Friedrich VEA09K00SPE, VEA09K50SPE, VEA12K00RTE, VEA12K00RTG, VEA12K25RTB Owner’s Manual

Vert-I-Pak®

SinglePackageVerticalAirCenditieningSystem

A-Series
9,000 I 12,000 I 18,000 BTU/h

Installation& OperationManual

920-075-07 (10-03)

920-075-07(10-03)

TableofContents

GeneralSpecifications

InstallationRecommendations.......................................................................................................................................... 3

Model NumberIdentification Guide ................................................................................................................................... 4

VERT-I-PAKChassisSpecifications .................................................................................................................................... 4

IL

III.

IV.

V.

Installation

1. UtilityClosetDimensions................................................................................................................................................... 5

2. WallPlenum&ArchitecturalLouverInstallation................................................................................................................ 6

3. ElectricalInformation ..................................................................................................................................................... 7-9

4. IndoorReturnAirGrillelnstallation .................................................................................................................................. 10

5. DuctworkPreparationandCFM....................................................................................................................................... 11

6. ChassisInstallation.......................................................................................................................................................... 11

7. ChassisFinalConnections (Electrical,Duct,Drain& WallThermostat) ............................................................................ 12

8. FinalInstallationChecklist............................................................................................................................................... 12

ChassisOperation

9. ThermostatControl .......................................................................................................................................................... 13

10. LowAmbientProtection for Compressor& Fan................................................................................................................ 13

11. HeatingDefrost(HeatPumpModelsonly)........................................................................................................................ 13

12. FreshAirDoor................................................................................................................................................................... 13

13. CondensateDisposalSystem .......................................................................................................................................... 13

Service& Warranty

14. Servicing/ ChassisQuickChangeouts............................................................................................................................. 13

15. Warranty.......................................................................................................................................................................... 14

Ver_l-PakAccessories .................................................................................................................................................... 15

Please read this manual thoroughly prior to equipment installation or operation, it is the installer's
responsibility to properly apply and install the equipment, installation must be in conformance

with the NFPA 70-2002 National Electric Code or current edition and Universal Mechanical Code
current edition and applicable local or national codes.

Proper installation is not difficult but it is essential.

2

920-075-07 (10-03)

Vert-I-Pak Installation Recommendations

Forproperunitperformanceandmaximumoperatinglifepleaserefertothe minimuminstallationclearancesbelow.

Figure I

VERT-I-PAK ® units must be installed on an outside wall. Confined spaces and/or covered areas should be
avoided. Units should be installed no closer than 12" apart when two units are side by side. If three of more

units are to operate next to one another allow a minimum of 60" between units or pairs of units. Also, a vertical

clearance of 60" should be maintained between units. Units installed on the bottom floor should be mounted
at least 6" off of the ground.

SMALL RECESS OK 60" 60"

D D D

60" E

60" E

D D D

J

6" 7_

Figure2

Any time obstructions are present use
the following guidelines for proper

spacing from the VERT-I-PAK louver:

• For minor obstructions such as lamp
poles or small shrubbery aclearance

of 24" from the outdoor louver should
be maintained.

• For major obstructions such as a solid
fence, wall or other heat rejecting
device like a condensing unit, a mini-
mum distance of 72" should be kept.

6" 3

D D
D D

_A_

LARGER RECESS OK IF A> 5xB

\

D

D

60'_

D

D

BUILDING

OUTDOOR "72"
UNIT

MAJOR OBSTRUCTION

FENCE

H

12"

The above suggestions are for reference only and do not represent all possible installations. Please contact the factory
for information regarding affects of other installation arrangements.

By following these simple recommendations you can be confident that your Friedrich Vert-I-Pak ®will provide years

of worry-free operation.

