Fujitsu F2MC-8FX, F2MC Series, MB2146-401-03, MB2146-09, MB2146-303 Setup Manual

FUJITSU SEMICONDUCTOR
SUPPORT SYSTEM

SS01-26008-1E

F2MC Series

F2MC-8FX STARTER KIT (ver. 5V)

MB2146-401-03

SETUP GUIDE

PREFACE

Thank you for purchasing the F2MC * Series F2MC-8FX Starter Kit (ver. 5V) (Model : MB2146-401­03, referred to as "Starter Kit" in this manual).
This product is a starter kit for F2MC-8FX MB95FV100-103 ( ver. 5V), which comes with MB2 146-

2

MC Series BGM Adapter, referred to as "BGM Adapter"), MB2146-303 (F2MC-8FX Family

09 (F
MCU Board for MB95FV100-103 , referred to as "MCU Boar d"), MB2146-401 (F
Evaluatio n Board, r eferred to as "Evaluation Board"), and F
sional Pack.
This manual explains how to use the St arter Kit. Be sure to read this man ual before using the product.
For mass production/evaluation MCUs for this product, consult our Sales or Support representatives.

* : F2MC is the abbreviation used for FUJITSU Flexible Microcontroller.

■ Handling and use

Handling and use of this product and notes regarding its safe use are described in the manuals for
products bundled with the Starter Kit.
Follow the instructions in the manuals to use this product.
Keep this manual at hand so that you can refer to it anytime during use of this product.

■ Caution of the products described in this document

The following precautions apply to the product described in this manual.

2

2

MC-8L/8FX Family SOFTUNE Profes-

MC-8FX Family

WARNING

Electric shock,

Damage

Electric shock,

Damage

Indicates a potentially hazardous situation which, if not avoided appropriately,
could result in death or serious injury and/or a fault in the user’s system.

Before performing any operation described in this manual, turn off all the power
supplies to the system. Performing such an operation with the power on may
cause an electric shock or device fault.

Once the product has been turned on, do not touch any metal part of it.
Doing so may cause an electric shock or device fault.

CAUTION

Cuts, Damage

Cuts

Indicates a potentially hazardous situation which, if not avoided appropriately, may
result in minor or moderate injury and/or damage to the product or the equipment
to which the product is connected, to software resources such as data, or to other
properties.

Before moving the product, be sure to turn off all the power supplies and unplug the
cables. Watch your steps when carrying the product. Do not use the product at an
unstable location such as a place exposed to strong vibration or a sloping surface.
Doing so may let the product fall, resulting in an injury or fault.

The product has some sharp-pointed or edged parts inevitably exposed, such as
jumper plugs. Use meticulous care in handling the product not to get injured with
such pointed parts.

Damage

Damage

Damage

Damage

Damage

Damage

Neither put anything on or apply shock to the product. Once the product has been
powered, do not carry it. Doing either may cause a fault due to a load or shock.

Since the product contains many electronic components, keep it away from direct
sunlight, high temperature, and high humidity to prevent condensation. Do not use
or store the product where it is exposed to much dust or a strong magnetic or elec
tric field for an extended period of time.
An adverse operating or storage environment can cause a fault.

Use the product within the ranges of its general specifications.
Please see the item of "Specification" that has been described to the manual of
each product for the range of the specification.
Operating it outside the range of any general specification may cause a fault.

To prevent electrostatic breakdown, do not let your finger or an object touch any
metal part of the connector. Before handling the product, touch a metal object (such
as a door knob) to discharge static electricity from your body.

When turning the power on or off, follow the relevant procedure described in this
document. Before turning the power on, in particular, be sure to finish making all the
required connections. To set up and use the product, follow the instructions given
in this document.
Using the product incorrectly or inappropriately may cause a fault.

Before plugging or unplugging any cable for this product, be sure to turn the power
supply off. When unplugging the cable, remove it while holding the connector with
out pulling the cable itself. Pulling the cable itself or bending it may expose or dis­connect the cable core, resulting in a fault.

-

-

Damage

Damage

Although the MCU socket is structured not to accept an evaluation MCU in a wrong
orientation or position, pay due attention to the mounting orientation when mounting
the evaluation MCU. Forcing the evaluation MCU to be inserted in a wrong orienta
tion can damage the pins of the evaluation MCU and the accidental insertion pre­vention mechanism of the socket, resulting in a fault.

