Fujitsu SCALEOVIEW C17-7 User Manual

Downloaded from ManualMonitor.com Manuals

Note on mounting a swivel arm or a wall bracket

For instructions on how to mount the swivel arm or wall bracket, please see the
documentation for the swivel arm or wall bracket.

Only operating the monitor in the standard position (4:3, wide format, landscape mode) is
allowed.

Remarque concernant le montage du bras pivotant ou du support mural

Pour les instructions concernant le montage du bras pivotant ou du suppport mural,
veuillez vous reporter à la documentation du bras pivotant ou du support mural.

Lorsque le moniteur est en position standard (4:3, format large, mode paysage) est permis.

Hinweis zur Montage eines Schwenkarms oder einer Wandhalterung

Wie Sie Schwenkarm bzw. Wandhalterung montieren, entnehmen Sie bitte der
Dokumentation des Schwenkarmes bzw. der Wandhalterung.

Es ist nur erlaubt den Bildschirm in der Standardposition zu betreiben (4:3, Breitformat,
Landscape-Modus).

Nota sobre el montaje de un brazo basculante o un soporte de pared

Para las instrucciones sobre cómo montar el brazo basculante o el soporte de pared,
consulte la documentación correspondiente.

El monitor sólo se puede utilizar en la posición estándar (4:3, formato ancho, modo paisaje).

Nota sul montaggio dei bracci mobili o delle staffe a parete

Per istruzioni su come montare un braccio mobile o le staffe a parete si faccia riferimento
alla relativa documentazione.
È consentito l’uso del monitor solo nella posizione normale (4:3, formato wide, modalità
paesaggio).

Downloaded from ManualMonitor.com Manuals

Analog LCD Monitor

SCALEOVIEW C17-7 User’s Manual

Downloaded from ManualMonitor.com Manuals

Safety notes.............................................................................................i

Power cable............................................................................................ii

Transport.................................................................................................ii

CE marking.............................................................................................ii

FCC compliance statement......................................................................1

DOC compliance notice..........................................................................1

Introduction.............................................................................................2

Features..................................................................................................2

Unpacking...............................................................................................3

Attaching/Removing the base..................................................................4

Screen position adjustment.......................................................................4

Connecting the power cord......................................................................5

Safety precaution....................................................................................5

Cleaning your monitor..............................................................................5

Preset modes..........................................................................................6

Power saving..........................................................................................7

DDC.......................................................................................................7

Installation...............................................................................................8

User controls...........................................................................................9

Front panel controls..............................................................................9

Basic section of a OSD screen..........................................................10

Standard OSD operation....................................................................11

OSD function description...................................................................11

Troubleshooting.....................................................................................13

Specification..........................................................................................14

TABLE OF CONTENTS

Downloaded from ManualMonitor.com Manuals

Safety notes

This device complies with the relevant safety regulations for data processing equipment,
including electronic office machines for use in an office environment. If you have any
questions, contact your sales outlet or our help desk.

• The display surface of the LCD monitor is sensitive to pressure and scratches. You should

therefore be careful with the display surface so as to avoid lasting damage (Newton rings,
scratches).

• If the device is brought into the installation site from a cold environment, condensation can

form. Before operating the device, wait until it is absolutely dry and has reached
approximately the same temperature as the installation site.

• To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must

never be blocked.

• The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V.

Ensure that the local mains voltage lies within these limits.

• Ensure that the power socket on the device or the grounded mains outlet is freely

accessible.

• The ON/OFF switch does not disconnect the device from the mains voltage. To completely

disconnect the mains voltage, remove the power plug from the socket.

• The monitor is equipped with a power cable that complies with safety standards.

• No data transfer cables should be connected or disconnected during a thunderstorm.

• Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the

device (danger of electric shock, short circuit).

• The device is not waterproof! Never immerse the device in water and protect it from spray

water (rain, sea water).

• In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign

matter), switch off the unit, disconnect the power plug and contact your sales outlet or our
help desk.

• The monitor must be disposed of in accordance with the local regulations for disposal of

special waste. The screen background lighting contains mercury. You must observe the
applicable handling and disposal safety regulations for fluorescent tubes.

• Only qualified technicians should repair the device. Unauthorised opening and incorrect

repair may greatly endanger the user (electric shock, fire risk).

• Use a screen saver with moving images and activate the power management for your

monitor to prevent still images from “burning in”.

• Store this manual close to the device. If you pass the device on to third parties, you should

pass this manual on with it.

i User’s Guide

Downloaded from ManualMonitor.com Manuals

Power cable

To guarantee safe operation, use the cable supplied. Use the following guidelines if it is
necessary
to replace the original cable set.

• The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.

• The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on

the outer sheath.

• For devices which are mounted on a desk or table, type SVT or SJT cable sets may be

used.
For devices which sit on the floor, only SJT type cable sets may be used.

• The cable set must be selected according to the rated current for your device.

• If necessary, replace the original power cable with a regular grounded 3-core mains lead.

Transport

• Transport the monitor with care and only in its original packaging or another corresponding

packaging fit to protect it against knocks and jolts.

• Never drop the LCD monitor (danger of glass breakage).

CE marking

The shipped version of this device complies with the requirements of the

EECdirectives 89/336/EEC Electromagnetic compatibility” and 73/23/EEC Low
voltagedirective”.

SCALEOVIEW C17-7 ii

Downloaded from ManualMonitor.com Manuals

SCALEOVIEW C17-7 E-1

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide resonable
protection against radio frequency interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause interference to radio communications.
However, there is no guarantee that intereference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception (this can be
determined by turning this equipment off and on), the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between this equipment and the receiver.

• Connect this equipment to an outlet on a circuit different from which the

receiver is connected to.

• Consult the dealer or an experienced radio/TV technician for help.

Caution:

To comply with the limits for an FCC Class B computing device, always use the shielded
signal cable supplied with this unit.

Caution to the user:

The Federal Communications Commission warns the user that changes or modifications to
the unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

Notice of Compliance Canadian

Interference-causing Equipment Regulations

DOC Compliance Notice:

This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.

DOC Avis de Conformation

Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites
applicable aux appareils numériques de la class B prescrites dan le Réglement sur le brouillage
radioélectriques édicté par le ministére des Communications du Canada.

Downloaded from ManualMonitor.com Manuals