Fujitsu LifeBook M2010 User Manual



User’s Guide

Learn how to use

your Fujitsu M2010 notebook

Fujitsu America, Inc. has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.

Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited.

Intel and Intel Atom are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Bluetooth is a trademark of Bluetooth SIG, Inc., USA.

ENERGY STAR and the ENERGY STAR certification mark are registered trademarks of the U. S. Government.

Google and Picasa are trademarks or registered trademarks of Google Incorporated.

ArcSoft WebCam Companion is a trademark of ArcSoft, Inc.

Adobe, Acrobat, and Acrobat Reader are either a registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

Norton and Norton Internet Security are trademarks or registered trademarks of Symantec Corporation in the United States and other countries.

All other trademarks mentioned herein are the property of their respective owners.

No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu. 

B6FJ-2081-01ENZ0-00

WARNING

HANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE

TATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

ASH HANDS AFTER HANDLING.

DECLARATION OF CONFORMITY

according to FCC Part 15

Responsible Party Name: Fujitsu America, Inc.

Address: 1250 E. Arques Avenue

Sunnyvale, CA 94085

Telephone: (408) 746-6000

Declares that product: Base Model Configuration:

Fujitsu M2010 notebook

Complies with Part 15 of the FCC Rules.

This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:

(1) This device may not cause harmful interference, (2) This device must accept any interference received,  including interference that may cause undesired operation.

IMPORTANT SAFETY INSTRUCTIONS

AC adapter output polarity:

This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 19 VDC, with a  minimum current of 3.16 A.

When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

• CAUTION - HOT SURFACE: The bottom of this notebook computer can become hot when used for long periods of time. When

using this notebook, take caution to limit long term or continuous use while resting it on exposed skin, such as the lap.

• Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a

swimming pool.

• Avoid using a modem during an electrical storm. There may be a remote risk of electric shock from lightning.

• Do not use a modem to report a gas leak in the vicinity of the leak.

• Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with

local codes for possible special disposal instructions.

• To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord.

• For TV tuner use: To protect from overvoltages and transients on the Cable Distribution System, make sure that the outer shield of

the coaxial cable is connected to earth (grounded) at the building premise as close to the point of cable entrance as practicable, as required per NEC Article 820.93, ANSI/NFPA 70: 2005. If you have questions about your CATV installation, contact your service provider.

SAVE THESE INSTRUCTIONS

For Authorized Repair Technicians Only

DANGER OF EXPLOSION IF LITHIUM (CLOCK) BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY

WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTION.

OR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH THE SAME TYPE AND

RATING FUSE.

Recycling your battery

Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*. If you replace it, it is important that you dispose of the old battery properly because batteries contain materials that could cause environmental damage if disposed of improperly.

Fujitsu is very concerned with environmental protection, and has enlisted the services of the Rechargeable Battery Recycling Corporation (RBRC)**, a non-profit public service organization dedicated to protecting our environment by recycling old batteries at no cost to you.

RBRC has drop-off points at tens of thousands of locations throughout the United States and Canada. To find the location nearest you, go to www.RBRC.org

If there are no convenient RBRC locations near you, you can also go to the EIA Consumer Education Initiative website (http://EIAE.org/) and search for a convenient disposal location.

Remember – protecting the environment is a cooperative effort, and you should make every effort to protect it for current and future generations.

* To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site at www.shopfujitsu.com in the US or

www.fujitsu.ca/products/notebooks in Canada.

** RBRC is an independent third party to which Fujitsu provides funding for battery recycling; RBRC is in no way affiliated with

Fujitsu.

or call 1-800-822-8837.

Contents

Preface

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 1 Getting to Know Your Notebook

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Locating the Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Front and Display Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Left-Side Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Right-Side Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Bottom Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Wireless Device Emission Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Hard Drive Access Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

CapsLock Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

NumLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Opening the Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Adjusting Display Panel Brightness . . . . . . . . .

Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Touchpad Pointing Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Clicking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Touchpad Control Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Volume Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Controlling the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Chapter 2 Getting Started with Your Notebook

Power Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Connecting the Power Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Starting Your M2010 Notebook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Booting the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Starting Windows XP the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Installing ClickMe!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Fujitsu Driver Update Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

. . . . . . . . . . . . . . . . . . . . . 30

Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Power/Suspend/Resume Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Standby Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Hibernation (Save-to-Disk) Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Windows Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Restarting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Powering Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

ENERGY STAR® Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Chapter 3 User-Installable Features

Lithium ion Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Recharging the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Removing Memory Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Installing a Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Checking the Memory Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Memory Stick/Secure Digital Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Inserting MS/SD Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Removing an MS/SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Internal LAN (RJ-45) jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Microphone Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

External Video Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Chapter 4 Troubleshooting Your Notebook

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Identifying the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Troubleshooting Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Power On Self Test Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Restoring Your Pre-installed Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Backing Up and Re-installing Individual Drivers and Applications . . . . . 77

Recovering Factory and System Images. . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Automatically Downloading Driver

Chapter 5 Care and Maintenance

Caring for your M2010 Notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Cleaning your notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Storing your notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Traveling with your notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Chapter 6 System Specifications

Updates . . . . . . . . . . . . . . . . . . . . . . . 78

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Mass Storage Device Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Popular Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Included Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Learning About Your Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Glossary/Regulatory

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Appendix A: WLAN User’s Guide

Before Using the Optional Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . 114

Wireless LAN Device Covered by this Document. . . . . . . . . . . . . . . . . . . 114

Characteristics of the WLAN Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Wireless LAN Modes Using this Device . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Deactivating the WLAN Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Disconnection Using the Icon in the Taskbar. . . . . . . . . . . . . . . . . . . . . . . 117

Activating the WLAN Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Configuring the Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Configuring the WLAN using Windows XP . . . . . . . . . . . . . . . . . . . . . . . 119

Connection to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Troubleshooting the WLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

WLAN Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Using the Bluetooth Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

What is Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Where to Find Information About Bluetooth . . . .

. . . . . . . . . . . . . . . . . . . 123

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Preface

About This Guide

The M2010 notebook from Fujitsu is a small yet powerful computer, perfect for networking. It is powered by an Intel Atom® processor and integrated Mobile Intel® 945 GSE Express chipset. The notebook has a built-in 10.1” wide SVGA color display with LED backlight.

This manual explains how to operate your M2010 notebook’s hardware and built-in system software. Your M2010 notebook comes with Windows® XP Home Edition pre-installed.

Conventions Used in the Guide

Keyboard and on-screen keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].

Pages with additional information about a specific topic are cross-referenced within the text. For example: (“See Installation Procedure on page 43”.) Note that all cross-references are linked to the referenced items, so by clicking the link, you will automatically go to the referenced item or page.

On-screen menu items appear in bold. Example: “Click Object Properties and select your choice”.

THE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF

THE SUBJECT MATERIAL.

THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR

COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATION CAREFULLY.

HE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR

NOTEBOOK, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.

Fujitsu Contact Information

Service and Support

You can contact Fujitsu Service and Support in the following ways:

• Toll free: 1-800-8Fujitsu (1-800-838-5487)

• Website: http://www.computers.us.fujitsu.com/support

Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:

• Product name

• Product configuration number

• Product serial number

• Purchase date

• Conditions under which the problem occurred

• Any error messages that have occurred

• Type of device connected, if any

- About This Guide

Fujitsu Shopping Online

You can go directly to the online by going to the website at: www.shopfujitsu.com.

YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS.

Limited Warranty

Your M2010 notebook is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your notebook for the Limited Warranty period and terms and conditions.

- About This Guide

Chapter 1

Getting to Know Your Notebook

Overview

This section describes the components of your Fujitsu M2010 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers.

Figure 1. Fujitsu M2010 notebook

Locating the Controls and Connectors

Connectors and peripheral interfaces on the M2010 notebook allow you to connect a variety of devices. Specific locations are illustrated in Figures 2 through 5. The table below provides a short description of each icon on the M2010 notebook. Each of the icons is either molded into or printed on the notebook chassis.

Connection Notebook

Purpose

Icon

DC in connector Connect an external power source such as the AC adapter or auto/airline

adapter.

Secure Digital/

emory Stick Pro

M (SD/MS) Slot

USB Ports Connect Universal Serial Bus 2.0 or 1.1 compliant devices to the 

Microphone Jack

Headphone Jack Connect stereo headphones or powered external speakers. The internal

Security lock slot The security slot allows you to secure the notebook using compatible

The Secure Digital/Memory Stic flash memory card for data storage. Flash memory cards allow you to transfer data to and from a variety of different digital devices.

notebook.

Connect an external microphone. The internal microphone is disabled whe

n you plug in an external microphone. The same icon is used for the

internal microphone.

eaker is disabled when you plug in external headphones or powered

sp speakers.

cking devices.

k (SD/MS) card slot allows you to install a

- Locating the Controls and Connectors

Connection Notebook

Icon

Purpose

Suspend/ Resume button

Local Area

ork (LAN)

Netw

Battery Release

tch

The Suspend/Resume button allows you to suspend notebook activity without powering off, resume your notebook from suspend mode, and power on the system when it has been shut down from Windows.

The LAN (RJ-45) jack is used to connect the internal 10/100 Base-T/Tx Et

hernet to a Local Area Network (LAN) in your office or home, or

broadband devices such as a cable modem, DSL, or satellite Internet.

The battery release latch allows you to remove the battery from your syst

em for storage or replacement.

- Locating the Controls and Connectors

Display Panel

Keyboard

Power/Suspend/ Resume Button

Touchpad Pointing Device

Built-in Microphone

Status Indicator Panel

1.3 Megapixel Web Camera

Status Indicator Panel

Stereo speaker

Figure 2. M2010 notebook with display open

- Locating the Controls and Connectors

Front and Display Components

The following is a brief description of your notebook’s front and display features.

Web Camera

The 1.3 megapixel web camera allows you to take pictures of yourself to send over the internet. For information on using the camera, see the documentation associated with the ArcSoft WebCam Companion application.

Display Panel

The display panel is a color LCD panel with back lighting for the display of text and graphics and touch screen functionality.

Suspend/Resume Button

The Suspend/Resume button allows you to suspend system activity without powering off, resume your system from standby mode, and power on your system when it has been shut down from the Windows operating system. See “Power On” on page 41.

Status Indicator Panel

There are two Status Indicator Panels that display symbols corresponding to specific components of your M2010 notebook. See “Status Indicator Panel” on page 26.

Keyboard

A full-function keyboard with dedicated Windows keys. See “Keyboard” on page 31.

Touchpad Pointing Device

The Touchpad pointing device is a mouse-like cursor control with a right button, a left button, and a cursor control pad. See “Touchpad Pointing Device” on page 34.

Stereo Speakers

The speakers allows you to listen to stereo sound from your system.