When stored, the product should be kept in its packaging box as it has no housing.
Re-transporting the product may damage it to cause a fault. Keep the packaging
materials used for shipment of the product and use them when re-transporting it.

-

• The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales representatives before ordering.

• The information, such as descri ptions of function an d application circuit examples, in this document are presented sole­ly for the purpose of reference to show examples of op erations an d uses of FUJITS U semi conducto r devi ce; FUJITSU
does not warrant proper operation of the device with respect to use based on such information. When you develop
equipment incorporating the device based on such information, you must assume any responsibility arising out of such
use of the information. FUJITSU assumes no liab ility for any damages whatsoever arising out of the use of the infor­mation.

• Any information in this document, including descriptions of function and schematic diagrams, shall not be construed
as license of the use or exercise of any intellectual property right, such a s pa ten t ri ght or c op yri gh t , or any o the r ri gh t
of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party’s intellectual property
right or other right by using such information. FUJITS U assumes no liabil ity for any infringeme nt of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.

• The products described in this document are designed, developed and manufactured as contemplated for general use,
including without limitation, ordinary industr ial use, genera l office use, personal u se, and household use, b ut are not
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damag e or other loss (i.e., nu clear reac tion control in nuclear facility, aircraft flight control, air
traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2)
for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in
connection with above-mentioned uses of the products.

• Any semiconductor devices have an inherent chance of failure. You must protect agains t injury, da mage or loss from
such failures by incorporating safety design measures into y our facility and equ ipment such as redundan cy, fire pro­tection, and prevention of over-current levels and other abnormal operating conditions.

• If any products described in th is document represen t goods or techno logies subjec t to certain restricti ons on export un­der the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be
required for e x por t of th os e pro du c ts fr om J a pan .

©2005 FUJITSU LIMITED Printed in Japan

www

Contents

1. Checking the Delivered Product ........................................................................1

2. Handling Precautions........................................................................................ 1

3. Feature... .. .............. .. ............. .. .............. .. ............. .. .............. .. ............. .. ............ 2

4. Hardware Setu p ............. ............. .. ............. .. .............. .. ............. .. .............. .. ......2

4.1 Configuration of each product............................................................................................... 3

4.2 Connection of each product ...................................................................................................5

5. Software Setup.................................................................................................. 9

5.1 Installation of software.......................................................................................................... 9

5.2 Operation of S

OFTUNE

...........................................................................................................13

iii

1. Checking the Delivered Product

Host machine This version is limited to 45 days

Before using the product, make sure that the following components are included:

MB2146-09

F2MC-8L/8FX Family

Professional Pack

S

OFTUNE

Trial Version

(S

OFTUNE

USB Cable Connector

(BGM Adapter enclosure)

MB2146-09

(BGM Adapter)

MB95FV100-103

(mounting at the MCU Board back )

MB2146-303
(MCU Board)

• MB2146-09

• MB2146-303

• MB2146-401

2

MC-8L/8FX Family : 1

• F
S

OFTUNE

*1

*2

*3

Professional Pack Trial Version *

4

• Setup Guide (Japanese version) : 1

• Setup Guide (English version, this manual) : 1

The inside of a dashed line is the package

of this product.

)

MB2146-401

(Evaluation Board)

: 1
: 1
: 1

*1 : To use the BGM Adapter, connect it to the host machine and USB cable. The USB cable is

enclosed by the BGM Adapter.

*2 : MB95FV100-103 is implemented in the MCU Board.

To use the MCU Board, connect it to the BGM Adapter and the Evaluation Board.

*3 : To use the Evaluation Board, connect it to the MCU Board. AC Adapter is enclosed by the

evaluation board

*4 : To use the S

, install it in your host machine.

OFTUNE

The duration of this version is limited to 45 days.

MB2146-401-01 is used as a starter kit for F2MC-8FX MB95FV100-103 (ver. 5V) by combining
with the bundled products.
For details about this product, consult our Sales or Support representatives.

2. Handling Precautions

The Starter Kit can be used in connection with its bundled products. To ensure correct use of this
product in a proper environment, observe the following guideline:

• Follow the instructions described in each manual for the bundled product to use this product.

1

3. Feature

The F2MC-8FX starter kit is the best for a performance and functional evaluation, and a check of
operation before including F
header board, continuation use also of the evaluation with a user's system can be carried out.
Below, the feature of the BGM debugger for F2MC-8FX is shown.

