Frymaster FPPH417TC User Manual

ELECTRIC FRYERS

Service & Parts Manual

PRO SERIES

Frymaster, a member of the Commercial Food Equipment Service Association, recommends
using CFESA Certified Technicians.

24-Hour Service Hotline [phone]

*8195990*

MAR 2008

NOTICE

IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS

EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY

FROM FRYMA ST ER/DEAN, OR ANY OF ITS AU THORIZED SERV IC E CENTERS, AND /OR THE

PART BEING USED IS MODIFIED FROM IT S ORIGINAL CONFIGURATION, TH IS WARRANTY WILL

BE VOID. FURTHER, FRYMASTER AND DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR

ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE

DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INST ALLATION OF A N Y

MODIFIED PART AND/OR PART RECEIVE D FROM A N UNA UT HORIZED SERVICE CENTER.

DANGER

Copper wire suitable for at least 167°F (75°C) must be used for power connections.

DANGER

The electrical power supply for this appliance must be the same as indicated on the

rating and serial number plate located on the inside of the fryer door.

DANGER

This appliance must be connected to the voltage and phase as specified on the rating

and serial number plate located on the inside of the fryer door.

DANGER

All wiring connections for this appliance must be made in accordance with the wiring
diagrams furnished with the equipment. Wiring diagrams are located on the inside of

the fryer door.

DANGER

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WARNING

Do not attach accessories to this fryer unless fryer is secured from tipping. Personal

injury may result.

WARNING

Frymaster fryers equipped with legs are for permanent installations. Fryers fitted with

legs must be lifted during movement to avoid damage and possible bodily injury. For a

moveable or portable installation, Frymaster optional equipment casters must be used.

Questions? Call 1-800-551-8633

WARNING

Do not use water jets to clean this equipment.

DANGER
All wiring connections for this appliance must be made in accordance with the wiring
diagrams furnished with the equipment. Wiring diagrams are located on the inside of

the fryer door.

WARNING

This equipment is intended for indoor use only. Do not install or operate this

equipment in outdoor areas.

i

ELECTRICAL POWER SPECIFICATIONS

WIRE

kW VOLTAGE PHASE

14 208 3 3 6 16 39 39 39
14 240 3 3 6 16 34 34 34
14 480 3 3 8 10 17 17 17
14 220/380 3 4 6 16 21 21 21
14 240/415 3 4 6 16 20 20 21
14 230/400 3 4 6 16 21 21 21

ALL

EPRI 14kW

(SOLID STATE)

17 208 3 3 6 16 48 48 48
17 240 3 3 6 16 41 41 41
17 480 3 3 6 16 21 21 21
17 220/380 3 4 6 16 26 26 26
17 240/415 3 4 6 16 24 24 24
17 230/400 3 4 6 16 25 25 25

ALL

EPRI 17kW

(SOLID STATE)

22 208 3 3 4 25 61 61 61
22 240 3 3 4 25 53 53 53
22 480 3 3 6 16 27 27 27
22 220/380 3 4 6 16 34 34 34
22 240/415 3 4 6 16 31 31 31
22 230/400 3 4 6 16 32 32 32

208 3 3 6 16 39 39 39

240 3 3 6 16 34 34 34
220/380 3 4 6 16 21 21 21
240/415 3 4 6 16 20 20 20

208 3 3 6 16 48 48 48

240 3 3 6 16 41 41 41
220/380 3 4 6 16 26 26 26
240/415 3 4 6 16 24 24 24

SERVICE

MINIMUM SIZE AMPS PER LEG

AWG mm

2

L1 L2 L3

ii

TABLE OF CONTENTS

Page

CAUTIONARY STATEMENTS i
ELECTRICAL POWER SPECIFICATIONS ii
CHAPTER 1 – SERVICE PROCEDURES 1-1

1.1 General 1-1

1.2 Replacing a Controller 1-1

1.3 Replacing Component Box Components 1-2

1.4 Replacing a Temperature Probe or High-Limit Thermostat 1-3

1.5 Replacing a Heating Element 1-5

1.6 Replacing Contactor Box Components 1-6

1.7 Replacing a Frypot 1-7

1.8 Built-in Filtration System Service Procedures 1-8

1.9 Basket Lift Service Procedures 1-12

1.10 Interface Board Diagnostic Charts 1-15

1.11 Wiring Diagrams 1-16

CHAPTER 2 – PARTS LIST 2-1

2.1 Accessories 2-1

2.2 Basket Lift Assembly and Associated Parts 2-2

2.3 Cabinetry 2-4

2.4 Drain System Components 2-8

2.5 Electronics and Wiring Components 2-16

2.6 Filtration System Components 2-28

2.7 Frypot Assemblies and Associated Parts 2-31

2.8 Oil Return System Components 2-33

PRO SERIES ELECTRIC FRYERS

CHAPTER 1: SERVICE PROCEDURES

1.1 General

Before performing any maintenance on your Frymaster fryer, disconnect the fryer from the electrical
power supply.

When electrical wires are disconnected, it is recommended that they be marked in such a way as to
facilitate re-assembly.

1.2 Replacing a Controller

1. Before removing controllers from Euro-look models (round top-cap and drains), slide the metal

bezel up to release the bottom tabs; then, remove it.

2. Remove the two screws from the upper corners of the control panel. The control panel is hinged

at the bottom and swings open from the top.

Remove screws in upper

corners of control panel and

swing control panel down.

3. Unplug the wiring harness from the connector on the back of the controller and disconnect the

grounding wire from terminal adjacent to the connector. Remove the control panel assembly by
lifting it from the hinged slots in the control panel frame.

1-1

15-Pin Connecto

r

Ground Wire Terminal

4. Remove the controller from the control panel assembly and install the replacement controller.

Reinstall the control panel assembly by reversing steps 1 and 2.

1.3 Replacing Component Box Components

1. Remove the two screws from the upper corners of the control panel and allow the control panel

to swing down (see steps 1 and 2 of section 1.2 on preceding page).

2. Unplug the wiring harness from the 15-pin connector on the interface board and disconnect the

grounding wire from terminal adjacent to the 15-pin connector on the back of the controller.
Remove the control panel assembly by lifting it from the hinge slots in the control panel frame.

3. Disconnect the wiring from the component to be replaced, being sure to make a note of where

each wire was connected.

NOTE: If replacing the interface board, connectors J1 and J2 must also be disconnected from

the 12-pin connectors on the rear of the component box, directly behind the interface board.

4. Dismount the component to be replaced and install the new component, being sure that any

required spacers, insulation, washers, etc. are in place.

NOTE: If more room to work is required, the control panel frame and top cap assembly may be

removed by removing the hex head screws that secure it to the fryer cabinet (see illustration
below). If this option is chosen, all control panel assemblies must be removed per steps 1 and 2
above. The cover plate on the lower front of the component box may also be removed if desired.

Removing the component box itself from the fryer is not recommended due to the difficulty
involved in disconnecting and reconnecting the oil-return valve rods, which pass through
openings in the component box.

1-2

Remove thes e three
sc rews at each end.

Remove thes e two scr ews
fr om th e center sup port s.

Removing the Contr ol Panel Frame and Top Cap Assembly

5. Reconnect the wiring disconnected in step 3, referring to your notes and the wiring diagrams on

the fryer door to ensure that the connections are properly made. Also, verify that no other wiring
was disconnected accidentally during the replacement process.

6. Reverse steps 1 and 2 to complete the replacement and return the fryer to service.

1.4 Replacing a Temperature Probe or High-Limit Thermostat

1. Remove the filter pan and lid from the unit. Drain the frypots into a Shortening Disposal Unit

(SDU) or other appropriate metal container.

DANGER

DO NOT drain more than one full frypot or two split frypots into the SDU at one time.

2. Disconnect the fryer from the electrical power supply and reposition it to gain access to the rear

of the fryer.

3. Remove the tilt housing and back panels from the fryer. The tilt housing must be removed first in

order to remove the upper back panel. To remove the tilt housing, raise the elements and allow
them to rest on the basket support racks as shown in the photo below.

1-3

Next, remove the hex head screws from the rear edge of the housing. The housing can then be
lifted straight up and off the fryer. Lift up on the upper back panel to disengage the tabs on its
upper corners from the cutouts in the fryer frame.

4. Disconnect the wire harness at connector C6 and, using a pin pusher, disconnect the probe leads

or high-limit leads from the connector.

5. If replacing a temperature probe, remove the screw securing the probe bracket to the element

and slide the bracket off the element and probe. Pull the probe out of the tilt housing assembly,
install the replacement probe, and reattach the element bracket. Secure the upper portion of the
probe with a replacement metal wire tie.

Probe Leads

Probe Bracket

Metal Wire Tie

If replacing a high-limit thermostat, unscrew the thermostat to be replaced. Apply Loctite

™

PST

567 or equivalent sealant to the threads of the replacement and screw it securely into the frypot.