Built-in Microphone

The built-in microphone allows you to input mono audio.

- Locating the Controls and Connectors

DC Power Jack

Air Vents

External Video Port

USB 2.0 Port

Figure 3. M2010 notebook left-side panel

Left-Side Panel Components

The following is a brief description of your notebook’s left-side components.

DC Power Jack

The DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your system and charge the internal Lithium ion Battery.

Air Vents

The air vents allow proper air circulation to ensure that the system does not overheat.

TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE, BE SURE TO

KEEP ALL AIR ALL VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE

PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED.

O NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN

TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.

- Locating the Controls and Connectors

External Video Port

The external video port allows you to connect an external monitor or LCD projector. See “External Video Port” on page 63.

USB 2.0 Ports

The three USB 2.0 ports (one on the left side, two on the right side) allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480 Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 12 Mbps. See “Universal Serial Bus Ports” on page 62.

- Locating the Controls and Connectors

Microphone Jack

Headphone Jack

Secure Digital/Memory Stick Card Slot

USB 2.0 Ports

LAN (RJ-45) Jack

Anti-Theft Lock Slot

Figure 4. M2010 notebook right-side panel

Right-Side Panel Components

The following is a brief description of your notebook’s right-side components.

Secure Digital/Memory Stick Card Slot

The Secure Digital/Memory Stick (SD/MS) card slot allows you to insert a flash memory card for data storage. Flash memory cards allow you to transfer data to and from a variety of different digital devices.

Headphone Jack

The headphone jack allows you to connect stereo headphones or powered external speakers. See “Headphone Jack” on page 63.

Microphone Jack

The microphone jack allows you to connect an external mono microphone. See “Microphone Jack” on page 62.

- Locating the Controls and Connectors

USB 2.0 Ports

LAN (RJ-45) Port

The internal LAN (RJ-45) port is used for an internal 10/100 Base-Tx Ethernet. See “Internal LAN (RJ-

45) jack” on page 62.

Anti-theft Lock Slot

The anti-theft lock slot allows you to attach a optional physical lock-down device.

- Locating the Controls and Connectors

Memory

Lithium ion

Air Vents

Battery Latches

(various locations)

Stereo Speaker

Upgrade Compartment

Figure 5. M2010 notebook bottom panel

Bottom Components

The following is a brief description of your notebook’s bottom panel components.

Battery Latches

The battery latches are used to secure the Lithium ion battery in the battery bay.

- Locating the Controls and Connectors

Lithium ion Battery Bay

The battery compartment contains the Lithium ion battery. The battery should be removed when the computer is stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery. See “Lithium ion Battery” on page 51.

Memory Upgrade Compartment

Your notebook comes with high speed DDR2 Synchronous Dynamic RAM (SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your system, hence improving overall performance. See “Memory Upgrade Module” on page 56.

Air Vents

The air vents allow air to circulate through the system to cool down the components.

TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE, BE SURE TO

KEEP ALL AIR ALL VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED.

O NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN

TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.

- Locating the Controls and Connectors

Hard Drive Access

CapsLock NumLock

Power Indicator

Wireless Device Indicator

Battery Charge/ DC In

Figure 6. Status Indicator Panel

Status Indicator Panel

The status indicators display symbols that correspond to specific components of your notebook. (Figure 6) The symbols show how each of those components is operating. Note that there are two locations that contain status indicators: above the keyboard and on the front edge of the notebook.

Wireless Device Emission Indicator

The Wireless Device Emission indicator appears when the Wireless LAN or Bluetooth are emitting.

Power Indicator

The Power indicator symbol located on the power button shows whether your system is operational. When it is solid blue, it means that there is power to your computer and that it is ready for use.

Battery Charge/DC-In Indicator

Depending upon whether you have an AC adapter connected or not, the battery indicator will appear in a variety of colors and states.

AC Adapter connected...

Solid blue Charge complete

Solid orange Charging in process

Purple, blinking Battery malfunction

No AC Adapter connected...

Orange, blinking Battery is charged 12% or less.

Purple, blinking Battery malfunction

Off Battery charge between 13% and 100%

Battery completely discharged

No battery installed

Table 1. Battery indicator states

BATTERIES SUBJECTED TO SHOCKS, VIBRATION OR EXTREME TEMPERATURES CAN BE PERMANENTLY

DAMAGED.

Hard Drive Access Indicator

The Hard Drive Access indicator lights green when your internal hard drive is being accessed.

CapsLock Indicator

The CapsLock indicator shows that your keyboard is set to type in all capital letters.

NumLk Indicator

The NumLk indicator shows that the integral keyboard is set in ten-key numeric keypad mode.

Display Panel

Display Cover

Your Fujitsu notebook contains a display panel that is backlit for easier viewing in bright environments.

Figure 2. Opening the Display Panel

Opening the Display Panel

Lift the display backwards, being careful not to touch the screen with your fingers, until it is at a

comfortable viewing angle. (Figure 2)

- Display Panel

Adjusting Display Panel Brightness

Once you have turned on your system, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness: keyboard and power management utility.

NOTE THAT WHEN YOU CHANGE THE DISPLAY SETTINGS, THE CHANGES WILL BE RETAINED AFTER

SLEEP AND RESTART.

Using the Keyboard to Adjust Brightness

Use the following key combinations to adjust the screen brightness:

• [Fn+F6]: Pressing repeatedly will lower the brightness of your display.

• [Fn+F7]: Pressing repeatedly will increase the brightness of the display.

Using Power Management to Adjust Brightness

To adjust brightness with the power management utility, click Start > Control Panel (Classic View) > Brightness Control. Set the screen brightness slider for battery and AC power scenarios.

F USING AC POWER, YOUR BRIGHTNESS SETTING IS SET TO ITS HIGHEST LEVEL BY DEFAULT. IF USING

BATTERY POWER, YOUR BRIGHTNESS SETTING IS SET TO APPROXIMATELY MID-LEVEL BY DEFAULT.

HE HIGHER THE BRIGHTNESS LEVEL, THE MORE POWER THE NOTEBOOK WILL CONSUME AND THE FASTER YOUR BATTERIES WILL DISCHARGE. FOR MAXIMUM BATTERY LIFE, MAKE SURE THAT THE BRIGHTNESS IS SET AS LOW AS POSSIBLE.

- Display Panel

Keyboard

Fn Key

Start Key

Function Keys

Numeric Keypad

Application Key

Cursor Keys

(surrounded by heavy line)

Figure 3. Keyboard

Using the Keyboard

Your M2010 notebook has an integral 80-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys. (Figure 3)

• Numeric keypad: Your system allows certain keys to serve dual purposes, both as standard

characters and as numeric and mathematical keys. The ability to toggle between the standard character and numerical keys is controlled through the [NumLk] key.

- Keyboard

• Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to

the right, left, up, or down within windows, applications and documents.

• Function keys: The keys labeled [F1] through [F11/F12], are used to produce special actions that

vary depending on what program is running. They are also used in conjunction with the [Fn] key to perform certain tasks, as detailed below under “Function Keys”.

• Windows keys: These keys work with your Windows operating system and function the same as

the onscreen Start menu button, or the right button on your pointing device.

Numeric Keypad

Certain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] key. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary functions. (Figure 3)

Windows Keys

Your M2010 notebook has two Windows keys: a Start key and an Application key. The Start key displays the Start menu. This button functions the same as your onscreen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows documentation for additional information regarding the Windows keys.) (Figure 3)

Cursor Keys

The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right).

- Keyboard

Function Keys

Your notebook has 11 function keys, F1 through F11/F12. The functions assigned to these keys differ for each application.

• [Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.

• [Fn +F5]: Pressing [F5] while holding [Fn] allows you to toggle the wireless devices on and off.

• [Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.

Note that adjusting the brightness using the keyboard changes the system setting.

• [Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.

• [Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your system.

• [Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your system.

• [Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send

your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, external monitor only, and both built-in display panel and external monitor.

• [F11] / [Fn +F11]: Pressing [F11] alone will invoke whatever action is assigned to the [F11] key.

Pressing [F11] while holding [Fn] will invoke whatever action is assigned to the [F12] key.

- Keyboard

Touchpad Pointing Device

Left Button

Right Button

Cursor Control

Figure 4. Touchpad pointing device

The Touchpad pointing device comes built into your Fujitsu notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left button and a right button. The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger. The left and right buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending on the application that is being used.

- Touchpad Pointing Device

AN EXTERNAL MOUSE CAN BE CONNECTED TO THE USB PORTS ON YOUR NOTEBOOK AND USED

SIMULTANEOUSLY WITH THE TOUCHPAD. HOWEVER, IF YOU BOOT THE SYSTEM WITH AN EXTERNAL MOUSE CONNECTED THE TOUCHPAD WILL BE DISABLED OR ENABLED DEPENDING ON THE SPECIFICATIONS IN YOUR BIOS SETTINGS. See “BIOS Setup Utility” on page 42.

Clicking

Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the Touchpad once.

Figure 5. Clicking with button

- Touchpad Pointing Device

Figure 6. Clicking with Touchpad

Double-Clicking

Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and immediately release it. You can also perform the double-click operation by tapping lightly on the Touchpad twice.

Figure 7. Double-clicking with button

Figure 8. Double-clicking with Touchpad

- Touchpad Pointing Device

Dragging

Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap. Next, move the object to its new location by moving your finger across the Touchpad, and then release your finger.

Figure 9. Dragging

Touchpad Control Adjustment

The Windows Control Panel allows you to customize your Touchpad with selections made from within the Mouse Properties dialog box.

- Touchpad Pointing Device

Volume Control

Your Fujitsu notebook has multiple volume controls which interact with each other.

Controlling the Volume

The volume can be controlled in several different ways:

• Volume can be set from within the Volume Control in the Notification Area at the bottom right of

your screen.

• Volume can be controlled with the [F8] and [F9] functions keys. Pressing [F8] repeatedly while

holding [Fn] will decrease the volume of your notebook. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your notebook.

• Volume can be controlled by many volume controls that are set within individual applications.

• Certain external audio devices you might connect to your system may have hardware volume

controls.

ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF

YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF, YOU WILL OVERRIDE THE EXTERNAL VOLUME CONTROL SETTING.

Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources. We recommend that you experiment with the various volume controls to discover the optimal sound level.

- Volume Control

Chapter 2

DC Power Jack

AC Adapter

AC Cable

DC Output Cable

Getting Started with Your Notebook

Figure 10. Connecting the AC Adapter

Power Sources

Your Fujitsu notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.

Connecting the Power Adapters

The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries.

Connecting the AC Adapter

Plug the DC output cable into the DC power jack of your notebook.

1 2 Plug the AC adapter into an AC electrical outlet.

