Friedrich WE12C33D, US12D30B, WS10C30D, WS08C10D, US10D30B Brochure

THRU-THE-WALL

AIR CONDITIONERS

COMMERCIAL AND RESIDENTIAL GRADE

THE EXPERTS IN ROOM AIR CONDITIONING

WHEN SHOULD YOU INSTALL
A SOLID SIDE SLEEVE?

A solid-side wall sleeve allows for
installation in thick exterior walls where the
installation of room air units with side vents
would affect performance and may even void

the warranty.

ROOM AIR CONDITIONER

Blocked side vents restrict air ow.

FRIEDRICH THRU-THE-WALL

Solid-side sleeve (no side vents) can
be installed in thicker walls. Sleeve
can be positioned ush with exterior

wall.

Sleeve size

Applications

OVERVIEW

Perfect t for Fedder’s 27” sleeves Y —

Top-mounted controls Y —

Electronic controls Y Y

Programmable timer 24 hr. 24 hr.

Remote control Y Y

Auto-restart when power is

interrupted

Smart Fan auto adjusting fan Y —

Upward angled air discharge Y —

COMFORT & CONVENIENCE

Air ow direction control 4-way 6-way

Fan speeds 3 3

THRU-THE-WALL MODELS

WallMaster

Fits 27” sleeves Fits sleeves from

RESIDENTIAL OR

LIGHT COMMERCIAL

®

24 1/2” to 27”

RESIDENTIAL OR

LIGHT COMMERCIAL

Y Y

Uni-Fit

®

THRU-THE-WALL AIR CONDITIONERS

WallMaster®. A perfect fit in Friedrich and competitor’s
27” sleeves.

Commercial grade quality unit is ideal for installation in new
construction, retrots and remodels.

Perfect t in 27"

wall sleeves,

including Fedders A
and B* sleeves.

FITS SLEEVES

16 3/4" HIGH X 27" WIDE

WallMaster®

8000-15600 Btu

Up to 10.4 EER

WallMaster

Electric Heat

COOLING

9800-15600 Btu

Up to 9.8 EER

ELECTRIC HEAT

9100-11000 Btu

WallMaster

Heat Pump

COOLING

9000-12000 Btu

Up to 9.8 EER

HEATING

7500-9350 Btu

Up to 2.6 COP

®

®

Or with minimum intrusion into the
room.

Steel inner wall and extra dense

insulation

Vibration-isolating design and

components

TECHNOLOGY

Superior airflow design Y —

SOUND REDUCTION

®

ENERGY STAR

Environmentally friendly R-410A Y Y

EARTH

FRIENDLY

Energy saver switch Y Y

Washable, antimicrobial air lter Y Y

HEALTH

Stale air exhaust — Y

EntryGard™ anti-intrusion

protection

Insect barrier Y —

SAFETY

Slideout chassis Y Y

Power cord direction Left Right

Concealed power cord option Y —

Internal drain kit option Y —

Bafe adapter kit (for installation in

INSTALLATION

Fedders ‘B’ sleeves)

Condensate drain kit Y —

models Y Y

Y Steel inner wall

Y Y

Y —

Y —

COOL

Select MODE, FAN SPEED,
MONEY SAVER

TEMPERATURE and set the

TIMER.

NOTE: Chassis requires WSE sleeve for new installations (sold and shipped separately)

®

, adjust

COOL & HEAT

WSE wall sleeve ships
with weather panels
and grille.

Sleeve is shown at right with

standard galvanized steel
inner panel, painted steel
outer panel and standard

grille

Fits Fedders A & B sleeves. *B sleeve installations require BAK accessory, bafe adapter kit.

Inner steel weather panel WSE sleeve Outer weather panel Standard grille

2

3

WALLMASTER® FEATURES

THRU-THE-WALL AIR CONDITIONERS

Comfort & Convenience

• Easy-to-reach, top mount controls

• Remote control

• 24-hour timer

• Smart Fan auto-adjusts fan speed to
maintain desired temperature

• Check lter reminder

• 3-speed fan

• Auto restart

• Electronic defrost control

• Reversible louver allows a second
airow option

Energy Management

• Money Saver® setting saves money
by operating the fan only when

needed

• ENERGY STAR

• R-410A refrigerant

®

qualied models

Health and IAQ

• Washable, antimicrobial lter

Durability & Quality

• Rotary compressors provide quiet,
dependable performance

• Premium aluminum exterior grille

• Dense blower insulation

• Ried copper tubing

• Impact resistant front cover

• High tech ns with sine wave lanced
louvers increase energy efciency

by increasing surface area for heat

exchange

Ried copper

tubing

Sine wave

lanced louvers

Safety & Security

• EntryGard™ anti-intrusion protection
secures chassis to sleeve to deter ‘kick­in’ intrusion