6. If a temperature probe was replaced, insert the probe leads into the connector (see left

illustration below). For full-vat units or the left half (as viewed from the rear of the fryer) of a
dual-vat unit, the red lead goes into position 6 and the white into position 7. For the right half of
a dual-vat unit (as viewed from the rear of the fryer), the red lead goes into position 12 and the
white into position 13.

Rib marks Positi on 1

13

7

6

12

Probe Lead Position s High-Limit Lead Pos itions

10

4

11

5

If a high-limit thermostat was replaced, insert the leads into the connector (see right illustration

above). For full-vat units or the left half of a dual-vat unit (as viewed from the rear of the fryer),
the leads go into positions 4 and 5 of the connector. For the right half of a dual-vat unit (as
viewed from the rear of the fryer), the leads go into positions 10 and 11. In either case, polarity
does not matter.

7. Reinstall the back panels and tilt housing to complete the installation, then reverse steps 1 and 2

to return the fryer to service.

1-4

1.5 Replacing a Heating Element

1. Perform steps 1-3 of section 1.4, Replacing a Temperature Probe.

2. On dual-vat fryers, and on full-vat fryers where the temperature probe is attached to the element

being replaced, disconnect the wire harness containing the probe wiring (connector C6). Using a
pin pusher, disconnect the probe wires from the connector.

3. On the front of the contactor box, disconnect the 6-pin connector for the left element (as viewed

from the front of the fryer) or the 9-pin connector for the right element and pull the harness out
through the rear of the fryer. Press in on the tabs on each side of the connector while pulling
outward on the free end to extend the connector and release the element leads (see photo below).
Pull the leads out of the connector and out of the plastic wire loom.

4. Raise the element to the full up position and disconnect the element springs.

5. Remove the nuts and machine screws that secure the element to the tilt plate assembly and pull

the element out of the frypot. NOTE: Full-vat elements consist of two dual-vat elements

clamped together. For full-vat units, remove the element clamps before removing the nuts and
machine screws that secure the element to the tilt plate assembly.

6. If applicable, recover the probe bracket and probe from the element being replaced and install

them on the replacement element, then install the replacement element in the frypot, securing it
with the nuts and screws removed in Step 5.

7. Route the element leads through the wire loom to prevent chafing and press the pins into the

connector in accordance with the diagram below, then close the connector to lock the leads in

place. NOTE: It is critical that the wires be routed through the loom to prevent chafing.

Pip marks Position 1

14253

14253

6

5L 4L6L 1L2L3L

6

789

5R 4R6R 1R2R3R

1-5

8. Insert the element connector into the receptacle on the front of the contactor box, ensuring that

the latches lock.

9. If disconnected in step 2, insert the temperature probe leads into the wiring harness connector

(see illustration below). For full-vat units or the right half of a dual-vat unit, the red lead goes
into position 6 and the white into position 7. For the left half of a dual-vat unit, the red lead goes

into position 12 and the white into position 13. NOTE: Right and left refer to the fryer as

viewed from the rear.

13

7

Rib marks Position 1

6

12

10. If disconnected in step 2, reconnect connector C6 of the wiring harness.

11. Reconnect the element springs and lower the element back down onto the basket rack.

12. Reinstall the tilt housing and back panels, reposition the fryer under the exhaust hood, and

reconnect it to the electrical power supply.

1.6 Replacing Contactor Box Components

1. If replacing a contactor box above the built-in filter system, remove the filter pan and lid from

the unit. Drain the frypots into a Shortening Disposal Unit (SDU) or other appropriate metal
container. If replacing a contactor box in a non-filter unit, drain the frypot above the box into a
Shortening Disposal Unit (SDU) or other appropriate metal container.

DANGER

DO NOT drain more than one full frypot or two split frypots into the SDU at one time.

2. Disconnect the fryer from the electrical power supply.

3. Unplug the wiring harnesses from the contactor box to be serviced.

4. Remove the two screws that secure the box in place. NOTE: If you remove the screws from

both boxes at the same time, the boxes will jam against each other and neither can be removed.

Remove these screws to dismount the left c ontactor box.
The right contactor box is secured in a similar manner.

1-6

5. Carefully lower the box to the floor and pull it out the front of the fryer. Remove the top cover

to access contactors and other components.

6. After performing necessary service, reverse steps 1-5 to return the fryer to operation.

1.7 Replacing a Frypot

1. Drain the frypot into the filter pan or, if replacing a frypot over the filter system, into a

Shortening Disposal Unit (SDU) or other appropriate metal container. If replacing a frypot over
the filter system, remove the filter pan and lid from the unit.

DANGER

DO NOT drain more than one full frypot or two split frypots into the SDU at one time.

2. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the

front and rear.

3. On Euro-look models, slide the metal bezel up to release the bottom tabs; then, remove it.

4. On all models, remove the two screws from the upper corners of the control panels and allow

them to swing down (see illustration and photo on page 1-1).

5. Unplug the wiring harnesses and ground wires from the backs of the controllers. Remove the

controllers by lifting them from the hinge slots in the control panel frame.

6. Remove the tilt housing and back panels from the fryer. The tilt housing must be removed first in

order to remove the upper back panel. To remove the tilt housing, raise the elements and allow
them to rest on the basket support racks (see photo on page 1-3).

Next, remove the hex head screws from the rear edge of the housing. The housing can then be
lifted straight up and off the fryer. Lift up on the upper back panel to disengage the tabs on its
upper corners from the cutouts in the fryer frame.

7. Dismount the top cap by removing the hex head screws at each end that secure it to the control

panel frame.

8. Remove the hex head screw that secures the front of the frypot to the cabinet cross brace.

9. Remove the top-connecting strip that covers the joint with the adjacent frypot.

10. On standard models, unscrew the Teflon vent/vacuum-breaker tube fitting, open the drain tube

cleanout covers, unscrew the retainer nuts from the drain valve nipples, and remove the tube
assembly from the fryer.

On Euro-look models, unscrew the Teflon vent/vacuum-breaker tube fitting, unscrew the nut

located on the front of each section of drain tube, and remove the tube assembly from the fryer.

11. Remove the covers from the drain safety switch(es) and disconnect the switch wiring at the

switch(es).

1-7

12. At the rear of the fryer, unplug the C6 connector and, using a pin pusher, disconnect the high-

limit thermostat leads.

13. Disconnect the oil return flexline(s) at the frypot end(s).

14. Raise the elements to the “up” position and disconnect the element springs.

15. Remove the machine screws and nuts that secure the tilt plate and element assembly to the

frypot. Carefully lift the tilt plate and element assembly from the frypot and secure it to the cross
brace on the rear of the fryer with wire ties or tape.

16. Carefully lift the frypot from the fryer and place it upside down on a stable work surface.

17. Recover the drain valve(s), oil return flexline connection fitting(s), and high-limit thermostat(s)

from the frypot. Apply Loctite™ PST 567 or equivalent sealant to the threads of the recovered
parts and install them in the replacement frypot.

18. Carefully lower the replacement frypot into the fryer. Reinstall the hex head screw removed in

step 7 to attach the frypot to the fryer.

19. Position the tilt housing and element assembly in the frypot and reinstall the machine screws and

nuts removed in step 14.

20. Reconnect the oil return flexlines to the frypot, and replace aluminum tape, if necessary, to

secure heater strips to the flexlines.

21. Insert the high-limit thermostat leads disconnected in step 11 (see illustration on page 1-4 for pin

positions).

22. Reconnect the drain safety switch wiring to the switch(es) in accordance with the diagram below

then reinstall the switch covers.

RIGHT

58C BLK

57C RED

55C BLK

56C RED

DRAIN SAFETY SWITCH

LEFT

DRAIN SAFETY SWITCH

(DUAL-VAT ONLY)

23. Reinstall the drain tube assembly.

24. Reinstall the tilt housing and back panels, top cap, and top connecting strip.

25. Reinstall controllers in the control panel frame and reconnect the wiring harnesses and ground

wires.

26. Reposition the fryer under the exhaust hood and reconnect it to the electrical power supply.

1-8

1.8 Built-in Filtration System Service Procedures

1.8.1 Filtration System Problem Resolution

One of the most common causes of filtration problems is placing the filter paper on the bottom of the
filter pan rather than over the filter screen.

CAUTION

Ensure that filter screen is in place prior to filter paper placement and filter pump

operation. Improper screen placement is the primary cause of filtration system

malfunction.

When the complaint is “the pump is running, but no oil is being filtered,” check the installation of
the filter paper and ensure that the correct size is being used.

If the pump motor overheats, the thermal overload will trip and the motor will not start until it is
reset. If the pump motor does not start, press the red reset switch (button) located on the rear of the
motor at the front of the fryer.