4. Hardware Setup

In the hardware setup procedure, you configure an d connect t he hardware pro ducts. Thi s chapter in­cludes the configuring and connecting procedure for each product in order. Check the contents and
complete the hardware setup.

2

MC-8FX in a user's system.By carrying out add iti on al purchase of the

• Microcomputer operation voltage It corresponds to +2.7V to +5.5V.

(The maximum and minimum of m icrocomputer oper ation voltage and freq uency of operatio n

differs with each MCU. refer to the documents (a data sheet, hardware manual, etc.) of each
device relation for th e frequency of MCU of operation.)

• Compact development environment, a light and small BGM Adapter.

• Since a monitor program is performed in exclusive memory space, it does not consume user

memory space.

• Continuation execution, step execution, a command b reak, a data br eak, sequ ential break cor
respondence

• Command trace is possible (a maximum of 16 branches).

• It connects with a host machine by the USB interface.

-

• Configuration of each product

- Configuring MCU Board

- Configuring Evaluation Board

• Connection of each product

- Connecting MCU Board and Evaluation Board

- Connecting BGM Adapter

- Connecting oscillators

- Connecting AC Adapter

2

4.1 Configuration of each product

This section describes how to configure the MCU Board and the Evaluation Board.

■ Configuring MCU Board

Set the following switches on the MCU Board, referring to "Figure 1 MCU Boar d Configuration".

2

3

GNDVCC

LVD1

LVD4

LVD3

LVD0

LVD2

8

9

7

A

6

B

5

C

4

D

3

E

2

F

1

0

CLK

CLK S.V.

APB8CX0X1X0A

PRODUCT SELECT

5

SUB CLOCK

BGM

ADAPTER

7

ON ON

1 2 3 4 1 2 3 4

C B A

1

4

3V5V

LVD2OFFLVD1

X1A

1

2

MAIN CLOCK

6

LVD2 detection voltage selection jumper plug

➀

Set the value to "LVD0".
Voltage selector swi tch

➁

Set the value to "5V".
Product selector switch

➂

Rotate the center tab to position the pointer for the corresponding number:
For 100-pin package, set the value to "0".
For 80-pin package, set the value to "1".
For 64-pin package, set the value to "2".
For 48-pin package, set the value to "3".
For none of the above, check on the settings in the MCU Board manual.

LVD selector switch

➃

Set the value to "OFF".
Miscellaneous switches

➄

Set "C" to "ON".
Set "CLK" to "OFF" if you use subclock, or "ON" if you don’t.
Set the other switches to "OFF" (to the side of numeral letters).

Clock input selector switch

➅

Set all to "OFF" (to the side of numeral letters)".
Subclock selector jumper plug

➆

Set all the values to the side of "B-C".

Figure 1 MCU Board Configuration

3

■ Configuring Evaluation Board

Set the following switches on the Evaluation Board, referring to "Figure 2 Evaluation Board Con­figurarion".

SW1

JP1

JP2

CN4

5V/3.3V Power supply selector jumper plug

➀

Set the value to the side of "+5V".
Analog power supply jumper plug

➁

Insert jumper plug for all the switches.
MOD selector jumper plug

➂

Insert jumper plug.

2

JP7

JP8

JP6 JP5

1

2

CN2

119

120

+3.3V

JP3 JP4

+5V

CN3

1

2

CN1

119

120

1

SW2

PJ1

3

Figure 2 Evaluation Board Configuration

4

4.2 Connection of each product

This section describes how to co nnect the MCU Board, the Evaluation Board, and the BGM Adapter .
This section also describes how to mount the crystal oscillator on the MCU Board, and how to plug
the AC adapter into the Evaluation Board.

■ Connecting MCU Board and Evaluation Board

Connect the MCU Board and the Eva luation Board, r eferring to "Fi gure 3 Connectio n of MCU
Board and Evaluation Board". Each board has an index to avoid the reve rse m oun ting. Lo ok at the
index position to connect the boards.

