Fujitsu N6420 User Manual

Fujitsu LifeBook

N6420 Notebook

User’s Guide

Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. The absence of a product or service name, slogan, or logo does not constitute a waiver of any trademark or other intellectual property rights relating to that name, slogan, or logo owned by Fujitsu Computer Systems Corporation, its parent, subsidiaries, and affiliated companies.

Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.

Intel is a registered trademark and Core is a trademark of Intel Corporation or its subsidiaries in the United States and other countries.

The ExpressCard word mark and logo are owned by the Personal Computer Memory Card International Association (PCMCIA) and any use of such marks by Fujitsu Computer Systems Corporation is under license.

Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

PCMCIA is a trademark of the Personal Computer Memory Card International Association.

Memory Stick and Memory Stick Duo are trademarks of Sony, its parent, and/or its affiliates.

Adobe, Acrobat, and Acrobat Reader are either registered trademarks or trademarks of Adobe Systems, Incorporated in the United States and/or other countries.

Dolby Headphone manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.

Quicken is a registered trademark and/or registered service mark of Intuit, Inc. or one of its subsidiaries in the United States and other countries.

OmniPass is a trademark of Softex, Inc.

Roxio is a trademark of Roxio, a division of Sonic Solutions.

Norton, Norton AntiVirus, and Norton AntiSpam are registered trademarks of Symantec Corporation in the United States and other countries.

PowerProducer, MakeDisc, PowerDVD, and PowerDirector are trademarks of CyberLink Corp.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

All other trademarks mentioned herein are the property of their respective owners.

Warn ing

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

© Copyright 2007 Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, translated, stored, or transmitted in any electronic form without the written consent of Fujitsu Computer Systems Corporation.

B5FJ-2811-01EN-00

DECLARATION OF CONFORMITY

according to FCC Part 15

Responsible Party Name: Fujitsu Computer Systems Corporation

Address: 1250 E. Arques Avenue (M/S 122)

Sunnyvale, CA 94085

Telephone: (408) 746-6000

Declares that product: Model Configuration: LifeBook N6420

Complies with Part 15 of the FCC Rules.

This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This

device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.

LifeBook N6400 Series User’s Guide

IMPORTANT SAFETY INSTRUCTIONS

This product requires an AC adapter to operate. Use only a UL Listed I.T.E. AC Adapter with an output rating of 19V DC, with a current of 7.90A.

AC adapter output polarity:

When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

■

Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

■

Avoid using the modem during an electrical storm. There may be a remote risk of electric shock from lightning.

■

Do not use the modem to report a gas leak in the vicinity of the leak.

■

Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

■

To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord.

■

For TV tuner use: To protect from overvoltages and transients on the Cable Distribution System, make sure that the outer shield of the coaxial cable is connected to earth (grounded) at the building premise as close to the point of cable entrance as practicable, as required per NEC Article 820.93, ANSI/NFPA 70:

2005. If you have questions about your CATV installation, contact your service provider.

SAVE THESE INSTRUCTIONS

For Authorized Repair Technicians Only

Danger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instruction.

For continued protection against risk of fire, replace only with the same type and rating fuse.

System Disposal

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST

BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL LAWS.

Table of Contents

Fujitsu LifeBook® N6400 Series

Table of Contents

Volume Control

Controlling the Volume . . . . . . . . . . . . . . . . . . .18

PREFACE

Preface

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . .3

Fujitsu Contact Information . . . . . . . . . . . . . . . . .3

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

GETTING TO KNOW YOUR LIFEBOOK NOTEBOOK

Overview

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Locating the Controls and Connectors

Top and Front Components . . . . . . . . . . . . . . . . .8

Left-Side Panel Components . . . . . . . . . . . . . . .10

Right-Side Panel Components . . . . . . . . . . . . . . 11

Rear Panel Components . . . . . . . . . . . . . . . . . . .12

Bottom Components . . . . . . . . . . . . . . . . . . . . .14

Status Indicator Panel

Battery Charging Indicator . . . . . . . . . . . . . . . . .15

Battery Status Indicator . . . . . . . . . . . . . . . . . . .15

Hard Drive/Optical Drive Access Indicator . . . . .15

Email Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .15

NumLock Indicator. . . . . . . . . . . . . . . . . . . . . . .15

CapsLock Indicator. . . . . . . . . . . . . . . . . . . . . . .15

ScrLock Indicator . . . . . . . . . . . . . . . . . . . . . . . .15

Keyboard

Using the Keyboard . . . . . . . . . . . . . . . . . . . . . .16

Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . .16

Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .16

Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . .17

Touchpad Pointing Device

Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . .19

Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Touchpad Control Adjustment . . . . . . . . . . . . . .20

Application/Media Player Panel

Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Application Launch/Media Player Buttons . . . . .21

Configuring your Application Panel . . . . . . . . . .21

Using the Media Player Buttons . . . . . . . . . . . . .23

Using the Visual Optimizer . . . . . . . . . . . . . . . . .23

Desktop Control Panel (Windows XP Models) . .23

GETTING STARTED

Power Sources

Connecting the AC Adapter . . . . . . . . . . . . . . . .27

Display Panel

Opening the Display Panel . . . . . . . . . . . . . . . . .28

Adjusting Display Panel Brightness . . . . . . . . . . .28

Closing the Display Panel . . . . . . . . . . . . . . . . . .28

Starting Your LifeBook Notebook

Power On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . .29

Hard Disk Drive Passwords . . . . . . . . . . . . . . . . .29

BIOS Setup Utility. . . . . . . . . . . . . . . . . . . . . . . .29

Booting the System . . . . . . . . . . . . . . . . . . . . . .30

Starting Windows Vista the first time . . . . . . . . . 30

Starting Windows XP the First Time . . . . . . . . . . 31

Registering Your LifeBook notebook. . . . . . . . . . 31

Installing Click Me! . . . . . . . . . . . . . . . . . . . . . .31

Fujitsu Driver Update Utility . . . . . . . . . . . . . . .31

LifeBook N6400 Series User’s Guide

Power Management

Power and Suspend/Resume Button . . . . . . . . . 32

Suspend Mode. . . . . . . . . . . . . . . . . . . . . . . . . . 32

Hibernation (Save-to-Disk) Feature . . . . . . . . . . 33

Windows Power Management . . . . . . . . . . . . . . 33

Restarting the System. . . . . . . . . . . . . . . . . . . . . 33

Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

USER-INSTALLABLE FEATURES

Memory Stick/SD/xD Card Slot

Inserting Memory Stick/SD/xD Cards. . . . . . . . . 37

Removing Memory Stick/SD/xD Cards . . . . . . .38

Lithium ion Battery

Recharging the Batteries. . . . . . . . . . . . . . . . . . . 39

Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 40

Optical Drive

Optical Drive Software. . . . . . . . . . . . . . . . . . . . 41

Loading Media. . . . . . . . . . . . . . . . . . . . . . . . . . 41

Removing Media . . . . . . . . . . . . . . . . . . . . . . . .41

Emergency Optical Drive Tray Release . . . . . . . . 42

Playing Media on the Optical Drive . . . . . . . . . . 42

Using the Optical Player Software . . . . . . . . . . . 42

Using Dolby™ Headphone. . . . . . . . . . . . . . . . . 43

Using the Drive on Battery Power . . . . . . . . . . . 43

Auto Insert Notification Function . . . . . . . . . . . .44

Device Ports

Communications Ports . . . . . . . . . . . . . . . . . . . . 50

LAN Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

IEEE 1394 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Universal Serial Bus (USB) 2.0 Ports . . . . . . . . . . 50

S-Video Out Port. . . . . . . . . . . . . . . . . . . . . . . . 51

Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 51

Headphone/SPDIF Jack . . . . . . . . . . . . . . . . . . . 51

External Video Port . . . . . . . . . . . . . . . . . . . . . . 51

TROUBLESHOOTING

Troubleshooting

Identifying the Problem . . . . . . . . . . . . . . . . . . . 55

Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . 56

Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 56

Power On Self Test Messages . . . . . . . . . . . . . . 63

Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 64

Restoring Your Pre-installed Software

Restoring the Factory Image . . . . . . . . . . . . . . . 65

Automatically Downloading Driver Updates. . . . 66

CARE AND MAINTENANCE

Hard Disk Drive

Formatting the Hard Disk Drive . . . . . . . . . . . . . 45

PC Cards/ExpressCards™

Installing PC Cards . . . . . . . . . . . . . . . . . . . . . . . 46

Removing PC Cards . . . . . . . . . . . . . . . . . . . . . .46

Installing ExpressCards . . . . . . . . . . . . . . . . . . . . 47

Removing ExpressCards . . . . . . . . . . . . . . . . . . .47

Memory Upgrade Module

Installing a Memory Module . . . . . . . . . . . . . . .48

Removing a Memory Upgrade Module . . . . . . . 49

Checking the Memory Capacity . . . . . . . . . . . . . 49

Care and Maintenance

LifeBook Notebook . . . . . . . . . . . . . . . . . . . . . . 69

Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Floppy Disks and Drives . . . . . . . . . . . . . . . . . . . 70

DVDs and CDs. . . . . . . . . . . . . . . . . . . . . . . . . . 71

PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Table of Contents

Troubleshooting the WLAN

Troubleshooting Table . . . . . . . . . . . . . . . . . . . .97

SYSTEM SPECIFICATIONS

Specifications

Configuration Label . . . . . . . . . . . . . . . . . . . . . .75

Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . .75

Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Mass Storage Devices. . . . . . . . . . . . . . . . . . . . .75

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Environmental Requirements . . . . . . . . . . . . . . .76

Popular Accessories . . . . . . . . . . . . . . . . . . . . . .76

Pre-Installed Software . . . . . . . . . . . . . . . . . . . .77

Learning About Your Software . . . . . . . . . . . . . .77

GLOSSARY/REGULATORY

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Regulatory Information . . . . . . . . . . . . . . . . . . .85

Wireless LAN Glossary

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

IP address information

About IP Addresses . . . . . . . . . . . . . . . . . . . . .100

WLAN Specifications

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .101

APPENDIX B: USING THE FINGERPRINT SENSOR

Fingerprint Sensor Device

Introducing the Fingerprint Sensor Device . . . .105

Getting Started. . . . . . . . . . . . . . . . . . . . . . . . .105

Installing OmniPass . . . . . . . . . . . . . . . . . . . . .105

User Enrollment . . . . . . . . . . . . . . . . . . . . . . . .106

Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . .107

Configuring OmniPass . . . . . . . . . . . . . . . . . . .109

OmniPass Control Center. . . . . . . . . . . . . . . . .110

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .111

INDEX

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113

APPENDIX A: INTEGRATED WIRELESS LAN USER’S GUIDE

Before Using the Wireless LAN

Wireless LAN Modes Using this Device. . . . . . . .90

Wireless Network Considerations . . . . . . . . . . . .91

Deactivating the WLAN Device . . . . . . . . . . . . .91

Activating the WLAN Device . . . . . . . . . . . . . . .91

Configuration of the WLAN Device

Configuring the WLAN with Windows Vista. . . . 92

Configuration Using Intel PROSet Utility . . . . . . 92

Connection to the Network . . . . . . . . . . . . . . . .93

LifeBook N6400 Series User’s Guide

Preface

LifeBook N6400 Series User’s Guide

Preface

ABOUT THIS GUIDE

The LifeBook® N6400 notebook from Fujitsu Computer Systems Corporation provides desktop performance with a fast Intel® Core™ 2 Duo processor. The 17" Color Enhanced Crystal View WXGA+ high-resolution screen displays vibrant colors with pinpoint sharpness. The LifeBook features an ATI Mobility™ Radion® X1600 graphics chipset with 512 MB of HyperMemory™* or X1400 graphics chipset with 256 MB of HyperMemory*.

It comes with Microsoft® Windows Vista™ Home Premium, Windows Vista Business, or Windows XP Professional Edition pre-installed.

This manual explains how to operate your LifeBook notebook’s hardware and built-in system software.

Conventions Used in the Guide

Keyboard keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].

Pages with additional information about a specific topic are cross-referenced within the text. Example: (See page xx.)

On screen buttons or menu items appear in bold Example: Click OK to restart your LifeBook notebook.

The information icon highlights information that will enhance your understanding of the subject material.

The caution icon highlights information that is important to the safe operation of your computer or to the integrity of your files. Please read all caution information carefully.

The warning icon highlights information that can be hazardous to either you, your notebook, or your files. Please read all warning information carefully.

* HyperMemory™ is the cumulative total of dedicated and

system memory used by the Graphics Processing Unit (GPU) intended for use in the processing and creation of 3D and other images. The X1600 chipset with 512 MB of HyperMemory has 256 MB dedicated VRAM and 256 MB shared system memory; the X1400 chipset with 256 MB of HyperMemory has 128 MB dedicated VRAM and 128 MB shared system memory.

FUJITSU CONTACT INFORMATION

Service and Support

You can contact Fujitsu Service and Support the following ways:

■

Toll free: 1-800-8FUJITSU (1-800-838-5487)

■

E-mail: 8fujitsu@us.fujitsu.com

■

Website: http://www.computers.us.fujitsu.com/support

Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:

■

Product name

■

Product configuration number

■

Product serial number

■

Purchase date

■

Conditions under which the problem occurred

■

Any error messages that have occurred

■

Type of device connected, if any

Fujitsu Online

You can go directly to the online Fujitsu Product catalog for your LifeBook notebook by clicking on the Fujitsu Web links -> LifeBook Accessories Website URL link, located in the Windows Start menu.

You must have an active internet connection to use the on-line URL links.

You can also reach Fujitsu Service and Support online by clicking on the Fujitsu Service and Support Website URL link, located in the Fujitsu Web links -> Service and Support Software folder of the Windows Start menu.

To ensure that you always have the most current driver updates related to your system, you should occasionally access the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system.

The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one). If the FDU icon does not appear in the system tray, it can be started by going to [Start] -> All Programs, and clicking on Fujitsu Driver Update; this will create the icon automatically.

WARRANTY

Depending upon the configuration of your LifeBook notebook, your system is backed by either a one-year or three-year International Limited Warranty. Check the information that came with your LifeBook notebook for further warranty terms and conditions.

LifeBook N6400 Series User’s Guide

Getting to Know Your LifeBook Notebook

LifeBook N6400 Series User’s Guide

Getting to Know Your LifeBook

Figure 2-1. LifeBook N6400 Series

Overview

This section describes the components of your Fujitsu LifeBook N6400 Series notebook. We strongly recommend that you read it before using your LifeBook notebook, even if you are already familiar with notebook computers.

UNPACKING

When you receive your LifeBook notebook, unpack it carefully, and compare the parts you have received with the items listed below.

For a pre-configured model you should have:

■

LifeBook N6400 Series notebook computer

■

Lithium ion battery, pre-installed

■

AC adapter with AC power cord (Figure 2-2)

■

Phone/Modem (RJ-11) telephone cable

■

Drivers and Applications Restore CD

■

Recovery and Utility Disc

■

Getting Started Guide

■

User’s Guide (this guide)

■

International Limited Warranty Brochure

■

Microsoft-associated materials

Depending upon the configuration of your system, one or more of the following items may also be included in the box:

■

Application CDs for third-party software

■

Additional battery

■

Remote control package, including remote control, infrared remote control receiver, infrared control cable (available with Windows Vista™ Home Premium only)

■

ExpressCard Hybrid TV Tuner

Figure 2-2. AC Adapter

LifeBook N6400 Series User’s Guide

Locating the Controls and Connectors

Volume

4 5 6

Visual

Optimizer

Mode

Internet Mail

7 8

Figure 2-3. LifeBook notebook, display open 1

2 3 4 5

TOP AND FRONT COMPONENTS

The following is a brief description of your LifeBook notebook’s top and front components.

Display Panel Latch

The display panel latch locks and releases the display panel.

Display Panel

The display panel is a color LCD panel with back lighting for the display of text and graphics.

Display Panel Latch Display Panel Status Indicator Panel Visual Optimizer Button Application/Media Player Buttons Power/Suspend/Resume Button

Status Indicator Panel

The Status Indicator Panel displays symbols that correspond with a specific component of your LifeBook notebook. (See Status Indicator Panel on page 15 for more information)

Visual Optimizer Button

Enriches colors while in video mode and enhances text when viewing static web pages. (See Using the Visual

Optimizer on page 23 for more information)

Volume Control

Wireless LAN Switch

Stereo Speakers

Touchpad Pointing Device

Fingerprint

Recognition Sensor Keyboard

Getting to Know Your LifeBook

Application/Media Player Buttons

The LifeBook Application/Media Player buttons allow you to control the media player when your unit is on and to launch specified applications with the touch of a button. Note that if you are using the optional remote control, it overrides these buttons; the media buttons do not work while Media Center Edition is running. (See

LifeBook Application/Media Player Panel on page 21 for more information)

Power/Suspend/Resume Button

The Power/Suspend/Resume button allows you to suspend notebook activity without powering off, resume your notebook from suspend mode, and power on your LifeBook notebook when it has been shut down. (See Power On on page 29 for more information) and (See Power and Suspend/Resume Button on page 32

for more information)

Volume Control

The Volume Control toggle allows you to increase or decrease volume manually. (See Controlling the Volume

on page 18 for more information)

Wireless LAN Switch

The Wireless LAN On/Off Switch turns the wireless LAN on and off. (See Integrated Wireless LAN* User’s

Guide on page 87 for more information)

Stereo Speakers

The built-in boxless dual speakers provide stereo sound. Additionally, there is a subwoofer located on the bottom of the system. (See Bottom Components on page 14 for

more information)

Touchpad Pointing Device

The pointing device is a Touchpad that allows you simple cursor control. (See Touchpad Pointing Device on

page 19 for more information)

Fingerprint Recognition Sensor

The fingerprint recognition sensor allows you to increase the security of your system by having it "recognize" your unique fingerprint. (See Fingerprint Sensor Device on page 105 for more information)

The fingerprint recognition sensor can also be used as a scrolling button that lets you navigate quickly through a document without having to use the window scroll bars.