• Power cord current leakage protected

• Insect barrier

Installation Features

• Mounts ush with the exterior wall

for a neat appearance

• Ideal for thicker wall installations,
where side ns don’t t

• Reversible louver allows for a second
airow option

• A high efciency replacement for 27”
sleeves including Fedders A and B*.
Sleeve measures 27” W x 16 3/4” H

Accessories

• WSE sleeve, ships with inside and
outside weather panel and standard

grille

• AG architectural grille for use with
WSE sleeve

• Bafe adapter kit for use with deep

sleeve installations

• Drain kit for condensate disposal

• Internal drain kit for new

construction applications where

condensate drain system is built-in

Uni-Fit® Universal fit for easy replacement in existing 24 1/2˝,
26” or 27” sleeves.

Residential grade quality for installation in new construction,
retrots and remodels.

FITS SLEEVES

24 1/2", 26" AND 27" WIDE

Uni-Fit

®

8000-13000 Btu

Up to 9.8 EER

Uni-Fit

®

Electric Heat

COOLING

8000-11500 Btu

Up to 9.6 EER

ELECTRIC HEAT

3850-11200 Btu

Angled air discharge for superior air
distribution when the unit is installed

low on a wall. Reversible louver for a

second air ow option.

Sleeve can be installed ush with
the exterior wall. Optional AG

architectural grille shown.

WallMaster® fits existing Fedders sleeves.

Sleeve Dimensions

Height (inches) 16 3/4 16 3/4 16 3/4

Width (inches) 27 27 27

Depth (inches) 16 3/4 16 3/4 19 3/4

Friedrich

WSE Sleeve

Fedders
A Sleeve

Fedders

B Sleeve*

Select MODE, FAN SPEED,
MONEY SAVER

TEMPERATURE and set the

TIMER.

®

, adjust

USC wall sleeve ships
with weather panels
and grille.

Sleeve is shown at right with

standard painted steel inner
panel, painted steel outer
panel and standard grille

COOL

Inner weather panel USC sleeve Outer weather panel Standard grille

COOL & HEAT

Chassis requires WSE sleeve (sold and shipped separately)
*Installation in Fedders B sleeve requires a bafe kit. See BAK accessory under accessories.

4

NOTE: Chassis requires USC sleeve for new installations (sold and shipped separately)

5

Model Height Widt h Depth

Depth

with

Front

Minimum
Extension
Into Room

Minimum

Exten-

sion

Outside

Thru-the-wall

Finished Hole

Height Width Max. Depth

WallMaster

®

WSE Sleeve 16 3/4" 27" 16 3/4" 23" 7 1/2" 9/16" 17 1/4" 27 1/4" 15 5/16"

Chassis 15 3/4" 26 1/2" 21" 22” – – – – –

Uni-Fit

®

USC Sleeve 15 1/2" 25 7/8" 16 3/4" 20 1/2" – 1/2" 15 3/4" 26 1/8" 16 1/4"

US Chassis 14 3/ 8" 24" 18 1/ 2” 20 1/8" 3 3/4" – – – –

UE Chassis 14 3/8" 24 5/8" 18” 19 5/8" 3 1/2" – – – –

UNI-FIT® FEATURES

THRU-THE-WALL OPTIONAL ACCESSORIES

Comfort & Convenience

• 6-way air ow control

• Remote control

• 24-hour timer

• Check lter reminder

• 3-speed fan

• Auto restart

• Defrost control

Energy Management

• Money Saver® setting saves money
by conserving energy

• ENERGY STAR

®

qualied models

• R-410A refrigerant

Health and IAQ

• Washable antimicrobial lter

• Stale air exhaust

Durability & Quality

• Rotary compressors provide quiet,
dependable performance

• Seacoast protection for corrosion
resistance in harsh environments

Installation Features

• Universal t trim ring

• Chassis designed to t 24 ½” to 27”

sleeves

• USC sleeve ts standard 26” sleeve

opening. See installation manual for

exact dimensions.

Accessories

• USC sleeve ships with expanded

aluminum grille

• Replacement grille ships with US/

UE chassis for use in existing sleeves
when a grille is needed

• UXAA architectural grille for use with
USC sleeve

WallMaster® 27” Sleeve Exterior Grilles

WSE SLEEVE

Standard Grille
Premium, stamped steel grille
with powder coat paint. Ships
with sleeve. Galvanized steel
inner and outer weather panels

also ship with sleeve.

WSE SLEEVE
Optional Architectural Grille- AG

Premium brushed aluminum

grille.

Installation Accessories (27” sleeve models only)

DK / Drain Kit
Installed at the back of the unit and allows for
attachment to condensate disposal system, if
necessary or desired.