Evaluation Board

SW1

JP1

Index

CN4

JP2

(Backside mounting)

120

119

120

119

CN2

CN1

2

1

2

1

MCU Board

PJ1

SW2

(Backside mounting)

Figure 3 Connection of MCU Board and Evaluation Board

CN3

JP7

JP6 JP5

JP3 JP4

+5V

Index

+3.3V

5

■ Connecting BGM Adapter

Connect the BGM Adapter and the MCU Board, referring to "Figure 4 Connection of BGM Adapt ­er". The BGM Adapter and the MCU Bo ard h a ve an index mark (for pin 1) on it s connect o rs. Align
the index mark on both sides.
Plug a USB cable into the BGM Adapter (the cable is bundled with the BGM Adapter).

Make sure that POWER-SW on the Evaluation Board is set to OFF (to the side of " ") before plug­ging the cable.

Plug into BGM Adapter

USB cable

(Bundled with BGM Adapter)

MB2146-09

BGM Adapter

MCU Board

Index mark

Evaluation Board

JP2

CN4

PJ1

SW2

Power-SW

SW1

JP1

JP7

JP6 JP5

JP3 JP4

CN3

+3.3V

+5V

Figure 4 Connection of BGM Adapter

6

■ Connecting oscillators

Plug crystal/ceramic oscillators into the crystal oscillator mounting sockets (one for the main clock
and the other for the subclock) on the MCU Board (See "Figure 5 Connection of oscillators") .
You can see one crystal oscillator mounting socket for main clock and the other for subc lock on the
MCU Board. Mount a crystal or ceramic oscillator and a capacitor on the MCU Board.

GND

VCC

LVD4

LVD3

LVD1

LVD0

LVD2

8

9

7

A

6

B

5

C

4

D

3

E

2

F

1

0

CLK

CLK S.V.

APB8CX0X1X0A

PRODUCT SELECT

ADAPTER

ON ON

1 2 3 4 1 2 3 4

SUB CLOCK

BGM

C B A

2

Crystal oscillator mounting socket for main clock

➀

Mount a crystal oscillator used as "main clock".
Crystal oscillator mounting socket for subclock

➁

Mount a crystal oscillator used as "subclock".
If you disable the subclock, set the "CLK" switch to "ON".

3V5V

LVD2OFFLVD1

X1A

1

2

MAIN CLOCK

1

GND

Crystal oscillator mounting socket

Figure 5 Connection of oscillators

Capacitor mounting socketCapacitor mounting socket

Ceramic

oscillator

Crystal

oscillator

7

■ Connecting AC Adapter

Connect the AC Adapter and the Evaluation Board, referring t o "Figur e 6 Connection of AC Adapt­er". The AC Adapter (bundled with the Evaluation Board) is plugged into t he PJ1 on Evaluation
Board and the AC 100V Power Supply.

MB2146-09

Evaluation Board

CN4

JP2

JP1

CN3

+5V

JP7

JP6 JP5

JP3 JP4

SW1

+3.3V

BGM Adapter

Plug into Evaluation Board

Figure 6 Connection of AC Adapter

PJ1

SW2

AC Adapter

8

5. Software Setup

In the software setup procedure, you install and operate the software applications.
This chapter includes the installing and operating procedure for each software in order. Check the
contents and complete the software setup.

• Installation of software

- Installing S

- Installing USB driver

- Installing sample program

• Operation of S

- Starting S

- Starting Debugging

- Initializing MCU

- Running the program

- Aborting the program

- Ending Debugging

- Exiting S

5.1 Installation of software

This section describes how to install S
how to install the sample program.

OFTUNE

OFTUNE

OFTUNE

OFTUNE

Workbench

Workbench

OFTUNE

and the USB driver in your host machine, as well as

■ Installing S

OFTUNE

Follow the instruction described in "F2MC-8L/8FX Family 8-bit Microcontroller S
bench Installation Guide" to install S

■ Installing USB driver

Plug a USB cable connected to BGM Adapter into your host machine. After you connect the host
machine and the BGM Adapter, the [Found New Hardware Wizard] window appears. Follow the in
struction below to install the USB driver.

In a few seconds after the above dialog is displayed, the [Welcome to the Found New Hardware Wiz­ard] screen appears. Click [Next] to install the device driver.

OFTUNE

in your host machine.

OFTUNE

Work-

-

9

The [Install New Hardware Device Drivers] screen appears.
Click [Search for a suitable driver for my device (recommended)], and then click [Next] to search
for a suitable driver for your device.

The [Locate Driver Files] screen appears.
Check [Specify a location], and then click [Next] to specify the location for the driver.