(See Scrolling on page 20 for more information)

Keyboard

A full-size keyboard with dedicated Windows keys and 10-key keypad. (See Using the Keyboard on page 16 for

more information)

LifeBook N6400 Series User’s Guide

Figure 2-4. LifeBook notebook left-side panel

LEFT-SIDE PANEL COMPONENTS

Following is a brief description of your LifeBook notebook’s left-side components.

Optical Drive

One of several different drives can be installed depending upon the configuration of your system. (See Optical Drive on page 41 for more information).

Optical Drive Eject Button

The optical drive eject button is used to eject the media tray.

DC Power Jack

The DC power jack allows you to plug in the AC adapter to power your LifeBook notebook and charge the internal Lithium ion battery.

Optical Drive

Optical Drive Eject Button

DC Power Jack

Figure 2-5. LifeBook notebook right-side panel 1

Getting to Know Your LifeBook

Memory Stick/SD/ xD Card Slot IEEE1394 Port

Headphone Jack

Microphone Jack

USB 2.0 Port

Subwoofer Speaker Air

Chamber ExpressCard Slot

PC Card Slot

PC Card Eject Button

ExpressCard Eject Button

RIGHT-SIDE PANEL COMPONENTS

Following is a brief description of your LifeBook notebook’s right-side components.

Memory Stick/SD/xD Card Slot

The Memory Stick/Secure Digital (SD)/xD card slot allows you to insert a flash memory card for data storage. This architecture allows you to transfer data between a variety of different digital devices. (See

Inserting Memory Stick/SD/xD Cards on page 37 for more information)

IEEE 1394 Port

The IEEE 1394 port is used to connect Firewire devices (such as digital cameras) to your LifeBook notebook.

(See IEEE 1394 Jack on page 50 for more information)

Headphone/SPDIF Jack

The headphone/SPDIF audio jack allows you to connect headphones or powered external speakers, or to download digital audio onto a MiniDisc recorder’s SPDIF (Sony Philips Digital Interface) format. (See Headphone/

SPDIF Jack on page 51 for more information)

Microphone Jack

The microphone jack allows you to connect an external stereo microphone. (See Microphone Jack on page 51 for

more information)

USB 2.0 Ports

The five USB ports (one on the right side panel and four on the rear panel) allow you to connect Universal Serial

Bus (USB) 2.0 or USB 1.1 devices. (See Universal Serial

Bus (USB) 2.0 Ports on page 50 for more information).

Windows Vista Users: All USB ports can be used to

connect an infrared remote control receiver that is required when using the optional Media Center Edition remote control. If you have Windows Vista installed, please change the setting of "Wake up by USB device" on "Windows Mobility Center from Disable to Enable.

ExpressCard Slot

The ExpressCard Slot allows you to insert an ExpressCard. (See PC Cards/ExpressCards™ on page 46 for more information)

PC Card Slot

The PC Card Slot allows you to insert a Type I or Type II PC Card. (See PC Cards/ExpressCards™ on page 46 for

more information)

PC Card Eject Button

The PC Card eject buttons are used to eject a PC Card from the PC Card slot. (See PC Cards/ExpressCards™ on

page 46 for more information)

ExpressCard Eject Button

The ExpressCard eject buttons are used to eject an ExpressCard from the ExpressCard slot. (See PC Cards/

ExpressCards™ on page 46 for more information)

LifeBook N6400 Series User’s Guide

Figure 2-6. LifeBook notebook back panel 1

LAN Port USB Ports

USB Port

Lock Slot

Modem Port

External Video Port

Air Vents

S-Video Out Port

REAR PANEL COMPONENTS

Following is a brief description of your LifeBook notebook’s rear panel components.

LAN Port

The LAN port is designed to accept a Local Area Network (LAN) RJ-45 jack. (See Communications Ports

on page 50 for more information)

USB 2.0 Ports

The five USB ports (one on the right side panel and four on the rear panel) allow you to connect Universal Serial Bus (USB) 2.0 or USB 1.1 devices. (See Universal Serial Bus (USB) 2.0 Ports on page 50 for more information). All USB ports can be used to connect an infrared remote control receiver that is required when using the optional Media Center Edition remote control. If you have Windows Vista installed, please change the setting of "Wake up by USB device" on "Windows Mobility Center" from Disable to Enable.

Anti-theft Lock Slot

The anti-theft lock slot allows you to attach an optional physical lock down device.

Modem Port

The modem port is designed to accept a Modem (RJ-11) telephone jack for the multi-national internal 56K modem. (See Communications Ports on page 50 for more

information)

The internal modem is not intended for use with Digital PBX systems. Do not connect the modem to a digital PBX as it may cause serious damage to the internal modem or your LifeBook notebook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem. Third-party hardware is available to allow modem-to-PBX interface.

The internal modem is designed to the ITUT V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum upload speed is 33600bps.

External Video Port

The external video port allows you to connect an external monitor or LCD projector. (See External Video

Port on page 51 for more information)

Air Flow Vents

The air flow vents assist in proper cooling of the system.

To protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used.

Do not operate the notebook in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.

S-Video Out Port

The S-Video out port is used to transmit a high resolution video signal to a compatible TV or VCR.

(See S-Video Out Port on page 51 for more information)

Getting to Know Your LifeBook

LifeBook N6400 Series User’s Guide

Figure 2-7. LifeBook notebook bottom panel 1

BOTTOM COMPONENTS

Following is a brief description of your LifeBook notebook’s bottom panel components.

Lithium ion Battery Bay

The battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery.

(See Lithium ion Battery on page 39 for more information)

Memory Compartment Cover

Your LifeBook notebook comes with high speed DDR2667 PC5300 SO-DIMM memory. The memory upgrade compartment allows you to expand the system memory capacity of your LifeBook notebook, thus improving overall performance. (See Memory Upgrade Module on

page 48 for more information)

Lithium ion Battery Bay Configuration Label (approximate location)

Memory Compartment Cover

Subwoofer

Air Flow Vents

Subwoofer

The subwoofer speaker provides bass-range sound to supplement the stereo speakers, resulting in high-quality audio.

Air Flow Vents

The air flow vents assist in proper cooling of the system.

Do not operate the notebook in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.

Getting to Know Your LifeBook

1 Battery Charging 2 Battery Status 3 Hard Drive/Optical Drive Access 4 Email Indicator 5 NumLock Indicator 6 CapsLock Indicator 7 ScrLock Indicator

Figure 2-8. Status Indicator Panel/Volume LEDs

Status Indicator Panel

The Status Indicator panel is located on the front of the palm rest, just below the latch point. Within this panel are symbols that correspond to specific components of your LifeBook notebook. These symbols tell you how each of those components is operating. (Figure 2-8)

BATTERY CHARGING INDICATOR

The Battery Charging indicator displays whether or not the Lithium ion battery is currently being charged.

LED Condition Charging Status of Battery

Green, solid Fully charged or no battery installed.

Orange, solid Being charged

Orange, blinking

Off

Charging suspended because battery temperature too high.

Not charging because AC adapter is not connected.

HARD DRIVE/OPTICAL DRIVE

ACCESS INDICATOR

The Hard Drive/Optical Drive Access indicator states whether your internal hard drive or optical drive are being accessed.

EMAIL INDICATOR

The Email indicator shows that you have received new email.

NUMLOCK INDICATOR

The NumLock indicator shows that the internal keyboard is set in ten-key numeric keypad mode.

CAPSLOCK INDICATOR

The CapsLock indicator shows that your keyboard is set to type in all capital letters.

BATTERY STATUS INDICATOR

This indicator shows how much charge is available within the installed battery.

LCD Condition Battery Charge Level

Green, solid Between 50% and 100% charged

Orange, solid Between 13% and 49% charged

Red, solid Between 0% and 12% charged

Red, blinking There is a problem with the battery

Off

No battery is installed or the system is shut off.

SCRLOCK INDICATOR

The ScrLock indicator shows that your scroll lock is active.

LifeBook N6400 Series User’s Guide

Figure 2-9. Keyboard 1

Keyboard

USING THE KEYBOARD

Your Fujitsu LifeBook notebook has an integrated 103key keyboard. The keys perform all the standard functions of a keyboard, including the Windows keys and other special function keys. This section describes the following keys.

■

Numeric keypad: Your LifeBook notebook has a tenkey numeric keypad which allows certain keys to serve dual purposes, both as numeric/mathematical keys and navigation keys. The ability to toggle between the numerical keys and navigation keys is controlled through the [NumLk] key.

■

Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents.

■

Function keys: The keys labeled [F1] through [F12] are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running.

■

Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.

564

Function Keys [Fn] Key

Start Key

Application Key

Cursor Keys

Numeric Keypad (surrounded by thick gray line)

NUMERIC KEYPAD

The right-hand section of the keyboard serves as a numeric keypad. To activate the keypad functions, press the [NumLk] button. Using the keypad keys, you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. When [NumLk] is not active, you can use the numeric keypad to navigate (Home, End, Page Up, Page Down, left, right, up, down). The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary functions.

WINDOWS KEYS

Your notebook has two Windows keys: a Start key and an Application key. The Start key displays the Start menu, and functions the same as your onscreen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Refer to your Windows documentation for more information regarding the Windows keys.)

CURSOR KEYS

The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right).

FUNCTION KEYS

Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used.

The [Fn] key provides extended functions for the notebook and is always used in conjunction with another key.

Icon Keys Description

Pressing [F3] while holding [Fn] will

[Fn+F3]

[Fn+F4]

[Fn+F6]

[Fn+F7]

[Fn+F8] Pressing [F8] repeatedly while

[Fn+F9] Pressing [F9] repeatedly while

toggle the Audio Mute on and off.

Pressing [F4] while holding [Fn] will toggle the touchpad on and off. (This function key combination only works if the BIOS setting for Advanced -> Keyboard/Mouse Features -> Internal Pointing Device is set to Manual Setting.)

Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.

Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.

holding [Fn] will lower the volume of your system.

holding [Fn] will increase the volume of your system.

Getting to Know Your LifeBook

[Fn+F10]

Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the key combination you will step to the next choice. The choices, in order, are: built-in display panel only, external device only, and both builtin display panel and external devices.

LifeBook N6400 Series User’s Guide

Volume Control

Your LifeBook notebook has multiple volume controls which interact with each other.

Any software that contains audio files will also contain a volume control of its own. If you install an external audio device that has an independent volume control, the hardware volume control and the software volume control will interact with each other. It should be noted that if you set your software volume to Off, you will override the external volume control setting.

CONTROLLING THE VOLUME

Methods to Control Volume

The volume can be controlled in several ways:

■

Volume can be set using the volume control toggle on the right of the WLAN switch.

Vol ume

Volume Control

Figure 2-10 Volume Control

■

Volume can be set from within the Volume Control in the Notification Area.

■

Volume can be controlled by many volume controls that are set within individual applications.

■

Certain external audio devices you might connect to your system may have hardware volume controls.

Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources.

We recommend that you experiment with the various volume controls to discover the optimal sound level.

Getting to Know Your LifeBook

Figure 2-11. Touchpad Pointing Device 12Cursor Control

Touchpad Pointing Device

The Touchpad pointing device is built into your notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left and right button, and an up-and-down scroll button (which also acts as a fingerprint recognition sensor).

The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger, and the more pressure you use, the faster the cursor will move.

The left and right buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending on the application that is being used. The up-and down scroll button allows you to quickly navigate up and down a screen. For information on using the scroll button as a fingerprint recognition sensor, refer to “Fingerprint Sensor Device” on page 105

An external mouse can be connected to the USB port on your notebook, and be used simultaneously with the Touchpad. However, if you boot the system with an external mouse connected the Touchpad will be disabled or enabled depending on your BIOS settings.

ity on page 29 for more information)

(See BIOS Setup Util-

Left Button

34Fingerprint Recognition

Sensor/Scroll Button Right Button

CLICKING

Clicking means pushing and releasing a button. To leftclick, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the Touchpad once. (Figure 2-12)

Figure 2-12. Clicking

DOUBLE-CLICKING

Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, then immediately release it. You also have the option to perform the double-click operation by tapping lightly on the Touchpad twice. (Figure 2-13)

Figure 2-13. Double-clicking

LifeBook N6400 Series User’s Guide

If the interval between clicks is too long, the double-click will not be executed. The interval length can be changed by going to Control Panel -> Mouse -> Mouse Properties -> Buttons tab.

DRAGGING

Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. (Figure 2-14)

Figure 2-14. Dragging

SCROLLING

Using the scrolling sensor allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navi-

gating through online pages. To use the scrolling sensor, move your finger forward or backward across the button to scroll up or down a page. When you have reached the desired section of the page, raise your finger.

Note that you can also scroll by sliding your finger up and down the right side of the touchpad. This feature is disabled by default, but you can enable it by going to Start -> Control Panel -> Mouse.

The scrolling sensor is also used as a fingerprint sensor.

(See Fingerprint Sensor Device on page 105 for more information)

Figure 2-15. Scrolling

TOUCHPAD CONTROL ADJUSTMENT

The Windows Control Panel allows you to customize your Touchpad with selections made from within the Mouse Properties dialog box.

LifeBook Application/Media Player

Figure 2-16. LifeBook Application/Media Player Panel Buttons

Mode Button

LifeBook Application/ Media Player Button

LifeBook Application/ Media Player Panel

A unique feature of your LifeBook notebook is the LifeBook Application/Media Player Panel. This feature makes your LifeBook notebook more than just another notebook computer. The panel allows you to operate the optical drive as an independent audio media player or to launch applications with the touch of one button.

■

The LifeBook Application Panel uses the date and time settings of your LifeBook notebook. If the date and time are incorrect, you can adjust the settings in the Windows Control Panel.

■

The media player that your LifeBook notebook uses is determined by the configuration of your system.

Your notebook is pre-installed with software utilities that let you operate and configure your LifeBook Application/Media Player Panel. These utilities are found under the Start menu -> Control Panel -> Application Panel. The panel consists of the following elements:

MODE BUTTON

Located at the left of the large LifeBook Application/ Media Player button ((Figure 2-16), this button allows you to select the function of the panel—either as an Application Launcher or a media player. When Application Launcher is selected, the mode indicator will light up.(Figure 2-17) When Media Player is selected, the media player indicators will light up. (Figure 2-18).

APPLICATION LAUNCH/ MEDIA PLAYER BUTTONS

The LifeBook Application/Media Player Button acts as a one-touch button that allows you to activate a number of functions and actions. If Application Launcher mode is selected, the labels on the outside of the button indicate which area of the button should be pressed to activate the application associated with the label. (Figure 2-

17). If Media Player mode is selected, the indicators within the button will light up (Figure 2-18).

Application A Label

Mode Indicator

Internet Mail

Internet Label

Application B Label

Figure 2-17 LifeBook Application Launch indicators

Play/Pause Button

Fast Backward Button

Stop/Eject Button

Figure 2-18 Media Player Buttons

EMail Label

Fast Forward Button

CONFIGURING YOUR APPLICATION PANEL

When you start your system, the LifeBook Application Panel is automatically activated. As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. To set up the panel to best suit your needs, we have provided the Application Panel Setup utility that quickly and easily helps you make the most of this valuable feature. Depending upon the operating system on your computer (Windows XP Pro or Windows Vista) the procedures differ slightly, as noted below.

LifeBook N6400 Series User’s Guide

Windows Vista Models:

To configure your LifeBook Application Panel with the Application Panel Setup utility:

1. Click on [Start] -> All Programs.

2. Select LifeBook Application Panel from the dropdown menu, then click on Setup of LifeBook Appli- cation Panel. The Button Setting window will open.

The Button Setting window has tabs that correspond to the buttons on the application panel. When you receive your notebook, these buttons are pre-configured to launch specific programs, as noted above.

In order to reconfigure a button to launch a different program, follow these steps:

1. On the Button Setting window, click the tab of the button you want to configure.

2. Ensure that the “Enable this button” check box is selected, then click the [Application registration...] button.

3. You can either select an application from the Start menu, or select an application directly by clicking the “Select from Start Menu” or “Select directly” button, respectively.

4. Once you’ve selected an application, click [Next].

5. In the next window, you can select to play a sound when the application starts.

6. Click [Finish] to complete the procedure. After this point, whenever you click the appropriate application button, the application to which you assigned it will start.

At the bottom of each application setup page are two selectable options. The first will enable/disable the button when your LifeBook notebook is in Standby mode, and the second will enable/disable the button when your LifeBook notebook is powered off. You can enable/disable either or both of these functions simply by clicking on the option.

When you have finished with Button Setting window, click on OK, and the new settings will take effect. You can reconfigure your LifeBook Application Panel as often as you like.

Windows XP Pro Models:

To configure your LifeBook Application Panel with Application Panel Setup:

1. Click on Start.

2. Click on Control Panel.

3. Double-click on Application Panel.

The Application Panel Setup utility will appear. There are tabs that correspond to the application buttons on the LifeBook Application Panel. When you receive your LifeBook notebook, these buttons are pre-configured to

launch specific programs. (See Specifications on page 69 for more information).

The tabs in Application Panel Setup may not be in the same order as the buttons on your LifeBook notebook. Please select the tab you wish to change carefully.

To change an application associated with one of the buttons, click on the tab for the button you would like to reconfigure. Click on the Browse button. Scroll down to the application you want to associate with the buttons, click on the application you wish to launch with this button, and then click Open. Click OK, and the button will now launch the new application.