Connecting the Optional Auto/Airline Adapter

Plug the DC output cable into the DC power jack on your notebook.

1 2 Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key in the On or Access

3 Plug the Auto/Airline adapter into the DC power jack on an airplane seat.

Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power

Be sure that you have at least one charged battery installed.

2 Remove the AC adapter or the Auto/Airline adapter.

THE LITHIUM ION BATTERY IS NOT CHARGED UPON PURCHASE. INITIALLY, YOU WILL NEED TO CONNECT

EITHER THE AC ADAPTER OR THE AUTO/AIRLINE ADAPTER TO USE YOUR NOTEBOOK.

- Power Sources

Starting Your M2010 Notebook

Power On

Power/Suspend/Resume Button

The Power/Suspend/Resume button is used to turn on your notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your notebook.

WHEN YOU TURN ON YOUR NOTEBOOK BE SURE YOU HAVE A POWER SOURCE. THIS MEANS THAT AT

LEAST ONE BATTERY IS INSTALLED AND CHARGED, OR THAT THE AC OR AUTO/AIRLINE ADAPTER IS CONNECTED AND HAS POWER.

To turn on your notebook from its off state, press the Power/Suspend/Resume button, located above the keyboard to the right. When you are done working you can either leave your notebook in Suspend mode, See “Standby Mode” on page 47. or you can turn it off. See “Powering Off” on page 49..

O NOT CARRY YOUR NOTEBOOK AROUND WITH THE POWER ON OR SUBJECT IT TO SHOCKS OR

VIBRATION, AS YOU RISK DAMAGING YOUR NOTEBOOK.

When you power on your notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your notebook will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 74. Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.

After satisfactory completion of the POST, your notebook will load your operating system.

- Starting Your M2010 Notebook

NEVER TURN OFF YOUR NOTEBOOK DURING THE POWER ON SELF TEST (POST) OR IT WILL CAUSE AN

ERROR MESSAGE TO BE DISPLAYED WHEN YOU TURN YOUR NOTEBOOK ON THE NEXT TIME. See

“Power On Self Test Messages” on page 74.

Boot Sequence

The procedure for starting-up your notebook is termed the Bootup sequence and involves your notebook’s BIOS. When your notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook. This information is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is found. During booting, your notebook is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.

The boot sequence is executed when:

• You turn on the power to your notebook.

• You restart your notebook from the Windows Shut Down dialog box.

• The software initiates a system restart. Example: When you install a new application.

BIOS Setup Utility

The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your notebook.

The BIOS Setup Utility configures:

• Device control feature parameters, such as changing boot devices.

• System Data Security feature parameters, such as passwords.

- Starting Your M2010 Notebook

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following:

1 Turn on or restart your notebook. 2 To enter the BIOS Setup Utility, press the [F2] key once the Fujitsu logo appears on the screen. This will open

the main menu of the BIOS Setup Utility with the current settings displayed.

3 Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter

the current settings.

The Boot Menu can also be invoked by pressing the [F11] key when the Fujitsu logo appears on the screen.

Setting the Supervisor Password and Password on Boot Settings

Enter the BIOS Setup Utility.

2 Scroll to the Security Tab. 3 Select Set Supervisor Password, press [ENTER]. 4 Enter New Password and confirm new password. 5 In the Security Tab, scroll to Password on Boot, and press [ENTER]. 6 Press [F10]. The Save and Exit, a screen will pop up. If you are finished making changes, select Yes and press

[ENTER].

BIOS Guide

A guide to your notebook’s BIOS is available online. Please visit our service and support website at

http://www.computers.us.fujitsu.com/support, then select User’s Guides under Online Support. Select

your Product, Series, and Model, then click [Go]. Under the Manuals tab, select the BIOS Guide.

Booting the System

We strongly recommend that you not attach any external devices until you have gone through the initial power on sequence.

When you turn on your notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.

- Starting Your M2010 Notebook

Starting Windows XP the First Time

Registering with Microsoft

In order to ensure that you receive the most benefits from the Windows operating system, it should be registered the first time you use it.

After you receive the Windows Welcome screen, you will be prompted to enter registration information in the following order.

First of all, you will need to read and accept the End User License Agreements (EULAs). After accepting the EULAs, you will be asked if you want to enable the Automatic Updates feature. Acceptance of this feature is recommended because it allows your system to be updated automatically whenever an important change becomes available for your notebook.

• IF YOU REJECT THE TERMS OF THE LICENSE AGREEMENT YOU WILL BE ASKED TO REVIEW THE LICENSE

AGREEMENT FOR INFORMATION ON RETURNING WINDOWS OR TO SHUT DOWN YOUR NOTEBOOK.

• YOU CANNOT USE YOUR NOTEBOOK UNTIL YOU HAVE ACCEPTED THE LICENSE AGREEMENT. IF YOU STOP THE

PROCESS YOUR NOTEBOOK WILL RETURN TO THE BEGINNING OF THE WINDOWS WELCOME PROCESS, EVEN IF YOU SHUT YOUR NOTEBOOK DOWN AND START IT UP AGAIN.

Several additional windows will appear, prompting you to enter a name and description for your computer, an Administrator password, and a domain name. Read the instructions on the screens carefully and fill in the information as directed.

You will then be automatically connected to the Internet, if you have an appropriate connection available. If an automatic connection is not possible, you will be asked about how you dial out from where you will be using your notebook. If you are not connected to a phone line and plan to register at a later time, you

may click the Skip button.

Once you are connected to the Internet, you will be asked if you wish to continue with the registration. If

you select Yes you will then enter your name and address, and email address if desired. Click Next to

complete registration.

- Starting Your M2010 Notebook

Registering your notebook with Fujitsu

You can register your notebook by going to our website at: us.fujitsu.com/computers. You will need to

be set up with an Internet Service Provider (ISP) to register online.



ClickMe!

Installing ClickMe!

BEFORE INSTALLING THE CLICKME! UTILITY, BE SURE THE WIRELESS LAN DEVICE IS ENABLED BY

PRESSING THE [FN] + [F5] KEY COMBINATION.

The first time you boot up your system, you will see an icon called Click Me! in the Start menu. We highly recommend that you install the ClickMe! utility the first time you boot up. When you click the Click

Me! icon, your system will automatically create the related icons in the system tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access, such as wireless LAN software provided by the wireless LAN manufacturer.

HERE MAY BE SOME THIRD-PARTY APPLICATIONS THAT DO NOT GET INSTALLED USING THE CLICKME! UTILITY. FOR MORE INFORMATION, REFER TO YOUR GETTING STARTED GUIDE.

 Fujitsu Driver Update Utility

Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 78.

- Starting Your M2010 Notebook

Power Management

Your notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.

Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly. For example, you can create an appropriate power saving profile, put your notebook into standby mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings.

Power/Suspend/Resume Button

When your notebook is active, the Power/Suspend/Resume button can be used to manually put the notebook into standby mode. Push the Power/Suspend/Resume button when the notebook is active, but not actively accessing anything, and immediately release the button.

If your notebook is suspended, pushing the Power/Suspend/Resume button returns your notebook to active operation. You can tell whether the system is Suspended by looking at the Power indicator. If the

indicator is visible and not flashing, your notebook is fully operational. If the indicator is visible and

flashing, your notebook is in standby mode. If the indicator is not visible, the power is off or your

notebook is in Hibernation mode. (See Hibernation Feature)

- Power Management

Standby Mode

Standby mode in Windows saves the contents of your system memory during periods of inactivity by maintaining power to critical parts. This mode turns off the CPU, display, hard drive, and all other internal components except those necessary to maintain system memory and for restarting.

Your notebook can be put in Standby mode by:

• Pressing the Power/Suspend/Resume button when your system is turned on.

• Selecting Standby from the Turn off computer menu.

• Timing out from lack of activity.

• Allowing the battery to reach the Dead Battery Warning condition.

Your notebook’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Standby mode, your notebook will return to the point where it left off. You must use the Power/Suspend/Resume button to resume operation, and there must be an adequate power source available, or your notebook will not resume.

■

IF RUNNING YOUR NOTEBOOK ON BATTERY POWER, BE AWARE THAT THE BATTERY CONTINUES TO DISCHARGE

WHILE YOUR NOTEBOOK IS IN STANDBY MODE, THOUGH NOT AS FAST AS WHEN FULLY OPERATIONAL.

■

DISABLING THE POWER/SUSPEND/RESUME BUTTON PREVENTS IT FROM BEING USED TO PUT THE NOTEBOOK INTO

LEEP OR HIBERNATION (SAVE-TO-DISK) MODE. THE BUTTON RESUME FUNCTION CAN’T BE DISABLED.

■

THE SLEEP OR HIBERNATION (SAVE-TO-DISK) MODE SHOULD NOT BE USED WITH CERTAIN PC CARDS. CHECK

YOUR PC CARD DOCUMENTATION FOR MORE INFORMATION. WHEN PC CARDS OR EXTER NAL DEVICES ARE IN USE, HIBERNATION (SAVE-TO-DISK) MODE CANNOT RETURN TO THE EXACT STATE PRIOR TO SUSPENSION, BECAUSE ALL OF THE PERIPHERAL DEVICES WILL BE RE-INITIALIZED WHEN THE SYSTEM RESTARTS.

■

IF YOUR NOTEBOOK IS ACTIVELY ACCESSING INFORMATION WHEN YOU ENTER STANDBY OR HIBERNATION MODE,

CHANGES TO OPEN FILES ARE NOT LOST. FILES ARE LEFT OPEN AND MEMORY IS KEPT ACTIVE DURING STANDBY MODE OR THE MEMORY IS TRANSFERRED TO THE INTERNAL HARD DRIVE DURING HIBERNATION MODE.

■

THE MAIN ADVANTAGE OF USING HIBERNATION IS THAT POWER IS NOT REQUIRED TO MAINTAIN YOUR DATA. THIS IS

PARTICULARLY IMPORTANT IF YOU WILL BE LEAVING YOUR NOTEBOOK IN A SUSPENDED STATE FOR A PROLONGED PERIOD OF TIME. THE DRAWBACK OF USING HIBERNATION MODE IS THAT IT LENGTHENS THE POWER DOWN AND POWER UP SEQUENCES AND RESETS PERIPHERAL DEVICES.

- Power Management

Hibernation (Save-to-Disk) Feature

The Hibernation feature saves the contents of your notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature.

Enable or Disable the Hibernation Feature

The default settings are not enabled. To enable or disable the Hibernation feature follow these steps:

1 From the Start menu, select Settings, and then select Control Panel. 2 From the Control Panel select Power Options. 3 Select the Hibernate tab. Select the box to enable or disable this feature.

