Fuji Electric OPC-ALL-115V Operating Manual

Models: OPC-ALL-115V

INSTRUCTION SHEET

Thank you for purchasing OPC-ALL-115V model. Please read the instruction sheet and thoroughly familiarize yourself with the functions and characteristics of the products before use.

Specifications:

Inverter Side:

Digital Inputs: 4 DC inputs (24VDC) Input : 24VDC, 12mA per channel

Parameters 4DC Inputs (24VDC) Input Impedance: 2.88K ohm Min. ON voltage: 18VDC Max. OFF voltage:1.2VDC Turn ON time: 10msec max Turn OFF time: 5msec max

Digital Outputs: 8 Relay outputs Output: 24VDC, 20mA per channel

General: Operating Temp.: 0 to 60°C Storage Temp.: -20 to 80°C Operating Humidity:10% to 90% (Non condensing)

Dimensions and Panel Mounting:

145mm

2. Din rail installation: a. Mount the DIN rail to your mounting surface. b. Align the unit to the mounting plate and snap the unit into place. c. Hook the top slot of the mounting plate over the DIN rail. d. While pressing the unit against the rail, snap the unit into place.

BACK VIEW

e-Frontrunners

OPC-ALL-115VPART#:

S/N.: CIWWYYXXXXX

Made in India

User Side:

Digital Inputs: 8 AC inputs (115V) Input: 115VAC, 8mA per channel

92mm

Parameters 8 AC Inputs (115V) Input Impedance: 6.5K ohm Min. ON voltage: 96VAC Max. OFF voltage: 36VAC Turn ON time: 15msec max Turn OFF time: 10msec max

Digital Outputs: 4 Relay outputs. Output: 250VAC, 5A / 24VDC, 5A per

Channel

This unit can be mounted on DIN rail slider as well as can be rest on mounting plate:

1. For mounting plate installation: A) Drill hole into your mounting surface (#36 drill

BACK VIEW

e-Frontrunners

OPC-ALL-115VPART#:

S/N.: CIWWYYXXXXX

Made in India

recommended). B) Align the unit to the mounting plate. C) Fasten the mounting plate to your surface with four screws.

Quick Start Manual Doc. No.: ; Ver.: 1.00QS-OPC-ALL-115-1010 Renu Electronics Pvt. Ltd. Pub.: 10/2010

Inverter Side:User Side:

COM1

NO1

L O A D

COM2

COM3

NO2

L O A D

COM4

NO3

NO4

115 VAC

Input: User can connect 8 AC Inputs (115VAC) as input to respective relay coil. I1 to I8 stands for Input 1 to 8 (Phase) where as N stands for Neutral that is common for all Inputs

Each Relay can be trigger by applying minimum 96VAC.

Input (115VAC) Status LED Output

RED I1 L5 X1 I2 L6 X2 I3 L7 X3 I4 L8 X4 I5 L9 X5 I6 L10 X6 I7 L11 X7 I8 L12 X8

A red LED indication is provided for each Relay status.

Note: Status LED's will glow only if load is connected to X1-X8, as LED's are connected in series with load at each AC relay output side.

Y2Y1+24V

24VDC

INVERTER OUTPUT

COM

INVERTER SIDE

24VDC

COM

X4 X3

INVERTER INPUT

I/P1I/P3I/P5I/P7

I/P2I/P4I/P6I/P8

Input: Inverter outputs can be applied to 4 DC Inputs (24VDC) as input to respective relay coil. Y1 to Y4 stands for Input 1 to 4 (Negative) where as +24V is common for all four Inputs.

Each Relay can be trigger by applying minimum 18VDC.

A green LED indication is provided for each Relay status.

Input (24VDC) Status LED Output

GREEN Y1 L1 COM1: NO1 Y2 L2 COM2: NO2 Y3 L3 COM3: NO3 Y4 L4 COM4: NO4

Output: X1 to X8 are Inputs for Inverter, which has +24VDC as Inputs for Inverter side. Where as three COM terminals are provides as a common at Inverter side.

Technical Support:

For Technical support please contact factory along with the unit serial number and revision number written on the address sticker of the unit. Also provide information of the application used.

MANUAL REVISIONS:

Output: User can connect load to 4 Relay outputs. This 4 Relay can be driven by Inverter output (24VDC).

Quick Start Manual

ELECTRONICS PVT. LTD.

Doc. No.: ; Ver.: 1.00QS-OPC-ALL-115V-1010

Rev. No. Doc. No. Date Description

1.00 QS-OPC-ALL-115-1010 08/10/10 First Draft

Renu Electronics Pvt. Ltd.

Pub.: 10/2010