Fujitsu D3034 Technical Manual

Technical Manual - English

System Board D3034
for PRIMERGY RX100 S7

Technical Manual

Edition August 2012

Comments… Suggestions… Corrections…

The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.

Feel free to send us your comments by e-mail to

[e-mail].

Certified documentation
according to DIN EN ISO 9001:2008

To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Copyright and Trademarks

Copyright © 2011 Fujitsu Technology Solutions GmbH.

All rights reserved.
Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

Ê The contents of this manual may be revised without prior notice.

Ê Fujitsu assumes no liability for damages to third party copyrights or other rights arising from

the use of any information in this manual.

Ê No part of this manual may be reproduced in any form without the prior written permission

of Fujitsu.

Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.

Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

D3034 (RX100 S7) Technical Manual

Before reading this manual

For your safety

This manual contains important information for safely and correctly using this
product.

Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.

Radio interference

This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A

Aluminum electrolytic capacitors

The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.

As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.

High safety use

This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.

When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).

The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.

Technical Manual D3034 (RX100 S7)

These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.

Measures against momentary voltage drop

This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.

(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)

Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan

Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.

Harmonic Current Standards

This product conforms to harmonic current standard JIS C 61000-3-2.

Only for the Japanese market:
About SATA hard disk drives

The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.

Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:

http://jp.fujitsu.com/platform/server/primergy/harddisk/

D3034 (RX100 S7) Technical Manual

Only for the Japanese market:

Shielded LAN cables should be used in this product.

Only for the Japanese market:

I Although described in this manual, some sections do not apply to the

Japanese market. These options and routines include:

– USB Flash Module (UFM)

– CSS (Customer Self Service)

Technical Manual D3034 (RX100 S7)

D3034 (RX100 S7) Technical Manual

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.1 Notational conventions . . . . . . . . . . . . . . . . . . . . 10

2 Important information . . . . . . . . . . . . . . . . . . . . . 11

2.1 CE certificate of conformity . . . . . . . . . . . . . . . . . . 11

2.2 Environmental protection . . . . . . . . . . . . . . . . . . . 12

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.2 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.2.1 Module population . . . . . . . . . . . . . . . . . . . . . . . . 21

3.2.1.1 Types of memory modules . . . . . . . . . . . . . . . . . . 21

3.2.1.2 Modes of operation . . . . . . . . . . . . . . . . . . . . . . 22

3.3 PCI slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.4 Screen resolution . . . . . . . . . . . . . . . . . . . . . . . 25

3.5 Temperature / system monitoring . . . . . . . . . . . . . . . 26

3.6 Connectors and indicators . . . . . . . . . . . . . . . . . . 27

3.6.1 System board . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3.6.2 Connector panel . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.7 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.7.1 Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Technical Manual D3034 (RX100 S7)

Contents

D3034 (RX100 S7) Technical Manual 9

1 Introduction

This technical manual describes the system board D3034, which can be
equipped with one processor.

For additional driver information (if available), refer to the Readme files located
on the server hard disk and on the supplied DVDs (see Installation DVD of
ServerView Suite - ServerView Software Products).

You will find further information about the BIOS setup in the "D3034 BIOS Setup
Utility for PRIMERGY RX100 S7" manual.

I PRIMERGY manuals are available in PDF format on the PRIMERGY

ServerView Suite DVD 2. The PRIMERGY ServerView Suite DVD 2 is
part of the PRIMERGY ServerView Suite supplied with every server.

PRIMERGY Abbreviations and Glossary can also be found on the PRIMERGY
ServerView Suite DVD 2.

Model lines for RX100 S7

There are two model lines for the RX100 S7 server:

– RX100 S7
– RX100 S7p

I For the European market:

You can identify the model line by the model name "RX100 S7p" printed
on the identification rating plate and on the ID card.

I For the Japanese market:

"RX100 S7p" is not used as the model name in the Japanese market.

You can identify the model line by the product number; The product
number "PYR10Pxxx" means RX100 S7p.

For an overview of the different features please refer to table 1 on page 15.

10 Technical Manual D3034 (RX100 S7)

Introduction

1.1 Notational conventions

The following notational conventions are used in this manual:

Text in italics indicates commands or menu items.

"Quotation marks" indicate names of chapters and terms that are being

emphasized.

Ê describes activities that must be performed in the order

shown.

V CAUTION! pay particular attention to texts marked with this symbol.

Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.

I indicates additional information, notes and tips.