Windows Power Management

The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Options to set the timeout values for turning off the display and hard disks whether you are running the notebook on battery power or one of the adapters.

Restarting the System

If your system is on and you need to restart it, be sure that you use the following procedure.

1 Click the [Start] button, and then click Turn Off Computer. 2 Select the Restart option. Your notebook will shut down and then reboot.

TURNING OFF YOUR NOTEBOOK WITHOUT EXITING WINDOWS OR TURNING ON YOUR NOTEBOOK WITHIN

SECONDS OF THE NOTEBOOK BEING SHUT OFF MAY CAUSE AN ERROR WHEN YOU START THE NEXT

TIME.

- Power Management

Powering Off

Before turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your notebook shuts down without error, use the Windows shut down procedure.

BE SURE TO CLOSE ALL FILES, EXIT ALL APPLICATIONS, AND SHUT DOWN YOUR OPERATING SYSTEM

PRIOR TO TURNING OFF THE POWER. IF FILES ARE OPEN WHEN YOU TURN THE POWER OFF, YOU WILL LOSE ANY CHANGES THAT HAVE NOT BEEN SAVED, AND MAY CAUSE DISK ERRORS.

Using the correct procedure to shut down from Windows allows your notebook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:

1 Click the [Start] button, and then click Turn Off Computer. 2 Select the Turn Off option.

If you are going to store your notebook for a month or more, see Care and Maintenance Section.

- Power Management

ENERGY STAR® Compliance

Your Fujitsu system is an ENERGY STAR® qualified mobile PC. By choosing a computer with the latest energy-saving technology, you’re helping to preserve our environment for future generations.

ENERGY STAR is a joint program of the U.S. Environmental Protection Agency, U.S.

Department of Energy, Natural Resources Canada, and other governments around the world

helping us save money while protecting the environment through energy efficient products and practices. With energy costs and global warming top-of-mind for consumers, Fujitsu is committed to offering solutions that help consumers conserve energy and improve the quality of our environment.

Sleep Mode: 

You will notice that your computer is initially set so that the display turns off after 15 minutes of user inactivity, and the computer goes into Sleep mode after 20 minutes of user inactivity. When going into Sleep mode, the computer also reduces the speed of any active Ethernet network links. To “wake” the computer from Sleep mode, press the Suspend/Resume Button.

Energy saving benefits:

Fujitsu ENERGY STAR qualified mobile PCs use about half as much electricity as standard equipment – saving half in utility costs. But more than that, ENERGY STAR also makes a difference for the environment. Did you know that the average house can be responsible for twice the greenhouse gas emissions as the average car? That’s because every time you flip on a light switch, run your dishwasher, or turn on your PC, you use energy, which means more greenhouse gas emissions from power plants. So the more energy we can save through energy efficiency, the more we help to reduce greenhouse gases and the risks of global warming.

To learn more about the important ENERGY STAR program, visit: www.energystar.gov.

To read about how Fujitsu is supporting Sustainable Management along with several other environmental activities, visit the Fujitsu Corporate Citizenship page at:

http://www.computers.us.fujitsu.com/www/content/aboutus/environmental/environment.php

- Power Management

Chapter 3

User-Installable Features

Lithium ion Battery

Your notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.

The Lithium ion battery operating time may become shorter if it is used under the following conditions:

• When used at temperatures that exceed a low of 5°C or a high of 35°C. Extreme temperatures not

only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range.

• When using a high current device such as an external optical drive or the hard drive, using the AC

adapter will conserve your battery life.

DO NOT LEAVE A FAULTY BATTERY IN YOUR NOTEBOOK. IT MAY DAMAGE YOUR AC ADAPTER, OPTIONAL

UTO/AIRLINE ADAPTER, ANOTHER BATTERY OR YOUR NOTEBOOK ITSELF. IT MAY ALSO PREVENT

OPERATION OF YOUR NOTEBOOK BY DRAINING ALL AVAILABLE CURRENT INTO THE BAD BATTERY.

• ACTUAL BATTERY LIFE WILL VAR Y BASED ON SCREEN BRIGHTNESS, APPLICATIONS, FEATURES,

POWER MANAGEMENT SETTINGS, BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES.

PTICAL DRIVE OR HARD DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE.

HE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF YOUR BATTERY IS

RUNNING LOW QUICKLY, YOU SHOULD REPLACE IT WITH A NEW ONE.

• UNDER FEDERAL, STATE, OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTING

THEM IN THE TRASH. PLEASE TAKE CARE OF OUR ENVIRONMENT AND DISPOSE OF BATTERIES PROPERLY. CHECK WITH YOUR LOCAL GOVERNMENT AUTHORITY FOR DETAILS REGARDING RECYCLING OR DISPOSING OF OLD BATTERIES. IF YOU CANNOT FIND THIS INFORMATION ELSEWHERE, CONTACT YOUR SUPPORT REPRESENTATIVE AT 1-800-8FUJITSU (1-800-838-5487)

Recharging the Batteries

If you want to know the condition of the primary Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes. (See Table 1 on page 27 for more information.)

The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your notebook and connect the AC or Auto/Airline adapter.

AKE SURE THAT THE BATTERY CHARGING INDICATOR AND THE BATTERY LEVEL INDICATOR ICON ON

THE STATUS INDICATOR PANEL LIGHT.

There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your notebook into

Standby mode, or turn it off while the adapter is charging the battery. (See Power Management on page

46 for more information on Standby mode and shutdown procedure)

- Lithium ion Battery

USING HEAVY CURRENT DEVICES OR FREQUENT EXTERNAL OPTICAL DRIVE ACCESSES MAY PREVENT

CHARGING COMPLETELY.

Low Battery State

When the battery is running low, the Battery Level indicator will glow red. If you do not respond to the low battery alarm, the batteries will continue to discharge until they are too low to operate. Your notebook will then go into Standby mode to try and protect your data for as long as possible. There is no guarantee that your data will not be lost once the system reaches this point.

■

ONCE THE LOW BATTERY NOTIFICATION MESSAGE APPEARS, YOU NEED TO SAVE ALL YOUR ACTIVE DATA AND PUT

YOUR NOTEBOOK INTO STANDBY MODE UNTIL YOU CAN PROVIDE A NEW POWER SOURCE. YOU SHOULD PROVIDE A CHARGED BATTERY, AN AC POWER ADAPTER, OR AUTO/AIRLINE ADAPTER AS SOON AS POSSIBLE.

■

WHEN YOU ARE IN STANDBY MODE THERE MUST ALWAYS BE AT LEAST ONE POWER SOURCE ACTIVE. IF YOU

REMOVE ALL POWER SOURCES WHILE YOUR NOTEBOOK IS IN STANDBY MODE, ANY DATA THAT HAS NOT BEEN SAVED TO THE HARD DRIVE WILL BE LOST.

Once your notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your system while an adapter is charging the battery.

Replacing the Battery

Your notebook comes with one battery pack; you might want to consider purchasing a spare. By keeping a spare battery fully charged, you can immediately swap with one that is not charged.

There are two ways to swap batteries: cold- and hot-swapping. Cold-swapping means swapping batteries when the system is powered down; hot-swapping is performed when the system is powered by AC power:

- Lithium ion Battery

Cold-swapping Batteries

Have a charged battery ready to install.

2 Shut down your system and disconnect the AC adapter. 3 Lift the display enough to pull the display latch from the slot. 4 Press the battery release latches to open the compartment. 5 Remove the battery from the compartment. 6 Slide the new battery into the compartment. 7 Close the compartment and the battery release latches will click into place. 8 Plug in the AC adapter and turn the power on.

Hot-swapping Batteries

To hot-swap batteries in your battery bay follow these easy steps:

BE SURE TO PLUG IN AN AC ADAPTER PRIOR TO REMOVING THE BATTERY. THERE IS NO BRIDGE

BATTERY PRESENT TO SUPPORT THE SYSTEM WHILE THE BATTERY IS BEING REPLACED. IF YOU DO NOT USE AN AC ADAPTER YOU WILL LOSE ANY UNSAVED FILES.

1 Close any open files and put your system into Standby mode. 2 Connect an AC adapter or Auto/Airline power adapter to provide power to the system. 3 Lift the display enough to pull the display latch from the slot. 4 Press the battery release latches inward to open the compartment. 5 Remove the battery from the compartment. 6 Slide the new battery into the compartment. 7 Close the compartment and the battery release latches will click into place. 8 Press the Suspend/Resume button to return your system to normal operation.

- Lithium ion Battery

F THE LITHIUM ION BATTERY CONNECTOR IS NOT FULLY SEATED, YOU MAY NOT BE ABLE TO USE YOUR

NOTEBOOK OR CHARGE YOUR BATTERY.

Figure 11. Removing a Battery

- Lithium ion Battery

Memory Upgrade Module

Your Fujitsu M2010 notebook comes with 1GB of high speed Double Data Rate Synchronous Dynamic RAM 2 (DDR2 SDRAM), 533 MHz factory installed. To increase your system’s memory capacity, you may remove the original module and replace it with a memory upgrade module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at www.shopfujitsu.com.

• DO NOT REMOVE ANY SCREWS FROM THE MEMORY UPGRADE MODULE COMPARTMENT EXCEPT THE

ONES SPECIFICALLY SHOWN IN THE DIRECTIONS FOR INSTALLING AND REMOVING THE MEMORY UPGRADE MODULE.

• THE MEMORY UPGRADE MODULE CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE

(ESD). T

• BEFORE HANDLING A MEMORY MODULE, TOUCH A GROUNDED METAL OBJECT TO DISCHARGE

STATIC ELECTRICITY BUILT UP IN YOUR BODY.

• WHEN INSTALLING OR REMOVING A MEMORY MODULE, HOLD IT BY THE EDGE SO AS NOT TO

TOUCH ANY CONTACTS OR CHIPS. BE CAREFUL NOT TO TOUCH ANY INTERNAL COMPUTER TERMINALS OR COMPONENTS; THE OIL FROM YOUR FINGERS COULD CAUSE A SHORT TO THE COMPONENTS.

• BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING MEMORY MODULES.

VEN IF THE SYSTEM IS IN HIBERNATE OR SLEEP STATES, DATA COULD BE LOST OR THE MEMORY

COULD BE DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.

O MINIMIZE RISK TO THE MODULE, OBSERVE THE FOLLOWING PRECAUTIONS:

Removing Memory Modules

1 Turn off power to your notebook and remove any power adapter (AC or auto/airline). 2 Make sure that all the connector covers are closed. 3 Turn the system bottom side up, and remove the screws of the memory upgrade module compartment.

(Figure 13).

4 Remove the cover. 5 Pull the clips sideways away from each side of the memory upgrade module at the same time. (Figure 13) 6 While holding the clips out, remove the module from the slot by lifting it up and pulling towards the rear of your

notebook.