IDK / Internal Drain Kit

New construction applications

where a condensate drain system

has been built into the wall interior.

IMPORTANT:

Operating the air conditioner

with incorrect rear grille or

without Bafe Adapter Kit
(on 19 3/4” deep sleeve) will
recirculate discharge air and
cause compressor overload

to trip.
This will cause the unit to shut

down temporarily and may
lead to premature compressor

failure.

BAK / Bafe Adapter Kit

Necessary when installing in a

sleeve deeper than 16 3/4" deep,
such as Fedders B sleeve
(19 3/4" deep).

CORRECT Vertical Louvers

INCORRECT Horizontal Louvers

Trim ring

IMPORTANT: 1” gap on sides and 1/2”

gap at top, which allows installation into

varying sleeve sizes, can be covered by
two-piece trim ring that ts over the
chassis front. Trim ring comes standard

with chassis.

NEW!

UXAA- Architectural grille for USC sleeve

Uni-Fit® installs in many existing sleeves.

Carrier

(51S

Series)

Sleeve
Dimensions

Height

(inches)

Width

(inches)

Depth

(inches)

NOTE: Chassis requires USC sleeve for new installations (sold and shipped separately)

6

Friedrich

USC Sleeve Amana

15 1/2 15 5/8 16 7/8 16 3/4 15 3/4 15 5/8 16 1/2 15 1/4

25 7/8 26 25 3/4 27 26 3/4 26 25 7/8 25 1/2

16 3/4 16 7/8 18 5/8 16 3/4 or 19 3/4 15 16 7/8 17 1/8 or 23 16, 17 1/2 or 22

Friedrich WSE

Fedders/

Emerson/

Emer-

son/

Fedders

GE/

Hot-

point Whirlpool

White-Westinghouse/

Frigidaire/ Carrier (52F

Series)

Uni-Fit® 26” Sleeve Exterior Grilles

Optional Architectural Grille UXAAUSC Sleeve Standard Grille

Sleeve/Chassis Dimensions

STANDARD GRILLE – Ships with USC sleeve

Expanded aluminum grille designed for use with USC sleeve.

REPLACEMENT GRILLE – Ships with US/UE chassis

Black plastic for use on existing sleeves without any grille.

IMPORTANT:

When installing into an existing sleeve, consult Installation
Section of your Installation/Operation Manual to determine
whether or not the grille needs to be replaced and/or a bafe
adapter should be used.

Trim ring

IMPORTANT:

US= 3 3/8”, UE= 2 7/8”

US chassis w/front fully installed into USC sleeve extends
into room 3 3/8”. UE chassis w/front fully installed into
USC sleeve extends into room 2 7/8”. 1” gap on sides and

