Page 1
Fujitsu Semiconductor Europe
User Manual
FSEUGCC-UM_SK-86R12-CPU01_Rev1.1
EMERALD-P
CPU MODULE
SK-86R12-CPU01
USERGUIDE
Page 2
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 2 - © Fujitsu Semiconductor Europe GmbH
Revision History
Date
Issue
30 Nov 2011
V1.0 Herbert Hönig
First release
07 Dec 2011
V1.01 Herbert Hoenig
Corrected typo
12 Jan 2012
V1.1 Herbert Hönig
Added PSMODE information
This document contains 11 pages.
Page 3
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 3 - © Fujitsu Semiconductor Europe GmbH
Warranty and Disclaimer
To the maximum extent permitted by applicable law, Fujitsu Semiconductor Europe GmbH restricts its
warranties and its liability for all products delivered free of charge (eg. software include or header
files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its
performance and any consequential damages, on the use of the Product in accordance with (i) the
terms of the License Agreement and the Sale and Purchase Agreement under which agreements the
Product has been delivered, (ii) the technical descriptions and (iii) all accompanying written materials.
In addition, to the maximum extent permitted by applicable law, Fujitsu Semiconductor Europe GmbH
disclaims all warranties and liabilities for the performance of the Product and any consequential
damages in cases of unauthorised decompiling and/or reverse engineering and/or disassembling.
Note, all these products are intended and must only be used in an evaluation laboratory
environment.
1. Fujitsu Semiconductor Europe GmbH warrants that the Product will perform substantially in
accordance with the accompanying written materials for a period of 90 days form the date of
receipt by the customer. Concerning the hardware components of the Product, Fujitsu
Semiconductor Europe GmbH warrants that the Product will be free from defects in material
and workmanship under use and service as specified in the accompanying written materials
for a duration of 1 year from the date of receipt by the customer.
2. Should a Product turn out to be defect, Fujitsu Semiconductor Europe GmbH´s entire liability
and the customer´s exclusive remedy shall be, at Fujitsu Semiconductor Europe GmbH´s sole
discretion, either return of the purchase price and the license fee, or replacement of the
Product or parts thereof, if the Product is returned to Fujitsu Semiconductor Europe GmbH in
original packing and without further defects resulting from the customer´s use or the transport.
However, this warranty is excluded if the defect has resulted from an accident not attributable
to Fujitsu Semiconductor Europe GmbH, or abuse or misapplication attributable to the
customer or any other third party not relating to Fujitsu Semiconductor Europe GmbH.
3. To the maximum extent permitted by applicable law Fujitsu Semiconductor Europe GmbH
disclaims all other warranties, whether expressed or implied, in particular, but not limited to,
warranties of merchantability and fitness for a particular purpose for which the Product is not
designated.
4. To the maximum extent permitted by applicable law, Fujitsu Semiconductor Europe GmbH´s
and its suppliers´ liability is restricted to intention and gross negligence.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES
To the maximum extent permitted by applicable law, in no event shall Fujitsu
Semiconductor Europe GmbH and its suppliers be liable for any damages whatsoever
(including but without limitation, consequential and/or indirect damages for personal
injury, assets of substantial value, loss of profits, interruption of business operation,
loss of information, or any other monetary or pecuniary loss) arising from the use of
the Product.
Should one of the above stipulations be or become invalid and/or unenforceable, the remaining
stipulations shall stay in full effect
Page 4
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 4 - © Fujitsu Semiconductor Europe GmbH
Contents
Revision History ........................................................................................................................ 2
Warranty and Disclaimer.......................................................................................................... 3
Contents ..................................................................................................................................... 4
0 Introduction / Features...................................................................................................... 5
1 System Overview ................................................................................................................ 6
2 Startup CPU Module ......................................................................................................... 7
3 Detailed Settings ................................................................................................................ 8
3.1 NAND / NOR Boot Option ................................................................................................... 8
3.2 DIP Switches .......................................................................................................................... 8
3.3 Power presets ....................................................................................................................... 10
3.4 USB HOST ........................................................................................................................... 10
3.5 LEDs ..................................................................................................................................... 10
4 Appendix .......................................................................................................................... 11
4.1 Used literature ..................................................................................................................... 11
4.2 Figures .................................................................................................................................. 11
Page 5
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 5 - © Fujitsu Semiconductor Europe GmbH
0 Introduction / Features
Here you will find a short summary and overview of the features that the SK-86R12-CPU01
Module offers.
It provides
3x APIX2 Video Outputs, 1x APIX2 Video Input
1x USB Host
JTAG/Trace Debug Connectors (20 Pin + Mictor Connector)
NOR Flash 1GBit
DDR3 2x 2GBit (= 512MByte)
NOR Flash usage with 16 oder 32 Bit access
Base Connectors for use with Emerald European Base Board SK-86R11-BASE and
Japanese Baseboard MB86R11EVB-BASE01
Mechanical dimensions:
- PCB : 117 x 127 mm
For details about interfaces refer to the Emerald-P Hardware Manual (see appendix).