If the pump starts after resetting the thermal overload switch, then something is causing the motor to
overheat. A major cause of overheating is when several frypots are filtered sequentially, thus
overheating the pump and motor. Allow the pump motor to cool at least 30 minutes before resuming
operation. Pump overheating can be caused
by:

Sediment Particle

• Solidified shortening in the pan or

filter lines, or

• Attempting to filter unheated oil

(cold oil is more viscous,
overloading the pump motor and
causing it to overheat).

If the motor runs but the pump does not,
there is a blockage in the pump. Incorrectly
sized or installed paper/pads will allow food
particles and sediment to pass through the
filter pan and into the pump. When
sediment enters the pump, the gears bind,
causing the motor to overload, again
tripping the thermal overload. Shortening
that has solidified in the pump will also
cause it to seize, with the same result.

A pump seized by debris or hard shortening
can usually be freed by manually moving
the gears with a screwdriver or other
instrument.

Sediment Particle

Oil Flow

Up for reverse

Down for forward

1-9

Disconnect power to the filter system, remove the input plumbing from the pump, and use a
screwdriver to manually turn the gears.

● Turning the pump gears in reverse will release a hard particle.

● Turning the pump gears forward will push softer objects and solid shortening through the

pump and allow free movement of the gears.

Incorrectly sized or installed paper/pads will also allow food particles and sediment to pass through
and clog the suction tube on the bottom of the filter pan. Particles large enough to block the suction
tube may indicate that the crumb tray is not being used. Pan blockage can also occur if shortening is
left in the pan and allowed to solidify. Blockage removal can be accomplished by forcing the item
out with an auger or drain snake. Compressed air or other pressurized gases should not be used to
force out the blockage.

1.8.2 Replacing the Filter Motor, Filter Pump, and Related Components

1. Remove the filter pan and lid from the unit. Drain the frypots into a Shortening Disposal Unit

(SDU) or other appropriate metal container.

DANGER

DO NOT drain more than one full frypot or two split frypots into the SDU at one time.

2. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the

front and rear.

3. Remove the two lower back panels, unplug the wiring harnesses from the contactor boxes, and

remove the two screws that secure one of the boxes in place (it doesn’t matter which one; see

illustration on page 1-6). NOTE: If you remove the screws from both boxes at the same time,

the boxes will jam against each other and neither can be removed.

4. Carefully lower the box to the floor and pull it out the front of the fryer. Remove the remaining

box following the same procedure.

5. Disconnect the two flexlines running to the oil-return manifold at the rear of the fryer. Remove

the nut and bolt that secures the bridge to the oil-return manifold.

Disconnect Vacuum-Breaker

Disconnect Pump

Solenoid flexline here.

Solenoid flexline here.

1-10

6. Disconnect the pump suction flexline at the end of the filter pan connection.

Disconnect Pump
Suction flexline here.

7. Remove the cover plate from the front of the motor and disconnect the motor wires.

8. Unplug the 15-pin connector from the rear of the left component box and, using a pin pusher,

disconnect the solenoid valve wires (pins 4, 6, 10 and 12). NOTE: If the vacuum-breaker

solenoid valve is connected to the manifold rather than the pump, its wires (pins 4 and 6) do not
need to be disconnected.

9. Remove the two nuts and bolts that secure the front of the bridge to the cross brace and carefully

slide the bridge rearward off the cross brace until its front end can be lowered to the floor. Be

careful not to let the rear of the bridge slip off the manifold at this point. NOTE: In some early

production units, the bridge will not slide far enough to the rear to clear the front brace. In such
cases, the front brace must be removed. It is held in place by two hex head screws on each end
and a nut and bolt inside the brace near each end.

10. Get a good grip on the bridge, carefully pull it forward off the oil-return manifold, and lower the

entire assembly to the floor. Once on the floor, pull the assembly out the front of the fryer.

11. When required service has been completed, reverse steps 6-12 to reinstall the bridge. NOTE:

The black motor wires go on the top terminal, the white on the bottom. The pump solenoid valve
wires go in positions 10 and 12 of the 15-pin connector; the vacuum-breaker solenoid valve
wires go in positions 4 and 6. In both cases, polarity does not matter.

12. Once the bridge is back in place, reverse steps 4 and 5 to reinstall the contactor boxes.

13. Reconnect the unit to the electrical power supply, and verify that the pump is functioning

correctly (i.e., when a filter handle is placed in the ON position, the motor should start and there
should be strong suction at the intake fitting and outflow at the power shower or rear flush port).

14. When proper operation has been verified, reinstall the back panels and the filter pan and lid, and

return the fryer to service.

1-11

1.8.3 Replacing the Filter Transformer or Filter Relay

Remove the left controller from the fryer to expose the interior of the left component box. The filter

transformer and relay are located as shown in the illustration below. NOTE: The right component

box is identical to the left except that the filter transformer and relay are not present.

Filter

Relay

Filter

Transformer

Dual-vat conf ig ur ation illustrated. In full-vat units, left filter handle is not pr es e nt.

1.9 Basket Lift Service Procedures

Pro Series electric fryers may be equipped with automatic basket lifts. Basket lifts always come in
pairs, although each operates independently.

A modular basket lift (illustrated below) is a self-contained sub-assembly consisting of a pair of

toothed rods which support removable basket lift arms, a pair of reversible-drive gear motors, and
four microswitches. The gear motors engage the teeth of the rods, moving them up or down
depending upon the motors’ direction of rotation. The microswitches at the upper and lower limits
of movement stop the motors when the basket is in the full up or full down position.

Timing circuitry in the controller initiates and stops basket lift operation depending upon the
variables programmed by the operator. When the product button is pressed, the timing circuitry
activates a coil in the basket lift relay to supply power to the lower microswitch. The microswitches
stop the motor at the lift’s upper and lower travel limits and reverse the direction of current flow thus
reversing the motor direction.

When the product button is pushed on the computer/controller, current flows through a coil in the
basket lift relay, causing the lower circuit to be activated. The basket lift lowers, closing the
normally open upper-micro-switch. When the downward-moving rod opens the lower normally
closed microswitch, power to the motor ceases to flow. When the computer/controller times out, the
current to the relay coil is cut, allowing the upper circuit to be activated. The basket lift then raises
and re-closes the lower microswitch. When the basket lift rod clears the upper microswitch, the
microswitch reopens, power to the circuit is cut, and the motor stops. Pushing the product button
restarts the cycle.

1-12

Problems with the basket lift can be grouped into three categories:

● Binding/jamming problems

● Motor and gear problems

● Electronic problems

100-120V Configuration

208-250V Configuration

BINDING/JAMMING PROBLEMS

Noisy, jerky or erratic movement of the lifts is usually due to lack of lubrication of the rods and their
bushings. Apply a light coat of Lubriplate® or similar lightweight white grease to the rod and
bushings to correct the problem.

With the modular basket lift, another possible cause of binding is improper positioning of the motor,
which prevents the gear from correctly engaging the teeth in the rod. To correct the problem, loosen
the screws that hold the motor in place and move it forward or backward until the rod has just
enough slack to be rotated slightly.

MOTOR AND GEAR PROBLEMS

With the modular basket lift, the most likely problem to be encountered in this category is erratic
motion of the lift due to a worn drive gear. Failure to keep the lift rod and bushings properly
lubricated will cause unnecessary wear of the gear. The problem is corrected by replacing the worn
gear.

If the lift cycles correctly but fails to remain in the up position (i.e., goes up, but then slowly settles
back down into the frypot), the problem is a failed motor brake. A failed motor brake cannot be
repaired and requires replacement of the motor itself.

If power is reaching the motor but the motor fails to run, the motor is burned out and must be
replaced.

1-13

ELECTRONIC PROBLEMS

Within this category are problems associated with the relays, microswitches, capacitors, resistors,
interface board, wiring, and controls. The most common problem in this category is a lift that
continuously travels up and down. This is usually caused by a microswitch that is out of adjustment.
Troubleshooting the electronics of a modular basket lift is simply a process of verifying current flow
through the individual components up to and including the motor. Using a multimeter set to the 250
VAC range, check the connections on both sides of the component for the presence of the applied
line voltage. The schematic below and the wiring diagram on page 1-15 identify the components
and wiring connection points.

1-14

1.10 Interface Board Diagnostic Chart

The following diagram and charts provide ten quick system checks that can be performed using only
a multimeter.