3

920-075-07 (10-03)

Section I. GeneralSpecifications

MODEL NUMBER

SERIES

V=Vertical Series

E=Cooling with or without electric heat
H=Heat Pump

DESIGN SERIES

A = 32" Cabinet

NOMINAL CAPACITY
A-Series (Btu/h)

09 = 9,000
12 = 12,000
18 = 18,000

VOLTAGE

K = 208/230V-1Ph-60Hz

MODEL:

Voltage (V)

Refrigerant
Chassis Width

Chassis Depth
Chassis Height **
Shipping Wx D x H

Supply Duct Cellar***
Drain Connection

Min. Circuit Amps
CFM Indoor

Max. Duct ESP

V A

V(E,H)A09

230 / 208

R-22

23.125"

23.125"

32.25"

25,00" x 28,50" x35.00"

10"

3/4" FPT

.3 in. water

ENGINEERING CODE

OPTIONS

RT = Standard Remote Operation
SP = Seacoast Protected

ELECTRIC HEATER SIZE
A-Series

00 = No electric heat
25 = 25 KW
34 = 3.4 KW
50 = 5.0 KW

V(E,H)A12

230 /208

R-22

23.125"

23.125"
32,25"

26.00" x 28.50" x 35.00"
10"

3/4" FPT

See Chassis Nameplate

See Charts 2 & 3 (Page 10)

,3in.water

V(E,H)A18

230 /208

R-22
23,125"
23,125"

32.25"

26.00" x 28.50" x 35.00"

10"

3/4" FPT

,3 in. water

NOTES:

** Height includes 2" ductcollar & isolatorsunder unit.
*** Factory collar accepts 10" flex duct.

4

920-075-07(10-03)

II. Installation

1) UtilityClosetDimensions

Recommended utilityclosetdimensions anda typical indoorinstallationareillustrated inFigure 3. Three inches minimumclearance on

three sides of the unit must be allowed for return airflow, installationaccess and service access. See Figures 3 and 4 for clearances
and referencedimensions.

Figure3

25"x 20" Filter

(Field Supplied)

Typical Utility Closet

VPRG4 Access Panel and

Return Air Filter Grille

See Figure 8, Page 10
for return air options

Chassis Shownin Closet, on Optional Platform

Rigid Ductwork

Electrical

Connection

Flexible Ductwork

,VPAWP1-8/1-14

Wall Plenum

Plenum Divider

Wiring

Power

Disconnect

3/4" FPT Drain
Connection

• Vert-I-Pak Chassis dimensions:
23 _/e"wide x 23 _/_'deep x32 V4"high.

• VPAWP1-8/1-14 WallPlenumcut-out
dimensions24 SlY'wide x307/j, high.

• VPRG4 Access Panel cutoutdimensions:
27"wide by 553/4"high.

• See Figure9 (Pg11)for properchassis
installation.

Figure4

Top View f

7 tl

•2 wl

Optional
Platform

Chassis installs
23/e'' into Plenum

3" Clearance on all three sides

minimum for service and installation•

f

6t_

5

920-075-07(10-03)

2) Wall PlenumandArchitecturalLouverInstallation

A, Install the wall plenum (VPAWP1-8/1-14) components in accordance with the installation instructions provided with each accessory,

O IMPORTANT REMINDER: FRIEDRICH WALL PLENUM IS NOT DESIGNED TO CARRY STRUCTURAL

B, Ensure that the divider is adjusted propedy for the depth of the wail in accordance with the accessory installation manual

LOADS. PROPER WALL HEADER CONSTRUCTION IS REQUIRED. THE PLENUM REQUIRES
PROPER FLASHING, SHIM AND CAULK FOR A WEATHER RESISTANT INSTALLATION.

Figure5

WallPlenum& OutdoorLouverInstallation

Proper Header Caulk all 8

flange corners

Proper Flashing

InsideWall Plenum

Proper Caulking_

(Part B)

ProperCaulking

Architectural louver VPAL2 mounted
on the outside wall plenum (PartA)

• Rough opening dimension 24 %" wide x 307/8"high,

• Ensure that the bottom of the plenum is 3/4"fromthe floor of the closet,

• For proper airflow, maintain a minimum distance of 12" between Vert-I-Pak units (see Figure 1,page 3),
Consult the factory for any installation or application questions.

