Franke LB9200 Installation Manual

INSTALLATION GUIDE

Little Butler® Hot Water Dispensing Faucets and Drinking Water Dispensing Faucets

DW5000 / LB5100 Series LB5200 Series DW6100 / LB6100 Series LB6200 Series

DW7000 / LB7100 Series LB7200 Series DW8000 / LB8100 Series LB8200 Series

KITCHEN
SYSTEMS

DW9000 / LB9100 Series

Rev 3 - 2/5/2014

LB9200 Series

TECHNICAL DATA

Recommended Pressure Range - 15 to 75 PSI

has certified that this faucet complies with NSF61 and NSF372 drinking
water system component requirements. These requirements meet California
Health and Safety Code requirements for low lead (AB1953) as well as the new
low lead requirements of the US Safe Drinking Water Act to go into effect in
January 2014

INSTALLATION INSTRUCTIONS

Remove all contents from the package and check for completeness.

1

NOTE: Call immediately if you see inconsistencies.

(1-800-626-5771) or visit

www.frankeksd.com

Installation Tools:

5/8” [16mm] - Mounting Nut

Drinking Water Series Faucets (DW_ _00)

1

4

2

3

Package Contents:

1 - Faucet

(item pictured may differ from
faucet you have. See front
cover for accurate illustration)

2 - Fastening Set

(1 - O-Ring)
(1 - Mounting Washer)
(1 - Mounting Spacer)

(1 - Mounting Nut)

3 - Cold Water Supply Tubing

(Black 3/8” poly-tube)

4 - Shut-off Valve

1

Installation

Little Butler® Series Hot only Faucets (LB_100)

1

Package Contents:

1 - Faucet

(item pictured may differ from faucet
you have. See front cover for
accurate illustration)

2 - Fastening Set

(1 - O-Ring)
(1 - Mounting Washer)
(1 - Mounting Spacer)

6

2

(1 - Mounting Nut)

3 - Cold Water Supply Tubing

(black 3/8” poly-tube)

4 - Heating Tank Supply Tubing

(red ¼”poly-tube – comes
pre assembled with faucet)

5 - Heating Tank Return Tubing

3

5

(high-temp silicone tube – comes
pre assembled with faucet)

6 - Shut-off Valve

4

Little Butler® Series Hot and Cold Faucets (LB_200)

Package Contents:

1 - Faucet

(item pictured may differ from faucet you have.
See front cover for accurate illustration)

2 - Fastening Set

(1 - O-Ring)
(1 - Mounting Washer)
(1 - Mounting Spacer)
(1 - Mounting Nut)

3 - Cold Water Supply Tubing

(2 -blue 1/4” poly-tubes)

4 - Heating Tank Supply Tubing

(red ¼”poly-tube - comes pre assembled with faucet)

5 - Heating Tank Return Tubing

(high-temp silicone tube - comes pre assembled
with faucet)

6 - 1/4” Tee Fitting
7 - Tee Tubing

(blue ¼” poly-tube)

8 - 1/4” x 3/8” Reducing Union Fitting
9 - Cold Water Supply Tubing

(black 3/8” poly-tube)

10 - Shut-off Valve

7

8

9

10

1

6

2

5

3

4

2

Installation

Franke recommends the installer familiarize themselves with how this dispensing faucet will
be installed and function as part of a point-of-use hot water, a filtration only drinking water,

2

or a combination hot and filtered point-of-use water dispensing arrangement BEFORE the
products are installed. Make certain to observe all local plumbing and building codes during
installation of this unit.

It is important to identify the dispenser to be installed as this guide applies to multiple
configurations. The hot water dispensing faucets are part of the Little Butler® Series.
There are 2 different styles of Little Butler® Series dispensers available:

The LB_200 Series dispensers offer hot and filtered water separately. These dispensers
must be used in conjunction with both a Franke heating tank unit and a Franke filtration
system. They utilize 4 tubes to connect to the system.

• 2 blue poly-tubes for the cold water supply into the dispensing faucet, which comes
from the filtration system.

• 1 red poly-tube to carry the filtered water from the dispensing faucet to the heating
tank unit.

• 1 opaque high temperature silicone tube to carry the heated water from the heating
tank back to the dispensing faucet.

The LB_100 Series dispensers offer hot water only. These dispensers are required to be
used in conjunction with a Franke heating tank unit. Use of a Franke filtration system in
addition to the heating tank is optional, but strongly recommended in order to prolong the
life and improve the performance of the heating tank, as well as providing much higher
quality water as compared to un-filtered water entering the tank. These models utilize 3
tubes to connect to the system.

• 1 black poly-tube for the cold water supply to the dispensing faucet, which
must come from the home water supply or from the filtration system (if utilized).

• 1 red poly-tube to carry the filtered water from the dispensing faucet to the heating
tank unit.

• 1 opaque high temperature silicone tube to carry the heated water from the heating
tank back to the faucet.

The filtered water only dispensing faucets are part of the Drinking Water Series, which are
designated as DW_ _00 models. These dispensing faucets will only be used in conjunction
with a Franke filtration system. There will only be one black poly-tube to connect the faucet
to the filtration system.

IMPORTANT: Customer MUST USE genuine Franke components (see below) in tandem
with all Franke dispensing faucets. Use of any filtration products, heating tanks, or
service parts other than genuine Franke components will VOID THE PRODUCT
WARRANTY in its entirety. Use of any Franke dispensing faucet with a Reverse
Osmosis Filtration system will also VOID THE PRODUCT WARRANTY.

Franke HT-200

Heating Tank

Franke FRCNSTR100

Filtration System

3

Franke FRCNSTR
Filtration System