Diagostic LEDs

Diagnostic LED Legend

CMP indicates power from 12V transformer
24 indicates power from 24V transformer
HI (RH) indicates output (closed) from right latch

relay

HI (LH) indicates output (closed) from left latch

relay
HT (RH) indicates output from right heat relay
HT (LH) indicates output from left heat relay
AL (RH) indicates output (open) from right latch

relay
AL (LH) indicates output (open) from left latch

relay

K1

Left
Latch
Relay

K2

Left

Heat

Relay

23

6

5
8

9

12

11

15

14

K3 K4

Relay

1
4
7

10

13

Right
Heat

Right

Latch

Relay

4

1

7

10

5

2

8

11

6

3

9

12

4

1

7

10

5

2

8

11

6

3

9

12

H

5

Modular Basket Lift Schematic

Normally Open Upper-limit

Microswitch

Test Points

J1 Left J2 Right

1 or 4

3

To computer/controller via

interface board

Basket Lift

Relay

Normally Closed Lower-limit

Microswitch

Meter Setting Test Pin Pin Results

12 VAC Power 50 VAC Scale 1 of J2 3 of J2 12-16 VAC
24 VAC Power 50 VAC Scale 2 of J2 Chassis 24-30 VAC
*Probe Resistance (RH) R X 1000 OHMS 11 of J2 12 of J2 See Chart
*Probe Resistance (LH) R X 1000 OHMS 3 of J1 2 of J1 See Chart
Hi-Limit Continuity (RH) R X 1 OHMS 7 of J2 4 of J2 0 - OHMS
Hi-Limit Continuity (LH) R X 1 OHMS 4 of J1 7 of J1 0 - OHMS
Latch Contactor Coil (RH) R X 1 OHMS 8 of J2 Chassis 3-10 OHMS
Latch Contactor Coil (LH) R X 1 OHMS 5 of J1 Chassis 3-10 OHMS
Heat Contactor Coil (RH) R X 1 OHMS 9 of J2 Chassis 18-25 OHMS
Heat Contactor Coil (LH) R X 1 OHMS 6 of J1 Chassis 18-25 OHMS

N

M

6

* Disconnect 15-Pin harness from the computer/controller before testing the probe circuit.

1-15

1.11 Wiring Diagrams
BASKET LIFT

1-16

COMPONENT WIRING

8051397D

1-17

CONTACTOR BOX – DELTA CONFIGURATION

1-18

CONTACTOR BOX – WYE CONFIGURATION

8051399C

1-19

2.1 Accessories

PRO SERIES ELECTRIC FRYERS

CHAPTER 2: PARTS LIST

1

2

6

3

4

5

7

10

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 809-0171 Thumbscrew, ¼ -20 X 1

8

9

11

3

/

-inch

8

2 810-1403 Hanger, Wireform Basket
* 809-0921 Spacer, Basket Hanger
3 803-0197 Cleanout Rod, 27-inch
4 803-0209 Brush, Frypot
5 823-1885 Connecting Strip, Frypot
6 806-3068 Cover, Full-Vat Frypot
* 806-3071 Cover, Dual-Vat Frypot
7 803-0099 Basket, Full-Vat
8 803-0271 Basket, Dual-Vat (Twin)
9 803-0122 Sediment Tray, Left Dual-Vat
* 803-0123 Sediment Tray, Right Dual-Vat

* 803-0113 Sediment Tray, Full-Vat
10 803-0132 Rack, Full-Vat Basket Support
11 803-0106 Rack, Dual-Vat Basket Support

* 803-0002 Powder, Filter (80 1-Cup Applications)

* 803-0046 Cup, Plastic Measuring

* 803-0170 Pack, 100-Sheet Filter Paper

* Not illustrated. Use standard part.

2-1

2.2 Basket Lift Assembly and Associated Parts

33

30

29

28

34

31

32

35

17

24

26

1

25

4 17

17

15

3

20

3

14

27

216

222110

181298

175

11

2-2

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

106-1805SP Basket Lift Assembly, 200-220VAC w/Relay (Items 1-23)

1 810-1012 Rod, Basket Lift
2 813-0035 Bushing, Bronze
3 807-2513 Capacitor, 12.5 μFarad 330VAC
4 901-8499 Chassis, Left Basket Lift
5 902-8499 Chassis, Right Basket Lift
6 807-0159 Connector, 12-Pin Female
7 900-5529 Gusset, Basket Lift Motor
8 812-0442 Insulation, Microswitch

9 807-2572 Microswitch
10 806-5964SP Motor Assembly, 208-240VAC Modular Basket Lift
11 200-2942 Mount, Modular Basket Lift
12 826-1366 Nut, 4-40 Hex Keps (Pkg. of 25)
13 809-0247 Nut, 8-32 Hex Keps
14 807-1683 Relay, 12VDC
15 106-2770SP Resistor Assembly, 208-220VAC Modular Basket Lift

* 106-2771SP Resistor Assembly, 230-250VAC Modular Basket Lift
16 809-0082 Ring, Bushing Retainer
17 826-1374 Screw, #10 X ½-inch Hex Washer Head (Pkg. of 25)
18 826-1359 Screw, 4-40 X ¾-inch Slotted Round Head (Pkg. of 25)
19 826-1361 Screw, 8-32 X 1-inch Slotted Truss Head (Pkg. of 25)
20 826-1371 Screw, #8 X ½-inch Drill Point Hex Head (Pkg. of 25)
21 809-0503 Screw, 8-32 X ½-inch Hex Head
22 809-0186 Washer, #8 Lock
23 WIR-0166SP Wire Bundle, 200-250VAC Basket Lift w/Relay

24 910-4776 Cover, Modular Basket Lift Rear S/S (Use 900-4776 for Mild Steel)

25 809-0127 Screw, ¼-20 X ½-inch Slotted Round Head
26 823-2704 Arm, Left Basket Lift
27 823-2705 Arm, Right Basket Lift
28 810-0179 Button, Plug
29 806-9110SP Roller Assembly, Basket Lift
30 910-8112 Bracket, Basket Lift Roller
31 810-0194 Roller, Basket Lift
32 810-0374 Spacer, Basket Lift Roller
33 809-0508 Bolt, ¼-20 X 1¼ -Inch
34 809-0190 Washer, ¼-inch Flat
35 809-0047 Nut, ¼-20 Cap

* 807-3700 Wiring Harness, Pro Series Electric Basket Lift (Plugs into Item 6)

* Not illustrated. Use standard part.

2-3

2.3 Cabinetry

2.3.1 Back Panels, Control Panel Frames, Doors, Sides, Tilt Housings, and Top Caps

1

2

3

13

12

14

4

18

1716

9

7

5

6

15

11

10

8

2-4

ITEM

STANDARD

PART #

EURO-LOOK

PART #

COMPONENT

1 Back Panel, Upper (Panel for five station fryer shown)

210-2299 200-6630 Two Station Fryer
210-2380 200-6785 Three Station Fryer
210-3490 200-6786 Four Station Fryer
210-3670 200-6787 Five Station Fryer

2 Back Panel, Center (Panel for five station fryer shown)

210-2298 200-2298 Two Station Fryer
210-2379 200-2379 Three Station Fryer
210-3489 200-3489 Four Station Fryer
210-3669 200-3669 Five Station Fryer

3 Back Panel, Lower (Panel for five station fryer shown)

210-4430 200-4426 Two Station Fryer
210-4431 200-4427 Three Station Fryer
210-4432 200-4428 Four Station Fryer
210-4433 200-4429 Five Station Fryer

4 Frame, Control Panel (Frame for five station fryer shown)

806-7172SP 106-4378 Two Station Fryer (use 106-5221SP for fryers mfd. After 6.22.05)
806-7173SP 106-4391 Three Station Fryer (use 106-5018SP for fryers mfd. After 6.22.05)
806-7174SP 106-4392 Four Station Fryer (use 106-5019 for fryers mfd. After 6.22.05)
106-2171SP 106-4393 Five Station Fryer (use 106-5020 for fryers mfd. After 6.22.05)

5 210-4435 Side, Standard Cabinet Left or Right
6 810-2346 810-1105 Magnet, Door
7 211-4616 201-8481 Side, Filter Ready Cabinet Left
8 212-4616 202-8481 Side, Filter Ready Cabinet Right
9 910-0889 Cover, 5-inch X 5-inch Access

10 910-0890 Cover, 5-inch X 7-inch Access
11 809-0359 Screw, #8 X ¼-inch Hex Washer Head
12 Tilt Housing (Housing for five station fryer shown)

824-1061 824-1303 Two Station
824-1062 824-1335 Three Station
824-1063 824-1336 Four Station

824-1065 824-1337 Five Station
13 826-1351 809-0015 Nut Retainer, ¼-20 (Pkg. of 10 – receives basket hanger thumbscrew)
14 Top Cap (Top cap for five station fryer shown)

106-3033SP 106-4414 Two Station (use 106-5196 for fryers mfd. After 6.22.05)

106-3035SP 106-4437 Three Station (use 106-5197 for fryers mfd. After 6.22.05)

106-3036SP 106-4439 Four Station (use 106-5198 for fryers mfd. After 6.22.05)

824-0890 106-4441 Five Station (use 106-5199 for fryers mfd. After 6.22.05)
15 806-6545SP 106-4397 Door, Left or Right (Left shown – move handle to opposite side for Right)
16 809-0266 Screw, #10 X ½-inch Phillips Truss Head
17 810-1422 210-6816 Handle, Wireform Door
18 106-0554 Pin Assembly, Door

* 810-0275 Spring, Door Pin

* Not illustrated. Use standard part.