6

Proper Flashing

3) Electrical Data

Electrical Data

Model

Voltage (V)

LRA - Comp. (A)

Cooling Current (A)
MIN. Ckt. Amps (A)

Power Connection

Sample Nameplate (see your chassis nameplate)

230/208 230/208 230/208

21 21 21

4.4/4.9 4.4/4.9 4.4/4.9
15 20 30

HARD WIRED

920-075-07(10-03)

/

230/208 230/208 230/208

24.0 24.0 24.0

5.5/6.1 5.5/6.1 5.5/6.1
15 20 30

HARD WIRED

230/208 230/208 230/208

47 47 47

9.2/10.2 9.2/10.2 9.2/10.2
15 20 30

HARD WIRED

MODEL NO 1
SERIAL NO *

FRIEDRICH AIR CONDITIONING CO.
SAN ANTONIO r TEXAS

VOLTS: 24,33,34
VOLTAGE RANGE: 255-197

REFRIG CHARGE: 70ZS. R22
DESIGN PRESSURE: 575 PSIG HS/150 PSIG LS

COOLING: BTU/HR 8
SEER: 10 COP: 16
HEAT PUMP BTUIRR: 14

TOTAL COOLING AMPS: 9
TOTAL ELEC. HEAT AMPS: 15
ELECTRIC HEAT WATTS: 18

FOR PERMANENTLY CONNECTED UNITS ON

COMP'. PLA 11 LRA 12
MOTOR: FLA 13 RP 19

HEATER AMPS: 17
MIN. CKT AMP ~0 US

OR HACR TYPE CIRCUIT BREAKER.

GENERAL UNIT INFORMATION:

MAX OUTLET AIR TEMPERATURE: 2OO'F
MAX EXTERNAL STATIC PRESSURE ELECTRIC
HEAT'..5 IN. WATER

"O" CLEARANCE TO COMBUSTIBLE MATERIAL

USE ON SINGLE OUTLET CIRCUIT ONLY

WARNING

ELECTRICAL SHOCK AND

MOVING PARTS HAZARD

CAN CAUSE INJURY OI

PUL

BEFORE

SERVICING.

LISTED

120524

HEATING AND

COOLING EQUIPMENT

APPLICABLE PATENTS:

US 6,065,296

NY MEA NO.: 295-00-E

USE ONE OF THE

FOLLOWING ITEMS

TO COMPLETE THE

ASSEMBLY

WALL PLENUM:

VPAWP1 -8

VPAWPI -14

OUTDOOR GRILLE

VPAL2

INDOOR GRILLE

VPRGI
VPRG2

VPRG5

Important: all 208/230v chassis must be hard wired withproperly sized breaker. See nameplate for specific chassis

electrical requirements. See page 8- Figure 5 for unitwiring and wall thermostat wiring. See page 8for wire size. Use

HACR type breakers to avoid nuisancetrips. All field wiring must be done in accordance with nec and local codes.

3) ElectricalData (continued)

920-075-07 (10-03)

Figure6
Electrical Requirements

Note:All field wiring must complywith NEC andlocal codes.It

is the responsibilityof the installerto insurethat the electrical
codes are met.

Wire Size

Fuse/Circuit breaker indicated on unit'srating plate (See sample
Breaker on page 6), Proper current protection to the unit is

Grounding unit, orthrough separate ground wire provided on

Wire Sizing with local and national codes, NOTE: Use copper

Use ONLY wiring size recommended for single
outlet branch circuit.

Use ONLY type and size fuse or HACR circuit

the responsibility of theowner.

Unit MUST be grounded from branch circuit to

permanently connected units. Be sure that branch
circuit or general purpose outlet is grounded,

Use recommended wire size given in tables and
installa singlebranchcircuit. Allwidng mustcomply

conductors only.