One of the buttons may be preconfigured to launch your default Internet browser. In order to reconfigure it to launch a different program, follow these easy steps:

1. Click on the Internet tab of the application panel utility. Click on the down-arrow in the Specify the button action: field. Select Start Other Program from the dropdown list.

2. Click on the Browse button.

3. Scroll down the list of applications, and click on the application you wish to launch with this button. Click on Open.

4. Click OK.

The button will now launch the new application. If you want to return to launching your default Internet browser with this button, you need only click on “Default Internet Browser” from the dropdown list. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application” from this button, you will need to reconfigure it as described above.

The E-mail tab can be modified in the same manner as the Internet tab.

At the bottom of each application setup page are two selectable options. The first will enable/disable the button when your notebook is in Standby mode, and the second will enable/disable the button when your notebook is in the pseudo-off state. You can enable/disable either or both of these functions simply by clicking on the option.

If you choose to have the buttons work when the LifeBook notebook is in standby, they will function even if hit accidentally, and will turn on your LifeBook notebook even if you are not present or using your LifeBook notebook. This could deplete your battery, and you will need to recharge it before using the LifeBook notebook.

LifeBook Application/Media Player

When you have finished with Application Panel utility, click [OK]; the new settings will take effect. You can reconfigure your Application Panel as often as you like.

USING THE MEDIA PLAYER BUTTONS

The media player buttons are another way to use your LifeBook notebook’s optical drive as a media player.

• If you have Microsoft Windows Media Center Edition on your system, the media player buttons do not function, since the remote control device is used to operate the optical drive.

• If you shut down from Windows while the media player is playing a CD or DVD, it will stop.

• You can’t go into Hibernation Mode (Save-to-Disk) or Suspend Mode while the media player is playing.

• The media player will only play when the system is powered on.

There is no configuration required for media player operation. The buttons are pre-configured to work like a normal media player. The buttons will operate as follows:

Stop/Eject

Press this button once to stop a CD or DVD that is playing. Press it twice to eject the disc.

Play/Pause

Press this button to start playing a CD or DVD starting at the beginning. While the disc is playing, press it to pause. Press it again to continue

• If you press the play button and nothing happens, there is no disc in the media player drive, you have other than a media disc in the drive, or system is not powered on.

• Because of the Windows auto-insertion function, discs will start playing immediately after they are inserted if your LifeBook notebook is on. This will not happen if you are using the media player in Suspend mode.

Fast Backward

USING THE VISUAL OPTIMIZER

Visual Optimizer is a new feature which allows you to optimize your video viewing experience. The Visual Optimizer image quality enhancer delivers rich image quality by employing cutting-edge technologies such as a 3D color management system, auto contrast correction, black and white stretch, and edge enhancement.

The Visual Optimizer button is located adjacent to the Mode button. (See figure 2-3 on page 8 for location). The Visual Optimizer dynamically and automatically enhances images for optimal quality. To use the Visual Optimizer while viewing videos, press the button to activate it. To de-activate it, press the button again.

DESKTOP CONTROL PANEL (WINDOWS XP MODELS)

If you have Microsoft Windows XP Pro installed on your system, your notebook includes a desktop control panel for your notebook’s desktop that you can use at any time. You can use this panel to operate the media drive.

To use the desktop control panel:

1. Click on Start.

2. Click on All Programs.

3. Click on LifeBook Application Panel.

4. Click on CD Player.

The desktop control panel will appear in the corner of your screen.

To c lo s e t he pa ne l:

1. Click on the “x” button.

To minimize the panel:

2. Click on the “-” button.

You can select from four appearances for your desktop control panel. Double-click on the track display area of the panel, and a menu will appear which will allow you to select from a pull-down menu. On the same pop-up are three other options: “Always on top”, “Continuous Play”, and “Disable Stop/Eject Button CD Removal”. If you click “Always on top”, the desktop controls will always be seen on your screen, no matter what other application you are running. If you click “Continuous Play”, your media player will automatically start over at the beginning of the disc in the drive as soon as it finishes the last track. If you click “Disable Stop/Eject Button CD Removal”, the disc will not be ejected automatically when the Stop/Eject button is pressed.

Press this button once to skip one track back.

Fast Forward

Press this button once to skip forward one track.

You can move the desktop control panel to anywhere on the desktop. Drag it by clicking on the track number display, holding it down, and dragging the control panel. When you place it where you would like, release the mouse button

LifeBook N6400 Series User’s Guide

• If you have your display set to 256 colors, the basic display will appear no matter which one you select. You will need to set your display colors to more than 256 in order to select other display appearances.

• When you close the media player’s desktop control panel, it will stop the audio media player. Press the Play button if you would like to continue listening, and the media player will restart at track 1.

Disabling/Enabling the LifeBook Application Panel

To disable the Application Panel in a Windows XP environment, follow these easy steps:

Performing the following steps disables the LifeBook Application Panel buttons only when playing CD’s; DVD’s can still be run with the LifeBook Application Panel. Even when the buttons are disabled, discs can still be run using the Desktop Control Panel.

1. Click on Start.

2. Click on All Programs.

3. Click on LifeBook Application Panel.

4. Click on Stop Application Panel.

To reactivate, follow the same procedure, except for step

4. Click on Start Application Panel instead.

Every time you start Windows, the LifeBook Application Panel is activated, even if you deactivated it before you shut down.

Getting Started

LifeBook N6400 Series User’s Guide

Getting Started

Figure 3-1. Connecting the AC Adapter 12DC Power Jack

Power Sources

Your Fujitsu LifeBook notebook has two possible power sources: a Lithium ion battery or an AC adapter.

CONNECTING THE AC ADAPTER

The AC adapter provides power for operating your LifeBook notebook and is used to charge the batteries.

Connecting the AC Adapter

1. Plug the DC output cable into the DC power jack of your LifeBook notebook.

2. Plug the AC cable into the AC adapter.

3. Plug the AC cable into an AC electrical outlet.

(Figure 3-1)

DC Output Cable

34AC Adapter

AC Cable

Switching from AC Adapter Power to Battery Power

1. Be sure that you have a charged battery installed.

2. Unplug the AC adapter.

■

When you run the N6400 Series LifeBook on battery power, by default, the CPU will slow down approximately by half in order to optimize battery life. This feature can be enabled or disabled in the BIOS. Use an AC Adapter whenever possible.

■

The Lithium ion battery is not charged upon purchase. Initially, you will need to connect the AC adapter to use your LifeBook notebook.

LifeBook N6400 Series User’s Guide

Display Latch Button

Figure 3-2. Opening the Display Panel

Display Panel

Your Fujitsu LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of activematrix technology.

OPENING THE DISPLAY PANEL

1. Push the display latch button to release the locking mechanism.

2. Lift the display panel backwards, being careful not to touch the screen, until it is at a comfortable viewing angle.

ADJUSTING DISPLAY PANEL BRIGHTNESS

Once you have turned on your LifeBook notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. To adjust the display brightness, use the Function keys on the keyboard.

Using the Keyboard to Change Display Brightness

■

[Fn+F6]: Pressing this key combination repeatedly will lower the brightness of your display.

■

[Fn+F7]: Pressing this key combination repeatedly will increase the brightness of the display.

Display Cover

■

If using AC power, your LifeBook notebook’s brightness setting is set to its highest level by default. If using battery power, the brightness setting is set to its middle level by default.

■

The higher the brightness level, the more power the notebook will consume and the faster your batteries will discharge. For maximum battery life, set the brightness level as low as possible.

CLOSING THE DISPLAY PANEL

1. Holding the edge of your display panel, pull it forward until it is flush with the body of your LifeBook notebook.

2. Push down until you hear a click. This will engage the locking mechanism and prevent your display panel from opening unexpectedly.

Starting Your LifeBook Notebook

POWER ON

Power and Suspend/Resume Button

The Power and Suspend/Resume button is used to power on your LifeBook notebook, to resume from Standby or Save-to-Disk mode or to place your notebook in Standby or Save-to-Disk mode. (You can also use the button to power down the system by holding it down for approximately five seconds. This can be useful if the system is “hung up”. This shouldn’t be used as the normal means of shutdown, however.) You can also turn off your notebook by choosing Shut Down from the Windows Start menu.

Power/Suspend Resume Button

Figure 3-3. Powering Up the System

Once you have connected your AC adapter or charged the internal Lithium ion Battery, you can press this button to power up your notebook. (Figure 3-3)

When you turn on your notebook be sure you have a power source. This means that the battery is installed and charged, or the AC adapter is connected and has power.

Getting Started

Never turn off your notebook during the Power On Self Test (POST) or it will cause an error message to be displayed when you turn your notebook on the next time.

(See Power On Self Test Messages on page 63 for more information)

BOOT SEQUENCE

The procedure for starting-up your notebook is termed the Bootup sequence and involves your notebook’s BIOS. When your notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook. This information is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until the operating system is loaded. During booting, your notebook is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.

The boot sequence is executed when:

■

You turn on the power to your LifeBook notebook.

■

You restart your LifeBook notebook from the Windows Shut Down dialog box.

■

The software initiates a system restart. Example: When you install a new application.

HARD DISK DRIVE PASSWORDS

To provide additional security for your data, you can assign passwords to your hard disk drive(s). This feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about accessing the

utility

Do not carry the notebook around with power on or subject it to vibration or shocks; doing so could damage the notebook.

When you Power On your notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your notebook will emit an audio warning and/ or an error message will be displayed. (See Power On Self Test Messages on page 63 for more information). Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.

After satisfactory completion of the Power On Self Test (POST), your notebook will load your operating system

Remember your passwords. If you set and forget your User and Master hard disk passwords, Fujitsu Computer Systems will not be able to reset it. You may lose data and have to replace your system board or hard disk drive.

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your notebook.

The BIOS Setup Utility also allows you to configure such features as the System Data Security feature parameters,

such as passwords.

LifeBook N6400 Series User’s Guide

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following (or use the TrustedCore menu as described in the next section):

1. Turn on or restart your LifeBook notebook.

2. Press the [F2] key once the Fujitsu logo appears on the screen; this will open the main menu of the BIOS Setup Utility with current settings displayed.

3. Press the right or left arrow keys to scroll through the other setup menus to review or alter the current settings. Additional navigational information is located at the bottom of the BIOS screen.

Using the TrustedCore Menu

When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear.

The TrustedCore Menu provides shortcuts to the following menus and information screens:

■

BIOS Setup

■

Diagnostic Screen

■

Boot Menu

■

Patent Information

■

System Information

■

Continue Booting

Clicking on any of the fields will invoke the screen, information, or action described.

The Boot Menu can also be invoked by pressing the [F12] key when the Fujitsu logo appears on the screen.

BIOS Guide

A guide to your notebook’s BIOS is available online at our service and support Website at http:// www.computers.us.fujitsu.com/support. Once there, select Support, then Notebooks under User’s Guides. Select LifeBook BIOS Guides from the pull-down menu for your LifeBook series. If you are unsure of your notebook’s BIOS number, refer to your packing slip

If your data security settings require it, you may be asked for a password before the BIOS main menu will appear.

BOOTING THE SYSTEM

We strongly recommend that you not attach any external devices and do not put a DVD/CD in your drive until you have gone through the initial power on sequence.

When you turn on your LifeBook notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.

Depending upon your operating system (Windows Vista or XP edition), there is a different procedure for stating your system for the first time, as outlined below.

STARTING WINDOWS VISTA THE FIRST TIME

The first time you initialize your Windows Vista system, the screen will be blank for approximately two minutes. This is

normal. After initialization, a “Set Up Windows” dialog box will appear.

Important: During the setup procedure, do not disconnect the power supply, press any buttons, or use any peripheral devices such as a mouse, keyboard, or remote control.

In order to ensure that you receive the most benefits from the Windows Vista operating system, it should be registered the first time you use it.

1. First of all, you will need to read and accept the End User License Agreements (EULAs).

■

If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows or to shut down your LifeBook notebook.

■

You cannot use your notebook until you have accepted the License Agreement. If you stop the process your notebook will return to the beginning of the Windows Welcome Process, even if you shut your notebook down and start it up again.

2. You will be prompted to enter your User Name and Password and you will be given a chance to select an icon for your account.

3. The next screen asks for a Computer Name and allows you to choose a desktop background.

4. You will next see a "Help protect Windows automatically" screen in which the default choice is "Use recommended settings”. The other two choices are "Install important updates only" and "Ask me later". Select from the three choices.

5. On the next screen set your time and date settings.

6. You will next see the "Select your computer's current location" screen. Make your selection from Home, Work (Default), and Public location.

7. The "Thank you" screen follows and an offer for free Norton is extended. Following are several screens while Windows checks the system performance.

8. Windows will then boot up for the first time.

Getting Started

Registering Windows Vista with Microsoft

1. After Windows has booted up for the first time, the Control Panel Welcome Center will appear. If the Register Windows Online icon is not seen in the window, click on “Show all 14 items”.

2. Click on Register Windows Online and follow the instructions that appear to register your copy of Windows.

STARTING WINDOWS XP THE FIRST TIME

Registering Windows XP with Microsoft

In order to ensure that you receive the most benefits from the Windows operating system, it should be registered the first time you use it.

After you receive the Windows Welcome screen, you will be prompted to enter registration information in the following order.

First of all, you will need to read and accept the End User License Agreements (EULAs). After accepting the EULAs, you will be asked if you want to enable the Automatic Updates feature. Acceptance of this feature is recommended because it allows your system to be updated automatically whenever an important change becomes available for your notebook.

■

If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows or to shut down your LifeBook notebook.

■

You cannot use your LifeBook notebook until you have accepted the License Agreement. If you stop the process your notebook will return to the beginning of the Windows Welcome Process, even if you shut your notebook down and start it up again.

Several additional windows will appear, prompting you to enter a name and description for your computer, an Administrator password, and a domain name. Read the instructions on the screens carefully and fill in the information as directed.

You will then be automatically connected to the Internet, if you have an appropriate connection available. If an automatic connection is not possible, you will be asked about how you dial out from where you will be using your LifeBook notebook. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button.

Once you are connected to the Internet, you will be asked if you wish to continue with the registration. If you select Ye s you will then enter your name and

address, and email address if desired. Click Next to complete registration.

REGISTERING YOUR LIFEBOOK NOTEBOOK

How do I register my LifeBook notebook?

You can register your LifeBook by going to our website:

us.fujitsu.com/computers

You will need to be set up with an Internet Service Provider (ISP) to register online.

ClickMe!

INSTALLING CLICK ME!

Before installing the ClickMe! utility, be sure the wireless LAN switch is turned on.

Windows Vista Systems

The first time you boot up your system, you will see a “Primary Settings for the PC” window. This window explains the installations which will be performed by the Click Me! utility. If you click [Execute], Click Me! will begin installing. If after clicking the button you receive a “User Account Control” window, you will be asked for your permission to continue. Click [Yes] to continue. If you cancel the operation, the Click Me! icon will appear on your desktop for later installation.

Windows XP Systems

The first time you boot up your system, you will see an icon called Click Me! in the Start menu. We highly

recommend that you install the ClickMe! utility the first time you boot up. When you click the Click Me!

icon, your system will automatically build the icon tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access., such as wireless LAN software provided by the wireless LAN manufacturer.

There may be additional third-party applications that are not installed by the ClickMe! utility. For more information, refer to your Getting Started Guide.

FUJITSU DRIVER UPDATE UTILITY

Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 83.

LifeBook N6400 Series User’s Guide

Power Management

Your LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your LifeBook notebook may be controlled from settings made in your operating system.

Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly. For example, you can create an appropriate power saving profile, put your notebook into Suspend mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings.

POWER AND SUSPEND/RESUME BUTTON

When your LifeBook notebook is active, the Power and Suspend/Resume button can be used to manually put your notebook into Suspend mode. Push the Power and Suspend/Resume button when your notebook is active, but not actively accessing anything, and immediately release the button. You will hear two short beeps and your system will enter Suspend mode.

If your notebook is suspended, pushing the Power and Suspend/Resume button will return your notebook to active operation. You can tell whether or not your system is in Suspend mode by looking at the Power indicator which is part of the Suspend/Resume button. (See Figure 2-8 on page 15 for location) If the indicator is visible and not flashing, your LifeBook notebook is fully operational. If the indicator is both visible and flashing, your notebook is in Suspend mode. If the indicator is not visible at all, the power is off or your notebook is in Save-to-Disk (Hibernation) mode. (See Hibernation

(Save-to-Disk) Feature on page 33 for more information)

SUSPEND MODE

Suspend or Standby mode saves the contents of your LifeBook notebook’s system memory during periods of inactivity by maintaining power to critical parts. This mode will turn off the CPU, the display, the hard drive, and all of the other internal components except those necessary to maintain system memory and allow for restarting. Your LifeBook notebook can be put in Suspend mode by:

■

Pressing the Power/Suspend/Resume button when your system is turned on.

■

Selecting Standby from the Windows Shut Down menu.

■

Timing out from lack of activity.

■

Allowing the battery to reach the Dead Battery Warning condition.

Your LifeBook notebook’s system memory typically stores the file(s) on which you are working, open application(s) information, and any other data required to support the operation(s) in progress. When you resume operation from Suspend mode, your LifeBook notebook will return to the point where it left off. You must use the Power and Suspend/Resume button to resume operation, and there must be an adequate power source available, or your LifeBook notebook will not resum

■

If you are running your notebook on battery power, be aware that the battery continues to discharge while your notebook is in Suspend mode, though not as fast as when fully operational.

■

Disabling the Suspend/Resume button prevents it from being used to put your LifeBook notebook in Suspend or Saveto-Disk mode. The resume function of the button cannot be disabled.