2-5

2.3.2 Cabinet Bases, Braces, and Associated Parts

See Page 2-4 for cabinet sides.

2

See Page 2-32 for rear bridge

support/oil return manifold.

1

20

2414

4

282218

8 25

21 23

7

16

2410

9 24

2412

2410

11 24

2415

See Page 2-28 for filt er rails

and associated hardware.

27 28 33

27 28 32

5

17

3

26

30

31

29

19

6

The 5-Stat ion cabinet illustra ted is typical of all
Pro Series Electric cabinets. All components
used in Pro Series cabinets are identified, but not
all components are used in every configuration.

2-6

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 106-1265SP Upright Assembly, Left

2 106-1266SP Upright Assembly, Right

3 200-1651 Support, Cross Cabinet

4 200-1659 Divider, Cabinet

5 200-2293 Brace, Single Station Lower

6 200-3774 Brace, Double Station Lower

7 Brace, Front Horizontal

200-2331 Two-Station Fryer
200-2296 Three-Station Fryer
200-2733 Four-Station Fryer
200-3590 Five-Station Fryer

8 Brace, Rear Horizontal

200-2284 Two-Station Fryer
200-2295 Three-Station Fryer
200-2725 Four-Station Fryer
200-3592 Five-Station Fryer

9 200-4422 Support, Contactor Box Right Station 3 or Station 5

10 201-4425 Support, Contactor Box Left Station 4 or Station 5
11 202-4425 Support, Contactor Box Right Station 3
12 200-4423 Support, Contactor Box Stations 3 and 4
13 200-4447 Support, Contactor Box Front to Rear
14 201-5369 Support, Contactor Box Station 2
15 202-5369 Support, Contactor Box Station 1
16 200-4424 Post, Door
17 810-2346 Magnet, Door
18 200-4786 Support, Oil Return Manifold
19 210-5595 Hinge, Door
20 210-1490 Bracket, Rear Support
21 900-1224 Bracket, Frypot
22 809-0131 Bolt, ¼-20 X ¾-inch Hex Head (also used w/Item 27 to mount filter rails)
23 826-1371 Screw, #8 X ½-inch Drill Point Hex Head (Pkg. of 25)
24 826-1330 Screw, 10-32 X ⅜-inch Slotted (Pkg. of 25, used to attach contactor box)
25 809-0256 Nut, 10-32 Keps Hex
26 809-0412 Screw, #10 X ½-inch Hex Washer Head (primary cabinet screw)
27 809-0417 Nut, ¼-20 Hex Flange
28 809-0429 Bolt, ¼-20 X 2-inch Hex Head
29 200-5417 Brace, Rear Channel Corner
30 Channel, Base Rear

200-5463 Two-Station Fryer
200-5538 Three-Station Fryer
200-5537 Four-Station Fryer

200-5536 Five-Station Fryer
31 824-1131 Channel, Base Side
32 810-0326 Caster with Brake
33 810-1494 Caster without Brake

* 810-1234 Leg, Stainless Steel 8.5-inch Adjustable (mounts with Items 27 and 28)
* 823-4386 Leg, Navy Shipboard (mounts with Items 27 and 28)

* Not Illustrated. Use standard part.

2-7

2.4 Drain System Components

2.4.1 Drain Tube Sections and Associated Parts

See Page 2-12 for Drain Valves

5

6

7

8

12

14

16

1

2

11

3

4

21

2022

13

15

6

7

10

23

5

1

2

3

4

9

17

18

19

2-8

STANDARD

ITEM

PART # **

COMPONENT

1 813-0284 Nipple, ¾ X 1-inch NPT
2 816-0092 Grommet, 1-inch Drain
3 826-1345 Washer, 1-inch Drain (Pkg. of 25)
4 809-0347 Nut, 1-inch NPT Retainer
5 809-0893 Nut, 8-32 High Crown Acorn
6 826-1348 Cover, Drain Cleanout (Pkg. of 5)
7 816-0021 Gasket, Drain Cleanout
8 Drain Tube, Left End Short

823-3380 Full-Vat
823-3379 Dual-Vat

9 Drain Tube, Right End Short

823-1551 Full-Vat
823-1549 Dual-Vat

10 Drain Outlet

823-3229 With Vacuum Breaker Vent

823-2336 Without Vacuum Breaker Vent

11 810-2492 Fitting, Quick-Connect Straight (receives Teflon vent tube)
12 Drain Tube, Left End Short Vented

823-2637 Full-Vat

823-2636 Dual-Vat

13 Drain Tube, Right End Long

823-1508 Full-Vat

823-1543 Dual-Vat

14 823-3675 Drain Tube, Spreader Cabinet Short
15 Drain Tube, Open End Short

823-0718 Full-Vat

823-0725 Dual-Vat

16 823-0731 Drain Tube, Spreader Cabinet Long
17 Drain Tube, Open End Long

823-0717 Full-Vat

823-0724 Dual-Vat

18 823-3674 Drain Outlet, Filter Magic Left
19 823-3673 Drain Outlet, Filter Magic Right
20 810-0396 Clamp
21 809-0401 Screw, 10-32 X ¾-inch Hex Head
22 809-0256 Nut, 10-32 Keps Hex
23 816-0032 Gasket

* 826-0877 Kit, Square Drain Clamp (2 each of Items 20-22 and 1 of Item 23)
* 811-1071 Tube, Teflon Vent

* Not illustrated.

** See page 2-11 for an Euro-Look parts list.

2-9

2.4.2 Euro-Look Drain Tube Section and Associated Parts

1

See Page 2-14 for Drain Valves

7

6

8

6

7

1

2

2

5

3

3

4

4

2-10

EURO-LOOK

ITEM

PART# **

COMPONENT

1 Drain Tube, Left/Right End Short

823-4625 Full-Vat
823-4624 Dual-Vat

2 Drain Tube, Left/Right Open Short

823-4643 Full-Vat
823-4642 Dual-Vat

3 Drain Tube, Right End Long

823-4639 Full-Vat
823-4638 Dual-Vat

4 Drain Tube, Left/Right Open Long

823-4641 Full-Vat

823-4640 Dual-Vat
5 823-4892 Drain Outlet
6 816-0625 Sleeve
7 809-0969 Clamp
8 810-2492 Fitting, Quick-Connect Straight (receives Teflon vent tube)
* KIT6033 Kit, Round Drain Clamp (2 or Item 7 and 1 of Item 6)
* 811-1071 Tube, Teflon Vent

* Not illustrated.
** See page 2-9 for a standard parts list.

2-11

2.4.3 Drain Valves and Associated Parts (Units with Built-In Filtration)

Dual-Vat Drain Valve

Assembly 106-2893SP

4

1

2

3

5

6

7

8

9

Compression Washers
(furnished with Item 12)

10

Flat Washer
(furnished with Item 12)

11

12

Compression Washers

(furnished with Item 17)

Plastic Washer

(furnished with Item 17)

15

13

14

5

6

7

8

Full-Vat Drain Valve

Assembly 806-7434SP

16

17

2-12

ITEM

STANDARD

COMPONENT

PART # **

1 809-0539 Nut, ⅜-16 2-Way Hex Lock

2 900-2934 Retainer, Dual-Vat Drain Valve Nut

3 823-4133 Handle, Dual-Vat Drain Valve

4 810-0677 Grip, Drain Handle

5 809-0237 Nut, 4-40 Keps Hex

6 901-2348 Cover, Dual Vat Drain Safety Switch

7 807-2103 Microswitch, CE Straight Lever

8 816-0220 Insulation, Drain Safety Switch

9 810-1165 Washer, Teflon Drain Valve
10 809-0196 Washer, ⅜-inch Flat
11 106-2671SP Bracket Assembly, Dual-Vat Drain Safety Switch
12 810-1338 Valve, 1-inch Dual-Vat Drain
13 809-0540 Nut, ½-13 2-Way Hex Lock
14 900-2609 Handle, Full-Vat Drain Valve
15 814-0047 Sleeve, Red Handle
16 806-8137SP Bracket Assembly, Full-Vat Drain Safety Switch
17 810-1020 Valve, 1.25-inch Full-Vat Drain

* WIR0572 Wire Bundle, Drain Safety Switch

* Not illustrated.