Electrical RatingTables

NOTE: Use copper conductors ONLY, Wire sizes are per

NEC Check local codes for overseas applications

Recommended branch circuit wire sizes*

Nameplate AWG Wire size**

maximum circuit

breaker size

15A 14
20A 12
30A 10

AWG --American Wire Gauge
* Single circuitfrom main box

** Basedon copperwire, single insulatedconductor at 60°C

Electricshock hazard.

Turn OFF electric power before service
or installation.

All electricalconnectionsandwiringMUST

be installedby a qualified electrician and

conformtotheNationalElectricalCodeand
all local codes which havejurisdiction.

Failure to do so can result in property

damage, personal injury and/or death.

8

3) ElectricalData (continued)

Figure7
Electrical & Thermostat Wiring Diagrams

920-075-07 (10-03)

FOR 208VOLT MODELS ONLY:

MOVE THE WHITE WIRE AS

SHOWN BELOW

THERMOSTAT CONNECTIONS

(REAR)

RT2

THERMOSTAT

(FRONT)

DEFROST

COOL RELAY

COM. 208V 240V

TRANSFORMER

24V

T-STAT

HEATER

1

Note: the diagram above illustratesthe typical thermostat wiring and 208volt transformer wiring.

See the unitcontrol panel for the actual unit wiring diagram and schematic,

9

920-075-07(10-03)

4) IndoorReturnAirGrilleInstallation

There are three Indoor Return Air Grille options as shown in Figure 8, Choose the optionthat best suits your needs. Use the installation
instructions providedwith accessories for installation details,

Figure8

ReturnAir GrilleOptions

Option I

VPRG4

ReturnAir Grille with AccessPanel

A field-supplied(25"x 20")filteris
mountedinsidethehingedaccessdoor.

All Vert-I-Pak chassis are shipped with a

14x 20 filter installed. If an accessory filter
holder is to be used, you MUST remove the

VPRG2

_ ....... ReturnAir Grille

Unitrequiresa field-supplied

I

_ _ _\_ _÷ 16"x20" filter.

Notes:
A. These are the Friedrich recommended returnair grine /filter / access panel arrangements. Consultthe factory on other

arrangements. Improper return airarrangements will cause performance problems.

B. Return air arrangements areshown from the front, butcan also be installedfrom the right orleft sideof the unit.

accessdoororpanelanda

factory shipped filter from the chassis. Do
NOT use two filters

10

920-075-07(10-03)

5) DuctworkPreparation

1) Duct ESP:

To determine your system's indoorexternal static pressure
(ESE in inches of water) use a duct calculator (as provided

by your duct supplier). Include all flex duct transitions and
discharge grille(s). If flex duct is used, be sure all the slack

is pulled out of the flex duct. Flex duct ESP can increase
considerably when not fully extended. DO NOT EXCEED a

total of .30 ESP, as this is the MAXIMUM design limit for the
VERT-I-PAK A-Series unit.

2) Determining the Indoor CFM: Chart A - CFM

18000 12000/9000

.00 520 420
.10 510 410
.20 500 370

30 490 330

6) ChassisInstallation

Install the followingcomponents asshown in Figure 5.

A,

Ensurethat the wallplenumis installedinaccordance with

the VPAWP1-8/1-14 Installation Manual,

B.

Place the chassis intothe closet with the outdoor side

facing thewall plenum opening.

C.

Slide the chassis intothe wall plenum until the plenum
divider seal isestablished. (See Figure 9)

Figure9

Slide-in View/Chassis Installation

/

3) Correct CFM (if needed):
Chart B - Correction Multipliers

230V 1.00
208V 0.97

Heating 1.00

Cooling 0.95

TheVert-I-Pakchassismustbeinsertedintothewailplenumsothatthe
plenumdividergasketmakescontactwiththeplasticcondenserbaffleon
the unit.The chassiswill fit approximately23H' intothe wall plenum.