■

The Suspend or Hibernation (Save-toDisk) mode should not be used with certain PC Cards. Check your PC Card documentation for more information.

■

When PC Cards or external devices are in use, Hibernation (Save-to-Disk) mode cannot return to the exact state prior to suspension because all of the peripheral devices will be re-initialized when the system re-starts.

■

If your notebook is actively accessing information when you enter the Suspend or Hibernation (Save-to-Disk) mode, changes to open files are not lost. The files are left open and memory is kept active during Suspend mode, or the memory is transferred to the internal hard drive during Hibernation mode.

■

The main advantage of using the Hibernation (Save-to-Disk) function is that power is not required to maintain your data. This is particularly important if you will be leaving your LifeBook notebook in a suspended state for a prolonged period of time. The drawback of using Hibernation mode is that it lengthens the power down and power up sequences and resets peripheral devices.

■

Your system is set to use the Max Battery power scheme when running on battery power. If you change the power scheme to a different profile, your battery life may vary.

Getting Started

HIBERNATION (SAVE-TO-DISK) FEATURE

The Hibernation feature saves the contents of your notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature.

Enable or Disable the Hibernation Feature

Windows Vista:

The default settings are not enabled. To enable or disable the Hibernation feature follow these steps:

1. From the Start menu, select Control Panel, then select Power Options.

2. Select “Choose what the power button does” or “Choose what closing the lid does”, then make your selections (Do Nothing, Sleep, Hibernate, or Shut Down).

Windows XP:

The default settings are not enabled. To enable or disable the Hibernation feature follow these steps:

1. From the Start menu, select Settings, and then select Control Panel.

2. From the Control Panel select Power Options.

3. Select the Hibernate tab. Select the box to enable or disable this feature.

WINDOWS POWER MANAGEMENT

The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Options to set the timeout values for turning off the display and hard disks whether you are running the notebook on battery power or one of the adapters.

RESTARTING THE SYSTEM

If your system is on and you need to restart it, be sure that you use the following procedure.

Windows Vista

1. Click the Start button, and then move the mouse over the right arrow.

2. Select the desired action from the list.

3. Click OK to restart your notebook. Your notebook

will shut down and then reboot.

Turning off your LifeBook notebook without exiting Windows or turning on your notebook within 10 seconds of the notebook being shut off may cause an error when you start the next time.

POWER OFF

Before turning off the power, check that the hard drive/ optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your notebook shuts down without error,

use the Windows shut down procedure.

Be sure to close all files, exit all applications, and shut down your operating system prior to turning off the power. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors.

Using the correct procedure to shut down from Windows allows your notebook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:

Windows Vista

1. Click the Start button, and then move the mouse over the right arrow.

2. Select the desired action from the list.

Windows XP

1. Click the Start button, and then click Shut Down.

2. Select the Shut Down option from within the Windows Shut Down dialog box.

3. Click OK to shut down your notebook.

If you are going to store your notebook for a month or more see Care and Maintenance Section.

Windows XP

1. Click the Start button, and then click Shut Down.

2. Select the Restart option from within the Windows Shut Down dialog box.

LifeBook N6400 Series User’s Guide

User-Installable Features

LifeBook N6400 Series User’s Guide

Memory Stick or Memory Stick PRO

Memory Stick/SD/xD Card Slot

Figure 4-1. Inserting a Memory Stick/SD/xD Card

Memory Stick/Secure Digital/xD Card Slot

Your LifeBook notebook supports the following memory cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.

■

SD Memory Card

■

Memory Stick Media

■

Memory Stick Select Media

■

Memory Stick Duo Media (Note: An adapter is required for Memory Stick Duo)

■

Memory Stick PRO Media

■

xD Picture Cards

• Some of the media in the above list may have more features than others.

• Copyright Protection Technology cannot be used.

• MultiMedia Cards (MMC) and Secure MMC are not supported.

Memory Stick is a flash memory technology developed by Sony Electronics. Memory Stick allows you to record, transfer and share digital content, such as digital pictures, movies, music, voice, and computer data and applications.

Secure Digital (SD) Cards are very similar to Memory Sticks, but they are shorter. Like the Memory Stick, SD Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. SD Cards transfer data quickly, with low battery consumption. Like the memory stick, it uses flash memory architecture.

User-Installable Features

Secure Digital (SD) Card

xD Picture Card

Figure 4-2. Memory Stick, Secure Digital, and xD Cards

INSERTING MEMORY STICK/SD/XD CARDS

Memory Sticks, SD Cards, and xD Cards are inserted in the Memory Stick/SD/xD Card slot (Figure 4-1). To insert a Memor y Stick, SD Card or xD Card, follow these steps:

■

Inserting or removing a Memory Stick, SD Card, or xD Card during your notebook’s shutdown or bootup process may damage the card and/or your notebook.

■

Do not insert a card into a slot if there is water or any other substance on the card as you may permanently damage the card, your notebook, or both.

1. See your Memory Stick, SD Card, or xD Card manual for instructions on the insertion of your card.

2. Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD/xD Card.

3. Insert the card in an adapter, if required.

4. Insert your card into the slot with the product label facing up.

5. Push the card firmly into the slot until it is seated in the connector.

LifeBook N6400 Series User’s Guide

REMOVING MEMORY STICK/SD/XD CARDS

To remove a Memory Stick, SD Card, or xD Card, follow these easy steps:

• When removing cards from your notebook, be sure to click the Safely Remove Hardware icon in the system tray and select the item you want to remove.

• See your card manual for specific instructions on the removal of your card. Some cards may require your LifeBook notebook to be in Suspend Mode or Off while removing them.

Push the Memory Stick, SD Card, or xD Card adapter in until it unlatches. It will then eject from the slot for removal.

User-Installable Features

Lithium ion Battery

Your Fujitsu LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The rechargeable battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards. For information on maximizing your battery life, refer to the section entitled “Power Management” on page 32.

The Lithium ion battery operating time may become shorter if it is used under the following conditions:

■

Your system is set to use the Max Battery power scheme when running on battery power. If you change the power scheme to a different profile, your battery life may vary.

■

When used at temperatures that exceed a low of 5°C (40°F) or a high of 35°C (95°F). Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range. (See Battery Charging Indicator on

page 15 for more information)

■

When using a high current device such as a modem, DVD/CD-RW drive, DVD writer, or hard drive, using the AC adapter will conserve your battery life.

■

Do not leave a faulty battery in your LifeBook notebook. It may damage your AC adapter or your notebook itself. It may also prevent operation of your notebook by draining all available current into the bad battery.

■

Under federal, state, or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this information elsewhere, contact your support representative at: 1-800-8FUJITSU (1-800-838-5487).

Actual battery life will vary based on factors such as screen brightness, applications, features, power management settings, battery condition and other customer preferences.

DVD- writer, or hard drive usage may

also have a significant impact on battery life. Battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it.

DVD/CD-RW,

RECHARGING THE BATTERIES

If you want to know the condition of the primary Lithium ion battery, check the Battery Status indicator located on the Status Indicator panel. The indicator changes as the battery level changes.

The Lithium ion battery is recharged internally using the AC adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LifeBook notebook and connect the AC adapter

Make sure the Battery Charging indicator and the percentage charge is shown inside the Battery Status icon on the Status Indicator Panel.

There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your LifeBook notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your LifeBook into Suspend mode, or turn it off while the adapter is charging the battery. (See Power Management on page 32 for more

information on Suspend mode and shutdown procedure)

Using high current devices such as a modem or frequent optical drive accesses may prevent complete charging.

Low Battery State

When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your LifeBook notebook will go into Suspend mode. There is no guarantee that your data will not be lost once the notebook reaches this point

Note that you can change the state in which the battery goes into Suspend mode in the Power properties of the Control Panel.

To prevent loss of data, you should save all your active data and put your notebook into Suspend mode when the low battery message appears, until you can provide a new power source. When you are in Suspend mode, there must always be at least one power source active. If you turn off the power with the power/suspend/ resume button, or remove all power sources while your notebook is in Suspend mode, any data that has not been saved to the hard drive will be lost. You should provide power to your notebook from an AC power adapter as soon as possible.

LifeBook N6400 Series User’s Guide

Dead Battery Suspend mode shows on the Status indicator just like the normal Suspend mode. Once your LifeBook notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power from an AC adapter. Once you have provided power, you will need to press the Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your LifeBook notebook while the adapter is charging the battery.

Shorted Batteries

The Status Indicator panel displays the battery status via the Battery Status indicator to show the charge level available in that battery. If the display is flashing red, it means that the battery is damaged and must be replaced so it does not damage any other parts of your LifeBook notebook.

REPLACING THE BATTERY

With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged.

Follow the steps below to replace a battery (Figure 4-3):

1. Have a charged battery ready to install.

2. Shut down your notebook and disconnect the AC adapter.

3. Turn the system over.

4. Press the two battery latches towards the battery pack.

5. Lift the battery and remove it from the bay.

Battery Latches

Battery Pack

Figure 4-3. Removing the Battery

6. Place a charged battery into the bay and press it down until the latches click into place. (Figure 4-4)

7. Plug in the AC adapter and turn the power on.

Figure 4-4. Installing the Battery

User-Installable Features

Figure 4-5. Optical Drive 12DVD/CD Holder Tray

Optical Drive

Your Fujitsu LifeBook notebook contains an optical drive which is either a Dual-Layer Multi-Format DVD Writer or a High-Definition (HD) DVD-ROM player.

OPTICAL DRIVE SOFTWARE

Dual-Layer Multi-Format DVD Writer model only: With this drive, you can play CDs and DVDs, record CD+/-Rs and CD+/-RWs, and record DVD+R DLs, DVD+/-R, DVD-RWs and DVD-RAMs.

HD DVD-ROM model only: With the HD DVD-ROM model, you can play HD DVD-ROM, DVD-ROM, DVD-RAM, DVD-R/+R, DVD-RW/+RW, CD-ROM, CD-R/RW, and dual-layer DVD-R/+R discs and write data onto recordable CD-R, CD-RW, DVD-R/+R, DVDRW/+RW, DVD-RAM, and dual-layer DVD-R/+R discs.

■

Prior to using your Optical Drive, you must install the Optical Player software. Refer to the applicable readme file

on the Driver Applications CD-ROM for instructions on installing your Optical Player software.

■

You should periodically check the Fujitsu Website at: us.fujitsu.com/computers for current updated drivers.

■

Prolonged use of the optical drive, such as watching a DVD movie, will substantially reduce your battery life.

Do not operate your optical drive unless your LifeBook notebook is sitting on a flat surface. Using a drive when the system is not level may damage the drive or prevent proper operation.

DVD/CD Eject Button

LOADING MEDIA

To load a disc into your optical drive, follow these steps:

1. Push and release the eject button on the front of the optical drive to open the holder tray. The tray will come out of the notebook a short distance.

2. Gently pull the tray out until a media disc can easily be placed in the tray.

There may be a protective sheet in the tray from when it was shipped; please make sure it is removed before operating the drive, otherwise your drive may be damaged.

3. Place the media into the tray, label side up, with the hole in the center of the disc. Snap the disc onto the raised circle in the center of the tray.

4. Gently push the holder tray back in until you hear a click. (Figure 4-6)

If you have disabled the Auto Insert Notification Function, you will have to start the drive from your desktop, since your notebook will not automatically recognize that media has been loaded.

REMOVING MEDIA

1. Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the notebook a short distance.

2. Gently pull the tray out until the disc can easily be removed from the tray.

3. Carefully remove the media disc from the holder tray.

4. Gently push the holder tray back in until you hear a click.

LifeBook N6400 Series User’s Guide

Figure 4-6. Loading Media

EMERGENCY OPTICAL DRIVE TRAY RELEASE

If for some reason the eject button fails, you can open the media tray with a paper clip inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole. The tray will pop out a short distance.

Figure 4-7. Emergency Removal of a CD/DVD

PLAYING MEDIA ON THE OPTICAL DRIVE

There are three ways to operate the optical drive:

■

Using the Optical Player Software

■

Using the Media Player Buttons

■

Using the Desktop Control Panel

■

Using Microsoft Windows XP Media Center Edition (for systems with Media Center Edition installed)

USING THE OPTICAL PLAYER SOFTWARE

■

Prior to using your optical drive, you must install the optical player software. For details on using your optical player software, refer to the software Help file.

■

High-definition (HD) DVDs cannot be played using the Microsoft Windows XP Media Center Edition controls. To play HD DVD-ROMs, use the CyberLink PowerDVD application.

■

If you have WIndows XP Media Center Edition installed, follow the on-screen instructions to operate the application.

■

If you are running Windows XP Media Center Edition, the remote control overrides the media player buttons; the media player buttons do not work while Media Center Edition is running.

Starting a DVD Movie

1. Insert the DVD into the notebook’s optical drive. If the CD AutoRun feature activates, skip Step 2.

2. The first time you insert a movie into the DVD/CDRW tray, you will be prompted to select what you want the system to do when discs are inserted (e.g., start automatically or wait for a prompt). Until you make a selection, you will receive the same prompt whenever you insert a disc.

3. Click OK to close the About DVD Player Performance dialog box and the movie will begin. After you make your selections, the PowerDVD control panel will appear whenever you insert a disc.

Opening the DVD/CD-RW Drive Control Panel

With most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the DVD/CD-RW Combo Drive control panel and the mouse.

To open a dropdown menu for options, right-click on the movie screen.

User-Installable Features

Using the Optical Drive Control Panel

The PowerDVD optical drive software allows you to watch the movie much like a VCR player. You have the option to pause, rewind, fast-forward and stop the movie at any point.

1. To Pause the movie, click the button.

2. To Rewind the movie, click the  button to rewind to a specific portion of the movie, or the  button to return to the opening screen.

3. To Fast-forward the movie, click the  button to forward to a specific portion of the movie, or the button to jump to the ending credits.

4. To Stop the movie, click the  button.

Exiting the Optical Player

1. Click the U in the upper right corner of the title bar.

USING DOLBY™ HEADPHONE

The Dolby Headphone utility lets you enjoy multichannel sound sources, such as movies, with realistic surround sound using conventional stereo headphones.

Dolby Headphone is a signal processing system that enables your stereo headphones to realistically portray the sound of a five-speaker playback system

■

Media discs which do not have the Dolby Surround 5:1 symbol will not support Dolby Headphone.

■

After making changes to Dolby Headphone and clicking OK, wait at least 10 seconds before making another change in order to allow the system to stabilize.

To use Dolby Headphones, perform the following:

1. Insert the disc in the optical drive tray. When you do so, PowerDVD will start automatically.

2. Place your cursor over the Fujitsu logo on the PowerDVD control panel and click on it. If the disc supports Dolby Surround 5.1, a menu will appear.

3. Verify that Dolby headphones is checked on the menu. If you do not want it active, select Disable.

USING THE DRIVE ON BATTERY POWER

Since optical drives consume a lot of power, your overall battery life will be shorter when operating the optical drive continuously (such as watching a DVD movie). Many movie run-times are longer than your LifeBook notebook can support on a single battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to view it in its entirety.

■

Prolonged use of the optical drive, such as watching a DVD movie, will substantially reduce your battery life. Many movie run-times are longer than your system can support on a single battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to view it in its entirety.

■

An additional battery is recommended if you will be watching DVD movies on battery power. If you don’t have an additional battery, you may purchase one either on-line at: www.shopfujitsu.com or call 1-877372-3473.

To Watch a Movie on Battery Power:

1. Have an additional fully-charged battery or your AC adapter ready for use.

2. Start watching your DVD movie.

3. When the low battery warning occurs, immediately stop the movie and exit the optical player

If you don’t stop the optical drive quickly and the notebook attempts to autosuspend (critical battery low state) the notebook will shut down improperly. If this occurs, you will need to power the system up with the power/suspend/resume button and follow any instructions that appear.

4. Manually place your notebook into suspend mode by depressing the Suspend button. Plug in a power adapter and replace the discharged battery with an additional fully-charged battery. If you do not have an additional battery, you may use the AC power adapter as your power source to continue watching the movie while recharging the installed battery.

5. Resume your notebook by pressing the Suspend button again. This step is not required if you attached AC power without entering suspend mode.

6. Restart your optical drive, locate and skip to the chapter of the movie you were last watching.

7. Continue watching your DVD movie.

Some shorter DVD movies may not require you to swap batteries or attach AC power to complete them. However, it is best to be prepared since actual battery life while operating the optical drive cannot be guaranteed.

LifeBook N6400 Series User’s Guide

AUTO INSERT NOTIFICATION FUNCTION

The Auto Insert Notification function allows your LifeBook notebook to automatically start a DVD/CD as soon as it is inserted in the optical drive and the tray is closed. Your notebook will begin playing an audio DVD/CD or will start an application if the DVD/CD includes an auto run file.

To prevent a CD from playing automatically as soon as it is inserted, refer to the related help file for your specific operating system.

Hard Disk Drive

Your Fujitsu LifeBook notebook hard disk drive capacity is dependent on which model you are using. Some LifeBook notebooks may also contain a second hard disk drive in addition to the primary hard disk drive.

(See Specifications on page 75 for more information)

FORMATTING THE HARD DISK DRIVE

The internal hard disk drive is formatted, or initialized, at the factory. You do not need to format it under normal circumstances. If you decide to reformat due to corruption or upgrade, please refer to your operating system documentation for the correct procedure.

You should not reformat your hard disk unless you are instructed to do so by Technical Support. Reformatting the hard disk drive will erase all of the data currently stored on it, including the operating system and installed programs.