D3034 (RX100 S7) Technical Manual 11

2 Important information

V CAUTION!

With the system board installed you must open the system to access the
system board. How to access the system board of your system is
described in the appropriate Upgrade and Maintenance Manual of your
server.

When handling the system board, refer to the specific notes on safety in
the Upgrade and Maintenance Manual of your server.

2.1 CE certificate of conformity

The system board complies with the requirements of the EC
directives 2004/108/EC regarding “Electromagnetic
Compatibility” and 2006/95/EC “Low Voltage Directive”. This is
indicated by the CE marking (CE = Communauté Européenne).

Compliance was tested in a typical PRIMERGY configuration.

12 Technical Manual D3034 (RX100 S7)

Important information

2.2 Environmental protection

Environmentally-friendly product design and development

This product has been designed in accordance with the Fujitsu standard for
"environmentally friendly product design and development". This means that
key factors such as durability, selection and labeling of materials, emissions,
packaging, ease of dismantling and recycling have been taken into account.

This saves resources and thus reduces the harm done to the environment.
Further information can be found at:

– http://ts.fujitsu.com/products/standard_servers/index.html (for the EMEA market)
– http://jp.fujitsu.com/platform/server/primergy/concept/ (for the Japanese

market)

Energy-saving information

Devices that do not need to be constantly switched on should be switched off
until they are needed as well as during long breaks and after completion of work.

Packaging information

This packaging information doesn’t apply to the Japanese market.

Do not throw away the packaging. You may need it later for transporting the
system. If possible, the equipment should only be transported in its original
packaging.

Information on handling consumables

Please dispose of printer consumables and batteries in accordance with the
applicable national regulations.

In accordance with EU directives, batteries must not be disposed of with
unsorted domestic waste. They can be returned free of charge to the
manufacturer, dealer or an authorized agent for recycling or disposal.

All batteries containing pollutants are marked with a symbol (a crossed-out
garbage can). They are also marked with the chemical symbol for the heavy
metal that causes them to be categorized as containing pollutants:

Cd Cadmium
Hg Mercury
Pb Lead

D3034 (RX100 S7) Technical Manual 13

Important information

Labels on plastic casing parts

Please avoid sticking your own labels on plastic parts wherever possible, since
this makes it difficult to recycle them.

Returns, recycling and disposal

Please handle returns, recycling and disposal in accordance with local
regulations.

Details regarding the return and recycling of devices and consumables within
Europe can also be found in the "Returning used devices" manual, via your local
Fujitsu branch or from our recycling center in Paderborn:

Fujitsu Technology Solutions
Recycling Center
D-33106 Paderborn

Tel. [phone]
Fax [phone]

The device must not be disposed of with domestic waste. This
device is labeled in compliance with European directive
2002/96/EC on waste electrical and electronic equipment (WEEE).

This directive sets the framework for returning and recycling used
equipment and is valid across the EU. When returning your used
device, please use the return and collection systems available to
you. Further information can be found at

http://ts.fujitsu.com/recycling.

14 Technical Manual D3034 (RX100 S7)

Important information

D3034 (RX100 S7) Technical Manual 15

3 Features

Model lines for RX100 S7

There are two model lines for the RX100 S7 server:

– RX100 S7
– RX100 S7p

The following table provides an overview of the different features:

RX100 S7 RX100 S7p

System board D3034-Axx D3034-Bxx

Processors Intel

®

XEON® E3-1200

processor series

Intel

®

Pentium® / Celeron®

processor series

Intel

®

Core™ i3-2100

processor series

Intel

®

XEON® E3-1200v2

processor series

Intel

®

Pentium® / Celeron®

processor series

Intel

®

Core™ i3

processor series

Main Memory DDR3 UDIMM with 1333 MHz

speed

up to 21 GB/s bandwidth in
dual channel mode and 10.6
GB/s in single channel mode

DDR3 UDIMM with 1600 MHz
speed

up to 25.6 GB/s bandwidth in
dual channel mode and 12.8
GB/s in single channel mode

PCI slots 1x PCIe x4 Gen 2 (internal

only for SAS controller)

1x PCIe x16 Gen 2

1x PCIe x1 Gen 2

1x PCIe x4 Gen 2 (internal
only for SAS controller)

1x PCIe x16 Gen 3

1x PCIe x1 Gen 2

Table 1: Differences between RX100 S7 and RX100 S7p

16 Technical Manual D3034 (RX100 S7)

Features

I For the European market:

You can identify the model line by the model name "RX100 S7p" printed
on the identification rating plate and on the ID card.