11

920-075-07(10-03)

7) ChassisFinalConnections

With the chassis in place,you are nowready to begin chassis
connections:

A. Move the thermostat switches to "OFF" and "AUTO." This

will keep the thermostat from cycling the chassis until final

connections arecomplete.

B. Connecttheductworkontothel0"coilar. Plasticwireties(field

supplied)are suggested to securethe ductworkinplace. Use
2 wire ties, onefor each inner and outer flex duct sleeve.

C. Using the two 3/4" plugs supplied with the unit,plug two of

the condensate drain holes. Connect a drain to the third
condensate exit location. Be sure to use teflon tape or

approved pipe sealant on all drain connections and plugs.
(See Figure 10.)

D. For208Voltpoweronly: youmustmovethetransformerwire

as shown inFigure 7, Page 9.

Electricalshockand moving parts hazard cancause injury
or death. Ifyou havenot done so, pull out the disconnect
headfound onthe front of chassis beforecontinuing instal-
lation! Disconnect external power at the breaker.

E. Review the Final Installation Checklist on Page 12 before

replacing the power quick disconnect, reconnecting power
tothe chassis, plugging inthe remote thermostat harness, or
operating the chassis.

Figure10
Drain Connection and Location

3*'

CAUTION

[] The unit basepan has three (3) provisions (left, right, and

rear) for connecting an external condensate drain.

[] A field supplied condensate drain system must be

connected to one of the three (left, right, or rear) 3/4"

FPT connections on the unit basepan. Use of rear fitting
may result in staining of the outside wall.

[] The remaining b,vo connections must be plugged using

the two 3/4" pipe plugs (provided) and field supplied
teflon tape or pipe joint compound.

[] The addition of a secondary drain pan may be required.

Follow all applicable codes.

[] Failure to follow these procedures may result in serious

property damage.

RT2 DigitalThermostat

8) FinalInstallationChecklist

[] Correct line voltage?

[] Chassis decklevel?

[] Plenum divider baffle installed?

[] Wall plenumcaulked? Level?Flashing?

[] HACR type breaker/fuse?

[] Single circuit only?

[] Ductwork connected?

[] Chassis weather seal in place?

[] Wall thermostatwired correctly?

[] Chassis insertedinto plenum?

12

920-075-07(10-03)

III. ChassisOperation

9) Remote Thermostat Control

Thechassisrequiresa simplesinglestageheat-coolwall thermostat.

Each chassis comes with a terminal strip located inthe electrical
control box. All internalchassiswiring (low&highvoltage) isfactory
ready for 230 Volt operation. For 208 Volt operation a singlewire

MUSTBE CHANGED ONTHE TRANSFORMER. Referto Figure
7 on page9.

10) LowAmbientProtection

Eachchassis isequippedwithLowAmbient Protectionintheform of
a suction linethermostat.This thermostat will prevent compressor
operation at low suction line temperatures. Each chassis is also
equipped with afactory installed bellows thatwill drainwater from
the base panto preventthe fan slinger fromfreezing during winter

weather.

11) HeatingDefrost (Heat PumpModels Only)

All Heat Pumps have a passive heating defrost system. Defrost
occursas neededand automaticallyswitchestoelectricheat during
defrost.When theoutdoor ambienttemperaturedropsbelowa 45°F
factory setting,the chassis automaticallyswitches to electric heat.
As outdoor ambient temperatures rise above 45°F, the chassis
returns to the heat pump mode. The changeover temperature
is user adjustable from approximately 32°F - 55°E The defrost
thermostat may also be used to lock out the compressor in an
emergency heat situation.

IV.Service& Warranty

14) Servicing/Chassis QuickChangeouts

The chassis isdesigned for quick disconnect and change out. For
minor electrical service, the control boxcover lifts straight upafter
the screws & disconnect headare removed. For major electrical,
refrigeration and fan service the chassis must be removed from
utility closet.

ToRemovethe Chassis from the Closet:

A Switch the wail thermostat off.

