Fujitsu SP93GX, SP620C, SP3091DC, SP3092DC, FI-4220C-C2 User Manual

Fujitsu SCSI Scanner Installation Procedures

Windows 95\98\98SE\ME\2000\XP

If you are installing the following models by means of the SCSI interface then use this
document.

SP10C M3093GX\DG Fi-4530C Fi-5120C
SP15C M3096GX Fi-4640S Fi-5220C
SP600C M3097G\G+\DG M4097D Fi-5530C
SP620C M3099G\GX\GH Fi-4750C\L Fi-5650C
SP3091DC FI-4120C\C2 M4099D Fi-5750C
SP3092DC Fi-4220C\C2 Fi-4860C Fi-5900C
SP93GX Fi-4340C Fi-4990C

If you are going to use the USB interface of a dual SCSI/USB model then use the USB scanner
installation guide. For Scansnap models please use the Scansnap installation guide.

Hardware requirements.

You will need a PC system that meets our recommended specifications, an appropriate SCSI
controller, and a SCSI cable (six foot recommended maximum). For recommended PC system
specifications and SCSI controllers please reference the
You may also need your Operating System Disk.

Step A: Installing the SCSI Host Adapter (Adaptec).

1. Shut down your PC and remove the case cover.

2. Locate a free PCI slot and remove the back plate if necessary.

3. Install the SCSI controller in an open PCI slot.
Make sure that the card is seated completely in the slot and secured in the frame

Warning! Failure to secure the SCSI controller in the PC can result in damage to the
SCSI card, scanner, and/or your system.

4. Boot your PC without the scanner attached

Step B: Installing the SCSI drivers (Adaptec).

5. When the New Hardware wizard comes up, allow Windows to finish installing the
hardware files for the SCSI controller.

6. Then either install/update the ASPI drivers from the CD or go to
and click on the “search” tab.

7. For Windows 95\98 or ME scroll down to the “Enter key word or quoted phrase” box
and type in “aspi32”.

8. Next scroll down to the drivers section, click on ASPI32 and follow the prompts to
download it your desktop or a new folder.

9. Afterwards go to that location and double click on the "aspi32.exe" icon and follow
the prompts.

10. When the message “ASPI is up to date” appears, reboot and go to the next step.

Scanner Hardware Reference page.

.

www.adaptec.com,

Rev051906A Page 1 of 7

Fujitsu SCSI Scanner Installation Procedures

Windows 95\98\98SE\ME\2000\XP

11. For Windows 2000 or XP scroll down to the “Enter key word or quoted phrase” box
and type in “aspi”.

12. Next scroll down to the drivers section, click on ASPI_v470 or higher and follow the
prompts to download it.

13. Afterwards go to that folder and unzip the file to the default Adaptec\ASPI folder.

14. Then go to start, run, browse to the Adaptec\ASPI folder, select ASPIINST.EXE and
run it.

15. When the message “ASPI is up to date” appears, reboot and go to the next step.

Step C: Installing the drivers from the Setup CD.

To begin it is recommended that you install the drivers first before connecting the scanner.

Installing the STI-Twain driver.

1. Insert the Scanner Setup CD into your CD Rom.

2. Next please complete the pre-registration box when it appears and click the submit
button.

3. Afterwards close your browser and click the Install Products button on the Scanner
Setup Menu.

4. On the next screen click on Twain Driver and you may be presented with the option
to install the Error Recovery Guide.

5. After you have installed the Error Recovery Guide (or not) follow the prompts to
complete the twain driver installation.

6. Do not reboot at this time!

Installing the ASPI-Twain driver.

Some of our scanners are not supported by the STI-Twain drivers. For those units you
must install the ASPI-Twain driver. Please refer to the driver download page to see if
your model is one of them.

7. Insert the Scanner Setup CD into your CD Rom.

8. Next please complete the pre-registration box when it appears and click the submit
button.

9. Afterwards close your browser and click the Install Products button on the Scanner
Setup Menu.

10. On the next screen click on Twain Driver and you may be presented with the option
to install the Error Recovery Guide.

11. After you have installed the Error Recovery Guide (or not) follow the prompts to
complete the twain driver installation.

12. Do not reboot at this time!

Installing the ISIS driver.

13. Next go back to the Scanner Setup Menu and click on ISIS Driver.

14. If you didn’t install the Error Recovery Guide during the Twain driver installation you
will be asked again. Proceed and follow the prompts to complete the ISIS driver
installation.

15. Do not reboot at this time!

Rev051906A Page 2 of 7

Fujitsu SCSI Scanner Installation Procedures

Windows 95\98\98SE\ME\2000\XP

Installing ScandAll 21.

16. Back to the Scanner Setup Menu and click on Software Utility - ScandAll 21.

17. The ScandAll 21 installation wizard will appear. Click next and follow the prompts to
complete the installation.

18. Once all of the above is completed then remove the Scanner Setup CD, Reboot
your system, and go to Step E.

Step D: Installing the drivers from our Web Page.

Installing the STI-Twain driver.

1. Create a new folder and name it Fujitsu Downloads.

2. Next go to the following link

3. Fill in the pre-registration box when it pops up and continue to the drivers download
page.

4. Afterwards click on STI Twain Software Drivers.

5. Scroll down the list of scanner models in the left column and select the appropriate
STI Twain driver to the right of your scanner model.

6. Double click on the driver file name and the File Download box will popup.

7. Click on Save and then use the browse (or other folder navigation) button until you
have the Twain Download folder you created in the Save As box.

8. Click Save.

9. When completed close the Download Complete window and go to the Twain
Download folder.

10. Open the folder and you will see the saved driver file. Double click on the file to
unzip it and the WinZip* self-extractor box will popup. Click on browse and select the
Fujitsu Downloads folder, then click on Extract. The file will begin to unzip and
when finished a message box will report the number of files unzipped. Click on OK
and close WinZip.

11. In the STI Twain Download folder locate the setup.exe file and double click.
Afterwards follow the prompts and reboot when finished

Installing the ASPI-Twain driver.

Some of our scanners are not supported by the STI-Twain drivers. For those units you
must install the ASPI-Twain driver. Please refer to the driver download page to see if
your model is one of them.

1. Create a new folder and name it Fujitsu Downloads.

2. Next go to the following link and click on

3. Fill in the pre-registration box when it pops up and continue to the drivers download
page.

4. Afterwards click on ASPI Twain Software Drivers.

5. Scroll down the list of scanner models in the left column and select the appropriate
ASPI Twain driver to the right of your scanner model.

6. Double click on the driver file name and the File Download box will popup.

7. Click on Save and then use the browse (or other folder navigation) button until you
have the Twain Download folder you created in the Save As box.

8. Click Save.

9. When completed close the Download Complete window and go to the Twain
Download folder.

Rev051906A Page 3 of 7

Drivers and Downloads.

Drivers and Downloads.