I For the Japanese market:

"RX100 S7p" is not used as the model name in the Japanese market.

You can identify the model line by the product number: The product
number "PYR10Pxxx" means RX100 S7p.

D3034 (RX100 S7) Technical Manual 17

Features

3.1 Overview

Processors

– one processor socket LGA 1155 (H2)
– one Intel

®

Quad-Core processor (Xeon E3-12xx or E3-12xxL) or one Intel®

Dual-Core processor (Pentium or Core-i3)

Main memory

– 4 slots for main memory; CPU supports 2 channels with 2 DIMM slots
– UDIMM (unbuffered DIMM) memory modules
– minimum memory configuration: one DIMM in DIMM1A
– maximum memory configuration: UDIMM memory modules 32 GB
– ECC multiple bit error detection and single bit error correction

Chips on the system board

– Intel

®

C202 chip set
– Gigabit Ethernet controller Intel 82574L (shared LAN)
– Gigabit Ethernet controller Intel 82579LM (standard LAN)
– 8 MB Flash BIOS
– onboard iRMC S3 Server Management Controller with integrated graphics

controller and associated management LAN connector

Internal connectors

– 1x front panel connector
– 1x power supply connector 24 pin (12V)
– 1x power connector for system fans and ODD
–1x I

2

C connector for PSU
– 4x SATA HDD connectors
– 1x SATA ODD connector
– 1x power connector 8 pin for SAS/SATA backplane
– 1x LED signaling connector for SAS/SATA backplane
–1x I

2

C signaling connector for optional LocalView Service Panel

18 Technical Manual D3034 (RX100 S7)

Features

– 1x connector for optional front VGA
– 1x connector for optional front LAN card
– 1x connector for optional TPM
– 1x connector for optional USB Flash Module (UFM)
– 1x reset connector (optional)

External connectors

– front side:

– 1x video (VGA) connector, 1x LAN connector (with optional front

VGA/LAN module)

– 2x USB 2.0 connectors

– rear side:

– 1x serial connector (COM1)
– 4x USB 2.0 connectors
– 1x video connector (VGA)
– 3x RJ45 LAN connectors

PCI slots

– 1 x PCI Express x16 slot for a riser card
– 1 x PCI Express x1 slot for a riser card
– 1 x PCI Express x4 slot for a riser card

Power management

– ACPI (states S0, S4, S5)
– 3.3 V standby power on the PCI Express slots
– on/off/sleep/wake by power button
– on/off by software
– wake by RTC, external serial connectors, LAN, PCI Express controller and

iRMC S3

– power on by power button, external serial connectors, LAN, PCI Express

controller and iRMC S3

D3034 (RX100 S7) Technical Manual 19

Features

BIOS features

– UEFI (Unified Extensible Firmware Interface)
– SMBIOS 2.5 (DMI)
– Server Hardware Design Guide
– WfM 2.0
– ACPI 2.0 support
– USB keyboard/mouse
– boot possible from:

– CD-ROM/DVD (SATA)
– hard disk (SATA, SAS, USB)

–LAN
– console redirection support
– OEM logo
– CPU, memory disable

Environmental protection

– battery in holder

Form factor

– 235.5 mm (W) x 255.5 mm (D)

CSS (Customer Self Service)

This system board supports the CSS functionality. You will find a description of
CSS functionality in the operating manual of your server.

USB Flash Module (option)

The system board can be equipped with an USB Flash Module (UFM) by the
manufacturer or by an add-on kit. The module can be used as optional memory
for software (e.g. VMware) or as a software dongle.

20 Technical Manual D3034 (RX100 S7)

Features

TPM (option)

The system board can be equipped with a TPM (Trusted Platform Module) by
the manufacturer or by an add-on kit. This module enables programs from third
party manufacturers to store key information (e.g. drive encryption using
Windows Bitlocker Drive Encryption).

The TPM is activated via the BIOS system (for more information, refer to the
BIOS manual).

V CAUTION!

– When using the TPM, note the program descriptions provided by the

third party manufacturers.

– You must also create a backup of the TPM content. To do this, follow

the third party manufacturer's instructions. Without this backup, if the

TPM or the system board is faulty you will not be able to access your

data.

– If a failure occurs, please inform your service about the TPM

activation before it takes any action, and be prepared to provide them

with your backup copies of the TPM content.