** See page 2-15 for a Euro-Look parts list.

2-13

2.4.4 Euro-Look Drain Valves and Associated Parts (Units with Built-In Filtration)

4

1

2

3

Dual-Vat Drain Valve

Assembly 106-3761

Compression Washers

10

18

9

Flat Washer

Plastic Washer

20

15

5

6

7

8

11

12

13

19

14

Compression Washers

6

Full-Vat Drain Valve
Assembly 106-3760

5

8

16

17

7

9

18

20

2-14

ITEM

EURO-LOOK

COMPONENT

PART # **

1 809-0539 Nut, ⅜-16 2-Way Hex Lock

2 900-2934 Retainer, Dual-Vat Drain Valve Nut

3 823-4133 Handle, Dual-Vat Drain Valve

4 810-0677 Grip, Drain Handle

5 809-0237 Nut, 4-40 Keps Hex

6 901-2348 Cover, Dual Vat Drain Safety Switch

7 807-2103 Microswitch, CE Straight Lever

8 816-0220 Insulation, Drain Safety Switch

9 810-1165 Washer, Teflon Drain Valve
10 809-0196 Washer, ⅜-inch Flat
11 106-2671 Bracket Assembly, Dual-Vat Drain Safety Switch
12 810-1114 Valve, 1-inch Dual-Vat Drain
13 809-0540 Nut, ½-13 2-Way Hex Lock
14 900-2609 Handle, Full-Vat Drain Valve
15 814-0047 Sleeve, Red Handle
16 806-8137 Bracket Assembly, Full-Vat Drain Safety Switch
17 810-1018 Valve, 1.25-inch Full-Vat Drain
18 200-6496 Support, 3” Drain
19 900-2936 Retainer, Full-Vat Drain Valve Nut
20 816-0135 Round Drain O-Ring

* WIR0572 Wire Bundle, Drain Safety Switch

* Not illustrated.
** See page 2-13 for a standard parts list.

2.4.5 Drain Valves and Associated Parts (Units without Built-In Filtration)

1

ITEM

4

STANDARD

PART #

5

EURO-LOOK

PART # COMPONENT

2

1 810-1569 Valve, 1.25-inch Non-Filter Full-Vat Drain

2 806-7915SP Valve, 1-inch Non-Filter Dual-Vat Left Drain

3 806-7916SP Valve, 1-inch Non-Filter Dual-Vat Right Drain

4 812-1226 Drain Extension, 1.25-inch

5 812-1227 Drain Extension, 1-inch

Use standard part.

3

2-15

2.5 Electronics and Wiring Components

2.5.1 Component Boxes

1710

2014

7

4 16 19

6

205 2220

201214 20

11 20

4 16 1920 229 11 202054 16 1920 229 10 20205

202

7

6

202202

120V, 440V Navy, and 480V Bo xes 208-240V NON-CE Boxes

1

98 17 18 21

26

20

1

24

25

23203

7

9 13 20

208-240V CE Boxes

10 20

1

6

98 17 18 21 98 17 18 21

NOTE 1: The transformer on the left side of the

component box is present only in units with built-in

filtration and then only in the left component box.

NOTE 2: See Page 2-23 for Component Box 15-Pin

Wiring Harnesses.

2-16

ITEM

STANDARD

PART #

EURO-LOOK

PART #

COMPONENT

1 106-1531SP Box Assembly, Component
2 200-3300 Bracket, Component Box Strain Relief
3 200-3746 Bracket, Navy Circuit Breaker (US Navy units only)
4 806-9495SP Terminal Block and Wire Assembly
5 807-0012 Relay, 18 Amp ⅓ HP 24V Coil
6 807-0037 Terminal, ¼-inch Push-on
7 807-0121 Bushing, Heyco Plastic AB-625-500
8 807-1321 Holder, AGC Panel-Mount ¼-inch Fuse

9 807-1597 Fuse, 3 Amp Slow-Blow
10 807-2180 Transformer, 208-240V 50VA
11 807-2181 Transformer, 100-120V/24V 60VA
12 807-0680 Transformer, 208-240V/24V 20VA
13 807-2191 Transformer, 208-240V/12V 30VA
14 807-0855 Transformer, 100-120V/12V 20VA
15 807-0979 Transformer, 208-240V/12V 43VA
16 826-1366 Nut, 4-40 Keps Hex (Pkg. of 25)
17 809-0250 Nut, 6-32 Keps Hex
18 809-0349 Spacer, 4mm X 6mm Aluminum
19 826-1359 Screw, 4-40 X ¾-inch Slotted Round Head (Pkg. of 25)
20 809-0359 Screw, #8 X ¼-inch Hex Washer Head
21 Interface Board

806-6336SP Standard (Non-Triac), Full- or Dual-Vat
806-6347SP Triac, Full- or Dual-Vat
106-3721 Fast Computer, Full- or Dual-Vat

* 807-3932 Relay, Heat and Latch 12 VDC SPDT 12A
22 806-7179SP Sound Device
23 807-0069 Circuit Breaker, 10 Amp
24 200-3844 Guard, Finger
25 810-2445 Plug Button
26 200-3243 Brace, Component Box

* Not illustrated. Use standard part.

2-17

2.5.2 Contactor Boxes

12 35

312713

4 35

3 35

8 29 32

17 18 36

STANDARD 14/17 kW

CONFIGURATIONS

349

291110

5 7 27 31

1

2

36

OR

6 35

WYE configurations

also have Item 21,

mounted with Items 30

and 33, here.

TRIAC

32298

361817

354

353

19 28

OR

20 28

CONFIGURATIONS

1

2

5

3631277

OR

4 35

12 35

312714

3 35

8 29 32

356

17 18 36

22 kW

CONFIGURATIONS

349

291110

5 7 27 31

1

2

36

OR

6 35

NAVY

CONFIGURATIONS

361815

OR

1

361816

2

NOTE: See Pages 2-23 through 2-25 for Contactor Box W i ri ng Harness e s

12 35

32298

361817

356

23 18 36

22 25 26

24 25 26

2-18

NOTES: Left and right contactor box assemblies are mirror images of one another. With the exception of the

box itself, all components of a left-hand assembly are the same as those in the corresponding right-hand
assembly and vice versa. The configurations illustrated show all possible components, but a particular
configuration may not have all the components shown.

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 106-1536SP Box Assembly, Left Contactor
2 106-1537SP Box Assembly, Right Contactor
3 200-3111 Cover, Cord Cutout
4 900-2752 Plate, Cordset Adapter
5 200-2334 Door, Contactor Box Hinged
6 200-4712 Door, Contactor Box w/o Hinge
7 810-0519 Hinge, Contactor Box Door
8 807-0070 Terminal, Ground Lug

9 200-2336 Bracket, Contactor Box Fuse Block
10 807-0501 Fuse Block, 3-Pole
11 807-2240 Fuse, 60 Amp 300VAC
12 200-2337 Bracket, Mercury Contactor
13 807-1071 Contactor, 24V 30 Amp Mercury
14 807-0884 Contactor, 24V 35-50 Amp Mercury

15 807-2284 Contactor, 24V 50 Amp Mechanical (only in 14 & 17kW Navy units)
16 807-2283 Contactor, 24V 63 Amp Mechanical (only in 22kW Navy units)

17 810-1202 Contactor, 24V 40 Amp 3-Pole
18 809-0448 Clip, Tinnerman

19** 806-8674 Heatsink Assembly, DV Solid State Relay (See components below)
20** 806-8673 Heatsink Assembly, FV Solid State Relay (See components below)

21 806-9124 Filter Assembly, Triac (used in Wye-configured Triac units only)

22 807-0012 Relay, 18 Amp  HP 24V Coil
23 807-0064 Transformer, 480V/120V 150VA
24 807-1683 Relay, 12VDC
25 826-1358 Nut, 6-32 Keps Hex (Pkg. of 25)
26 826-1365 Screw, 6-32 X ⅜-inch Slot Head (Pkg. of 25)
27 809-0104 Screw, 8-32 X ½-inch Slot Head
28 826-1330 Screw. 10-32 X ⅜-inch Slot Head (Pkg. of 25)
29 809-0123 Screw, #10 X ¾-inch Slot Head
30 826-1366 Nut, 4-40 Keps Hex (Pkg. of 25)
31 809-0247 Nut, 8-32 Keps Hex
32 826-1376 Nut, 10-32 Keps Hex (Pkg. of 10)
33 826-1359 Screw, 4-40 X ¾-inch Slot Head (Pkg. of 25)
34 809-0359 Screw, #8 X ¼-inch Hex Washer Slot Head
35 809-0360 Screw, #8 X ⅜-inch Hex Washer Slot Head
36 826-1374 Screw, #10 X ½-inch Hex Head (Pkg. of 25)

* 200-5627 Lid, Left or Right Contactor Box

* Components of Items 19 and 20
** 826-1562 Relay, Solid State 50 Amp 280V

* 807-2749 Heatsink, Solid State

* 807-0037 Terminal, ¼-inch Push-on

* 809-0096 Screw, 6-32 X ⅝-inch Slot Head

** Not illustrated.

Use standard part.