- Memory Upgrade Module

7 Store the memory module in a static guarded sleeve. 8 Install a new module as outlined in the procedure below. 9 Replace the cover. 10 Replace the screws.

Figure 12. Opening the Memory Compartment Figure 13. Removing a Memory Module

- Memory Upgrade Module

Installing a Memory Upgrade Module

1 Remove the new memory upgrade

module from the static guarded sleeve.

2 Align the memory upgrade module with

the component side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. (Figure 14)

3 Insert the memory upgrade module at a

45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is properly in place.

4 Replace the cover. 5 Replace the screws.

HE MEMORY UPGRADE MODULE IS NOT SOMETHING YOU ROUTINELY REMOVE FROM YOUR NOTEBOOK.

NCE IT IS INSTALLED, YOU SHOULD LEAVE IT IN PLACE UNLESS YOU WANT TO CHANGE SYSTEM

MEMORY CAPACITY.

Figure 14. Installing a Memory Module

- Memory Upgrade Module

Checking the Memory Capacity

Once you have changed the system memory capacity by replacing the installed module with a larger one, be sure to check that your notebook has recognized the change.

Check the memory capacity by clicking [Start] > Control Panel, then double-clicking the System icon. Select the General tab and check the amount of memory in the General tab.

IF THE TOTAL MEMORY DISPLAYED IS INCORRECT, CHECK THAT YOUR MEMORY UPGRADE MODULE IS

PROPERLY INSTALLED. (IF THE MODULE IS PROPERLY INSTALLED AND THE CAPACITY IS STILL NOT CORRECTLY RECOGNIZED, SEE TROUBLESHOOTING ON PAGE 64.

- Memory Upgrade Module

Figure 15. Installing an SD Card

MS/SD Card Slot

SD Card

Memory Stick/Secure Digital Cards

Your notebook supports Memory Stick (MS) and Secure Digital (SD) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.

Memory Stick and Secure Digital Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. These cards transfer data quickly, with low battery consumption.

- Memory Stick/Secure Digital Cards

Inserting MS/SD Cards

MS and SD Cards are inserted in the MS/SD Card slot (Figure 15). To insert a card, follow these steps:

• INSERTING OR REMOVING AN MS OR SD CARD DURING YOUR NOTEBOOK’S SHUTDOWN OR BOOTUP

PROCESS MAY DAMAGE THE CARD AND/OR YOUR NOTEBOOK.

• DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD

AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR NOTEBOOK, OR BOTH.

1 See your card manual for instructions on the insertion of your card. Some cards may require that your system

is off while inserting them.

2 Make sure there is no card currently in the slot. If there is, see Removing an SD Card. 3 Insert your card into the slot with the product label facing up. 4 Push the card firmly into the slot until it is seated in the connector.

Removing an MS/SD Card

To remove a card, first see your card manual for instructions. Some cards may require your notebook to be in Suspend Mode or Off while removing them. Prior to removing the card from the slot, first select it using the Safely Remove Hardware icon in the notification area. To remove the card, push it in to release it, then pull it out.

- Memory Stick/Secure Digital Cards

Device Ports

Your M2010 notebook comes equipped with multiple device ports to which you can connect an external device including: disk drives, keyboards, modems, printers, etc.

Internal LAN (RJ-45) jack

The internal LAN (RJ-45) jack is used for an internal 10/100 BaseTx Ethernet connection. You will need to configure your notebook to work with your particular network. (Please refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these easy steps: (See Figure 4 on page 22 for location)

1 Align the connector with the jack opening. 2 Push the connector into the jack until it is seated. 3 Plug the other end of the cable into a LAN outlet.

Universal Serial Bus Ports

The three Universal Serial Bus 2.0 ports (USB) allow you to connect USB devices such as external floppy disk drives, external DVD drives, game pads, pointing devices, keyboards and/or speakers. USB 2.0 is downward-compatible with USB 1.1 devices, so older USB devices will work with these ports. USB 2.0 is a much faster design, running forty times faster than USB 1.1.

In order to connect a USB device, follow these easy steps: (See Figure 4 on page 22 for location)

1 Align the connector with the port opening. 2 Push the connector into the port until it is seated.

Microphone Jack

The microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your notebook.

In order to connect a microphone follow these easy steps: (Figure 4)

1 Align the connector with the port opening. 2 Push the connector into the port until it is seated.

- Device Ports

Headphone Jack

The headphone jack allows you to connect headphones or powered external speakers to your notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: (See Figure 4 on page 22 for location)

1 Align the connector with the port opening. 2 Push the connector into the port until it is seated.

IF YOU PLUG HEADPHONES INTO THE HEADPHONE JACK, THE BUILT-IN STEREO SPEAKERS WILL BE

DISABLED.

External Video Port

The external video port allows you to connect an external monitor or LCD projector. In order to connect an external device follow these easy steps: (See Figure 3 on page 20 for location).

1 Align the connector with the port opening. 2 Push the connector into the port until it is seated. 3 Tighten the two hold-down screws, located on each side of the connector.

HEN AN EXTERNAL MONITOR IS PLUGGED IN, PRESSING THE [FN] + [F10] KEYS ALLOWS YOU TO

CHANGE YOUR SELECTION OF WHERE TO SEND YOUR DISPLAY VIDEO. EACH TIME YOU PRESS THE KEY COMBINATION, YOU WILL STEP TO THE NEXT CHOICE, STARTING WITH THE BUILT-IN DISPLAY PANEL ONLY, MOVING TO THE EXTERNAL MONITOR ONLY, FINALLY MOVING TO BOTH THE BUILT-IN DISPLAY PANEL AND AN EXTERNAL MONITOR.

- Device Ports

Chapter 4

Troubleshooting Your Notebook

Troubleshooting

There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.

Identifying the Problem

If you encounter a problem, go through the following procedure before pursuing complex troubleshooting:

1 Turn off your notebook. 2 Make sure the AC adapter is plugged into your notebook and to an active AC power source. 3 Make sure that any devices connected to the external connectors are plugged in properly. You can also

disconnect such devices, thus eliminating them as possible causes of failure.

4 Turn on your notebook. Make sure it has been off at least 10 seconds before you turn it back on. 5 Go through the boot sequence. 6 If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed

troubleshooting information.

• IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE

ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE.

• DO NOT RETURN A FAIL ED NOTEBOOK TO YOUR SUPPLIER UNTIL YOU HAVE TALKED TO A SUPPORT

REPRESENTATIVE.

7 If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support

representative:

Toll free: 1-800-8Fujitsu (1-800-838-5487)  Web site: http://www.computers.us.fujitsu.com/support.

Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:

• Product name

• Product configuration number

• Product serial number

• Purchase date

• Conditions under which the problem occurred

• Any error messages that have occurred

• Type of device connected, if any

See the Configuration Label on the bottom of your notebook for configuration and serial numbers.

- Troubleshooting Your Notebook

Specific Problems

Using the Troubleshooting Table

When you have problems with your notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.

Troubleshooting Table

Problem Page

Audio Problems. . . . . . . . . . . . . . . . . . . . . . . page 67

Hard Drive Problems. . . . . . . . . . . . . . . . . . . page 67

Keyboard or Mouse Problems. . . . . . . . . . . . page 67

Memory Problems. . . . . . . . . . . . . . . . . . . . . page 68

USB Device Problems. . . . . . . . . . . . . . . . . . page 68

Problem Page

Power Failures . . . . . . . . . . . . . . . . . . . . . page 69

Shutdown and Startup Problems . . . . . . . page 71

Video Problems . . . . . . . . . . . . . . . . . . . . page 72

Miscellaneous Problems . . . . . . . . . . . . . page 73

- Troubleshooting Your Notebook

Problem Possible Cause Possible Solutions

Audio Problems

There is no sound coming from the built-in speakers.

The volume is turned too low. Adjust the volume control on your notebook and operating

The software volume control is set too low.

Headphones are plugged into your notebook.

The speakers have been muted using the Volume icon in the system tray.

Hard Drive Problems

You cannot access your hard drive.

The wrong drive designator was used by an application when a bootable disc was used to start the notebook.

Security is set so your operating system cannot be started without a password.

Keyboard or Mouse Problems

system. Use the [Fn+F9] key combination on your keyboard to increase the volume of your notebook.

Manually adjusting the volume (i.e., keyboard "hot keys") should dynamically adjust the volume of the operating system (see above). If that doesn’t work, adjust the sound volume control settings in your software or application.

Plugging in headphones disables the built-in speakers. Remove the headphones.

Click the Volume icon in the system tray on the bottom right of the screen. If the Mute box is checked, click on it. You can also press [Fn] + [F3] to toggle the audio on and off.

Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted.

Verify your password and security settings.

The built-in keyboard does not seem to work.

The notebook has gone into Standby mode.

Your application has locked out your keyboard.

NumLock key has been set. Press the NumLock key to toggle it off.

- Troubleshooting Your Notebook

Push the Power/Suspend/Resume button.

Try to use your integrated pointing device to restart your system.

Problem Possible Cause Possible Solutions

You have installed an  external keyboard or mouse, and it does not seem to work.

You have connected an external keyboard or a mouse and it seems to be locking up the system.

Your external device is not properly installed.

Your operating system (OS) is not set up with correct software driver for that device.

Your OS is not set up with the correct driver for that device.

Your system has crashed. Try to restart your notebook.

Memory Problems

Your System screen in the Control Panel does not show the correct amount of installed memory.

Your memory upgrade module is not properly installed.

You have a memory failure. Check for Power On Self Test (POST) messages. See

Modem Problems (optional external device)

Messages about modem operation.

Modem operation messages are generated by whichever modem application is in use.

USB Device Problems

You installed a USB device but your notebook does not recognize the device.

The device is not properly installed.

The device may have been installed while an application was running, so the notebook is not aware of its installation.

Re-install your device. See “Device Ports” on page 62.

Check your device and operating system documentation and activate the proper driver.

Check your device and operating system documentation  and activate the proper driver.

Remove and re-install your memory upgrade module. See

“Memory Upgrade Module” on page 56.

“Power On Self Test Messages” on page 74.

See your application software documentation for additional information.

Remove and re-install the device. See “Device Ports” on

page 62.

Close the application and restart your notebook.

Your device may not have the correct software driver active.

- Troubleshooting Your Notebook

See your software documentation and activate the correct driver.

Problem Possible Cause Possible Solutions

Power Failures

You turn on your notebook and nothing seems to happen.

The installed battery is completely discharged or there is no Power adapter (AC or

Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 26. Install a charged battery or a Power adapter.

Auto/Airline) installed.

The battery is installed but is faulty.