1

/2” gap at top can be covered by two-piece trim ring that

ts over the chassis front

7

SPECIFICATIONS

Energy

Estar

Model Cooling Btu Heating Btu

WALLMASTER

Cool only

WS08C10D 8000 - 115 6.4 769 - - 10.4



WS10C10D 9700 - 115 8.2 990 - - 9.8 $89 - 2.4 260 WSE 103 107



WS12C10D 11500 - 115 11.5 1174 - - 9.8 $106 - 3.1 295 WSE 112 116



WS10C30D 10000/9800 - 230/208 4.5/4.9 1020/1000 - - 9.8/9.8 $92 - 1.5 260 WSE 101 105



WS12C30D 11500/11200 - 230/208 5.5/6.0 1174/1143 - - 9.8/9.8 $106 - 3.0 290 WSE 109 113



WS16C30 15600/15000 - 230/208 8.3/8.9 1835/1765 - - 8.5/8.5 $165 - 4.2 290 WSE 119 123

Heat Pump

WY09C33D 9300/9000 7500/7500 230/208 4.3/4.6 949/918 3.9/4.1 833/833 9.8/9.8 $85 2.6/2.6 2.1 260 WSE 103 107



WY12C33 12000/11800 9350/9200 230/208 6.1/6.4 1395/1372 4.8/5.1 1062/1010 8.6/8.6 $126 2.5/2.6 2.6 275 WSE 111 115

Cool with Electric Heat

WE10C33D 10000/9800 11000/9100 230/208 4.5/4.9 1020/1000 16.0/14.7 3550/2950 9.8/9.8 $92 - 1.5 260 WSE 104 108

WE12C33D 11500/11200 11000/9100 230/208 5.5/6.0 1174/1143 16.0/14.7 3550/2950 9.8/9.8 $106 - 3.0 290 WSE 107 111

WE16C33 15600/15000 11000/9100 230/208 8.3/8.9 1835/1765 16.0/14.7 3550/2950 8.5/8.5 $165 - 4.2 290 WSE 119 123

UNI-FIT

Cool Only

US08D10B 8000 - 115 7.4 810 - - 9.8 $73 - 2.2 260 USC 73 79



US10D10B 9800 - 115 9.2 1000 - - 9.8 $90 - 3.2 260 USC 78 84



US12D10B 11500 - 115 10.7 1170 - - 9.8 $106 - 3.8 TBD USC 80 87



US10D30B 10000/9800 - 230/208 4.7/5.1 1020/1000 - - 9.8/9.8 $92 - 3.2 285 USC 78 86



US12D30B 11500/11200 - 230/208 5.4/5.8 1170/1140 - - 9.8/9.8 $106 - 3.8 260 USC 80 87



US14D30B 13000/12600 - 230/208 7.0/7.5 1530/1480 - - 8.5/8.5 $138 - 4.0 310 USC 87 94

Cool with Electric Heat

UE08D11B 8000 3850 115 7.5 830 10.7 1230 9.6 $77 - 2.2 260 USC 73 79

UE10D33B 10000/9800 11200/9200 230/208 4.7/5.2 1060/1040 15.3/14.0 3500/2900 9.4/9.4 $96 - 3.2 285 USC 78 84

UE12D33B 11500/11200 11200/9200 230/208 5.6/6.0 1220/1190 15.3/14.0 3500/2900 9.4/9.4 $110 - 3.8 290 USC 80 87

®

®

Volts

Rated

Cooling

Amps

Cooling

Watts

Heating

Amps

Heating

Watts

Efciency

Ratio

EER

Estimated

Yearly

Energy

Cost COP

$69

Moisture
Removal
Pints/HR CFM Sleeve

- 1.2 250 WSE 93 97

ENERGY STAR® models



Weight

WallMaster Heat Pump heating information (shown in red) indicates heat pump heating performance. WallMaster Electric Heat heating information (shown in red)
indicates electric heat strip performance. For WallMaster Heat Pump electric heating performance refer to corresponding WallMaster Electric Heat model.

WALLMASTER HEAT PUMP

HEATING PERFORMANCE: Cha nge-over fro m heat pump operati on to resistanc e
operation on models indicated is automatic at a preset outside ambient temperature
of approximately 35°F.

Calculate the heat loss of the space to be heated. As long as the heat loss does
not exceed the resistance heating capacity rating of the unit, the heating perfor­mance will be satisfactory.

DEFROST CONTROL: Initiated at 30°F (outdoor coil temperature) and terminated
at 43°F (outdoor coil temperature). During defrost, the compressor stops and the
electric heat starts, then operates with the fan to maintain indoor comfort. Below
43°F, the unit remains in electric heat mode.

DEFROST DRAIN: Drain automatically opens at approximately 50°F to prevent
condensate from freezing inside drain pan.

Note: all models will produce condensate. If condensate disposal is desired, an
optional drain kit is available.

Net

Lbs.

Ship

Weight

Lbs

Plug Face/ Circuit Rating

Circuit

WallMaster

®

Model Number

WS08C10D, WS10C10D,
WS12 C10D

WS10C30D, W S12C30D,
WS16 C3 0

WE10C33D, WE12C33D,
WE16C33, WY09C 33D, WY12C3 3

®

Uni-Fit
Model Number

US08D10B, UE08D11B
US10D10B, US12D10B

US10D30B, US12D30B,
US14D30B

Rating

Breaker

or T-D Fuse

125V - 15A 5 - 15P 6

250V - 15A 6 - 15P 6

UE10D33B, UE12D33B 250V - 20A 6 - 20P 6

Plug

Face

(NEMA#)

Power cords are located on front left of WallMaster models and on front right of Uni-Fit models.

Due to continuing research in new energy-saving technology, specications are subject to change without notic e.

ENERGY STAR

As an
models meet the

®

partner, Friedrich Air Conditioning Co. has determined that the selected ENERGY STAR®

ENERGY STAR

®

guidelines for energy efciency.

Power

Cord

Length

(ft.)

Wall

Outlet

Appearance

Model

WallMaster

WSE Sleeve 18" 27 1/4" 18"

Chassis 18 1/2" 30 1/2" 29"

®

Uni-Fit

USC Sleeve 17 7/8" 28" 19 1/4"

US Chassis 17 1/4" 27 3/4" 22 1/4”

UE Chassis 17 1/4" 27 3/4” 22 1/4”

Your operating costs will depend on your utility rates and use. The estimated operating cost is based on a electricity
cost of $ .12 per kWh. For more information, visit www.ftc.gov/energy.

Friedrich Air Conditioning Co. l 10001 Reunion Place, Suite 500 l San Antonio, TX 78216 l 877.599.5665
www.friedrich.com

Commercial_Thru-the-wall_Air_Conditioners_Brochure_2014 Printed in USA

Carton Dimensions

Height Widt h Depth

®

INCHES