Before you reformat your hard disk drive, please note:

■

Any data that currently resides on your hard disk drive must be backed-up to floppy disks or other data storage media, or it will be permanently lost. These back-up disks can then be used to reinstall and restore your data. (See your operating system manual for more

information on backing-up your data files)

■

All application software that is installed on the hard disk drive, must be reinstalled from the original source.

User-Installable Features

LifeBook N6400 Series User’s Guide

Figure 4-8. Installing/Removing PC Cards

1 PC Card Eject Button 2 PC Card Slot (bottom slot)

3 PC Card

PC Cards/ExpressCards™

Your LifeBook notebook supports Type I and Type II PC Cards and ExpressCardsTM, in separate dedicated slots.

With these cards you can perform a variety of functions depending on which type of card you install. You can install one or two cards at a time, depending on its type. PC Cards should be installed in the bottom slot and ExpressCards in the top slot. (Figure 4-8)

Some available PC/ExpressCards:

■

Wireless LAN PC Cards (Type II)

■

ExpressCard Hybrid TV Tuner

■

Local area network (LAN) cards (Type II)

■

IDE solid-state disk cards (Type II)

■

SCSI cards (Type II)

■

PC Cards that conform to PCMCIA 2.1 or CardBus

For further information, refer to the instructions supplied with your card(s).

INSTALLING PC CARDS

PC Cards are installed in the PC Card slot (Figure 4-8). To install a PC Card, follow these steps:

You may be required to log on as an Administrator or member of the Administrator’s Group to complete this procedure. If the computer is connected to a network, network policy settings may also prevent you from completing this procedure.

■

Installing or removing a PC Card during your LifeBook notebook’s shutdown or bootup process may damage the card and/or your LifeBook notebook.

■

Do not insert a PC Card into a slot if there is water or any other substance on the card as you may permanently damage the card, the notebook, or both.

1. See your PC Card manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.

2. Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards.

3. If the eject button is extended, press it until it clicks.

4. Insert the card into the slot with the label facing up.

5. Push the card firmly into the slot until it is seated in the connector.

REMOVING PC CARDS

See your PC Card manual for specific instructions on removing your card. Some cards may require your notebook to be in Suspend Mode or Off during removal.

■

Windows has a shutdown procedure for PC Cards that must be followed before removing a card. (Review your operating system manual for the correct procedure.) It is good practice to remove devices using the Unplug or Eject Hardware icon in the system tray.

■

If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applications and shut down your notebook.

2. Unlock the card from the slot by pressing the eject button. When pressed, the button will pop out.

3. Firmly press the button again until it is flush with the notebook. This will eject the card slightly out of the slot allowing you to remove the card.

If the PC Card has an external connector and cable, do not pull the cable when removing the card.

User-Installable Features

INSTALLING EXPRESSCARDS

There are two different width ExpressCards: 34 mm and 54 mm ("ExpressCard 34" and "ExpressCard 54"). (Figure 4-9). The connector inside the slot is located on the left-hand side of the slot. If you insert a 34 mm card, be sure to align it with the left side of the slot when inserting it.

34 mm

Figure 4-9 ExpressCard Sizes

ExpressCards are installed in the ExpressCard slot (the top slot). (Figure 4-10).

54 mm

■

When you receive your system, there may be a plastic slot protector installed in the ExpressCard slot. Before installing an ExpressCard, remove the slot protector in accordance with the "Removing ExpressCards" section. When you do not have a card installed in the slot, be sure to re-install the slot protector to prevent the system from being contaminated.

■

You may be required to log on as Administrator or a member of the Administrator’s Group to complete this procedure. If your computer is connected to a network, network policy settings may also prevent you from completing this procedure.

See your ExpressCard manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.

To install an ExpressCard, follow these steps:

1. Make sure there is no ExpressCard currently in the slot. If there is, see Removing ExpressCards.

2. Insert your ExpressCard into the slot with the product label facing up. If you are inserting a 34 mm card, be sure to align it with the left side of the slot when inserting it.

3. Push the card firmly into the slot until it is seated in the connector.

(An ExpressCard 54 is used in the illustration.)

Figure 4-10. Installing/Removing ExpressCards

■

1 ExpressCard Eject Button 2 ExpressCard Slot 3 ExpressCard

Installing or removing an ExpressCard during your notebook’s shutdown or bootup process may damage the card and/or your notebook. Do not insert an ExpressCard into a slot if there is water or any other substance on the card as you may permanently damage the card, your notebook, or both.

REMOVING EXPRESSCARDS

See your ExpressCard manual for specific instructions on removing your card; some cards may require your notebook to be in Suspend Mode or Off during removal.

■

Windows has a shutdown procedure for ExpressCards that must be followed before removing a card. (Review your operating system manual for the correct procedure.) It is good practice to remove devices using the Unplug or Eject Hardware icon in the system tray.

■

If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applications and shut down your notebook.

To remove an ExpressCard, press the card into the slot. This will cause the card to be ejected slightly out of the slot allowing you to remove the card.

LifeBook N6400 Series User’s Guide

Memory Upgrade Module

Your notebook has two memory slots, and the system comes with 1 GB, 2 GB, or 4 GB of factory-installed memory. If you have a module installed in only one slot, you can increase your memory capacity by installing another memory module in the empty slot or by increasing the size of the single installed module. The minimum amount of memory in your system is 1 GB.

■

Systems with Microsoft Windows Vista installed require a minimum of 512 MB of memory, but 1 GB or more is recommended.

■

If 4 GB of memory is installed in your system, only 3.25 GB are usable, due to operating system constraints.

Your notebook supports dual-channel memory, which can have a significant effect upon your system’s performance. In order to support dual-channel memory, two DIMM modules must be installed in your computer.

■

Do not remove any screws from the memory upgrade module compartment except the ones specifically shown in the directions for installing and removing the memory upgrade module.

■

The memory upgrade module can be severely damaged by electrostatic discharge (ESD). To minimize risk to the module, observe the following:

■

Before handling a memory module, touch a grounded metal object to discharge static electricity built up in your body.

■

When installing or removing a memory module, hold it by the edge so as not to touch any contacts or chips. Do not to touch any internal computer terminals or components; the oil from your fingers could cause a short to the components.

■

Power down your system before you add or remove memory modules. Even if the system is in hibernate or standby states, data could be lost or the memory could be damaged if power is still available to the system.

INSTALLING A MEMORY MODULE

1. Turn off power to your LifeBook notebook using the power/suspend/resume button, and remove any power adapter.

2. Make sure that all the connector covers are closed.

3. Turn the LifeBook notebook bottom side up, with the front panel toward you.

4. Remove the screws at the front of the memory upgrade module compartment. (Figure 4-11)

5. Remove the cover by tilting the front edge up, then pulling forward until the tabs on the cover are free.

Figure 4-11. Opening the Memory Upgrade Compartment

6. Remove the memory upgrade module from the static guarded sleeve.

7. Align the memory upgrade module with the part side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. The connector will be pointing toward the rear of the LifeBook notebook.

8. Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is properly in place. (Figure 4-12)

The installation of incompatible memory modules can cause numerous problems which could result in loss of data. Memory upgrades must be PC2-5300 DDR2-667 SO-DIMM modules. Fujitsu highly recom- mends that you only purchase additional memory from the Fujitsu on-line accessory store at: us.fujitsu.com/computers.

Figure 4-12. Installing a Memory Upgrade Module

9. Replace the cover by hooking the tabs under the rear edge of the compartment opening and tilting down until flush with the bottom of your notebook.

10. Replace the screws.

User-Installable Features

The memory upgrade module is not something you should routinely remove from your notebook. Once it is installed, you should leave it in place unless you want to increase system memory capacity.

REMOVING A MEMORY UPGRADE MODULE

1. Perform steps 1 through 5 of Installing a Memory Upgrade Module.

2. Pull the clips sideways away from each side of the memory upgrade module at the same time.

3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the rear of your LifeBook notebook. (Figure 4-13)

Figure 4-13. Removing a Memory Upgrade Module

CHECKING THE MEMORY CAPACITY

Once you have changed the system memory capacity by either adding or removing a memory upgrade module, be sure to check that your notebook has recognized the change.

You can check the memory capacity by clicking [Start]

-> Control Panel, then double-clicking the System icon. Select the General tab and check the amount of memory under “Computer.”

If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. (If the module is

properly installed and the capacity is still not correctly recognized, see Troubleshooting on page 55.

4. Store the memory upgrade module in a static guarded sleeve.

5. Replace the cover by following steps 9 and 10 of Installing a Memory Upgrade Module.

After installing your added memory module, you must complete the Resetting the Save-to-Disk Parameters procedure in order for the Save-to-Disk mode to operate properly on your LifeBook notebook.

(See Hibernation (Save-toDisk) Feature on page 33 for more information)

LifeBook N6400 Series User’s Guide

Device Ports

Your LifeBook notebook comes equipped with multiple ports to which you can connect an external device including: disk drives, keyboards, modems, printers, etc.

COMMUNICATIONS PORTS

Your LifeBook has a Modem jack (RJ-11) and a LAN jack (RJ-45) to accommodate external communications.

Modem (RJ-11) Telephone Jack

The modem (RJ-11) telephone jack is used for your internal modem. To connect the telephone cable follow these easy steps: (Figure 4-14)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

3. Plug the other end of the telephone cable into a telephone outlet.

Figure 4-15. Connecting the LAN

IEEE 1394 JACK

The 4-pin IEEE 1394 (Firewire) jack is a high-speed interface (400 Mbps) that can be used to transfer large amounts of data between your notebook and a Firewire peripheral such as a digital camera, external hard drive, or video camera. Hot-swappable and plug-n-play, it is much faster than USB 1.1, CardBus, or parallel port. To connect a 1394 device, follow these steps: (Figure 4-16)

Figure 4-14. Connecting the Modem

Do not connect the internal modem to a Digital PBX as it may cause serious damage to the modem or your LifeBook notebook. It should be noted that some hotels use the Digital PBX systems, please be sure to find out BEFORE you connect your modem. Consult your PBX manufacturer’s documentation for more information.

The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by the FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600bps at upload.

LAN PORT

This port allows you to connect a LAN (RJ-45) cable for high-speed network or broadband connections (e.g., DSL, cable modem). (Figure 4-15)

Figure 4-16. IEEE 1394 Interface

The 1394 port in this system uses a fourpin configuration. If you intend to interface with devices which have a six-pin configuration, you will need to purchase an adapter.

UNIVERSAL SERIAL BUS (USB) 2.0 PORTS

The five Universal Serial Bus (USB) 2.0 ports allow you to connect USB devices such as game pads, pointing devices, keyboards and speakers. There is one USB 2.0 port on the right side, and four on the rear panel. (Figure 4-17).

Note that only the individual horizontal USB port on the right rear of the system

can be used to connect an infrared remote control receiver that is required when using the optional Media Center Edition remote control.

USB 2.0 is downward-compatible with USB 1.1 devices, so older USB devices will work with these ports. USB 2.0 is a much faster design, running forty times faster than USB 1.1. To connect a USB device follow these steps:

User-Installable Features

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

Figure 4-17. Connecting a USB Device

S-VIDEO OUT PORT

The S-Video port allows you to connect and use directly any S-Video device, such as a VCR or television. The S-Video standard provides for a higher quality picture than Composite. In order to connect an S-Video device, follow these easy steps: (Figure 4-18)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

■

There are several types of cables for connecting a digital electronic device to the digital audio-out connector, depending on the connector type. The connector on your computer is a Optical Mini Plug (3.5mm diameter mini plug)

■

The frequency of digital sound output from the SPDIF output connector is selectable as 48.0 kHz or 44.1 kHz. If a sampling rate converter is not installed in your digital electronic device (e.g., MD player), recording is not possible. See the device user manual for more details.

■

The sound recorded through connecting a digital electronic device (e.g., MD player) to the SPDIF output connector cannot be used as digital output. All output data from the SPDIF output connector has copyright protection information included.

■

If you plug headphones into the headphone jack, you will disable the built-in stereo speakers.

■

For information about using Dolby Headphone, refer to “Using Dolby™ Headphone” on page 43.

Figure 4-18. S-Video Jack

MICROPHONE JACK

The microphone jack allows you to connect an external stereo microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your LifeBook notebook. In order to connect a microphone follow these easy steps:

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

HEADPHONE/SPDIF JACK

The headphone jack allows you to connect headphones or powered external speakers to your LifeBook notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug.

The SPDIF function of the jack allows you to download digital audio to MiniDisc recorders. It uses SPDIF (Sony Philips Digital Interface) format. Use the following setting when using the digital audio-out connector.

To connect headphones or speakers, follow these steps:

EXTERNAL VIDEO PORT

The external video port allows you to connect an external monitor or LCD projector. In order to connect an external device follow these easy steps:

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

3. Tighten the two hold-down screws, located on each end of the connector.

Pressing the [Fn] + [F10] keys allows you to change your selection of where to send your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external device only, finally moving to both the built-in display panel and an external video device.

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated

Figure 4-19. External Video Connection

LifeBook N6400 Series User’s Guide

Troubleshooting

LifeBook N6400 Series User’s Guide

Troubleshooting

Your LifeBook notebook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.

IDENTIFYING THE PROBLEM

If you encounter a problem, go through the following procedure before pursuing further troubleshooting:

1. Turn off your LifeBook notebook.

2. Make sure the AC adapter is plugged into your LifeBook notebook and to an active AC power source.

3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.

4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.

5. Turn on your LifeBook notebook. Make sure it has been off at least 10 seconds before you turn it on.

6. Go through the boot sequence.

7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information

Troubleshooting

If you keep notes about what you have tried, your support representative may be able to help you more quickly by giving additional suggestions over the phone.

8. If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative:

■

Toll free: 1-800-8Fujitsu (1-800-838-5487) E-mail: 8fujitsu@us.fujitsu.com/computers Website: http://www.computers.us.fujitsu.com/support

Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:

■

Product name

■

Product configuration number

■

Product serial number

■

Purchase date

■

Conditions under which the problem occurred

■

Any error messages that have occurred

■

Type of device connected, if any

See the Configuration Label on the bottom of your LifeBook notebook for configuration and serial numbers.

Do not return a failed LifeBook notebook to Fujitsu until you have received a Return Material Authorization (RMA) number from a support representative.

LifeBook N6400 Series User’s Guide

SPECIFIC PROBLEMS

Using the Troubleshooting Table

When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty.

TROU BLE S HOO TING TABL E

You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your LifeBook notebook.

Problem Possible Cause Possible Solutions

Audio Problems

There is no sound coming from the built-in speakers.

The volume is turned too low. Adjust the volume control on your notebook.

The software volume control is set too low.

Headphones are plugged into your notebook.

BIOS audio settings are incorrect.

Software driver is not configured correctly.

Problem Page

Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 56

DVD/CD-ROM Drive Problems . . . . . . . . . . . . page 56

Hard Drive Problems. . . . . . . . . . . . . . . . . . . . . . page 57

Keyboard or Mouse Problems . . . . . . . . . . . . . . page 57

Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 58

Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 58

USB Device Problems . . . . . . . . . . . . . . . . . . . . . page 58

PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 58

Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 59

Shutdown and Start-up Problems . . . . . . . . . . . page 60

Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 61

Adjust the sound volume control settings in your software, operating system and applications.

Plugging in headphones disables the built-in speakers, remove the headphones.

Set the BIOS setup utility to the default values within the Multimedia Device Configuration menu. (See

BIOS Setup Utility page 29 for more information)

Refer to your application and operating system documentation for help.

DVD/CD-ROM Drive Problems

Notebook fails to recognize DVD/CDs.

Sound may be set to Mute. Click on the Volume icon in the notification area

and verify that the Mute checkbox is not set.

Device Manager may not be set correctly.

Go to the Control Panel -> System, and click on the Hardware tab. Click [Device Manager] and scroll down to verify that all devices are set properly.

DVD/CD is not pushed down onto center circle of the drive.

DVD/CD-ROM tray is not latched shut.

Wrong drive designator was used for DVD/CD in the application.

Open the DVD/CD-ROM tray and re-install the disk properly.

Push on the front of the DVD/CD-ROM tray until it latches.

Verify that the drive designator used by the application is the same as that used by the operating system. When the operating system is booted from a DVD/ CD, drive designations are automatically adjusted.

Windows DVD/CD Auto Insert Notification function is disabled.

Start the DVD/CD from the desktop or application software or re-enable the Windows DVD/CD Auto Insert Notification function. (See Auto Insert Notifi-

cation Function page 44 for more information)

DVD/CD is dirty or defective. Wipe DVD/CD with a non-abrasive CD cleaning

cloth and reinsert. If it still will not work try another DVD/CD in the drive.

Problem Possible Cause Possible Solutions

LifeBook notebook fails to auto-play DVD movie.

DVD Player Software is not installed.

Troubleshooting

Install DVD Player Software using the DVD Application.

The DVD/CD-ROM Access indicator on the Status Indicator Panel blinks at regular intervals when no disk is in the tray or the DVD drive is not installed.

Hard Drive Problems

You cannot access your hard drive.

Keyboard or Mouse Problems

The built-in keyboard does not seem to work.

Country designator could be set incorrectly.

The Windows DVD/CD Auto Insert Notification function is active and is checking to see if a DVD/CD is ready to run.

The setup utility is incorrectly set for your internal hard drive.

The wrong drive designator was used by an application when a bootable CD-ROM was used to start the notebook.

Security is set so your operating system cannot be started without a password.

The hard disk drive has crashed.

Your application has locked out your keyboard.

Select the DVD player software from the programs list and right-click on the window. Select Properties and verify that the region selected is “USA, Canada.”