Page 6
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 6 - © Fujitsu Semiconductor Europe GmbH
1 System Overview
The Emerald-P system consists of three modules:
CPU module (Emerald-P chip, USB connector): SK-86R12-CPU01
Base board (supplies interfaces and power): SK-86R11-BASE
Additional Addon board (from Jade-L system), provides 2x DVI output and 2x CVBS
input : SK-86R03-VIDEO
Figure 1-1: System Overview
Page 7
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 7 - © Fujitsu Semiconductor Europe GmbH
2 Startup CPU Module
- Connect the CPU Module to the baseboard
- Connect appropriate cables (HDMI, RS232, Power etc) to baseboard
(Please refer here to the Baseboard Manual – see appendix)
- Set switches SW1, SW11 and SW12 according to your needs (please refer here to
the Hardware Manual – see appendix)
- Power on baseboard
- Demo starts up on HDMI output
Default settings for the CPU Module :
- Clock PLL set to 533MHZ
- NOR Flash boot activated
- Bootloader and Linux system flashed in NOR and NAND Flash
Figure 2-1: Board Layout
Page 8
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 8 - © Fujitsu Semiconductor Europe GmbH
3 Detailed Settings
3.1 NAND / NOR Boot Option
For NAND/NOR Boot Option SW1 is used
NAND SELFL = HIGH Boot from NAND
NOR SEFLL = LOW Boot from onboard NOR (default)
3.2 DIP Switches
SW11 – PLL Mode
SW11
Signal
Description
Default
1
CRIPM0
ON = 0, OFF = 1
ON 2 CRIPM1
ON = 0, OFF = 1
ON 3 CRIPM2
ON = 0, OFF = 1
ON 4 CRIPM3
ON = 0, OFF = 1
ON
5
PLLBYPASS
ON = PLL Clock is bypassed
OFF = PLL Clock is not bypassed
OFF 6 PSMODE
OFF = PLL clock frequency divider ratio = 0
ON = PLL clock frequency divider ratio = 1
OFF 7 VINITHI
ON = Exception Vectors located at 0xFFFF0000
OFF = Exception Vectors located at 0x00000000
OFF
8 - Unused
OFF
Notes:
CRIPM[0:3] default settings results in 533 MHz clock frequency
Page 9
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 9 - © Fujitsu Semiconductor Europe GmbH
SW12 – MPX Mode
SW12
Signal
Description
Default
1
MPXMODE0
ON = 1, OFF = 0
OFF 2 MPXMODE1
ON = 1, OFF = 0
OFF 3 MPXMODE2
ON = 1, OFF = 0
OFF
4
NOREAN
NOR Flash Bus Width Select
ON = 32 Bit = 0 (Default)
OFF = 16 Bit = 1
ON
5
JTAGSEL
JTAG Select
ON = DFT
OFF = Normal (Default)
OFF
6
TESTMODE
Test Mode Select
ON= Test Mode
OFF = Normal (Default)
OFF
7
TRACEEN0
Pin Group B ETM
ON = use
OFF = not in use (Default)
OFF
8
TRACEEN1
Pin Group H ETM
ON = use
OFF = not in use (Default)
OFF
Notes:
MPX Mode Settings also available on Main Connector A
Attention: Do not set SW12-7 and SW12-8 to ON at the same time!
Page 10
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 10 - © Fujitsu Semiconductor Europe GmbH
3.3 Power presets
R24 1.2V APIX Power Supply Adjustment Set to 1.2V at Test Point TP8
R269 1.2V Power Supply Adjustment Set to 1.2V at Test Point TP4
R275 1.5V Power Supply Adjustment Set to 1.5V at Test Point TP13
3.3V APIX Power Supply : Dedicated LDO: R19 = OPEN, R20 = 0R
1.2V APIX Power Supply: Dedicated LDO: R21 = DNI, R22 = 0R
3.4 USB HOST
Settings:
Chip Select : used MEM_nCS2 -> R205 = 0R, R204 = OPEN
Interrupt : IRQ = INT_A0 -> R206 = 0R, R209 = OPEN
3.5 LEDs
D8 Global 5V Supply from base board connector
D9 1.2V supply to MB86R12 (APIX)
D10 3.3V supply to MB86R12 (APIX)
D12 1.2V supply to MB86R12 (general)
D13 5V Supply to USB bus
D14 Global 3.3V Supply from base board connector
D15 3.3V supply to MB86R12 (general)
D16 1.5V supply to DDR3 memory
D15 3.3V supply to MB86R12 (general)
Page 11
Emerald-P CPU Module
SK-86R12-CPU01
FSEUGCC-UM_MB86R12-CPU01_Rev1.1 - 11 - © Fujitsu Semiconductor Europe GmbH
4 Appendix
4.1 Used literature
Emerald-P Hardware Manual:
http://www.fujitsu.com/emea/services/microelectronics/gdc/gdcdevices/mb86r12emerald-p.html
Emerald-P CPU Module Schematics:
http://www.fujitsu.com/emea/services/microelectronics/gdc/evalbds/emerald-pstarterkit.html
Emerald-L Base Board Schematics:
http://www.fujitsu.com/emea/services/microelectronics/gdc/evalbds/emerald-pstarterkit.html
Software Update: Please check Website regularly for updates of the used Linux
system
http://www.fujitsu.com/emea/services/microelectronics/gdc/swtools/gdc-softwareindex.html
4.2 Figures
Figure 1-1: System Overview ................................................................................................................................. 6
Figure 2-1: Board Layout ................................................................................................................................ ....... 7
Loading...