B Pullthe power disconnect located inthe frontof the chassis.

C Turnoff all powerto the unit at the main breaker or

disconnect.

D Disconnectthe thermostat wiring.
E Disconnectthe electrical connection.

F Disconnectthe ductwork.

G Disconnectthe drain connection.

H Slide the chassisout of thewall plenum.
I Lift the chassisout of the utility closet.

15) Warranty

All service work must be done by a qualified servicer. See
Warranty on the next page, and consult your dealer or contractor

for details.

12) FreshAir Door

The Fresh Air Door is an "intake" system. The fresh air door is
opened via a slide on the front of the chassis located just above
the indoorcoil. Move the slide left to open and right to close the
fresh airdoor. The system iscapable of upto 60 CFM of freshair
@ ~.3" H20internalstatic pressure.

13) CondensateDisposalSystem

The internal drain connections are 3/4" FPT fittings on the right,left
and outdoorside oftheunit.See Figure10onpage 12.The chassis
is designed with a condensate drain systemthat has 3 parts. The
three parts work asfollows:

Part 1: The system's first stage increasesenergy efficiency

utilizing a factoryinstalled fan that slings the cold
condensate ontothe hotoutdoor coil.

Part2: When high outdoor humidity preventsthe slinger from

disposing ofall the condensate, the excess condensate
overflows into the internaldrain connection.

Part3:

If Parts 1& 2 failfor any reason, excess condensate
overflows from aspillway directly intothe wall plenum
to the outside ofthe building. IF THIS OCCURS, THIS

ISYOUR WARNING THAT THE CHASSIS OR DRAIN

NEEDS SERVICING.

Electricalshock andmoving parts hazardcan causeinjury
or death. Pull out the disconnect headfound on the front

ofthe chassis before servicing.

Followall codes when working with the condensate drain
system. A secondary drain pan may be placed beneath the
chassis to preventcondensated spillage due to improper

installation or unit malfunction.

13

920-075-07 (10-03)

FRIEDRICH AIR CONDITIONING CO.

Post Office Box 1540 • San Antonio, Texas 78295-1540

[phone]. FAX [phone]

VERT- I-PAK ®A SERIES SINGLE PACKAGE VERTICAL AIR CONDITIONERS

LIMITED WARRANTY

SAVE THIS CERTIFICATE. it gives you specific rights, you may also have other rights which may vary from state to state and province

to province.

Inthe event that your unit needs servicing, contact your nearest authorized service center. If you do not know the nearest service center,
ask the company that installed your unit or contact us- see address and telephone number below. To obtain service and/or warranty parts
replacement, you must notify an authorized FRIEDRICH Air Conditioning Co. service center, disf_butor, dealer, or contractor of any defect

within the applicable warranty pedod.

When requesting service: please have the model and serial number from your unit readily available.

Unless specified otherwise herein, the following applies:
FRIEDRICH VERT-I-PAK A SERIES VERTICAL AIR CONDITIONERS AND HEAT PUMPS

LIMITED WARRANTY- FIRST YEAR (Twelve (12) months from the date of installation). Any part found to be defective in the material

or workmanship will be repaired or replaced flee of charge by our authodzed service center durleg the normal working hours; and
LIMITED WARRANTY - SECOND THROUGH FIFTH YEAR (Sixty (69) months from the date of installation). ON THE SEALED

REFRIGERATION SYSTEM. Any part of the sealed refdgeratiee system that is defective in material or workmanship wiUbe repaired or
replaced free of charge (excluding freight charges) by our authodzed service center dudng normal working hours. The sealed reffigerafiee

system consists of the compressor, metering device, evaporator, condenser, reversing valve, check valve, and the interconnecting tubing.

These warranties apply only while the unit remains at the original site and only to units installed inside the continental United

States, Alaska, Hawaii, Puerto Rico and Canada. The warranty applies only if the unit is installed and operated in accordance with

the printed instructions and in compliance with applicable local installation and building codes and good trade practices.