Use the Status Indicator panel to verify the presence and condition of the battery. See “Status Indicator Panel” on page 26. If the battery indicates a malfunction, remove it and  operate from another power source or replace that battery.

The battery is low. Check the Status Indicator Panel to determine the presence

and condition of the battery. See “Status Indicator Panel” on page 26. Use a Power adapter to operate until a battery is charged or install a charged battery.

The power adapter (AC or auto/airline) is not plugged in

Verify that your adapter is connected correctly. See “Power

Sources” on page 40.

properly.

The power adapter (AC or auto/airline) has no power from the AC outlet, airplane jack, or car cigarette lighter.

The power adapter (AC or

Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.

Try a different power adapter.

auto/airline) is faulty.

Your notebook turns off all by itself.

The power management parameters are set for auto timeouts which are too short for your operating needs.

- Troubleshooting Your Notebook

Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Options located in the Control Panel to adjust the timeout values to better suit your needs.

Problem Possible Cause Possible Solutions

Your notebook turns off all by itself. (continued)

Your notebook will not work on battery alone.

The battery seems to  discharge too quickly.

You are operating on battery power and ignored a low bat-

Install a power adapter, then push the Power/Sus-

pend/Resume button. See “Power Sources” on page 40. tery alarm until the battery was at the dead battery state and the system has entered Dead Battery Suspend mode.

You have a battery failure. Verify the condition of the battery using the Status Indicator

panel. If the battery is shorted, replace or remove it. See

“Status Indicator Panel” on page 26.

Your power adapter has failed or lost its power source.

Make sure the adapter is plugged in and the outlet has

power.

The installed battery is dead. Replace the battery with a charged one or install a power

adapter.

No battery is installed. Install a charged battery.

The battery is improperly

Verify that the battery is properly connected by re-installing it.

installed.

Your installed battery is faulty. Verify the condition of the battery using the Status Indicator

panel and replace or remove any batteries that are shorted.

See “Status Indicator Panel” on page 26.

The power savings features may be disabled.

Check the Power Options menu settings and adjust according to your operating needs.

You are running an applica-

Use a power adapter for this application when at all possible. tion that uses a lot of power due to frequent hard drive access or optical drive access, or use of a Wireless LAN or other device.

The battery is very old. Replace the battery.

- Troubleshooting Your Notebook

Problem Possible Cause Possible Solutions

The battery seems to  discharge too quickly.

The brightness is turned all the way up.

(continued)

Battery has been exposed to high temperatures.

The battery is too hot or too cold.

Shutdown and Startup Problems

The Suspend/Resume  button does not work.

The system powers up, and displays power on information, but fails to load the operating system.

Suspend/Resume button is disabled.

There may be application software conflict.

The boot sequence settings o

f the setup utility are not compatible with your configuration.

You have a secured system requiring a password to load your operating system.

Turn down the brightness adjustment. The higher the brightness the more power your display uses.

Replace the battery.

Restore the notebook to normal operating temperature. Charging icon on the Status Indicator panel will flash when battery is outside of operating range.

Enable the button by going to the Control Panel > Power Options Properties and clicking on the Advanced tab. In the Power buttons area, select the option that suits your needs.

Close all applications and try the button again.

Set the operating source by pressing the [ESC] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. See “BIOS Setup Utility” on page 42.

Make sure you have the right password. Enter the setup utility and verify the Security settings and modify them as accordingly. See “BIOS Setup Utility” on page 42.

An error message is  displayed on the screen during the boot sequence.

Your notebook appears to change setup parameters when you start it.

Power On Self Test (POST) has detected a problem.

BIOS setup changes were not saved when made and you exited the setup utility.

- Troubleshooting Your Notebook

See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. See “Power On

Self Test Messages” on page 74.

Make sure you select Save Changes And Exit when exiting the BIOS setup utility.

Problem Possible Cause Possible Solutions

Your notebook appears to change setup parameters when you start it..

(continued)

Video Problems

The built-in display is blank when you turn on your notebook.

The notebook turned on with a series of beeps and the built-in display is blank.

The BIOS CMOS hold-up battery has failed.

An external monitor is plugged in, and the system is set for an external monitor only.

Display angle and brightness settings are not adequate for your lighting conditions.

Power management timeouts are set for short intervals and you didn’t see the display go on and off again.

Power On Self Test (POST) detected a failure which does not allow display to operate.

Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years.

Pressing [F10] while holding down [Fn] allows you to change where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order are: built-in display, external monitor, both built-in display and external monitor.

Move the display and the brightness control until you have adequate visibility. Pressing either the [F6] or [F7] keys while holding down the [Fn] key also allows you to change the brightness level of the display.

Press a keyboard button or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. (The display may be shut off by Standby mode, Auto Suspend or Video Timeout)

Contact your support representative.

The display goes blank by itself after you have been using it.

The display does not close.

The notebook has gone into Video timeout, Standby mode, or Save-to-Disk mode because you have not used it for a period of time.

Foreign object stuck between display and keyboard.

- Troubleshooting Your Notebook

Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. Check power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. See “BIOS Setup Utility” on page 42.

Remove all foreign objects, such as a paperclip, from the keyboard.

Problem Possible Cause Possible Solutions

The display goes blank by itself after you have been using it. (continued)

The display has bright or dark spots.

The application display uses only a portion of  your screen and is surrounded by a dark frame.

You connected an external monitor and it does not display any information.

You have connected an external monitor and it does not come on.

Power timeouts are set for very short intervals and you failed to notice the display come on and go off again.

If the spots are very tiny and few in number, this is normal for a large LCD display.

If the spots are numerous or large enough to interfere with your operation needs.

You are running an application that does not support the system’s native resolution and display compression is enabled.

Your external monitor is not properly installed.

Your operating system is not setup with the correct software driver for that device.

Your external monitor is not compatible with your notebook.

Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout)

This is normal; do nothing.

Display is faulty; contact your support representative.

Display compression gives a clearer but smaller display for applications that do not support the system’s native pixel  resolution. You can fill the screen but have less resolution by changing display compression settings. These settings can be changed in the Intel GMA control panel.

Reinstall your device. See “External Video Port” on page 63.

Check your device and operating system documentation and activate the proper driver.

See your monitor documentation and the External Monitor Support portions of the Specifications section. See “Specifications” on page 87.

Miscellaneous Problems

Error message displayed on the screen during operation of an application.

Application software often has its own set of error message displays.

- Troubleshooting Your Notebook

See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.

Power On Self Test Messages

The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.

Check date and time settings

Verify that the date and time settings are correct.

*Extended Memory Failed at address line: nn

Extended memory not working or not configured properly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is properly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.

*Failure Fixed Disk n

The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.

Fan error has occurred

POST has determined that there is an error with the system fan. Contact your support representative.

*Invalid system disk

Problem with the system disk. Replace the disk and then press any key to continue.

- Troubleshooting Your Notebook

*Keyboard error

Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.

Non-system disk or disk error

Replace the disk and then press any key to continue.

NTLDR is missing

Press any key to restart.

*Operating system not found

Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted.

*Press <F1> to resume, <F2> to SETUP

Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings.

PXE-E32: TFTP open timeout

Contact your support representative for more information.

PXE-E53: No boot filename received

Contact your support representative for more information.

PXE-E61: Media test failure, check cable

Check the system cables. If that does not correct the failure, contact your support representative for more information.

- Troubleshooting Your Notebook

PXE-E78: Could not locate boot server

Contact your support representative for more information.

PXE-E89: Could not download boot image

Contact your support representative for more information.

*Real time clock error

Real-time clock fails BIOS test. May require board repair. Contact your support representative.

Remove disks or other media

Remove disks or other media, then press any key torestart.

*Stuck key

BIOS discovered a stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.

*System CMOS checksum bad – Default configuration used

BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.

*System timer error

The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.

Thermal sensor error has occurred

The thermal sensor has either failed or is out of thermal range.

- Troubleshooting Your Notebook

Restoring Your System Image and Software

Copies of your system images, applications, and drivers are available in two locations:

Hard Drive-based Factory Image: The original factory image of your system is stored in a hidden

partition on your hard disk drive in order to ensure that it is not inadvertently damaged. For instructions on restoring the factory image, please follow the instructions in the “Recovering Your Factory and System Images” manual that is bundled separately with your system. Note that in the event of a hard disk drive failure, you will need to contact Fujitsu Service and Support for instructions on obtaining a copy of the recovery media.

IN ORDER TO MAKE COPIES OF DRIVERS AND APPLICATIONS, YOU MUST HAVE AN EXTERNALLY

CONNECTED DVD DRIVE.

Hard Drive-based Drivers and Applications: On your desktop, there is a Backup Drivers & Apps icon

that allows you to back up and restore your drivers and applications by first backing them up to a disc on

an external drive. You are strongly encouraged to make a backup of the drivers and applications in the event of hard disk failure. The drivers and applications DVD ISO image is stored on the D: partition

(D:\Fujitsu\Drivers and Utilities Image). Please ensure that you do not delete the image before creating backup media. Note that in the event you need to reinstall any drivers or applications, if you have not made a backup of the drivers and applications you will need to download them from the Fujitsu Support website:

http://www.computers.us.fujitsu.com/support.

For more information on backing up your drivers and applications, please follow the instructions in the “Recovering Your Factory and System Images” manual that is bundled separately with your system.

User-Configured System Backups: The MyRecovery icon also allows you to make backups of your

current system image either to another location on your hard drive or on removable media. Backups can be made on a regular basis so that you can restore your system to a previous state.

- Restoring Your System Image and Software

• IN ORDER TO MAKE COPIES OF SYSTEM BACKUP IMAGES, YOU MUST HAVE AN EXTERNALLY

CONNECTED DVD DRIVE.

• IF YOU HAVE ACCESS TO THE INTERNET, VISIT THE FUJITSU SUPPORT WEBSITE OCCASIONALLY AT

HTTP://WWW.COMPUTERS.US.FUJITSU.COM/SUPPORT TO CHECK FOR THE MOST CURRENT INFORMATION, DRIVERS, AND SYSTEM UPDATES.

To use the recovery utilities, please follow the instructions in the “Recovering Your Factory and System Images” manual that is bundled separately with your system.

Automatically Downloading Driver Updates

The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one). If the icon does not appear in the system tray, go to [Start] -> All Programs, and click on Fujitsu Driver Update; this will create the icon automatically.

To invoke the FDU menu, right-click on the FDU icon. The menu contains the following items:

Check for updates now

Allows for manual driver update search. The first time it is used, you are prompted to agree to a user agreement. After clicking on the icon, the FDU automatically connects with the Fujitsu site to check for updates and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be used while the download is in process. When the update is complete, a message appears informing you of the fact.

