical x4)
Slots 3, 4: PCIe Gen3 x8
notched, up to 168 mm length, low profile
(mechanical x8)
Slot notes In SAS configuration 1x PCI-Express occupied by
modular RAID controller.
Drive bays
Hard disk bay
configuration
8x 2.5-inch hot-plug SAS/SATA or 2x 3.5-inch non
hot-plug SATA
Accessible drive bays 1x 3.5/1.6-inch for backup devices
Ultra Slim ODD
Notes accessible drives all possible options described in relevant system
configurator
Operating Panel
Operating buttons Reset button
NMI button
ID button
On/Off button
Status LEDs ID indicator (blue)
CSS indicator (orange)
Global Error indicator (orange)
HDD/SSD activity indicator (green)
Power-on indicator (green)
AC connected indicator (green)
TX1320 M3 Operating Manual 25
Functional overview
Dimensions / Weight
Upright operating
position (W x D x H)
Horizontal operating
position (W x D x H)
Weight up to 11 kg
Weight notes Weight may vary depending on actual configuration
Ventilation clearance
At least 200 mm on the front and rear.
Ambient conditions
Environment class 3K2
Environment class 2K2
Temperature:
Operation (3K2) 5°C ... 40°C (with ATD)
Transport (2K2) -25 °C ... 60 °C
Humidity 10% ... 85% (non condensing)
Condensation during operation must be avoided!
193 mm x 438 mm x 360 mm (including feet)
340 mm x 400 mm x 101 mm
EN60721 / IEC 721 Part 3-3
EN60721 / IEC 721 Part 3-2
10°C ... 35°C (without ATD)
26 Operating Manual TX1320 M3
Functional overview
Noise level
SAS systems
(8x 2.5" SAS HDD,
standard PSU)
4.3 B (standby)
4.7 B (operation)
29 dB (A) (standby)
33 dB (A) (operation)
Sound power level L
WAd
(ISO 9296)
Sound pressure level at
adjacent workstation L
pAm
SATA systems
(4x 2.5" HDD,
standard PSU)
3.3 B (standby)
3.5 B (operation)
20 dB (A) (standby)
21 dB (A) (operation)
(ISO 9296)
Declared noise emission
according to ISO 9296
Standby
Operating (ISO 7779)
ETSI 300 753 Class 3.1
Noise level (detailed)
LpAm at
bystander
position
A-weighted
sound
power level
L
WAd
Standby (fan control: standard) 20 dB (A) 3.3 B
Standby (fan control: performance), active with
30 dB (A) 4.5 B
INTEL LAN X540-T2 10 GB
Operation (OLTIS 100), depending on the
22 dB (A) 3.5 B
configuration
Standby (fan control: emergency) 26 dB (A) 4.2 B
High fan speed mode (8x 2.5" SAS HDD,
48 dB (A) 6.2 B
standard PSU)
High fan speed mode (8x 2.5" SAS HDD,
64 dB (A) 7.6 B
redundant PSU)
TX1320 M3 Operating Manual 27
Functional overview
Electrical values of the PSU
Power supply
configurations
Max. output 250 W (standard PSU)
Rated voltage range 100 - 240 V
Rated frequency range 50 - 60 Hz
Rated current 5.0 A - 2.5 A (250 W, AC outlet included)
Main power fuse 16 A
Protection class I
Electrical values of the Fujitsu battery unit (FJBU)
Battery unit
configuration
Max. output 280 W
Backup duration Max. 2 seconds (380W), 4 minutes (280W) with
Charge duration 4 hours to 90%,5 hours to 100%
Battery spec. Nickel Metal-Hydrite battery
Battery life time 5 years
Input/Output voltage 12 V DC
Weight 1.2 kg
1 x standard PSU or 1x redundant PSU with two
hot-plug PSU modules
450 W (redundant PSU)
3 A - 1.5 A (450 W )
1x hot-plug power supply and an FJBU inserted in
slot 2.
FJBU M2
1x per system maximum
28 Operating Manual TX1320 M3
Loading...