Franke FLUENCE FF3200, FLUENCE FF3280 Installation Manual

LIMITED LIFETIME WARRANTY

All faucets installed in a private residence will carry a limited lifetime
warranty on all mechanical parts to be free of manufacturing defects
in material and workmanship under normal usage. All chrome finishes
carry a limited lifetime warranty; all other finishes are warranted for
five (5) years from the original date of purchase.

Marine and Outdoor Installation

warranted for Marine and Outdoor installations.

This warranty applies only to the original owner, providing the product
has been installed in accordance with our installation instructions,
used as recommended and in a normal residential application. In the
event of a warranty claim, the owner will be required to provide proof
of purchase - save sales receipt. This warranty covers all components
which make the product operational. Franke, at its option, may repair
or replace the product or components necessary to restore the pro­duct to good working condition. Franke reserves the right to inspect
the installation prior to the actual replacement of the product or com­ponent part. This warranty does not cover misuse or abuse, acciden­tal damages, scuffs or scratches, improper installation, abnormal
usage, negligence or damage caused by improper maintenance or
cleaning. Normal wear of parts is excluded from the warranty.
Damage caused by impurities or acts beyond our control are not
covered. Any product or part which has been repaired or altered in
any manner outside of Franke's factory, unless previously authorized
in writing by Franke, will void warranty. Any replacement excludes
transportation and any labor re-installation costs. This warranty
does not allow recovery of incidental or consequential damages such
as loss of use, delay, property damage or other consequential dama­ge, and Franke accepts no liability for such damages.

The Franke warranty is limited to the above conditions and to the
warranty period specified herein and is exclusive. Franke DISCLAIMS
all other warranties, expressed or implied, including IMPLIED
WARRANTIES OF MERCHANTABILITY AND/OR FITNESS
FOR A PARTICULAR PURPOSE. This warranty gives you
specific legal rights that may vary from state to state.

Further information

For any further information about our products, about the installation of

REV.0 02/2016

AC64IST591FUM5MWFS

STANDARD MAINTENANCE AND TROUBLESHOOTING

1. Shut o the water supply to the faucet.

2. Turn on the faucet briey to relieve any pressure inside the faucet.

3. Move the faucet handle to the “ OFF” position.

4.

Remove the plastic cover C from the handle A.

5. Remove the screw B using an allen key.

6. Pull the lever base A from the body .

7.

Unscrew the cap D.

8.

Unscrew the cartridge lock nut E.

9.

Lift ceramic disk cartridge F from the body and replace it with new
cartridge. Ensure the two lugs on bottom of the cartridge sit properly
in the allocated holes at the base of the body.

10. Re-assemble faucet in reverse order.

11. Test for leakage.

GENERAL MAINTENANCE

Clean aerator periodically for any buildup .
Do not use harsh detergents, solvents, chemical agents, metallic sponges,
etc. that could harm the surface and damage the nish.
Clean only with a soft sponge and soapy water.

SPARE / REPLACEMENT LIST

Franke Kitchen Systems
800 Aviation Parkway
Smyrna, TN 37167, USA
Phone: [phone]
Email: [e-mail]

them or about the guarantee, please contact our customer service
department:

the original purchaser of its faucets effective January 1, 2003.

: Franke faucets are NOT

Franke Kitchen Systems,LLC extends the following warranty to

REPLACING THE CARTRIDGE

**

Must specify finish

"CH" chrome
"SN" satin nickel

(i.e. F20001CH or F20001SN)

A+B+C Handle assembly

F20038**
F20039
F20040

E. Lock nut
F. Cartridge

G

. Washer G1/2"

F20034

F20044

O.

P.
Q.
R.
S.
T.

U.
V.

F20045

Sealing o-ring
Mounting hardware kit

Weight

Pull out hose
Nipple + Check valve
Pull out supply hose
Supply hoses
Plastic flange

F20046

D. Cap

F20047
F20048
F20049

F20017

F20037**

INSTALLATION MANUAL

FLUENCE

FF3200 Chrome
FF3280 Satin Nickel

J. Check Valve 1.75gpm

L+M+N.

Aerator + Aerator key

F20041**
F20042
F20043

F20006

G+J+K+L+M. Pull Down spray assembly

TECHNICAL DATA

NOTE:

CONTENTS IN BOX

INSTALLATION INSTRUCTIONS

1. Remove all contents from the package and check for completeness.

2.

Turn o water supply.

Recommended Water Pressure
Max. Water Pressure
Recommended Hot Water Temp.
Hole Size For Faucet

Certies this faucet complies with ASME A112.18.1 / CSA B125.1
& NSF 61, NSF 372 and AB1953

Flow Rate 1.6 GPM at 45 PSI

30-75 PSI

100 PSI
100° F

1 3/8”

1 Faucet assembly
2 Aerator key

3 Sealing o-ring
4

Pull out hose

5 Plastic flange
6 Rubber washer

7

Fixing plate

8

Fixing nut

9

Pull out supply hose

10

Weight
11 Screws
12 Supply hoses

3. Cut a mounting hole 1 3/8 diameter (35mm) in the desired position in
counter top or sink (if one isn’t available).

4.

Place the sealing o-ring (3) over the base of the faucet.

ATTENTION: The sealing o-ring should be sitting between the
countertop and faucet.

DO NOT use putty or other sealant at this location.

NOTES:

Solid surface i nstallation

: The countertop mounting sur face needs to
be at and free of debris otherwise the faucet may not sit properly.
For tile installations, avoid installing faucet near or on top of grout lines.
This may cause a weak joint between the faucet and the counter and
could cause leaks.

5.

Install the mounting hardware to the base of faucet body in

the following order - plastic flange (5), rubber washer (6),

fixing plate (7) as shown.

6. Tighten with the fixing nut (8) on the base of faucet body.

9. Connect the flexible supply hoses (12) to the water supply in the

house.

10. Remove the aerator using the aerator key (2), turn on water,
ush the faucet for any debris and check for leaks.
Reinstall the aerator and ensure ever ything is functioning properly.

7. Connect the pull out hose (4) to the pull out supply hose (9).

8. Place the weight (10) on the pull out hose (4) with the screws (11)

approximately 2” (50mm) above the bend in the bottom of the pull out
hose.

Contact us immediatly if you see inconsistencies.

Phone: [phone])
website: www.frankeksd.com

email: [e-mail]

ATTENTION: Be sure to hold pull out supply hose (9) steady when

connecting pull out hose (4), otherwise pull out supply hose (9)
can be loosened and possibly cause leaks.