Frigidaire FCRS201RFB4, FCRS201RFB3, FCRS201LFB4, FCRS201LFB3, FCRS201LFB2 Owner’s Manual

...

FRIGIDAIRE

COMMERCIAL

COMMERCIAL FREEZER/REFRIGERATOR

GLASS DOOR REFRIGERATOR

TABLE OF CONTENTS

Product Registration ................................................ 2

Important Safety Instructions .................................... 2

Electrical Information ............................................... 3

Caster Installation and Setup (Glass Door) ................... 3-4

Caster Installation and Setup (Non-Glass Door) .......... 5-6

Appliance Start-up .................................................... 6

Features ................................................................. 6-7

Routine Maintenance ............................................... 7

Energy Conservation Measures ................................. 7

Troubleshooting Guide ............................................. 8-9

Wiring Diagram ....................................................... 10

Warranty ............................................................... 11

READ AND SAVE THESE INSTRUCTIONS 297121600(June2006)

Product Registration

Important Safety Instructions

Read all instructions before using this appliance

For Your SafetyL,_wm_dl_

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this unit or any other appliance. Read

product labels for flammability and other warnings.

These instructions include information which is intended to assure the operator of correct installation, operation and service.

Before attempting installation, adjustment or maintenance, be certain of the following:

• That you have read and fully understand the instructions.

• That you have all the tools required and are trained to use them.

• That you have met all installation and usage restrictions and are familiar with the functions and operations of the unit.

• That you follow all instructions exactly as given.

All the fittings, measurements, recommendations and procedures are significant. Substitutions and approximations must be avoided, improper handling, maintenance, installation and adjustment, or service attempted by anyone other than a qualified technician, may void the future warranty claims and cause damage to the unit and/or result in injury to the operator and/or

bystanders.

y!_v_vf£q_ll_[€

• Destroy carton, plastic bags, and any exterior wrapping material immediately after the appliance is unpacked. Children should

never use these items for play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation.

• A child might suffocate if he crawls into the appliance to hide or play. Remove the door/lid of the appliance when not in use, even if you plan to discard the appliance. Many communities

have laws requiring you to take this safety precaution.

Child Safety

Proper Disposal of Appliance

_v_vf_4_]#II#B

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators or freezers are still dangerous

- even if they will sit for "just a few days". If you are getting rid of your old refrigerator or freezer, please follow the instructions below to help prevent accidents:

• Remove the door.

• Leave shelves in place so children may not easily climb

inside.

• Have the refrigerant removed by a qualified technician.

Risk of Child Entrapment

Record your Model and Serial Numbers

Record the model number and serial number of this appliance in the space provided below (the serial plate is located inside the cabinet compartment).

Model No. Serial No.

Installation Date Invoice Date

Start-up Date Telephone for Service

above) should be filled in completely, signed and returned to the address provided.

Electrical Information

These guidelines must be followed to ensure that safety mechanisms in the design of this appliance will operate

properly.

Avoid fire hazard or electric shock. Do not use an extension cord or an adapter plug. Do not remove any

prong from the power cord.

Grounding type walmreceptacle

Powersuppmy cord with 3-prong grounding pmug

• Refer to the serial plate for correct electrical rating. The power cord of the appliance is equipped with a three-prong grounding plug for protection against shock hazards. It must be plugged directly into its own properly grounded three-prong receptacle, protected with a 15 amp time delay fuse or circuit

breaker. The receptacle must be installed in accordance with the local codes and ordinances. Consult a qualified electrician. Receptacles with Ground Fault Circuit Interrupters (GFCI) are

NOT RECOMMENDED. DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG.

• If the voltage varies by 10 percent or more, appliance performance may be affected. Operating the appliance with insufficient power can damage the motor. Such damage is not covered under the warranty. If you suspect your voltage is high or low, consult your power company for testing.

• To prevent the appliance from being turned off accidentally, do not plug the unit into an outlet controlled by a wall switch or pull cord.

