Fuji Electric PB-F1-15 Operating Manual
Installation Manual
Mounting Adapter for External Cooling "PB-F1/E1"
㩷
Thank you for purchasing the Mounting Adapter for External Cooling PB-F1/E1. This adapter allows you to mount your
FRENIC-Eco/FRENIC-Multi series of inverters on the panel in such a way that the heat sink assembly may be exposed to the outside.
Using this adapter greatly reduces heat radiated or spread inside the panel enclosure.
• Do not touch the sharp edges of metallic components.
Doing so could cause injuries.
• Do not use screws other than the ones included in the kit.
Doing so could cause a drop of the inverter and injuries.
• Do not support the inverter by the terminal cover or the front cover during moving or transporting the inverter.
Doing so could cause a drop of the inverter and injuries.
• Prevent lint, paper fibers, sawdust, dust, metallic chips, or other foreign materials from getting into the inverter or from
accumulating on the heat sink.
Otherwise, a fire or an accident might result.
• Do not install or operate an inverter that is damaged or lacking parts.
Doing so could cause fire, an accident, or injuries.
1. Check that:
(1) All the component parts of the adapter including the screws and
nuts are contained in the package. Types of screws and nuts vary
depending on the model of the adapter. See "2. Mounting Adapter
Models and Applicable Inverter Models" for details.
(2) The adapter is not damaged during transportation - no dents, bends,
warp, or scratches.
(3) The adapter is the model you ordered and the model name of the
adapter printed on the nameplate (shown at the right) matches your
inverter model (see the table on the next page).
If you suspect the product is not working properly or if you have any
questions about your product, contact your Fuji Electric representative.
- 1 -
2. Mounting Adapter Models and Applicable Inverter Models
Model Name of Adapter and Accompanying Screws and Nuts Applicable Inverter Models
PB-F1-5.5
PB-F1-15
PB-F1-30
A set of upper and lower
adapter plates
1 adapter plate
1 adapter plate
4 (M5 u 8) cross recessed head tapping
screws
6 (M6 u 15) cross recessed pan head
screws with captive washer
6 (M6) hexagon nuts
6 (M8 u 25) cross recessed pan head
screws with captive washer
4 (M8) hexagon nuts
6 (M8 u 25) cross recessed pan head
screws with captive washer
4 (M8) hexagon nuts
FRENIC-Eco
FRENIC-Eco
FRENIC-Multi
FRENIC-Eco
FRN001F1S-2U
FRN002F1S-2U
FRN002F1S-2U
FRN005F1S-2U
FRN007F1S-2U
FRN001F1S-4U
FRN002F1S-4U
FRN003F1S-4U
FRN005F1S-4U
FRN007F1S-4U
FRN010F1S-2U
FRN015F1S-2U
FRN020F1S-2U
FRN010F1S-4U
FRN015F1S-4U
FRN020F1S-4U
FRN015E1S-2U
FRN020E1S-2U
FRN015E1S-4U
FRN020E1S-4U
FRN025F1S-2U
FRN030F1S-2U
FRN040F1S-2U
FRN025F1S-4U
FRN030F1S-4U
FRN040F1S-4U
PB-E1-7.5
6 (M5 u 15) cross recessed pan head
screws with captive washer
1 adapter plate
4 (M5) hexagon nuts
3. Cutting a Hole through the Panel
Cut a mounting hole in the shape according to the model dimensions as shown below.
PB-F1-5.5
PB-F1-15 PB-F1-30 PB-E1-7.5
FRENIC-Multi
FRN007E1S-2U
FRN010E1S-2U
FRN007E1S-4U
FRN010E1S-4U
(Unit: mm)
4 (M5) screw
6 (M6) screw
holes
(or holes of
7.5 mm dia.)
4 (M8) screw
holes
(or holes of
10 mm dia.)
- 2 -
4 (M8) screw
holes
(or holes of
10 mm dia.)
holes
(or holes of
6.5 mm dia.)
Loading...