D3034 (RX100 S7) Technical Manual 21

Features

3.2 Main memory

I You will find the descriptions how to install memory modules in the

Upgrade and Maintenance Manual of your server.

Figure 1: Slots of the main memory

The assignment of the DIMM slots is:
DIMM 1A = channel A DIMM 1, DIMM 1B = channel B DIMM 1,
DIMM 2A = channel A DIMM 2, DIMM 2B = channel B DIMM 2

3.2.1 Module population

– Memory slot 1 / channel A (DIMM 1A) needs to be populated first.

– Within all channels memory slot 1 must be populated prior to slot 2.

– Install memory modules within a channel in descending order of capacity:

higher capacity in slot 1, lower capacity in slot 2.

3.2.1.1 Types of memory modules

UDIMM memory modules

Technology: DDR3 1066 / 1333 / 1600 unbuffered single rank (SR) or

dual rank (DR) UDIMM memory modules with ECC.
Support for up to 4 UDIMM memory modules.

Total memory size: up to 32 GB

SATA4

SATA2

SATA1

SATA3

PCH

iRMC S3

SATA5-ODD

Riser card (x1)

DIMM1B

DIMM2A
DIMM1A

DIMM2B

CPU

Indicate
CSS

VGA

COM1

Riser card (x4)

USB1/2

Standard
LAN

USB3/4

Slot2

Slot1

CSS

J22

Reset (PIN1),
GND (PIN2)

1

22 Technical Manual D3034 (RX100 S7)

Features

3.2.1.2 Modes of operation

Figure 2: Dual-channel symmetric and asymmetric mode

– The maximum performance can be achieved in a symmetric dual-channel

configuration. Therefore both channels have to be populated with the same
amount of memory. The DRAM device technology (1Gbit / 2Gbit) may vary
from one channel to the other.

– If the amount of memory differs between the two channels, the system board

will run in dual-channel asymmetric mode.

– Regardless of the mode, all DIMMs will run at the highest common

frequency that is allowed by the SPD Data of the DIMMs and the max. speed
of the selected configuration.

– Single-channel mode is used when 1 memory module is populated in

DIMM 1A.

Configuration per
channel

Max. speed DIMM-2 DIMM-1

1 DDR3-1333 / 1600 empty SR/DR

2 DDR3-1333 / 1600 SR/DR SR/DR

channel

A B

Dual mode

Memory size

channel

AB

Dual mode Single

mode

Dual-channel symmetric mode Dual-channel asymmetric mode

Memory size A

Memory size B

D3034 (RX100 S7) Technical Manual 23

Features

3.3 PCI slots

Figure 3: PCI slots for riser cards

Slot PCI bus Length

Slot 1 PCI Express x4

(mech. x8)

Only for modular RAID

Slot 2 PCI Express x1

(mech. x4)

Low-profile slot, maximum length 170 mm

Slot 3 PCI Express x16 Low-profile slot, maximum length 170 mm

SATA4

BP PWR

PCIE16

PCIE4 PCIE1

SATA2

SATA1

SATA3

BP SGPIO

PCH

iRMC S3

SATA5-ODD

PWR1

Riser card (x1)

DIMM1B

DIMM2A
DIMM1A

Riser card (x16)

DIMM2B

CPU

VGA

Battery

TPM

COM1

Riser card (x4)

USB1/2

Managem.
LAN

Shared
LAN

Standard
LAN

UFM

PWR2

USB3/4

FAN5

FAN4

FAN3

FAN2

FAN1

FRONT LAN

Slot3

Slot2

Slot1

FAN SYSFRONT VGA FRONT PANEL

J22

J26

Reset (PIN1),
GND (PIN2)

1

Indicate
CSS

CSS

24 Technical Manual D3034 (RX100 S7)

Features

PCI Express interrupts

Each device connected to a PCI Express can use up to four interrupt signals
depending on the functionality.

PCI Express devices send their interrupts through messages. The interrupts are
defined by the system design.

The following interrupt signals are used in the system:

Slot/device Property Interrupt signal

VGA iRMC S3 graphic PCI-INTA

LAN Intel 82574L PCI-INTA

LAN Intel 82579LM PCI-INTA

Slot 3 PCIe x16 PCI_INTA, PCI_INTB, PCI_INTC,

PCI_INTD

Slot 2 PCIe x1 PCI_INTA, PCI_INTB, PCI_INTC,

PCI_INTD

Slot 1 PCIe x4 PCI_INTA, PCI_INTB, PCI_INTC,

PCI_INTD

D3034 (RX100 S7) Technical Manual 25

Features

3.4 Screen resolution

Depending on the operating system used the screen resolutions in the following
table refer to the graphic controller on the system board. The graphic controller
is integrated in the iRMC S3 (integrated Remote Management Controller).