• DO NOT pinch, knot, or bend the power cord in any manner.

Other Precautions

• NEVER unplug the appliance by pulling on the power cord.

Always grip the plug firmly and pull straight out from the

receptacle.

• To avoid electrical shock, unplug the appliance before cleaning.

NOTE: Turning the control to "OFF" turns off the compressor but does not disconnect power to other electrical components.

CASTER INSTALLATION AND SET-UP

(Glass Door Only)

inspect the underside of the cabinet and packaging for damage such as a fork truck can cause. If hidden damage is found after uncrating, immediately call the delivery carrier and request an inspection. Retain all packaging and crating materials until the inspection is complete.

PARTS AND ACCESSORIES Check to make sure that you have received the box containing

all of the components listed below.

A CASTER RAiL (2) E WASHER (4) B LOCKING NUT (8) F SPACER PLATE (2)

C CARRIAGE BOLT (8) G SWIVEL CASTER (2) D BOLT (4) H FIXED CASTER W/ BRAKE (2)

TOOLS NEEDED

You will need the following tools to assemble and install the casters to the unit.

3/8" AND 1/2" INCH ADJUSTABLE WRENCH SOCKET WRENCH OR PLIERS

UNCRATING AND SET-UP

• Remove carton and all loose parts from inside of the unit.

• Carefully tip the unit onto its back with the help of an assistant. Lay the unit gently to rest on blocks to avoid damaging the

condensate drain hose and the plastic raceway that covers the evaporator tubing on the back of the cabinet.

• Remove and discard the wood skid from the bottom and the four (4) screws using a 3/8" socket wrench (see Fig. 1).

• Using a large adjustable wrench, remove and discard the two (2) black plastic leg levelers by turning it counterclockwise (see

Fig. 2).

SCREWS

Figure 1

1/2" INCH FIXED

WRENCH

LEG LEVELER

i!i

Figure 2

• Remove bottom door support bracket and screw opposite the door hinge using a 3/8" socket wrench (see Fig. 3).

DOOR

Figure3 "\

FRONT FIXED CASTER INSTALLATION

• Put two (2) carriage bolts through the rear (non-brake) side of the fixed caster and hold the carriage bolts loosely in place by

threading several turns on each of the locking nuts. Do not tighten the bolts yet.

• Hold the caster in position, insert the carriage bolt heads into slots A & B near the front of the caster rail and slide the caster

back.

• Insert the two (2) front carriage bolts thru the top side of the caster rail and then thru the front holes on the caster. Attach

locking nuts to each.

• Tighten all locking nuts securely using a 1/2 inch wrench (see Fig. 4).

• Repeat the same procedure for the other fixed caster.

REAR SWIVEL CASTER INSTALLATION

• Place a washer on one of the four long bolts and then feed the bolt through the hole in one of the swivel casters (see Fig. 6).

• Next, insert that same caster bolt through the hole on the metal spacer plate and then thru the rear hole of the caster rail (see

Fig. 7).

• Thread the caster bolt into the hole in the bottom-most foot pad on the unit.

• Tighten both top and bottom bolts securely using a 1/2 inch fixed or socket wrench.

• Repeat the same procedure on the left hand side. After installation, carefully tip the unit up with the help of an assistant.

Bolt .-__ ._

Washer.7_c_b

Caster ....

Swivel +_+_

Figure 6

Figure 7

BRAKE _9

FRONT OF NUTS

FIXED CASTER

CARRIAGE

BOLTS

SLOTS A&B

Figure 4

CASTER RAIL INSTALLATION

• Place a washer onto one of the four long bolts and slide bolt through the hole located just behind the fixed caster at the

front of caster rail.

• Align the caster rail assembly with the right hand side of the unit. Make sure the fixed caster is positioned toward the front of the unit.

• Align the bolt with the threaded hole in the front right foot pad of the unit. Thread the bolt into the hole until finger tight (see Fig. 5).

WASHER_

BOLT /

Figure 5

WASHER

,BOLT

+ 7 hidden pages