This is normal. However, you may disable this feature. (See Auto Insert Notification Function

page 44 for more information)

Set Primary Master correctly in the BIOS. (See BIOS Setup Utility page 29 for more information)

Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted.

Verify your password and security settings.

Contact Fujitsu or your local authorized reseller for a replacement hard disk drive.

Try to use your integrated pointing device to restart your system. If this fails, turn your notebook off using the power/suspend/resume button, wait 10 seconds or more, and then turn it back on.

You have installed an external keyboard or mouse, and it doesn’t work.

You have connected an external keyboard or a mouse and it seems to be locking up the system.

The NumLk key is set. Press the NumLk key to reset it.

Your external device is not properly installed.

Your operating system is not set up with the correct driver

Reinstall your device. (See Device Ports page 50 for

more information)

Check your device and operating system documentation and activate the proper driver.

for that device.

Your operating system software is not set up with the

Check your device and operating system documentation and activate the proper driver.

correct driver for that device.

Your system has crashed. Try to restart your LifeBook notebook. If that fails,

turn off the power using the power/suspend/resume button, wait at least 10 seconds, and then power on. If turning off power with the power/suspend/resume button fails, the button has likely been set to suspend or hibernate. In that case, disconnect the power cord, then remove and re-insert the battery.

LifeBook N6400 Series User’s Guide

Problem Possible Cause Possible Solutions

Memory Problems

Your Main menu of the BIOS setup utility informa-

Your memory upgrade module

is not properly installed. tion, does not show the correct amount of installed memory.

You have a memory failure. Check for POST messages. (See Power On Self Test

Modem Problems

Remove and reinstall your memory upgrade module. (See Memory Upgrade Module page 48 for

more information)

Messages page 63 for more information)

Messages about modem operation.

USB Device Problems

You have installed a USB device, but your LifeBook notebook does not recognize the device, or the device does not seem to work properly.

PC Card Problems

A card inserted in the PC Card slot does not work or is locking up the system.

Messages about operation are

generated by whichever

modem application is in use.

The USB device is not properly

installed and/or powered.

The USB port is not enabled in

the BIOS.

The device is not properly

installed.

The device may have been

installed while an application

was running, so your notebook

is not aware of its installation.

Your software may not have

correct software driver active.

You may have the wrong I/O

address selected for your

device.

Your device and another device

are assigned the same I/O

address.

The card is not properly

installed.

Your software may not have

the correct driver active.

See your application software documentation for additional information.

Verify the USB is properly installed by unplugging and replugging the plug. Also, verify that sufficient power is available to the USB device.

Verify the USB port is Enabled in the BIOS. (See

Entering the BIOS Setup Utility page 27 for more information)

Remove and reinstall the device. (See Device Ports page 50 for more information)

Close the application and restart your LifeBook notebook.

See your software documentation and activate the correct driver.

See your device documentation and software documentation to determine the required I/O address. Change the settings in the BIOS setup utility. (See

BIOS Setup Utility page 29 for more information)

Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.

Remove and reinstall the card. (See Removing PC

Cards page 46 for more information)

See your software documentation and activate the correct driver.

The card may have been

installed while an application

Close the application and restart your LifeBook

notebook. was running, so your notebook is not aware of its installation.

You may have the wrong I/O address selected for your PC Card device.

See your PC Card documentation to determine

the required I/O address. Change the settings in

the BIOS. (See BIOS Setup Utility page 29 for more

information)

Problem Possible Cause Possible Solutions

A card inserted in the PC Card slot does not work or is locking up the system.

(continued)

Power Failures

You turn on your LifeBook notebook and nothing seems to happen.

Troubleshooting

Your PC Card device and another device are assigned the same I/O address.

The installed primary battery is discharged, there’s no second battery installed or there is no AC adapter installed.

The battery is installed but is faulty.

Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.

Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel page 15 for more information) Install a charged battery or a Power adapter.

Use the Status Indicator panel to verify the presence and condition of the batteries. (See Status Indicator Panel page 15 for more information) If a battery is indicating a short, remove that battery and operate from another power source or replace that battery.

The battery or batteries are low. Check the Status Indicator Panel to determine the

presence and condition of the batteries. (See Status Indicator Panel page 15 for more information) Use a Power adapter to operate until a battery is charged or install a charged battery.

Your LifeBook notebook turns off all by itself.

Your LifeBook notebook will not work on battery alone.

The AC adapter is not plugged in properly.

The Power adapter has no power from the AC outlet.

Verify that your adapter is connected correctly. (See

Power Sources page 27 for more information)

Move the AC cord to different outlet, check for a line switch or tripped circuit breaker for the AC outlet.

The AC adapter is faulty. Try a different Power adapter.

The power management parameters are set for auto timeouts which are too short for your operating needs.

Press any button or key on the keyboard, or move the mouse. If that fails, push the Power/Suspend/ Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs.

You ignored a low battery alarm until the battery is dead and your machine has gone

Install a power adapter and then push the Power and Suspend/Resume button. (See Power Sources page 27

for more information)

into Dead Battery Suspend mode.

Your power adapter has failed or lost its power source.

Make sure the adapter is plugged in and the outlet has power.

You have a battery failure. Verify the condition of the batteries using the Status

Indicator panel, and replace or remove any batteries that are shorted. (See Status Indicator Panel page 15

for more information)

The installed batteries are dead.

Replace the battery with a charged one or install an AC adapter.

No batteries are installed. Install a charged battery.

The batteries are improperly installed.

Verify that the batteries are properly connected by re-installing them.

LifeBook N6400 Series User’s Guide

Problem Possible Cause Possible Solutions

Your LifeBook notebook will not work on battery

Your installed batteries are faulty.

alone.

Verify the condition of the batteries using the Status

Indicator panel and replace or remove any batteries

that are shorted. (See Status Indicator Panel page 15

for more information)

The batteries seem to discharge too quickly.

You are running an application that uses a great deal of power due to frequent hard drive or DVD/CD-ROM access, or use of a modem or LAN PC card.

The power savings features may be disabled.

The brightness is turned all the way up.

The batteries are very old. Replace the batteries.

The batteries have been exposed to high temperatures.

The batteries are too hot or too cold.

Shutdown and Startup Problems

The Power and Suspend/ Resume button does not work.

The Power and Suspend/ Resume button is disabled from the Power -> Advanced submenu of the setup utility.

You did not hold the button in long enough.

Use both the primary battery and an optional

second battery and/or use a power adapter for this

application when at all possible.

Check the power management and/or setup utility

settings in the Power Savings menu and adjust

according to your operating needs.

Turn down the brightness adjustment. The higher

the brightness the more power your display uses.

Replace the batteries.

Restore the notebook to normal operating tempera-

ture. The Status Indicator panel Charging icon will

flash when the battery is out of operating range.

Enable the button from the setup utility.

Hold the button longer. This may need to be a few

seconds if your application is preventing the CPU

from checking for button pushes.

The system powers up and displays power-on information, but fails to load the operating system.

Your system display won’t turn on when the system is turned on or when the system has resumed.

There may be a conflict with the application software.

The boot sequence settings of the setup utility are not compatible with your configuration.

You have a secured system requiring a password to load your operating system.

Internal hard drive was not detected.

The system may be passwordprotected.

Close all applications and try the button again.

Set the operating source by pressing the [ESC] key

while the Fujitsu logo is on screen or use the [F2]

key and enter the setup utility and adjust the source

settings from the Boot menu. (See BIOS Setup

Utility page 29 for more information)

Make sure you have the right password. Enter the

setup utility and verify the Security settings and

modify them accordingly. (See BIOS Setup Utility

page 29 for more information)

Use the BIOS setup utility or Primary Master

submenu, located within the Main menu, to try to

auto detect the internal hard drive.

Check the status indicator panel to verify that the

Security icon is blinking. If it is blinking, enter your

password.

Problem Possible Cause Possible Solutions

An error message is displayed on the screen during the notebook (boot) sequence.

Power On Self Test (POST) has detected a problem.

Troubleshooting

See the POST messages to determine the meaning and severity of the problem. Not all messages are errors; some are status indicators. (See Power On Self

Test Messages page 63 for more information)

Your notebook appears to change setup parameters when you start it.

Video Problems

The display is blank when you turn on your notebook.

The notebook turned on with a series of beeps and your display is blank.

Your system display won’t turn on when the system is turned on or when the system has resumed.

BIOS setup changes were not saved when you exited the BIOS setup utility, returning it to previous settings.

The BIOS CMOS hold-up battery has failed.

Something is pushing on the Closed Cover switch.

The display angle and brightness settings are not adequate for your lighting conditions.

The LifeBook notebook is set for an external video device only.

The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again.

Power On Self Test (POST) has detected a failure which does not allow the display to operate.

The system may be passwordprotected.

Make sure you select Save Changes And Exit when exiting the BIOS setup utility.

Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years.

Clear the Closed Cover switch. (See Figure on page 8

for location)

Press the [Fn] + [F7] keys repeatedly until you have the desired brightness.

Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.

Press any button or key on the keyboard, or move the mouse to restore operation. If that fails, push the Power and Suspend/Resume button. (The display may be shut off by Standby mode, Auto Suspend or Video Timeout.)

Contact your support representative.

Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.

The display goes blank by itself after it is used.

Something is pushing on the Closed Cover switch.

The notebook has gone into Video timeout, Standby mode, Suspend mode or Save-to-Disk mode because you have not used it for a period of time.

Check the Closed Cover switch. (See Figure on page

8 for location)

Press any button or key on the keyboard, or move the mouse to restore operation. If that fails, push the power/suspend/resume button. Check your power management settings, or close all applications and go to Power Savings in the setup utility to adjust the timeout values to suit your operation needs. (See

BIOS Setup Utility page 29 for more information)

LifeBook N6400 Series User’s Guide

Problem Possible Cause Possible Solutions

The display goes blank by itself after it is used.

(continued)

The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again.

The built-in display does not close.

A foreign object, such as a paper clip, is stuck between the display and the keyboard.

The built-in display has bright or dark spots.

If the spots are very tiny and few in number, this is normal for a large LCD display.

If the spots are numerous or large enough to interfere with your operation needs.

You have connected an external video device and it does not come on.

The application display uses only a portion of your screen and is surrounded by a dark frame.

Your external video device is not compatible with your LifeBook notebook.

You are running an application that does not support 800 x 600 pixel resolution display and display compression is enabled.

You have connected an external video device and it

Your BIOS setup is not set to enable your external device.

does not display any information.

Your external video device is not properly installed.

Your operating system software is not set up with the correct driver for that device.

Miscellaneous Problems

Error message is displayed on the screen during the operation of an application.

Application software often has its own set of error message displays.

Press any button or key on the keyboard, or move the

mouse to restore operation. If that fails, push the

Power and Suspend/Resume button. (The display

may be shut off by Standby Mode, Auto Suspend or

Video Timeout.)

Remove all foreign objects from the keyboard.

This is normal; do nothing.

Display is faulty; contact your support representative.

See your monitor documentation and the External

Monitor Support portions of the Specifications

section on page 75.

Display compression gives a clearer but smaller

display for applications that do not support 800 x

600 pixel resolution. You can fill the screen but have

less resolution by changing your display compres-

sion setting, (See Video Features submenu, located

within the Advanced menu of the BIOS.) (See BIOS

Setup Utility page 29 for more information)

Toggle the video destination by pressing [Fn] and

[F10] together, or check the BIOS setup and enable

your external video device. (See Video Features

submenu, located within the Advanced Menu of the

BIOS.) (See BIOS Setup Utility page 29 for more

information)

Reinstall your device. (See External Video Port

page 51 for more information)

Check your device and operating system

documentation and activate the proper driver.

See your application manual and help displays

screens for more information. Not all messages are

errors some may simply be status.

Troubleshooting

POWER ON SELF TEST MESSAGES

The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. The most common errors are marked with a #. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.

nnnn Cache SRAM Passed

Where nnnn is the amount of system cache in kilobytes successfully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)

*Diskette drive A error or Diskette drive B error

Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility page 29 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative.

*Extended RAM Failed at offset: nnnn

Extended memory not working or configured improperly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is properly installed, check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.

nnnn Extended RAM Passed

Where nnnn is the amount of memory in kilobytes successfully tested.

*Failing Bits: nnnn The hex number nnnn

This is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.

*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4)

The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.

*Incorrect Drive A type – run SETUP

Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.

*Incorrect Drive B type – run SETUP

Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.

*Invalid NVRAM media type

Problem with NVRAM access. In the unlikely case that you see this message you may have some display problems. You can continue operating but should contact your support representative for more information.

*Keyboard controller error

The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then.

*Keyboard error

Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.

*Keyboard error nn

BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.

*Monitor type does not match CMOS – Run SETUP

Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.

#*Operating system not found

Operating system cannot be located on either drive A: or drive C:. Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted and your system may have to be reinstalled from your back up media.

*Parity Check 1 nnnn

Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data-destroying failure. Contact your support representative.

LifeBook N6400 Series User’s Guide

*Parity Check 2 nnnn

Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative.

#*Press <F1> to resume, <F2> to SETUP

Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings.

#*Previous boot incomplete – Default configuration used

Previous Power On Self Test did not complete successfully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power with the power/suspend/ resume button and contact your support representative.

*Real time clock error

Real-time clock fails BIOS test. May require board repair. Contact your support representative.

*Shadow RAM Failed at offset: nnnn

Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corruption if you continue. Contact your support representative.

nnnn Shadow RAM Passed

Where nnnn is the amount of shadow RAM in kilobytes successfully tested.

*System battery is dead – Replace and run SETUP

The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your LifeBook notebook. This battery has an expected life of 2 to 3 years.

System BIOS shadowed

System BIOS copied to shadow RAM.

nnnn System RAM Passed

Where nnnn is the amount of system memory in kilobytes successfully tested.

*System timer error

The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.

UMB upper limit segment address: nnnn

Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.

Video BIOS shadowed

Video BIOS successfully copied to shadow RAM.

MODEM RESULT CODES

The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes.

Examples of result codes are:

■

NO CARRIER

■

NO DIALTONE

■

CONNECT 53000 (Connection complete at 53,000 bps.)

■

ERROR

■

FAX

■

RING (This means an incoming call.)

■

BUSY

■

NO ANSWER

When using the internal modem with applications that are not factory installed refer to the application documentation.

*System CMOS checksum bad – run SETUP

BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.

*System RAM Failed at offset: nnnn

System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.

Troubleshooting

Restoring Your Pre-installed Software

The Drivers and Applications Restore (DAR) disc contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your computer configuration for use as documented below.

If you have access to the internet, visit the Fujitsu Support website at: http:// www.computers.us.fujitsu.com/support to check for the most current information, drivers and hints on how to perform recovery and system updates.

Re-Installing Individual Drivers and Applications

The Drivers and Applications disc can be used to selectively re-install drivers and/or applications that may have been un-installed or corrupted.

There may be certain free third-party applications pre-installed on your system that are not on the DAR disc. The latest versions of the applications can be downloaded from the third-party’s website.

To re-install drivers and/or applications:

1. Boot up the system and insert the DAR disc after Windows has started. A Fujitsu Installer screen is displayed after the disc is inserted.

2. After reading the License Agreement, click [I agree].

3. A window will appear containing a list of applications, drivers, and utilities that you can install from the Drivers and Applications disc

The components listed are color-coded in terms of their install status. Blue indicates that the component can be installed. Green indicates that the component needs to be installed separately. Grey indicates a component that is already installed; grey items can be reinstalled, but prior to installation you will receive a reminder that the component is already installed.

4. In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately.

5. Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed.

6. After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system.

RESTORING THE FACTORY IMAGE

The Recovery and Utility Disc only restores the primary hard disk drive. If you have an optional second hard disk drive installed, it will not be restored using these utilities.

The Recovery and Utility Disc that came with your system contains two utilities:

■

The Recover y utility allows you to restore the original contents of the C: drive.

■

The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.

• The use of this disc requires that you have a device capable of reading DVDs attached to your system. If you do not have a built-in DVD player, you will need to attach an external player. For more information on available external devices, visit our Website at: us.fujitsu.com/ computers.

• This disc can only be used with the system with which it was purchased.

BOOT Priority Change

Before restoring an image, you must first verify that your system is set up to boot from the DVD drive. To verify/change the boot-up priority (rather than bootingup from the hard drive or an external floppy disk drive), perform the following steps:

1. Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.

2. Using the arrow keys, go to the Boot menu.

3. Arrow down to the Boot Device Priority submenu. Press [Enter].

4. If “Optical Media Drive” or “CD-ROM Drive” is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the top of the list. (The system attempts to boot from the devices in the order in which they are

LifeBook N6400 Series User’s Guide

listed.). Note that the BIOS for some systems will indicate “CD-ROM Drive”, even when a DVD drive is connected.

5. If you have an external DVD drive connected, proceed to the next step; otherwise, proceed to step 7.

6. If you have an external DVD drive connected:

• Select the Advanced menu in the BIOS window.

• Scroll down to the USB Features submenu and press the Enter key to open it.

• If Legacy USB Support is disabled, press the space bar to enable it.

• Scroll down to SCSI SubClass Support and press the space bar to enable it.

7. Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.

After you have changed the boot priority, you can restore a backup image when you are booting up.

Procedure

1. Turn on the power to your system.

2. Ensure that you have a device that can read DVDs

either installed in your system or attached externally to it.

3. Insert the Recovery and Utility Disc into the drive

tray.

4. Reboot your system.

5. After the system reboots, follow the instructions

that appear to either restore your system image or erase all data from your hard disk.

agreement. After clicking on the icon, the FDU automatically connects with the Fujitsu site to check for updates and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be used while the download is in process. When the update is complete, a message appears informing you of the fact.

■

Enable Automatic Update Notifications

Automatically searches for new updates on a regular basis (approximately every 3 days).