If you are using an external graphic controller, you will find details of supported
screen resolutions in the operating manual or technical manual supplied with
the graphic controller.

Screen resolution
(pixel)

Maximum refresh
rate (Hz)

Max. number of colours

640x480 85 32 bit

800x600 85 32 bit

1024x768 75 32 bit

1152x864 60 16 bit

1280x1024 60 24 bit

1600x1200 60 16 bit

26 Technical Manual D3034 (RX100 S7)

Features

3.5 Temperature / system monitoring

Temperature and system monitoring aim to reliably protect the computer
hardware against damage caused by overheating. In addition, any unnecessary
noise is also prevented by reducing the fan speed, and information is provided
about the system status.

The following functions are supported:

Temperature monitoring

Measurement of the processor and the system internal temperature by an
onboard temperature sensor, measurement of the ambient temperature by a
I

2

C temperature sensor, measurement of the memory temperatures by

integrated temperature sensors.

Fan monitoring

The power supply unit and system fans are monitored. Fans that are no longer
available, blocked or stuck fans are detected.

Fan control

The fans are regulated according to temperature.

Voltage monitoring

When voltage exceeds warning level high or falls below warning level low an
alert will be generated.

System Event Log (SEL)

All monitored events of the system board are signalized via the Global Error
LED or CSS LED and recorded in the System Event Log. They could be
retrieved in the BIOS Setup, iRMC S3’s Web interface or via the ServerView
Operations Manager.

PRIMERGY Local Diagnostic LEDs (LDL)

Optical signaling through the LEDs on the system board identifies defective
modules and components (CSS functionality) as well as gaining information on
the PDA (Prefailure Detection and Analysis).

D3034 (RX100 S7) Technical Manual 27

Features

3.6 Connectors and indicators

3.6.1 System board

Figure 4: Internal connectors of the system board D3034

SATA4

BP PWR

PCIE16

PCIE4 PCIE1

SATA2

SATA1

SATA3

BP SGPIO

PCH

iRMC S3

SATA5-ODD

PWR1

Riser card (x1)

DIMM1B

DIMM2A
DIMM1A

Riser card (x16)

DIMM2B

CPU

VGA

Battery

TPM

COM1

Riser card (x4)

USB1/2

Managem.
LAN

Shared
LAN

Standard
LAN

UFM

PWR2

USB3/4

FAN5

FAN4

FAN3

FAN2

FAN1

FRONT LAN

Slot3

Slot2

Slot1

FAN SYSFRONT VGA FRONT PANEL

J22

J26

Reset (PIN1),
GND (PIN2)

1

Indicate
CSS

CSS

/

1

23 40

5

6

=>; 7:<?

89

28 Technical Manual D3034 (RX100 S7)

Features

No. Print Description

1 TPM Connector for optional TPM

2 FRONT LAN Connector for optional front LAN card

3PWR2 I

2

C connector for PSU

4 BP PWR Power connector for SAS/SATA backplane

5 BP SGPIO LED signaling connector for SAS/SATA backplane

6 PWR1 Power supply connector 12V

7 SATA 5 ODD SATA connector for optical drive

8CSS I

2

C signaling connector for optional LocalView

Service Panel

9 FAN SYS Power connector for system fans and ODD

10 Reset, GND Reset connector (optional)

11 FRONT PANEL Front panel connector

12 SATA 3 SATA HDD connector

13 FRONT VGA Connector for optional front VGA

14 SATA 1 SATA HDD connector

15 SATA 4 SATA HDD connector

16 SATA 2 SATA HDD connector

17 UFM Connector for optional USB Flash Module (UFM)

D3034 (RX100 S7) Technical Manual 29

Features

Figure 5: Indicators on the system board and CSS indicate button

LEDs A, B and C are visible from outside on the rear of the server. All the other
LEDs are only visible, if the cover of the server has been opened.

If the server has been powered off (power-plugs must be disconnected) it is
possible to indicate the faulty component by pressing the CSS indicate button.