** Dual-vat Assembly has six relays (826-1562); full-vat Assembly has three relays.

2-19

2.5.3 Heating Element Assemblies and Associated Parts

FULL-VAT ELEMENT ASSEMBLY DUAL-VAT ELEMENT ASSEMBLY

3

4

9

7

6

8

10

22

5

11

20

21

1

1

1

1

2

1312

15

1413

16

17

18

19

24

23

NOTES:

The dual-vat assembly is the same as the full-vat assem bly except for having two of Items 2, 12, 18 and 19, two of Item
20 in place of Item 16, two of Item 21 in place of Item 17, and two of Item 10 instead of one Item 10 and one Item 11.
The only difference between element assemblies for different vol t age and kW ratings i s the element itself (I t em 1)

Items 23 and 24 are shown as associat ed parts. They are not part of either element assembly.

2-20

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 Element

826-2151 200V 17.0 kW (also used for 220V 8.5 kW)
826-2156 200V 18.5 kW
826-2167 200V 11.0 kW
826-2149 208V 17.0 kW
826-2150 208V 18.5 kW
826-2172 208V 11.0 kW
826-2155 220V 17.0 kW (also used for 240V 8.5 kW)
826-2151 220V 18.5 kW (also used for 200V 7.0 kW)
826-2164 220V 11.0 kW
826-2152 230V 17.0 kW
826-2153 230V 18.5 kW
826-2165 230V 11.0 kW
826-2154 240V 17.0 kW
826-2155 240V 18.5 kW (also used for 220V 7.0 kW)
826-2166 240V 11.0 kW
826-2157 380V 17.0 kW
826-2158 380V 18.5 kW
826-2168 380V 11.0 kW
826-2159 440V 17.0 kW
826-2160 440V 18.5 kW
826-2169 440V 11.0 kW
826-2161 480V 17.0 kW
826-2162 480V 18.5 kW

826-2170 480V 11.0 kW
2 826-1526 Probe, Temperature
3 106-0004SP Tilt Plate Assembly
4 106-0572SP Bracket, Left Spring Slot
5 106-0573SP Bracket, Right Spring Slot
6 910-9641 Tilt Plate
7 810-0035 Hinge
8 826-1330 Screw, 10-32 X ⅜-inch Slotted Truss Head (Pkg. of 25)
9 826-1376 Nut, 10-32 Keps Hex (Pkg. of 10)

10 826-1339 Bushing, .375-inch Split (Pkg. of 10)
11 816-0480 Plug, .375-inch Dome
12 910-5022 Bracket, Temperature Probe
13 809-0518 Screw, 8-32 X ⅜-inch Slotted Hex Head
14 910-2042 Clamp, Element (Short)
15 910-5213 Clamp, Element (Long)
16 910-3681 Support, Full-Vat Element Rear
17 823-2377 Support, Full-Vat Element Front
18 810-1233 Handle, Element Lift
19 810-1212 Pin, .125 X .5-inch Split
20 910-5214 Support, Dual-Vat Element Rear
21 823-2378 Support, Dual-Vat Element Front
22 809-0567 Tie-Wrap, Metal
23 200-2060 Bracket, Lower Spring Slot
24 810-0297 Spring, Element

* 826-1061

* 826-2228

Tilt Switch, Mercury Non-CE (Full-Vat requires one switch and
Dual-Vat requires two.)
Magnetic Tilt Switch CE (Full-Vat requires one switch and Dual­Vat requires two.)

* Not illustrated. Use standard part.

2-21

2.5.4 Controllers

1 2 3

NOTE: See Page 2-27 for Interface Board to Controller Wiring Harness

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 Computer Magic III

106-1193 106-4335 Full-Vat (CE)

106-1194 106-4336 Dual-Vat (CE)
806-7158SP 106-4373 Full-Vat (Non-CE)
806-7159SP 106-4374 Dual-Vat (Non-CE)
806-7162SP 106-4337 Full-Vat (Triac/Solid State)
806-7163SP 106-4338 Dual-Vat (Triac/Solid State)

2 Digital Controller

106-1507 106-4343 Full-Vat (CE)

106-1508 106-4344 Dual-Vat (CE)

106-1503 106-4339 Full-Vat (Non-CE)

106-1504 106-4340 Dual-Vat (Non-CE)

3 Basket Lift Timer

106-2090SP 106-4365 Full-Vat (CE)
106-2091SP 106-4366 Dual-Vat (CE)
106-2088SP 106-4363 Full-Vat (Non-CE)
106-2089SP 106-4364 Dual-Vat (Non-CE)

4 Solid-State (Analog) Controller

806-7422 106-4333 Full-Vat

806-7423 106-4334 Dual-Vat

4

SOLID STATE

2-22

2.5.5 Wiring

2.5.5.1 Contactor Box Wiring Assemblies – 12-Pin Dual-Vat C-1

1
2
3
4
5

1

2

6
7
8

9
10
11
12

1
2
3
4
5
6
7
8

9
10
11
12

BLACK
GREEN/YELLOW
WHITE
BROWN
ORANGE
BLACK

ORANGE

WHITE

BLACK

BLACK

BLACK
GREEN/YELLOW
WHITE
BROWN
ORANGE
BLACK

ORANGE

WHITE

BLACK

YELLOW

BLACK

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 106-2428SP Standard
2 106-2343SP Triac

Use standard part.

2-23

2.5.5.2 Contactor Box Wiring Assemblies – 12-Pin Full-Vat C-1

1
2
3
4
5

1

2

3

6
7
8

9
10
11
12

1

2

3

4

5

6

7

8

9
10
11
12

1

2

3

4

5

6

7

8

9
10
11
12

BLACK
GREEN/YELLOW
WHITE
BROWN

WHITE

BLACK

ORANGE
BLACK

BLACK
GREEN/YELLOW
WHITE
BROWN

WHITE

BLACK

ORANGE
BLACK

YELLOW

BLACK
GREEN/YELLOW
WHITE
BROWN

WHITE

BLACK

RED
ORANGE
BLACK

YELLOW

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 Standard

106-2474SP Other than 480V

106-2522SP 480V
2 106-2475SP Triac
3 106-2477SP Navy

Use standard part.

2-24

2.5.5.3 Contactor Box Wiring Assemblies – 6-Pin (Left Element)

BLUE
BLUE
BLUE
BLACK
BLACK
BLACK

BLUE
BLUE
BLUE
BLACK
BLACK
BLACK

PART # COMPONENT

ITEM

1

2

STANDARD

PART #

1
2
3
4
5
6

1
2
3
4
5
6

EURO-LOOK

1 106-2426SP 14/17 kW
2 106-2473SP 22 kW and Navy

2.5.5.4 Contactor Box Wiring Assemblies – 9-Pin (Right Element)

Use standard part.

BLUE
BLUE
BLUE
BLACK
BLACK
BLACK

BLUE
BLUE
BLUE
BLACK
BLACK
BLACK

PART # COMPONENT

ITEM

1

2

STANDARD

PART #

1
2
3
4
5
6
7
8
9

1
2
3
4
5
6

7
8
9

EURO-LOOK

1 106-2425SP 14/17 kW
2 106-2472SP 22 kW and Navy

Use standard part.

2-25

2.5.5.5 Main and Multi-Fryer Wiring Harnesses

15-Pin Male Connector

807-0804 (Rear of Fryer)

C6

1

12-Pin Male Connector

807-0160 (Contactor Box)

C1

J6

12-Pin Male Connector

807-0160 (Interface Board)

J1
J4
J5
J2

4-Pin Female Connector

807-3232 (Drain Safety Switches)

15-Pin Male Connector

807-0804 (Component Box)

6-Pin Male Connector

807-0157 (Basket Lift Harness)

12-Pin Male Connector

807-0160 (Interface Board)

FRYER #3

Item 3: 807-3716

Male Disconnect Pin
807-1049

Female Disconnect Pin
807-0701

Item 4: 807-3717

2

FRYER #4

Item 5: 807-3718

Female Disconnect Pin
807-0701

Male Disconnect Pins

807-1049

12-Pin Male Connector

807-0160

FRYER #5

12-Pin Connector

Wiring for 807-3716

12-Pin Connector

Wiring for 807-3717

2-26

12-Pin Connector

Wiring for 807-3718

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 807-3769 Main
2 807-3715 Two-Fryer Battery
3 807-3716 Three-Fryer Battery
4 807-3717 Four-Fryer Battery
5 807-3718 Five-Fryer Battery

NOTE: Harnesses for 3-, 4-, and 5-Fryer batteries are similar to 807-3715 but

have extra sets of leads as appropriate for the number of fryers in the battery. The
connections to Fryer #1 J2 and J4 are the same for all.