For international warranty information, contact the Friedrtch Air Conditioning Company - International Division.

Any defective part to be replaced must be made available to FRIEDRICH in exchange for the replacement part. Reasonable proof must

be presented to establish the dste of install, otherwise the beginning date of this certificate will be considered to be our shipment date plus
sixty days. Replacement parts can be new or remanufactured. Replacement parts and labor are only warranted for any unused portion

ofthe unit's warranty.

We will not be responsible for and the user will pay for:

1. Service ceils to:
A) Instruct on unit operation. B) Replace house fuses or correct house wiring. C) Clean or replace air filters. D) Remove the unit
from its installed location when not accessible for service required. E) Correct improper installations.

2. Parts or labor provided by anyone other than an authorized service center.

3. Damage caused by:
A) Accident, abuse, negligence, misuse, riot, fire, flood, or acts ofGod. B) Operating the unit where there is a corrosive atmosphere

containing chlorine, fluorine, or any damaging chemicals (other than in a normal residential environment). C) Unauthorized altera-

tion or repair of the unit, which in turn affects its stability or performance. D) Failing to provide proper maintenance and service. E)

Using other than a "Seacoast Protected" unit in a coastal environment. F) Using an incorrect power source. G) Faulty install_ee
or application of the unit.

We shall not be liable for any incidental, consequential, or special damages or expenses in connection with any use or failure

of this unit. We have not made and do not make any representation or warranty of fitness for a particular use or purpose and

there is no implied condition of fitness for a particular use or purpose. We make no expressed warranties except as stated in
this certificate. No one is authorized to change this certificate or to create for us any other obligation or liability in connection

with this unit. Any implied warranties shall last for one year after the original purchase data. Some states and provincesdo not

allow limitations on how long an implied warranty or condition lests, so the above limitations or exclusions may not apply to you. The provi-
sions of this warranty are in addition to and not a modification of or subtraction from the statutory warranties and other rights and remedies

provided by law.
In case of any questions regarding the provisions of this warranty, the English version will govern.

Rev 9-03

14

V. Vert-I-Pak Accessories

MODEL DESCRIPTION PHOTO

WALL PLENUM Two-part sleeve that telescopes inand
out from 5_/2"to 8" in depth. The wall plenum sits inside

VPAWP1-8

the exterior wall penetration.
DIMENSIONS: 303&"high x 24W' wide.
CUTOUT DIMENSIONS: 30W' high x 24_&"wide.

920-075-07(10-03)

VPAWP1-14

VPAL2

VPSC2

RT2

VPRG4

Same as VPAWP1-8, but telescopes 8" to 14" as required.

ARCHITECTURAL LOUVER Extruded aluminum louver
that attaches to the outdoor section of the wall plenum.

DIMENSIONS: 31 _/_6"high x 259h6"wide.

Same as VPAL2 but can be ordered in a special color to
match the exterior wall.

DIGITAL THERMOSTAT Digital electronic thermostat with
"one touch" adjustment. Mounts to wall for control of unit.

ACCESS PANEL / RETURN AIR GRILLE - Serves as
an access panel to chassis and interiorreturn air grille.

A field-supplied (25" x 20") filter is mounted insidethe

hinged access door.
DIMENSIONS: 58" high x 29" wide.
CUTOUT DIMENSIONS: 553/4" high x 27" wide.

VPRG2

RETURN AIR GRILLE - Interior return air grille that
hinges to allow a field supplied (16" x 20") filter to slip

inside. Must be used when an access door / panel
already exists in closet.

DIMENSIONS: 187h6"high x 223/8''wide.

_iqilf

15

FriedrichAirConditioningCo.
PostOfficeBox15401SanAntonio,TX78295-1540

4200N,PanAmExpresswayLSanAntonio,TX78218-5212

[phone]fax[phone]www,friedrich.com

Printed in the U.S.A. 920-075-07 (10-03)