No. Description

1 CSS indicate button

SATA4

BP PWR

PCIE16

PCIE4 PCIE1

SATA2

SATA1

SATA3

BP SGPIO

PCH

iRMC S3

SATA5-ODD

PWR1

Riser card (x1)

DIMM1B

DIMM2A
DIMM1A

Riser card (x16)

DIMM2B

CPU

VGA

Battery

TPM

COM1

Riser card (x4)

USB1/2

Managem.
LAN

Shared
LAN

Standard
LAN

UFM

PWR2

USB3/4

FAN5

FAN4

FAN3

FAN2

FAN1

FRONT LAN

Slot3

Slot2

Slot1

FAN SYSFRONT VGA FRONT PANEL

J22

J26

Reset (PIN1),
GND (PIN2)

1

0

Indicate
CSS

CSS

30 Technical Manual D3034 (RX100 S7)

Features

The LEDs have the following meaning:

LED Indicator Meaning

A - CSS
(Customer Self
Service)

off no error (CSS component)

yellow on indicates a prefailure (CSS component)

yellow flashing indicates a failure (CSS component)

B - GEL
(Global Error
LED)

off no error (non CSS component)

orange on indicates a prefailure (non CSS

component)

orange flashing indicates a failure of a non CSS

component.
Reasons for a failure may be:

– over temperature measured by one of

the sensors
– sensor is defective
–CPU error
– software detected an error

C - Identification blue on server is identified via the ServerView

Operations Manager or by ID button

blue flashing local monitor off

D - Memory off memory module running

orange on memory module failure

E - CPU off CPU okay

orange on CPU failure

F - System fan off fan running

orange on fan failure

G - PCI card off PCI card okay

orange on PCI card failure (PCI card installed on riser

card)

H - iRMC off iRMC S3 inactive

green flashing iRMC S3 okay

D3034 (RX100 S7) Technical Manual 31

Features

3.6.2 Connector panel

Figure 6: Connector panel

The serial connector COM1 can be used as default interface or to communicate
with the iRMC S3.

LAN connectors

The system board is equipped with a Gigabit Ethernet Controller type Intel
82574L (shared LAN) and a Gigabit Ethernet Controller type 82579LM
(standard LAN). The LAN controllers support transmission rates of 10 Mbit/s,
100 Mbit/s and 1 Gbit/s.

The shared LAN controller also supports WOL functionality by means of Magic
Packet™. It is also possible to start a system via a LAN without a separate boot
hard disk drive.

No. Description

1 Global error indicator (orange), CSS indicator (yellow), ID indicator

(blue); (description see preceding section)

2 Management LAN connector (for iRMC S3 server management function)

3 Shared LAN connector (for WOL/PXE/iSCSI function)

4 Serial connector COM1

5 Video connector (VGA)

6 2x USB connectors

7 Standard LAN connector

8 2x USB connectors

/ 0 1 2 3 4 5 6

32 Technical Manual D3034 (RX100 S7)

Features

The separate management LAN connector is used as a management interface
(iRMC S3) and is prepared for operation with the Remote Management.
Optionally the shared LAN connector can also be used for iRMC S3 server
management.

Each LAN connector has two LEDs which display the speed of the connection
and its status:

Figure 7: LAN LEDs

LED Indicator Description

1 LAN speed Steady yellow signal in the event of a LAN transfer

rate of 1 Gbit/s

Steady green signal in the event of a LAN transfer
rate of 100 Mbit/s.

Remains dark in the event of a LAN transfer rate of
10 Mbit/s.

2LAN

link/transfer

Steady green signal when a LAN connection exists.

Remains dark when no LAN connection exists.

Flashes green when LAN transfer takes place.

/0 /0 /0

D3034 (RX100 S7) Technical Manual 33

Features

3.7 Settings

3.7.1 Jumper

Figure 8: Jumper

Jumper Print Setting

J22 PASSWORD SKIP open: normal operation (default)

short: clear password and apply the default
BIOS settings

J26 BIOS RECOVER 1-2 normal operation (default)

2-3 recovery mode

SATA4

SATA2

SATA1

SATA3

PCH

SATA5-ODD

Riser card (x1)

DIMM1B

DIMM2A
DIMM1A

DIMM2B

VGA

Riser card (x4)

USB1/2

Standard
LAN

UFM

USB3/4

Slot2

Slot1

FAN SYSFRONT VGA FRONT PANEL

J22

J26

Reset (PIN1),
GND (PIN2)

1

Default:

J22

J26

Indicate
CSS

CSS

34 Technical Manual D3034 (RX100 S7)

Features