Enable Automatic Update Notifications

Automatically searches for new updates on a regular basis (approximately every 3 days).

- Restoring Your System Image and Software

Show update history

Brings up a screen that displays a history of updates that have been made via the FDU.

About Fujitsu Driver Update

Displays the FDU version number and copyright information.

Fujitsu Driver Update Readme

Displays the FDU readme.

- Restoring Your System Image and Software

Chapter 5

Care and Maintenance

Caring for your M2010 Notebook

If you use your Fujitsu notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices.

• IN THE EVENT YOU DROP YOUR NOTEBOOK OR DAMAGE THE HOUSING IN ANY WAY, IMMEDIATELY TURN OFF POWER

AND DISCONNECT THE POWER PLUG. FAILURE TO DO SO COULD RESULT IN A SHORT CIRCUIT, SMOKE, AND/OR FIRE.

ONTACT FUJITSU SERVICE AND SUPPORT BY PHONE AT 1-800-8FUJITSU (1-800-838-5487), BY EMAIL AT

C 8FUJITSU@US.FUJITSU.COM, OR THROUGH THE WEBSITE AT HTTP://WWW.COMPUTERS.US.FUJITSU.COM/SUPPORT

TO LEARN HOW TO GET THE SYSTEM REPAIRED.

• THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).

TO MINIMIZE RISK TO THE COMPONENTS, OBSERVE THE FOLL OWING PRECAUTIONS:

- B

EFORE DOCKING OR UNDOCKING YOUR NOTEBOOK (WHEN USING A PORT REPLICATOR), IT IS A GOOD IDEA TO

ALWAYS TOUCH A GROUNDED METAL OBJECT TO DISCHARGE STATIC ELECTRICITY BUILT UP IN YOUR BODY.

- B

E SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING SYSTEM COMPONENTS. EVEN IF THE SYSTEM IS IN HIBERNATE OR SLEEP STATES, DATA COULD BE LOST OR MEMORY COULD BE DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.

- W

HEN INSTALLING OR REMOVING A MEMORY MODULE, HOLD IT BY THE EDGE SO AS NOT TO TOUCH ANY CONTACTS OR CHIPS. BE CAREFUL NOT TO TOUCH ANY INTERNAL COMPUTER TERMINALS OR COMPONENTS; THE OIL FROM YOUR FINGERS COULD CAUSE A SHOR T TO THE COMPONENTS.

• ELECTRICAL EQUIPMENT MAY BE HAZARDOUS IF MISUSED. OPERATIONS OF THIS PRODUCT OR SIMILAR PRODUCTS,

MUST ALWAYS BE SUPERVISED BY AN ADULT. DO NOT ALLOW CHILDREN ACCESS TO THE INTERIOR OF ANY ELECTRICAL PRODUCTS AND DO NOT PERMIT THEM TO HANDLE ANY CABLES.

• Your notebook is a durable but sensitive electronic device. Treat it with respect and care.

• Make a habit of transporting it in a suitable carrying case.

• Do not attempt to service the computer yourself. Always follow installation instructions closely.

• Keep it away from food and beverages.

• To protect your notebook from damage and to optimize system performance, be sure to keep all air

vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending

upon the environment in which the system is used.

• Do not operate the notebook in areas where the air vents can be obstructed, such as in tight

enclosures or on soft surfaces like a bed or cushion.

• If you accidentally spill liquid on your notebook:

1 Tu r n i t o f f . 2 Position it so that the liquid can run out. 3 Let it dry out for 24 hours, or longer if needed. 4 If your notebook will not boot after it has dried out, call your support representative.

• Do not use your Fujitsu notebook in a wet environment (near a bathtub, swimming pool).

• Always use the AC adapter and batteries that are approved for your notebook.

• Avoid exposure to sand, dust and other environmental hazards.

• Do not expose your notebook to direct sunlight for long periods of time as temperatures above 140°

F (60° C) may damage your notebook.

• Do not put heavy or sharp objects on the computer.

• If you are carrying your notebook in a briefcase, or any other carrying case, make sure that there

are no objects in the case pressing on the lid.

• Never position your notebook such that the optical drive is supporting the weight of the notebook.

- Care and Maintenance

Cleaning your notebook

• Always disconnect the power plug. (Pull the plug, not the cord.)

• Clean your notebook with a damp, lint-free cloth. Do not use abrasives or solvents.

• Use a soft cloth to remove dust from the screen. Never use glass cleaners.

• Always shut down the computer, unplug the power adapter, and remove the battery when cleaning

or disinfecting the computer exterior, keyboard or LCD display.

Cleaning guidelines using recommended off-the-shelf cleaners

Computer exterior, computer keyboard

To clean the exterior and keyboard, use one of the following off-the-shelf products:

• Office Depot® #154-616 Notebook Cleaning Kit

• Meridrew Enterprises Klear_Screen® Wipes

• 3M CL563 Cleaner Wipes

Note: After cleaning with one of these products, gently polish with a dry, soft, lint-free cloth until the solution is no longer visible.

LCD display

To clean the LCD display, use one of the following off-the-shelf products:

• Office Depot® #154-616 Notebook Cleaning Kit

• Meridrew Enterprises Klear_Screen® Wipes

* Applies to Tablet PC, convertible PC with LCD shield, and standard notebook LCD displays.

Wipe the LCD surface gently, allowing it to dry before turning on the computer.

- Care and Maintenance

Disinfecting notebook computers

Wipe the surface with a soft cloth wipe and a 50% ethanol solution or use another ethanol-based germicide which has been registered as a hospital disinfectant by the EPA.

• USE OF INCORRECT CLEANERS CAN RESULT IN OPTICAL IMPAIRMENT OF THE LCD AND/OR DAMAGE TO

THE COMPUTER. ALWAYS REFER TO THE CLEANER MANUFACTURER'S GUIDELINES AND MATERIAL SAFETY DATA SHEETS FOR PROPER HANDLING AND USE OF THE PRODUCTS.

• NEVER USE AMMONIA, ACIDIC, OR ALKALINE CLEANERS OR ORGANIC CHEMICALS SUCH AS PAINT

THINNER, ACETONE, PROPYL OR ISOPROPYL ALCOHOL, OR KEROSENE. IT MAY DAMAGE SURFACE FINISHES AND THE COATING OF THE LCD SCREEN.

• NEVER USE COMPRESSED AIR FOR CLEANING YOUR NOTEBOOK.

Storing your notebook

• If storing your notebook for a month or longer, turn your notebook off, fully charge the battery, then

remove and store all Lithium ion batteries.

• Store your notebook and batteries separately. If you store your notebook with a battery installed,

the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your notebook.

• Store your Fujitsu notebook in a cool, dry location. Temperatures should remain between 13ºF 

(-25ºC) and 140ºF (60ºC).

• ALWAYS POWER OFF THE COMPUTER BEFORE TRANSPORTING AND/OR PACKAGING IT. AFTER SHUTTING

DOWN THE SYSTEM, WAIT UNTIL THE STATUS LED PANEL INDICATES POWER OFF CONDITION (NO LIGHTS ARE ILLUMINATED).

• IT IS POSSIBLE THAT THE UNIT MAY NOT AUTOMATICALLY GO TO POWER OFF OR HIBERNATE MODE

WHEN YOU CLOSE THE LID. THIS SITUATION MAY OCCUR DUE TO PRE-OS BOOT PASSWORD SECURITY SETTINGS OR SOME OTHER APPLICATION RUNNING ON THE COMPUTER.

• ATTEMPTING TO TRANSPORT THE COMPUTER WHILE POWER IS ON MAY DAMAGE THE NOTEBOOK DUE

TO SHOCK OR OVERHEATING SINCE THE AIR VENTS MAY BE BLOCKED OR RESTRICTED.

- Care and Maintenance

Traveling with your notebook

• Do not transport your notebook while it is turned on.

• It is recommended that you carry your notebook with you while traveling, rather than checking it

in as baggage.

• Always bring your System Recovery CD that came with your notebook when you travel. If you

experience system software problems while traveling, you may need it to correct any problems.

• Never put your notebook through a metal detector. Have your notebook hand-inspected by security

personnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel. Security officials may require you to turn your notebook on, so make sure you have a charged battery on hand.

• Take the necessary plug adapters if you're traveling overseas. Check the following diagram to

determine which plug adapter you'll need or ask your travel agent.

Outlet Type Location Outlet Type Location

Russia and the Commonwealth

United States, Canada, parts of Latin

ica, Mexico, Japan, Korea,

Amer

the Philippines, Taiwan

f Independent States (CIS), most

of Europe, parts of Latin America,

the Middle East, parts of Africa,

Hong Kong, India, most of South Asia

United Kingdom, Ireland, Malaysia,

apore, parts of Africa

Sing

- Care and Maintenance

China, Australia, New Zealand

Batteries

Caring for your Batteries

• Always handle batteries carefully.

• Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object).

Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.

• Do not drop, puncture, disassemble, mutilate or incinerate the battery.

• Recharge batteries only as described in this manual and only in ventilated areas.

• Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten the life

of your battery.

• Do not leave a battery in storage for longer than 6 months without recharging it.

Increasing Battery Life

• Power your notebook through the AC or optional auto/airline adapter whenever possible.

• If your notebook is running on battery power all day, connect it to the AC adapter overnight to

recharge the battery.

• Keep brightness to the lowest level comfortable.

• Set the power management for maximum battery life.

• Put your notebook in standby mode when it is turned on and you are not actually using it.

• Limit your media drive access.

• Disable the Media Player auto insert notification function.

• Always use fully charged batteries.

• Eject PC Cards when not in use.

- Care and Maintenance

Media Care

Caring for your Media (optional)

Media discs (DVD/CD/CD-R) are precision devices and will function reliably if given reasonable care.

• Always store your media disc in its case when it is not in use.

• Always handle discs by the edges and avoid touching the surface.

• Avoid storing any media discs in extreme temperatures.

• Do not bend media discs or set heavy objects on them.

• Do not spill liquids on media discs.

• Do not scratch or get dust on media discs.

• Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.

• If a media disc is subjected to a sudden change in temperature, cold to warm condensation may form

on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry media discs.

• If a disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting

from the inner edge and wiping to the outer edge.

Caring for your Optical Drive (optional)

The optional external optical drive is durable but you must treat it with care. Pay attention to the following:

• The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock 

or vibration with the power on.

• Avoid using or storing the drive where it is damp, dusty, or will be exposed to extreme temperatures.

• Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.

• Avoid using or storing the drive where it will be subjected to shock or vibration.

• Do not disassemble or dismantle the optical drive.

e of a commercially available lens cleaner is recommended for regular maintenance of the drive.