2.5.5.6 Component Box Wiring Harnesses – 15-Pin

Use standard part.

ITEM

STANDARD

PART #

1

EURO-LOOK

PART # COMPONENT

2 3

4

1 106-2506SP 208-480V (With Filter)
2 106-2507SP 208-480V (Without Filter)
3 106-2508SP 120V (With Filter)
4 106-2509SP 120V (Without Filter)

2.5.5.7 Interface Board to Controller Wiring Harness – 15-Pin

Use standard part.

806-2071SP

2-27

2.6 Filtration System Components

NOTE: Some early production

1

units were configured this way.

37

38

24

29

2

3

4

19

17

25

16

30

28

12119

14

8

20

121110

18

36

35

34

25

18

22

24

23

21

8

27

26

32

33

31

7

6

15

5

13

2-28

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

* 826-1979 Filter Pan Roller Kit (four each of Items 7 and 8)
* 826-1980 Service Filter Pan (Item 5 minus Item 2)
* 826-1981 Service Filter Pan Assembly (Service Filter Pan above plus Items 3 and 4)
* 826-1392 816-0012 O-Ring (Pkg. of 5; used with Item 5)
* 813-0568 Plug, ⅛-inch Socket Head Pipe (component of Item 5; two required)
* 811-1071 Tubing, ¼-inch OD Teflon Vent (sold by the foot)
* 106-2851SP Heater Strip Assembly, 100-120V
* 106-2852SP Heater Strip Assembly, 208-250V

1 823-4637 823-4787 Lid (for units built before Feb 2004, use 823-4391)

2 810-2874 Crumb Tray (component of Item 5)

3 810-2091 Hold-Down Ring (two are needed for pad hold-down option)

4 200-2124 SanaGrid Filter Screen
5 106-2617SP Pan, One-Piece Filter (includes Item 2)
6 810-2012 Rail Set, Filter Pan Roller (includes one left and one right)
7 810-2198 Roller, Filter Pan and Rail
8 826-1372 Nut, ¼-20 Hex (Pkg. of 10)

9 823-4589 823-4675 Bracket, Lid Support (for units built before Feb 04, use 823-3875)

10 Guide, Filter Pan Lid

200-3556 Left

200-6709 Right
11 809-0104 809-0503 Screw, 8-32 X ½-inch Slotted Truss Head
12 809-0247 Nut, 8-32 Hex Keps
13 823-3879 Suction Tube
14 200-4408 Rail, Left Filter
15 200-4409 Rail, Right Filter
16 Motor and Gasket Kit

826-1785 807-3858 100V 50/60 Hz

826-1712 807-3859 115V 50/60 Hz

826-1756 807-3860 208V 50/60 Hz

826-1757 807-3861 220-240V 50/60 Hz

826-1755 807-3862 250V 50/60 Hz
17 826-1264 Pump and Gasket Kit

810-2716 Pump, Viking 4GPM 2-piece

816-0093 Gasket, Pump/Motor
18 807-2484 Valve, ¼-inch Solenoid
19 813-0165 Elbow, ½-inch 90° Street
20 813-0342 Elbow, ½-inch 45° Street
21 813-0530 Tee, ½-inch X ¼-inch X ½-inch Reducing
22 813-0022 Nipple, ½-inch Close
23 813-0838 Nipple, ¼-inch Close
24 813-0304 Bushing, ½-inch to ¼-inch Flush
25 810-1668 Adapter, ⅝-inch to ½-inch NPT Male
26 810-1669 Adapter, ⅝-inch to ½-inch NPT Female
27 810-1680 Flexline, 6.5-inch Oil Return
28 810-1369 Flexline, 17.5-inch Oil Return

* Not illustrated.

Use standard part.

Continued on next page…

2-29

29 810-1055 Flexline, 11.5-inch Oil Return
30 807-3828 Cable, FootPrint Pro Pump Motor
31 826-1375 809-0401 Screw, 10-32 X ¾-inch Hex Trim Head (Pkg. of 5)
32 200-7112 Bridge, Filter Motor
33 210-3149 Support, Contactor Box
34 813-0003 Tee, ½-Inch
35 813-0298 Nipple, ½-inch 2.0-inch
36 813-0537 Nipple, ¼-inch 2.0-inch
37 810-2493 Fitting, ¼-inch X 90° Quick-Connect
38 810-1160 Flexline, 3.0-inch Oil Return

* 810-1043 Flexline, 9.5-inch Oil Return
* 810-1057 Flexline, 13.0-inch Oil Return

* Not illustrated. Use standard part.

2-30

2.7 Frypot Assemblies and Associated Parts

3

5

4

2

7

3

4

4

1

4

4

5

6

8

2-31

ITEM PART# COMPONENT

1 823-4776SP Frypot, Full-vat
2 823-4779 Frypot, Dual-vat
* 823-4747SP Frypot, Full-vat, Filter Magic
* 823-4777 Frypot, Dual-vat, Filter Magic
* 823-2452SP Frypot, Full-vat, EPRI/Triac (with insulation, 806-8167SP)
* 823-2461 Frypot, Dual-vat, EPRI/Triac (with insulation, 106-4582SP)
* 823-5001 Frypot, Full-vat, EPRI/Triac with Filter Magic (with insulation, 106-4575SP)
* 823-5002 Frypot, Dual-vat, EPRI/Triac with Filter Magic (with insulation, 106-4576SP)
3 Thermostat Assembly, High-Limit

806-7543 Non-CE Full Vat 425°F (218°C) (Color-Coded Black)
806-8035 Non-CE Dual Vat 435°F (224°C) (Color-Coded Red)
806-8132 CE 415°F (213°C) used in 14 & 17kW fryers (Color-Coded Yellow)
806-8536 CE 405°F (207°C) used in 22 kW fryers (Color-Coded White)

4 812-0211 Insulation, Kaowool 17-inch X 10-inch X ½-inch (4 required per pot)

5 900-4100 Retainer, Side Insulation
6 900-4101 Retainer, Front Insulation
7 900-1345 Retainer, Rear Insulation
8 826-1376 Nut, 10-32 Keps Hex (Pkg. of 10)

* Not illustrated.

2-32

2.8 Oil Return System Components

26

25

24

21

20

23

22

10

8

14

16

12

4

3

15

9

13

11

19

18

17

5

4

3

6

5

7

2

1

2-33

ITEM

STANDARD

PART #

EURO-LOOK

PART # COMPONENT

1 806-4505SP Power Shower Assembly, Full-Vat
2 806-4527SP Power Shower Assembly, Dual-Vat
3 826-0992 Seal, Power Shower (Pkg. of 3)
4 809-0415 Screw, Power Shower Cleanout
5 814-0001 Grip, Power Shower Handle
6 823-1486 Power Shower, Full-Vat
7 823-1510 Power Shower, Dual-Vat
8 807-2103 Microswitch, Oil Return

9 810-2330 Handle, Oil Return Valve
10 809-0601 Clip, Clevis
11 810-0677 Grip, Oil Return Valve Handle
12 200-5401 Bracket, Handle Retainer
13 200-2520SP Bracket, Oil Return Microswitch
14 816-0220 Insulation, Oil Return Microswitch
15 826-1359 Screw, 4-40 X ¾-inch Slotted Pan Head (Pkg. of 25)
16 826-1366 Nut, 4-40 Keps Hex (Pkg. of 25)
17 813-0165 Elbow, ½-inch X 90° Street
18 810-0278 Valve, ½-inch Ball
19 810-1668 Adapter, ⅝-inch to ½-inch NPT Male
20 810-1680 Flexline, 6.5-inch
21 810-1669 Adapter, ⅝-inch to ½-inch NPT Female
22 813-0469 Cap, ½-inch NPT Pipe

23 810-2255 Manifold, Two-Station Fryer (use 810-2543 for non-filter units)
24 810-2256 Manifold, Three-Station Fryer (use 810-2544 for non-filter units)
25 810-2257 Manifold, Four-Station Fryer (use 810-2545 for non-filter units)
26 810-2312 Manifold, Five-Station Fryer (use 810-2546 for non-filter units)

* Not illustrated. Use standard part.

2-34

Frymaster, L.L.C., 8700 Line Avenue, PO Box 51000, Shreveport, Louisiana 71135-1000

Shipping Address: 8700 Line Avenue, Shreveport, Louisiana 71106

TEL [phone] FAX (Parts) 1-318-219-7140 (Tech Support) 1-318-219-7135

PRINTED IN THE UNITED STATES

SERVICE HOTLINE

1-800-551-8633

819-5990

MAR 2008