■

Show update history

Brings up a screen that displays a history of updates that have been made via the FDU.

■

About Fujitsu Driver Update

Displays the FDU version number and copyright information

■

Fujitsu Driver Update Readme

Displays the FDU readme.

AUTOMATICALLY DOWNLOADING DRIVER UPDATES

To invoke the FDU menu, right-click on the FDU icon. The menu contains the following items:

■

Check for updates now

Allows for manual driver update search. The first

time it is used, you are prompted to agree to a user

Care and Maintenance

LifeBook N6400 Series User’s Guide

Care and Maintenance

If you use your LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices

■

The system contains components that can be severely damaged by electrostatic discharge (ESD). To minimize risk to the components, observe the following precautions:

■

Before docking or undocking your LifeBook notebook (when using a port replicator), it is a good practice to always touch a grounded metal object to discharge static electricity built up in your body.

■

Be sure to power down your system before adding or removing system components. Even if the system is in hibernate or standby states, data could be lost or memory could be damaged if power is still available to the system.

■

When installing or removing a memory module, hold it by the edge so as not to touch any contacts or chips. Be careful not to touch any internal computer terminals or components; the oil from your fingers could cause a short to the components.

■

Electrical equipment may be hazardous if misused. Operations of this product or similar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.

LIFEBOOK NOTEBOOK

Caring for your Notebook

■

Your LifeBook notebook is a durable but sensitive electronic device. Treat it with care.

■

Make a habit of transporting it in a carrying case.

■

Do not attempt to service the computer yourself. Always follow installation instructions closely.

■

Do not operate the notebook in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.

■

Keep it away from food and beverages.

Care and Maintenance

■

If you accidentally spill liquid on your notebook:

■

Turn it off and position it so the liquid can run out.

■

Let it dry out for 24 hours, or longer if needed.

■

If your notebook will not boot after it has dried out, call your support representative.

■

Do not use your LifeBook notebook in a wet environment (near a bathtub, swimming pool).

■

Always use the AC adapter and batteries that are approved for your LifeBook notebook.

■

Avoid exposure to sand, dust and other environmental hazards.

■

Do not expose your LifeBook notebook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your notebook.

■

Keep the covers closed on the connectors and slots when they are not in use.

■

Do not put heavy or sharp objects on the computer.

■

If you are carrying your LifeBook notebook in a briefcase, or any other carrying case, make sure that there are no objects in the case pressing on the lid.

■

Do not drop your LifeBook notebook.

■

Do not touch the screen with any sharp objects.

Cleaning your LifeBook notebook

■

Always disconnect the power plug. (Pull the plug, not the cord.)

■

Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.

■

Use a soft cloth to remove dust from the screen. Never use glass cleaners.

Storing your LifeBook notebook

■

If storing your LifeBook notebook for a month or longer, turn your LifeBook off and remove all Lithium ion batteries.

■

Store your LifeBook notebook and batteries separately. If you store your notebook with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your notebook.

■

Store your notebook in a cool, dry location. Temperatures should remain between 13ºF (-25ºC) and 140ºF (60ºC).

LifeBook N6400 Series User’s Guide

Traveling with your LifeBook notebook

■

Do not transport your LifeBook notebook while it is turned on.

■

Do not check your LifeBook notebook as baggage. Carry it with you.

■

When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive handinspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine.

■

Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.

Outlet Type Location

United States, Canada, Mexico, parts of Latin America, Japan, Korea, the Philippines, Taiwan

Russia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South Asia

United Kingdom, Ireland, parts of Africa, Malaysia, Singapore

Increasing Battery Life

■

Power your LifeBook notebook through the AC adapter whenever possible.

■

If your LifeBook notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.

■

Keep brightness to the lowest level comfortable.

■

Set the power management for maximum battery life.

■

Put your LifeBook notebook in Suspend mode when it is turned on and you are not actually using it.

■

Minimize your DVD/CD-RW drive, CD-ROM drive, and wireless LAN usage.

■

Disable the Windows CD Auto Insert function.

■

Always use fully charged batteries.

■

Eject PCMCIA cards when not in use.

FLOPPY DISKS AND DRIVES

Caring for your Floppy Disks

■

Avoid using floppy disks in damp or dusty locations.

■

Never store floppy disks near a magnet or magnetic field.

■

Do not use a pencil or an eraser on a disk or disk label.

■

Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).

■

Do not touch the exposed part of the disk behind the metal shutter.

China, Australia, New Zealand

BATTERIES

Caring for your Batteries

■

Always handle batteries carefully.

■

Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.

■

Do not drop, puncture, disassemble, mutilate or incinerate the battery.

■

Recharge batteries only as described in this manual and only in ventilated areas.

■

Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.

■

Do not leave a battery in storage for longer than six months without recharging it.

Caring for your Floppy Disk Drive

■

To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.

■

Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).

■

Keep the floppy disk drive out of direct sunlight and away from heating equipment.

■

Avoid storing the floppy disk drive in locations subject to shock and vibration.

■

Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy disk drive or disk.

■

Never disassemble or dismantle your floppy disk drive.

Care and Maintenance

DVDs AND CDs

Caring for your DVDs and CDs

DVDs and CDs are precision devices and will function reliably if given reasonable care.

■

Always store your DVD/CDs in its case when it is not in use.

■

Always handle DVD/CDs by the edges and avoid touching the surface.

■

Avoid storing any DVD/CDs in extreme temperatures.

■

Do not bend DVD/CDs or set heavy objects on them.

■

Do not spill liquids on DVD/CDs.

■

Do not scratch DVD/CDs.

■

Do not put a label on DVD/CDs.

■

Do not get dust on DVD/CDs.

■

Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.

■

If a DVD/CD is subjected to a sudden change in temperature, cold to warm, condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry DVD/CDs.

■

If a DVD/CD is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.

PC CARDS

Caring for your PC Cards

PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Card will provide specific information, but you should pay attention to the following points:

■

To keep out dust and dirt, store PC Cards in their protective sleeves when they are not installed in your LifeBook notebook.

■

Avoid prolonged exposure to direct sunlight or excessive heat.

■

Keep the c ards dr y.

■

Do not flex or bend the cards, and do not place heavy objects on top of them.

■

Do not force cards into the slot.

■

Avoid dropping cards, or subjecting them to excessive vibration.

Caring for your Media Drive

Your media drive is durable but you must treat it with care. Please pay attention to the following points:

■

The drive rotates the compact disk at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.

■

Avoid using or storing the drive where it will be exposed to extreme temperatures.

■

Avoid using or storing the drive where it is damp or dusty.

■

Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.

■

Avoid using or storing the drive where it will be subjected to shock or vibration.

■

Do not disassemble or dismantle the media drive.

LifeBook N6400 Series User’s Guide

System Specifications

LifeBook N6400 Series User’s Guide

Specifications

This section provides the general hardware and environmental specifications for your LifeBook notebook. Specific details about your system may vary from those referenced here. For an updated list of current configurations, please go to the Fujitsu Computer Systems Corporation Website at: us.fujitsu.com/computers.

All options listed are accurate as of the date of print; substitutions may have been made subsequent to date of publication.

CONFIGURATION LABEL

Your LifeBook notebook contains a configuration label located on the bottom of the system. This label contains specific information regarding the options you’ve chosen for your notebook. Following is an example label and information about its various parts. Your label may vary, depending upon your system configuration.

FPC ID

No:

Part No: FPC0xxxxxxxxxxxxx

N6420, 17WXGA+, T5600, XPP, DL S-MULTI, 1GB, 200G, MDM/LAN, WLAN

Model

Screen Size

Processor

Figure 7-1 Configuration Label

Configuration ID

ALOxxxxxxxxxxx

Operating System

Memory

Optical Device

Hard Drive Size

Communications Devices

MICROPROCESSOR

Intel® Core™ 2 Duo processor T7200 or T5600

■

T7200 processor: 2.00 GHz processor speed with 667 MHz Front Side Bus (FSB) and 4 MB on-die L2 cache

■

T5600 processor: 1.83 GHz processor speed with 667 MHz FSB and 2 MB on-die L2 cache

MEMORY

System Memory Range:

■

Factory-installed maximum is 4 GB. If purchased with less than the maximum, the user can purchase larger and/or additional modules.

■

DDR2-667 MHz, PC5300

■

2 DIMM slots

■

Supports dual-channel memory (requires that two DIMM modules be installed)

BIOS Memory:

8 Mbit

VIDEO

■

Built-in 17" Color Enhanced Crystal View flat-panel Wide XGA+ TFT active matrix Crystal View (high contrast: 600:1 contrast ratio; high brightness: 370 nits) LCD display with simultaneous display capability.

■

Visual Optimizer button to dynamically and automatically enhance video images for optimal quality.

Video Color and Resolution

■

Internal: WXGA+, 1440 x 900 pixel resolution, 16M colors max

■

External: 1600 x 1200 pixel resolution, 16M colors.

■

Simultaneous: 1024 x 768 pixel resolution, 16M colors max

Graphics Accelerator Card

■

ATI Mobility™ Radion® X1600 graphics with 512 MB of HyperMemory™ (256 MB dedicated video memory and 256 MB shared memory), or,

■

ATI Mobility™ Radion® X1400 graphics with 256 MB of HyperMemory™ (128 MB dedicated video memory and 128 MB shared memory)

AUDIO

The Intel 945PM controller supports Intel High Definition (HD) Audio. HD Audio delivers the features and high-end performance of an add-in audio card, and is capable of playing back more channels of higher quality than was previously possible.

■

Intel 82801GBM/ALC262

■

Stereo headphone/SPDIF jack, 1 V minimum impedance 32 Ohms

■

Stereo microphone jack, 100mV impedance 10K Ohms

■

Two built-in stereo box speakers (1.5W/channel) and

or less,

rms

or less, minimum

rms

subwoofer

MASS STORAGE DEVICES

Hard Disk Drives

■

Optional second hard disk drive (Note that the optional second hard disk drive is a factory-installed option, and cannot be purchased as an accessory.)

■

Hard Disk Drive configurations available: 160 GB (4200 rpm) 200 GB (4200 rpm) 100 GB (5400 rpm) + 100 GB (5400 rpm) = 200 GB 100 GB (7200 rpm) + 100 GB (7200 rpm) = 200 GB 160 GB (4200 rpm) + 160 GB (4200 rpm) = 320 GB 200 GB (4200 rpm) + 200 GB (4200 rpm) = 400 GB

LifeBook N6400 Series User’s Guide

Optical Drive

■

Dual-Layer Multi-Format DVD Writer: 24x CD-R, 10x CD-RW, 8x DVD-R, 4x DVD-RW, 2x DVD-R DL, 8x DVD+R, 4x DVD+RW, 2.4x DVD+R DL, 5x DVDRAM, or,

■

HD DVD-ROM drive: 1x HD DVD-ROM, 24x CDROM, CD-R (24x read, 16x write), CD-RW (24 x read, 10x write), 8x DVD-ROM, DVD-R (8x read, 4x write), DVD-R DL (4x read, 2x write), 4x DVD-RW, DVD+R (8x read, 4x write), DVD+R DL (4x read, 2.4x write), 4x DVD+RW, 3x DVD-RAM.

FEATURES

Integrated Pointing Device

Touchpad, with two buttons and a fingerprint recognition sensor/scroll button

Theft Prevention Lock Slot

Lock slot for use with physical restraint security systems.

Biometric Security

Fingerprint recognition sensor helps to guard against unauthorized system access.

Communications

■

Integrated Broadcom 10 Base-T/100 Base-TX/1000 Base-T Gigabit Ethernet LAN

■

Internal V.90 standard 56K* fax/modem (ITU V.90, 56K data, 14.4K fax).

■

Integrated Intel PRO/Wireless 3945ABG network connection (802.11a+b/g)

* Actual data transfer rate over U.S. telephone lines varies and is

less than 56Kbps due to the current FCC regulations and line conditions.

DEVICE PORTS

■

PC Card slot for one Type II cards: PCMCIA Standard

2.1 with CardBus support

■

ExpressCard slot for one ExpressCard (supporting either 34mm or 54mm ExpressCards)

■

One 15-pin D-SUB connector for VGA external monitor or LCD projector (see Display specifications)

■

Combination Memory Stick/Secure Digital (SD)/xD Card slot

■

One mini-DIN 7-pin S-Video Out port

■

Five connectors for USB 2.0 (Universal Serial Bus) input/output devices

■

One 4-pin IEEE 1394 jack

■

One stereo microphone/line in jack (See Audio specifications)

■

One stereo headphone/line out jack (See Audio specifications)

■

One modular modem (RJ-11) connector

■

One modular LAN (RJ-45) connector

KEYBOARD

Built-in keyboard with all functions of 103 key keyboards.

■

Total number of keys: 103

■

Function keys: 12, [F1] through [F12]

■

Feature extension key: [Fn]

■

Windows keys: 2 (Start key and application key)

■

Key pitch: 19 mm

■

Key stroke: 3.0 mm

■

Dedicated ten-key numeric keypad

■

Built-in Alps Wide Touchpad pointing device with left and right buttons and scrolling button

External Keyboard Support

■

USB-compatible

External Mouse Support

■

USB-compatible

Management Standard

DMI 2.0-ready, WFM 2.0-compliant

POWER

Batteries

Main 6-cell Lithium ion battery, rechargeable, 10.8V, 4000 mAh

Adapters

AC Adapter: Autosensing 100-240V AC, 150W, supplying 19V DC, 7.90A, to the LifeBook notebook (includes an AC cable).

Power Management

Conforms to ACPI (Advanced Configuration & Power Interface)

DIMENSIONS

Overall Dimensions

15.87" x 11.61" x 1.79"/2.02" (403 mm x 295 mm x 45.5/51.3 mm)

We i gh t

Non-TV tuner model (with one hard disk drive): Approximately 9.92 lbs. (4.5 Kg)

TV tuner model (with one hard disk drive): Approximately 10.12 lbs. (4.59 Kg)

TV tuner model (with two hard disk drives): Approximately 10.58 lbs. (4.8 Kg)

ENVIRONMENTAL REQUIREMENTS

Te mp e r at u r e

Operating: 5° to 35° C (41° to 95° F) Non-operating: –15° to 60° C (5° to 140° F)

Humidity

Operating: 20% to 85%, relative, non-condensing. Non-operating; 8% to 85%, relative, non-condensing

Altitude

Operating: 10,000 feet (3,048 m) maximum

POPULAR ACCESSORIES

For information on ordering Fujitsu accessories, please visit our Website at: www.shopfujitsu.com or call 1-877-372-3473.

Specifications

PRE-INSTALLED SOFTWARE

Depending on your pre-installed operating system, your Fujitsu LifeBook notebook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. The following list indicates the pre-installed software associated with your system (depending upon your operating system).

■

Adobe Reader

■

EverNote (on select models)

■

Fujitsu Driver Update utility

■

Fujitsu HotKey

■

Google Desktop

■

Google Tool Bar

■

LifeBook Application Panel

■

Microsoft Works 8.5 Trial Edition (on select models)

■

Microsoft Office Home and Student 2007 Edition (on select Windows Vista Home Premium models)

■

Microsoft Office Small Business 2007 Edition (on select Vista Business models)

■

Microsoft Office 2003 Small Business Trial Edition (on Microsoft Windows XP Professional models)

■

OmniPass Fingerprint Recognition Utility

■

Symantec Norton Internet Security 2007 (90-day free trial) on Windows Vista models, and version 2006 on

Windows XP Pro. The following software is not pre-installed, but is located on the software CD that came with your system (as noted):

■

CyberLink MakeDisc (Windows Vista models)

■

MakeDVD (Windows XP Pro models)

■

CyberLink PowerProducer

■

CyberLink PowerDVD

■

Roxio Easy Media Creator (on select models)

LEARNING ABOUT YOUR SOFTWARE

Tutorials

All operating systems and most application software have tutorials built into them. We recommend that you step through the tutorial before you use an application.

Manuals

Included with your notebook you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included, are available online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications.

Acrobat Reader

Adobe

The Adobe Acrobat Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms.

CyberLink PowerDVD

PowerDVD from CyberLink is a versatile DVD player software application. PowerDVD provides high-quality video and audio playback on your system.

EverNote

EverNote allows you to easily capture, store and access a variety of documents, such as typed and handwritten memos, webpage excerpts, emails, phone messages, addresses, passwords, sketches, and documents.

Fujitsu Driver Update Utility

The Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. (See Automatically Down-

loading Driver Updates on page 59 for more information)

Fujitsu HotKey

Fujitsu HotKey allows you to control the display brightness of your notebook in order to maximize battery life.

Google Desktop

Google Desktop lets you to search the contents of your computer for emails, web history, and files. It also allows you to view news and photos from anywhere on your desktop.

Google Toolbar

Google Toolbar lets you to search the Internet quickly, block pop-ups, and perform a variety of other tasks to make your Internet experience easier and more pleasant.

LifeBook Application Panel Software

Your LifeBook is pre-installed with software utilities that let you operate and configure your LifeBook Application Panel. The Application Panel utilities are found under Start -> Settings -> Control Panel -> Application Panel.

Quicken New User Edition

(Windows XP Pro models only) Quicken New User Edition by Intuit is a personal money management program. It has features such as portfolio management, account registries, on-line banking and bill paying. Full version upgrade information is available on line.

OmniPass Fingerprint Recognition Software

The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass lets you use a "master password" for all Windows, applications, and on-line passwords, and presents a convenient user interface through which you can securely manage passwords, users, and multiple identities for each user.