• Us

- Care and Maintenance

Chapter 6

Hard Drive

Part Number

Processor

Model #

Memory

Operating System

Screen Size/Type

Configuration ID

Communications

Camera

Powe r

System Specifications

Specifications

This section provides the hardware and environmental specifications for your Fujitsu M2010 notebook. Specifications of particular configurations will vary.

Configuration Label

The configuration label located on the bottom of your notebook contains specific information regarding the options you’ve chosen for your notebook. Following is an example configuration label.

Configuration P/N: CP4XXXX-XX

FPC P/N: FPCMXXXXXX

M2010,N280,10.1”WSVGA,XPH,1G,160G,WLAN,BT,WEBCM,AC ADAPTER

Microprocessor

Intel® Atom™ N280 Processor

Chipset

• Mobile Intel 945GSE

• I/O Controller Hub 7 Mobile (ICH7M)

Memory

System Memory

• DDR2-533 MHz SDRAM memory module.

• One DIMM slot; upgradeable.

Cache Memory

512 KB L2 cache on-die

Video

Built-in color flat-panel TFT active matrix LED backlight display with simultaneous display capability.

Video Color and Resolution

10.1" Wide SVGA display

• Internal: 1024 x 600 pixel resolution (16:9), 16M colors

• External: 1600 x 1200 pixel resolution, 16M colors

Video RAM

Intel® Graphics Media Accelerator 945GSE video graphics. Up to 128 MB shared video memory using Dynamic Video Memory Technology (DVMT)

- Specifications

Audio

• Realtek codec ALC269 with High Definition (HD) audio.

• Headphones: Stereo headphone jack, 3.5 mm, 1 V

• Microphone: Stereo microphone jack, 3.5 mm, 100 mV

or less, minimum impedance 32 Ohms

rms

or less, minimum impedance 10K Ohms

p-p

• Two built-in stereo speakers

• One built-in digital mono microphone

Mass Storage Device Options

Hard Drive

Serial ATA, 150 Mbps data buffer, 5400 rpm, 2.5”

Features

Integrated Pointing Device

Touchpad cursor control

Communications

• Gigabit LAN: Internal wired 10/100 Ethernet LAN

• WLAN: Atheros HB63

• Bluetooth: Bluetooth V2.1 device for wireless personal area network communication

• Wireless LAN antenna

Theft Prevention Lock

Lock slot for use with security restraint systems.

- Specifications

Device Ports

On the notebook:

• Memory Stick/Secure Digital (MS/SD) Card slot

• One 15-pin D-SUB connector for VGA external monitor (see Display specifications)

• Three USB 2.0 (Universal Serial Bus) connectors for input/output devices

• One DC In connector

• One LAN (RJ-45) connector

• One stereo headphone jack

• One stereo microphone/line-in jack

Keyboard

Built-in keyboard with all functions of 101 key PS/2 compatible keyboards.

• Total number of keys: 80

• Function keys: F1 through F11/12, plus Fn extension key

• Two Windows keys: one Start key, one application key

• Key pitch: 16 mm; key stroke: 2.0 mm

• Left and right buttons

• External USB keyboard/mouse support

Power

Battery

Standard Lithium ion battery, rechargeable, 6-cell 10.8V, 4800 mAh

AC Adapter

Autosensing 100-240V AC, supplying 19V DC, 3.16A, to the notebook; includes an AC cable

- Specifications

Power Management

Conforms to ACPI (Advanced Configuration and Power Interface).

Dimensions and Weight

Overall Dimensions

Approximately 10.16"(w) x 7.4"(d) x 1.26” / 1.69” (h) (258 mm x 188 mm x 32 mm / 42.9 mm)

Weight

Approximately 2.93 lb. (1.33 Kg) with battery

Environmental Requirements

Temperature

Operating: 41° to 95° F (5° to 35° C). Non-operating: 5° to 140° F (–15° to 60° C)

Humidity

Operating: 20% to 85%, relative, non-condensing. Non-operating: 8% to 85%, relative, non-condensing

Altitude

Operating: 10,000 feet (3,048 m) maximum

Popular Accessories

For ordering or additional information on Fujitsu accessories please visit our Web site at  www.shopfujitsu.com or call 1-800-FUJITSU.

- Specifications

Included Software

Depending on your operating system, your notebook comes with software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. The following list indicates the software included with your system.

• Adobe Acrobat Reader

• Norton Internet Security™ (90-day free trial)

• Arcsoft WebCam Companion

• Google Desktop

• Google Tool Bar

• Google Picasa

• Fujitsu Driver Update utility

• Microsoft Works with Office 2007 Student and Home Trial Edition

Learning About Your Software

Tuto ria ls

All operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application.

Manuals

Included with your notebook you will find manuals for your installed operating system and other preinstalled software. Any manuals that are not included, are available online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications.

- Specifications

Adobe Acrobat Reader

The Adobe Acrobat Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms.

Norton Internet Security

Your system is preinstalled with a free 90-day trial version of Symantec’s Norton Internet Security™. Norton Internet Security is a suite of tools designed to protect your notebook from computer viruses, hackers, spyware, and spam. It assists in the protection of data currently on your hard disk from destruction or contamination. The trial version is activated upon your acceptance of software license agreement. After 90 days, you will need to purchase a subscription from Symantec to download latest virus, spyware, and spam definitions.

ArcSoft WebCam Companion

WebCam Companion offers a variety of webcam-optimized functions such as automatically recording movement detected by the cam, launching video chat sessions, capturing still and video images, and editing photos.

Google Desktop

Google Desktop lets you to search the contents of your computer for emails, web history, and files. It also allows you to view news and photos from anywhere on your desktop.

Google Picasa

Google Picasa lets you to search for, locate, move and label all of the photos on your computer.

Google Toolbar

Google Toolbar lets you to search the Internet quickly, block pop-ups, and perform a variety of other tasks to make your Internet experience easier and more pleasant.

- Specifications

Fujitsu Driver Update Utility

The Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. See “Automatically Downloading Driver Updates” on page 78.

Microsoft Works with Office 2007 Student and Home Trial Edition

Microsoft Works 9.0 is a software suite containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory.

- Specifications

Glossary

AC Adapter

A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your notebook.

Access point

Wireless network device used to bridge wireless and wired network traffic.

ACPI

Advanced Configuration and Power Interface

Active-Matrix Display

A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.

Ad Hoc Mode

Ad Hoc Mode refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion.

ADSL

Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines.

AGP

Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators.

Auto/Airline Adapter

A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your notebook.

BIOS

Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your notebook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.

Bit

An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).

bps

An abbreviation for bits per second. Used to describe data transfer rates.

Boot

To start-up a computer and load its operating system from disk, ROM or other storage media into RAM.

- Glossary

Bus

An electrical circuit which passes data between the CPU and the sub-assemblies inside your notebook.

Byte

8 bits of parallel binary information.

Cache Memory

A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.

CD-ROM

Compact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.

Channel

Range of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.

Command

An instruction which you give your operating system. Example: run a particular application or format a floppy disk.

Configuration

The combination of hardware and software that makes up your system and how it is allocated for use.

Data

The information a system stores and processes.

- Glossary

Direct current. A voltage or current that does not fluctuate periodically with time.

Default Value

A pre-programmed value to be used if you fail to set your own.

DHCP

Dynamic Host Configuration Protocol. A protocol used to automatically acquire parameters required for the communication, such as IP address. The sender of IP address is called a DHCP server, and the receiver is called a DHCP client.

DIMM

Dual-in-line memory module.

Disk

A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.

Disk Drive

The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.

Diskette

A floppy disk in a hard housing with a shutter.

DMA

Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.

- Glossary

DMI

Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals.

DNS

Domain Name System. A function to control the association between the IP address and the name assigned to the computer. If you do not know the IP address but if you know the computer name, you can still communicate to that computer.

DOS

Disk Operating System (MS-DOS is a Microsoft Disk Operating System).

Driver

A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.

DVMT

Dynamic Video Memory Technology. A video memory architecture that increases the efficiency of the motherboard by using innovative memory utilization and direct AGP.

Encryption Key (Network Key)

Data encryption key used to encrypt message text and for computing message integrity checks. Data encryption protects data from unauthorized viewing.

This device uses the same encryption key to encode and decode the data, and the identical encryption key is required between the sender and receiver.

- Glossary

ESD

Electrostatic Discharge. The sudden discharge of electricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.

FCC

Federal Communication Commission.

Gigabyte. One billion bytes.

Hard drive

A spinning platter of magnetic data storage media where the platter is very stiff.

I/O

Input/Output. Data entering and leaving your notebook in electronic form.

I/O Port

Connector and associated control circuits for data entering and leaving a notebook in electronic form.

IDE

Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.

IEEE802.11a

Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands.

IEEE802.11b

Wireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the

2.4 GHz ISM band.

100

- Glossary

Fujitsu LifeBook M2010 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

About This Guide

Conventions Used in the Guide

Fujitsu Contact Information

Getting to Know Your Notebook

Overview

Locating the Controls and Connectors

Front and Display Components

Left-Side Panel Components

Right-Side Panel Components

Bottom Components

Status Indicator Panel

Wireless Device Emission Indicator

Power Indicator

Battery Charge/DC-In Indicator

Hard Drive Access Indicator

CapsLock Indicator

NumLk Indicator

Display Panel

Opening the Display Panel

Adjusting Display Panel Brightness

Keyboard

Using the Keyboard

Touchpad Pointing Device

Clicking

Double-Clicking

Dragging

Touchpad Control Adjustment

Volume Control

Controlling the Volume

Getting Started with Your Notebook

Power Sources

Connecting the Power Adapters

Starting Your M2010 Notebook

Power On

Boot Sequence

BIOS Setup Utility

Booting the System

Starting Windows XP the First Time

Installing ClickMe!

 Fujitsu Driver Update Utility

Power Management

Power/Suspend/Resume Button

Standby Mode

Hibernation (Save-to-Disk) Feature

Windows Power Management

Restarting the System

Powering Off

ENERGY STAR® Compliance

User-Installable Features

Lithium ion Battery

Recharging the Batteries

Replacing the Battery

Memory Upgrade Module

Removing Memory Modules

Installing a Memory Upgrade Module

Checking the Memory Capacity

Memory Stick/Secure Digital Cards

Inserting MS/SD Cards

Removing an MS/SD Card

Device Ports

Internal LAN (RJ-45) jack

Universal Serial Bus Ports

Microphone Jack

Headphone Jack

External Video Port

Troubleshooting Your Notebook

Troubleshooting

Identifying the Problem

Specific Problems

Troubleshooting Table

Power On Self Test Messages

Restoring Your System Image and Software

Automatically Downloading Driver Updates

Care and Maintenance

Caring for your M2010 Notebook