IPC PSU FSP1200-50AAG
DESCRIPTION
FSP1200-50AAG is an industrial level of switching power supply. The power supply comes to offer the total power capacity up to 1200 Watts, and uses unique active PFC (Power Factor Correction) circuit design with its high-load electrical components, makes it to be perfectly used in an industrial environment. In addition, with its full range of input and output electrical features, the power supply is ideally the best choice for server, workstation, communication or any other automation applications to use. The product also complies with the latest safety and EMC standards, which is perfectly to meet various regulations worldwide.
APPLICATION
For standard, advanced workstation, server and industrial power system.
FEATURES
85 Plus Gold
Low Ripple & Noise
Output over voltage protection Short circuit protection on all outputs Resettable power shut down
INTERNAL 4 cm fan 100% burn-in under high ambient temperature(50 )
Vacuum-impregnated transformer
MTBF:100K hours at 25
100% Hi-pot tested Line input fuse protection
WATTAGE
Wattage: 1200W
DIMENSION
Dimension: 190mm(L) x 150mm(W) x
86mm(H)
PRODUCT HIGHLIGHT
Efficiency Level: |
80 Plus Gold |
Altitude: |
5000M |
INPUT SPECIFICATION
Input Range: |
90-264 Vac |
|
Input Frequency: |
47-63 Hz |
|
Input Current: |
115V@ |
12.0 Amps-rms maximum |
|
230V@ |
6.0 Amps-rms maximum |
GENERAL SPECIFICATION
Effciency: |
90% 230VAC |
Voltage |
+3.3V, +12V, +5V, +5SB: ±5% |
Regulation: |
-12V: ±10% |
*Output Voltage and Current Rating
SAFETY STANDARD APPAOVAL
OUTPUT SPECIFICATION
Hold up Time: |
115V/60Hz 17mSec. |
|
Minimum@100% Load, |
|
230V/50Hz 17mSec. |
Ouput Voltage |
Minimum,@100% Load |
+3.3Vdc output : +3.76 Vdc |
|
Regulation: |
minimum, + 4.8Vdc |
|
maximum |
|
+5Vdc output : +5.75 Vdc |
|
minimum, + 7.0Vdc |
|
maximum |
|
+12Vdc output : +13.5 Vdc |
|
minimum, + 15.5Vdc |
Output Rise Time: |
maximum |
115V-rms/230V-rms 5V |
|
|
20ms Maximum |
|
115V-rms/230V-rms 12V |
Ripple & Noise: |
20ms Maximum |
3.3V:50mV p-p |
|
|
5V:50mV p-p |
|
12V1:120mV p-p |
|
-12V:120mV p-p |
|
5Vsb:50mV p-p |
ENVIRONMENTAL SPECIFICATION
TEMP.Range: |
Storage Temperature: - |
MTBF: |
20°C to + 80 |
The power supply have a |
|
|
minimum predicted |
|
MTBF(MIL-HDBK-217) of |
|
100,000 hours of continuous |
|
operation at 25 , |
|
maximum-output load, and |
|
nominal AC inout voltage |
|
+3.3V |
+5V |
+12V1 |
-12V |
+5Vsb |
Ripple-Noise(R-P) mV |
50mV |
50mV |
120mV |
120mV |
50mV |
Regulation Load % |
±5% |
±5% |
±5% |
±10% |
±5% |
Output Max.(A) |
30A |
30A |
100A |
0.8A |
4A |
Output Min.(A) |
0A |
0.1A |
0.2A |
0A |
0A |
NOTES
Maximum continuous total DC output power should not exceed 1200W.
Maximum continuous combined load on +3.3DC and +5VDC outputs shall not exceed 150W.
Ripple and noise measurements shall be made under all specified load conditions through a single pole low pass filter with 20MHz cutoff frequency. Outputs shall bypassed at the connector with a 0.1uF ceramic disk capacitor and a 10uF electrolytic capacitor to simulate system loading.
This content is subject to change, please refer to specification for more detail.
FSP reserve the right to change the content without prior notice
Loading...