10

A file location dialog appears.
Select "SiUSBdB.INF" in the "\Drivers" folder (under a directory where S
click [Open] to specify the driver.

OFTUNE

is installed), and

In the [Copy manufacturer’s files fro m] bo x, make sure t hat t he "\Dri vers" folder (und er a di rectory
where SOFTUNE

The [Driver Files Search Results] screen appears.
Click [Next] to start installing the driver.

is installed) is selected, and click [OK].

The [Completing the Found New Hardware Wizard] screen appears.
Now that the USB driver installation has completed, click [Finish] to exit the Wizard.

11

■ Installing sample program

Copy only a folder named "\fsg" und er "\MAN UAL\Fi rs tStepGu id e" in S
ple" folder under a directory where S

All the data in the "\fsg" folder is set to "read-only". Open th e folder’s properties, and deselect the
[Read Only] checkbox, and click [OK].

OFTUNE

is installed.

OFTUNE

CD into the "\sam-

In the [Confirm Attribute Change] dialog, check [Apply Changes to this folder, sub-folders, and
files], and click [OK] to confirm the attribute change.

Note : This software application uses the relo ad ti me r, so it c an not b e us ed in 4 8- pi n pa ck age or le ss , wh ich

does not implement the reload timer. When using this software, set 64-pin package or more in the prod
uct selector switch on MCU Board.

-

12

5.2 Operation of

This section describes how to start S

OFTUNE

S

OFTUNE

Workbench and operate it using the sample program.

■ Starting S

OFTUNE

Workbench

Start S
[Open Workspace].

OFTUNE

and configure the S

OFTUNE

development environment. From the [File] menu, click

In a file location dialog, select the "\sample\fsg\8fx_sample" folder under a directory where S
is installed, and specify "fsg_sample.wsp", then click [Open].

OFTUNE

13

Select and right-click "e mu_dbg.su p" under the "Debug" fol der, then cli ck [Change Set tings] t o start
the setup wizard.

14

The setup wizard is started. Click [Next].

In [Debug Type], specify [Emulator Debugger], and click [Next].

In [ICE Type], specify [MB2146-09], and click [Next].

15

In [Device Name], specify [USB], and click [Next].

In [Output Frequency], set the frequency of oscillator connected to MCU Board, and click [Next].

The [Batch file] setting is not required. Click [Next].

16

Check [Auto-load when starting debug], and specify "fsg_sample.prc" in [After] under [Specifica­tion batch file before/after load], then click [Next].

Check [Select All], and click [Next].

Click [Finish] to complete the setup of S

OFTUNE

development environment.

17

■ Starting Debugging

<Turning Evaluation Board on>

Before starting debugging, turn the Evaluation Board on. Push POWER-SW on the Board to ON (to
the side of " | ") to turn it on (See "Connecting BGM Adapter" for information about POWER-SW) .

After the Evaluation Board is turned on, click [Start debug] from the [Debug] menu to start debug­ging.
When you start debugging, the sample program is automatically loaded.

18

■ Initializing MCU

Initialize MCU. To do so, click the Reset button on the task bar.

Reset bu tton

19

■ Running the program

You can run the program by clicking the "execution-related buttons" on the task bar.
You can also set a breakpoint by clicking the " " mark in the Source window.

[Execution-related buttons]

[Go]

[Step In]
[Step Over]
[Step Out]
[Run Until Cursor]

Source window

20

Breakpoint

■ Aborting the program

After you have run the program, you can stop it by clicking the Abort button on the task bar.

Abort button

21

■ Ending Debugging

To end debugging, click [End debug] from the [Debug] menu.

<Turning Evaluation Board off>

After you have finished debugging, turn the Evaluation Board off for safety. Push POWER-SW on
the Board to OFF (to the side of "

tion about POWER-SW.)

") to turn it off. (See "Connecting BGM Adapter" for informa-

22

■ Exiting S

OFTUNE

Workbench

To exit S

OFTUNE

Workbench, click [Exit] from the [File] menu.

23

SS01-26008-1E

FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM

2

MC Series

F

2

F

MC-8FX STARTER KIT (ver. 5V)
MB2146-401-03
SETUP GUIDE

March 2005 the first edition
Published FUJITSU LIMITED Electronic Devices
Edited Business Promotion Dept.