Norton Internet Security™ from Symantec

Your system is pre-installed with a free 90-day trial version of Symantec’s Norton Internet Security™. Internet Security is designed to protect your notebook from computer viruses. It assists in protection of the data currently on your hard disk from contamination or destruction. The trial version is activated upon acceptance of software license agreement. After 90 days, you must purchase a subscription from Symantec to download the latest definitions. (See online help or manual for

more information on how and when to run this program)

LifeBook N6400 Series User’s Guide

Operating System Options

Depending upon your system, one of the following operating system configurations will be installed:

Microsoft Windows XP Professional Edition

With Microsoft Works 8.5 and Microsoft Office 60day trial (Small Business Edition 2003)

Microsoft Windows Vista Home Premium Edition

With Microsoft Works 8.5 and Microsoft Office (Home and Student Edition 2007)

Microsoft Windows Vista Business Edition

With Microsoft Works 8.5 and Microsoft Office 60day trial (Small Business Edition 2007)

■

Microsoft Works 8.5

Microsoft Works 8.5 is a software suite containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory.

■

Microsoft Office Home and Student Edition 2007

(Optional with Microsoft Windows Vista Home Premium Edition) Microsoft Office Home and Student 2007 is easy-to-use software to make you more productive in a home and/or school environment. Microsoft Office Home and Student 2007 includes Microsoft Word, Excel, PowerPoint, and OneNote.

■

Office Microsoft Small Business Edition 2007

(Optional with Microsoft Windows Vista Business

Edition) Microsoft Office 2007 Small Business Edition is easy-to-use software to help you manage business opportunities more effectively, create marketing materials, manage e-mail, and share information. Microsoft SBE includes Microsoft Word, Excel, Outlook, PowerPoint, Publisher, and Business Contact Manager.

Glossary

LifeBook N6400 Series User’s Guide

Glossary

AC Adapter

A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook.

Active-Matrix Display

A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.

BIOS

Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook notebook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.

Bit

An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).

bps

An abbreviation for bits per second. Used to describe data transfer rates.

Boot

To start-up a computer and load its operating system from disk, ROM or other storage media into RAM.

Bus

An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook.

Byte

8 bits of parallel binary information.

Command

An instruction which you give your operating system. Example: run a particular application or format a floppy disk.

Configuration

The combination of hardware and software that makes up your system and how it is allocated for use.

CRT

Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam.

Data

The information a system stores and processes.

Direct current. A voltage or current that does not fluctuate periodically with time.

DDR

Double Data Rate

Fast version of SDRAM that provides twice the bandwidth of standard SDRAMs.

Default Value

A pre-programmed value to be used if you fail to set your own.

DIMM

Dual-in-line memory module.

DISE

Drive Image Special Edition (DISE) by PowerQuest. Provides a way to restore your computer if you experience a hard disk crash or other system failure. DISE is used to restore the factory image and restore the system to its original state.

Cache Memory

A block of memory built into the microprocessor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.

CardBus

A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.

Disk

A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.

Disk Drive

The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.

Diskette

A floppy disk in a hard housing with a shutter.

LifeBook N6400 Series User’s Guide

DMA

Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.

DOS

Disk Operating System (MS-DOS is a Microsoft Disk Operating System).

Driver

A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.

DVD

Digital Video Disc. This is a form of optical disc storage for video, audio and computer data, envisioned to replace current digital storage formats (CD-ROM, laser and audio CD) because of its capability for storing greater amounts of data. A typical single layer, singlesided DVD, for example, can contain 4.7GB of data and a maximum of 17GB for the double-sided discs.

ECP

Extended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices.

ESD

Electrostatic Discharge. The sudden discharge of electricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.

Extended Memory

All memory more than the 640KB recognized by MS-DOS as system memory.

FCC

Federal Communication Commission.

Floppy Disk

A spinning platter of magnetic data storage media which is highly flexible.

Hexadecimal

A decimal notation for the value of a 4 bit binary number. (0-9, A, B, C, D, E, F) Example: 2F in hexadecimal = 00101111 in binary = 47 in decimal.

I/O

Input/Output. Data entering and leaving your LifeBook notebook in electronic form.

I/O Port

The connector and associated control circuits for data entering and leaving your LifeBook notebook in electronic form.

IDE

Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.

IEEE 1394

A type of data transfer protocol that allows for fast transfer of digital files and data with devices such as digital cameras.

IRQ

Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.

Kilobyte.

LAN

Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.

LCD

Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.

Lithium ion Battery

A type of rechargeable battery which has a high powertime life for its size and is not subject to the memory effect as Nickel Cadmium batteries.

Gigabyte.

Hard drive

A spinning platter of magnetic data storage media where the platter is very stiff.

Megabyte.

Megahertz

1,000,000 cycles per second.

Glossary

Memory

A repository for data and applications which is readily accessible to your LifeBook notebook’s CPU.

MHz

Megahertz.

MIDI

Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers.

Modem

A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.

Monaural

A system using one channel to process sound from all sources.

MVA

Multi-Domain Vertical Alignment. A display technology that allows a wider viewing angle than traditional displays, similar to a CRT.

organization that sets standards for add-in cards for personal computers.

Peripheral Device

A piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.

Pitch (keyboard)

The distance between the centers of the letter keys of a keyboard.

Pixel

The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.

POST

Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your LifeBook notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded.

NTSC

National TV Standards Commission. The standard for TV broadcast and reception for the USA.

Operating System

A group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of microprocessor in order to produce the desired results from that particular equipment.

Parallel Port

A connection to another device through which data is transferred as a block of bits simultaneously with a wire for each bit in the block and with other wires only for control of the device not for transfer of data.

Partition

A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.

PCMCIA

PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an

Program

An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.

RAM

Random Access Memory. A hardware component of your LifeBook notebook that holds binary information (both program and data) as long as it has the proper power applied to it.

RAM Module

A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.

Reset

The act of reloading the operating system. A reset erases all information stored in RAM.

Restart

See Reset.

Resume

To proceed after interruption. In your LifeBook notebook this refers to returning to active operation after having been in one of the suspension states.

LifeBook N6400 Series User’s Guide

ROM

Read Only Memory. A form of memory in which information is stored by physically altering the material. Data stored in this way can not be changed by your LifeBook notebook and does not require power to maintain it.

SDRAM

Synchronous Dynamic Random Access Memory.

Serial Port

A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.

Smart Card

Smart Cards are the same size and shape as credit cards, but they contain an integrated microprocessor chip. The chip can hold a variety of different information, and provides the user with many possible options, such as allowing them to make secure purchases, pay for phone calls, store security information, and provide personal identification and information.

SPDIF

Sony Philips Digital Interface Format. The optical digital audio format that allows you to download digital audio onto a MiniDisc recorder or connect to your sound system to play MP3 files with high fidelity sound.

SRAM

Static Random Access Memory. A specific technology of making RAM which does not require periodic data refreshing.

Status Indicator

A display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard.

Stereo (audio)

A system using two channels to process sound from two different sources.

S-Video

Super Video. A component video system for driving a TV or computer monitor.

System Clock

An oscillator of fixed precise frequency which synchronizes the operation of the system and is counted to provide time of day and date.

TFT

Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.

Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices.

VGA

Video Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of personal computers.

VRAM

Video Random Access Memory. A memory dedicated to video display data and control.

WFM

Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership(TCO) of business computing without sacrificing power and flexibility.

Write Protect

Prevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or directory of floppy diskette or hard drive.

XGA

Extended VGA.

Stroke (keyboard)

The amount of travel of a key when it is pressed from resting to fully depressed.

Suspend

To make inoperative for a period of time. Your LifeBook notebook uses various suspension states to reduce power consumption and prolong the charge of your battery.

SVGA

Super VGA.

Regulatory Information

NOTICE

Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.

FCC NOTICES Notice to Users of Radios and Television

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■

Reorient or relocate the receiving antenna.

■

Increase the separation between the equipment and receiver.

■

Connect the equipment into an outlet that is on a different circuit than the receiver.

■

Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device.

Notice to Users of the US Telephone Network

This equipment (Agere Systems, Inc. Modem model AM2) complies with Part 68 of FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this information or number must be provided to the telephone company.

This equipment is designed to be connected to the telephone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.

The ringer equivalent number (REN) of this equipment is 0.1B. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 00 is a REN of

0.0). For earlier products, the REN is separately shown on the label.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information).

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equipment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent, and an identification of the business or other entity, or other individual sending the message and the

LifeBook N6400 Series User’s Guide

telephone number of the sending machine or such business, other entity, or individual.

DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television

This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.

CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.

Notice to Users of the Canadian Telephone Network

NOTICE: This equipment (Agere Systems, Inc. Modem model AM2) meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.

Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.

For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician. This may be particularly important in rural areas.

Avis Aux Utilisateurs Du Réseau Téléphonique Canadien

AVIS: Le présent matériel (Agere Systems, Inc. Modem model AM2) est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal. Cette conformité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel.

Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.

Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.

AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.1B. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équiva-

lence de la sonnerie de tous les dispositifs n’excède pas 5.

Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont connectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connexions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales.

Appendix A

Integrated Wireless LAN* User’s Guide

*Optional Device

LifeBook N6400 Series User’s Guide

WIreless LAN User’s Guide

FCC REGULATORY INFORMATION

Please note the following regulatory information related to the optional wireless LAN device.

Regulatory Notes and Statements

Wireless LAN, Health and Authorization for use

Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:

• On board an airplane, or

• In an explosive environment, or

• In situations where the interference risk to other devices or services is perceived or identified as harmful.

In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment.

Regulatory Information/Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines.

Federal Communications Commission statement

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.

For operation within 5.15 ~ 5.25 GHz frequency range, it is restricted to indoor environments, and the antenna of this device must be integral.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with

the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the distance between the equipment and the receiver.

3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.

4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure statement

This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant with the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation is minimized. When using this device, a certain separation distance between antenna and nearby persons must be maintained to ensure RF exposure compliance. In order to comply with RF exposure limits established in the ANSI C95.1 standards, the distance between the antennas and the user should not be less than 20 cm (8 inches).

Export restrictions

This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment.

Canadian Notice

The device for the 5150-5250 MHz band is only for indoor usage to reduce the potential for harmful interference to cochannel mobile satellite systems.

The maximum antenna gain of 6 dBi permitted (for devices in the 5250-5350 MHz and 5470-5725 MHz bands) to comply with the e.i.r.p. limit.

In addition, users are cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz bands and these radars could cause interference and/or damage to LELAN devices.

LifeBook N6400 Series User’s Guide

Before Using the Wireless LAN

This manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual to ensure correct operation. Keep the manual in a safe place for future reference.

Wireless LAN Devices Covered by this Document

This document is applicable to systems containing the Intel PRO/Wireless WM3B3945ABG Network Connections (802.11a+b/g)

Characteristics of the WLAN Device

■

The WLAN device is a Mini-PCI card attached to the main board of the mobile computer.

■

The WLAN device operates in license-free RF bands, eliminating the need to procure an FCC operating license. The WLAN operates in the 2.4GHz Industrial, Scientific, and Medical (ISM) RF band and the lower, middle, and upper bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands.

■

The Intel PRO/Wireless 3945ABG WLAN device is capable of three operating modes, IEEE802.11a, IEEE802.11b and IEEE802.11g.

■

Encoding of data is modulated using Direct Sequence Spread Spectrum (DSSS) and Complementary Code Keying (CCK) when the WLAN device is operating in IEEE 802.11b mode and Orthogonal Frequency Division Multiplexing (OFDM) when operating in IEEE802.11a or IEEE802.11g mode.

■

The WLAN device is Wi-Fi certified and operates at the maximum data transfer rate of 54 Mbps in IEEE802.11a or IEEE802.11g mode and 11 Mbps in IEEE802.11b mode.

■

The WLAN device supports the following encryption methods - WEP, TKIP, CKIP, and AES encryption.

WIRELESS LAN MODES USING THIS DEVICE

Ad Hoc Mode

(See Figure A-1) "Ad Hoc Mode" refers to a wireless network where wireless network connectivity between multiple computers is established without a central network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers.

Ad Hoc mode requires that the SSID (service set identifier), network authentication, and encryption key settings are identically configured on all computers in the Ad Hoc network.

Access Point (Infrastructure) Mode

(See Figure A-2) Infrastructure mode refers to a wireless network in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the wired LAN in order to access computers, devices, and services such as file servers, printers, and databases.

How to Handle This Device

The WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Operating System that your mobile computer comes with has been pre-configured to support the WLAN device.

Figure A-1. Ad Hoc Mode Network

WIreless LAN User’s Guide

WIRELESS NETWORK CONSIDERATIONS

■

The WLAN supports IEEE802.11a/b/g and operates in the 2.4GHz ISM band and the 5 GHz UNII bands.

■

Microwave ovens will interfere with the operation of WLAN device as microwave ovens operate in the same

2.4GHz frequency range that IEEE802.11b/g devices operate in. Interference by microwaves does not occur with radio which operates in the 5 GHz RF band.

■

Wireless devices that transmit in the 2.4 GHz frequency range may interfere with operation of WLAN devices in IEEE802.11b/g modes. Symptoms of interference include reduced throughput and large amounts of frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure the proper operation of the WLAN device.

DEACTIVATING THE WLAN DEVICE

Deactivation of the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). Fujitsu mobile computers employ two methods with which to deactivate the WLAN device:

■

Using the Wireless On/Off Switch, or,

■

In Windows Vista, using the WLAN icon in the taskbar.

■

In Windows XP, using the Intel PROSet Software.

Deactivation using the Wireless On/Off Switch

The WLAN device can be deactivated quickly and efficiently by toggling the Wireless On/Off Switch to the Off position. (Figure A-3)

The wireless On/Off switch has no effect on non-Wireless LAN models.

Windows Vista: Deactivation using the icon in the taskbar

1. Right-click the WLAN icon in the taskbar at the bottom right of your screen.

Choose Disconnect from a network.

Deactivation using Intel PROSet for Wireless Utility

The WLAN device can be deactivated in Windows using the Intel PROSet for Wireless utility. The procedure to accomplish this:

1. Click [Start]-> [All Programs].

2. Select Intel ProSet Wireless, then click on Intel ProSet Wireless from the menu that appears. The Intel ProSet Wireless utility will be displayed.

3. At the bottom left corner of the window, select Wireless Off from the dropdown list.

ACTIVATING THE WLAN DEVICE

Activation of the WLAN device can be accomplished using the same methods as the deactivation process

■

Using the Wireless On/Off Switch

■

In Windows XP using Intel PROSet for Wireless utility

■

In Windows Vista, by right-clicking the WLAN icon then clicking “Connect to a network”

Volume

WLAN Switch

Figure A-3. Wireless LAN On/Off Switch Location

Figure A-2. Access Point (Infrastructure) Mode Network

ADSL modem,

Internet

cable modem, or similar

Wireless LAN

Wired LAN

Access Point*

*An optional hub for a wired LAN may be required depending upon the type of access point used.

LifeBook N6400 Series User’s Guide

Configuration of the WLAN Device

The WLAN device can be configured to establish wireless network connectivity using the Intel PROSet for Wireless utility (Windows XP models) or the WLAN utility that is built in (Windows Vista models). The Intel PROSet for Wireless utility allows for multiple profile setup and supports automatic profile switching. Support for most industry standard security solutions is contained in this software.

There are two procedures outlines below. The first one is for use with the Windows Vista operating system, and the other is used with the Windows XP operating system.

CONFIGURING THE WLAN WITH WINDOWS VISTA

The WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows Vista. Support for most industry standard security solutions is contained in this software.

Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters:

1. Click the Start button, then select Control Panel.

2. If the Control Panel is not in Classic View, select Classic View from the left panel. Double-click the Network and Sharing Center icon.

3. Select “Manage wireless networks” from the left panel.

4. Click on the [Add] button.

5. Depending upon what type of connection you would like to make, make a selection. For an infrastructure network, select “Manually create a network profile. For ad hoc network, select “Create an ad hoc network”.

2. Select “connect to a network”.

Select a network from the list that appears, and click the [Connect] button.

CONFIGURATION USING INTEL PROSET FOR WIRELESS UTILITY

This section explains the procedure to properly configure the WLAN device using the Intel PROSet for Wireless utility. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters:

Network Name - Also known as the SSID

Network Key (WEP) - Required if using static WEP

keys.

Authentication Type - Open, Shared, WPA, WPA-PSK

Procedure

1. Activate the WLAN device using either the Wireless On/Off Switch or the Intel PROSet for Wireless utility.

2. Click the [Start] button first and then [All Programs].

3. Click the icon [Intel PROSet Wireless] to execute the Intel PROSet for Wireless utility.

4. Click the [Add] button. The General Settings dialog displays.

5. Enter a profile name in the Profile Name field.

6. Enter the network SSID, in the Network Name (SSID) field.

7. Click Infrastructure or Ad Hoc for the operating mode.

8. Click [Advanced].

6. Enter the required information. It may be necessary to consult with your network administrator for some of the information.

7. In the event you require assistance, go to the Network and Sharing Center window (Start -> Control Panel -> Network and Sharing Center), and type in relevant keywords in the Search box.

Connecting to a Network with Windows Vista

After you have configured your computer, you can connect to an active network by performing the following steps:

1. Click on the WLAN icon in the system tray.

9. The Mandatory Access Point option is only used if Infrastructure mode is selected. Use this option to connect to a specific access point. Enter the MAC address for the access point. Click OK to save the setting and return to the General Settings page.

10. Click [Next].

11. If you wish to enable Cisco Compatible Extensions, click Cisco Options and check the “Enable Cisco Compatible Extensions” box.

12. To enable LEAP support, check the 802.1x option and choose LEAP from the pull-down list.

13. Click [OK].

Fujitsu N6420 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual