Page 1
INSTALLATION GUIDE
Kitchen - FF2400, FF2460, FF2480
Bar/Prep - FFBP2400, FFBP2460, FFBP2480
KITCHEN
SYSTEMS
Page 2
TECHNICAL DATA
Standard Water Flow - 1.2 GPM at 45 PSI
Maximum Water Flow - 2.2 GPM at 60 PSI
Recommended Pressure Range - 15 to 75 PSI
has certified that this faucet complies with NSF61, AB1953 and ASME 112.18.1-2011/CSA
B125.1-2011 requirements
INSTALLATION INSTRUCTIONS
Remove all contents from the package and check for completeness.
1
NOTE:
Call us immediately if you see inconsistencies.
(1-800-626-5771)
or visit
www.frankeksd.com
info.fks@franke.com
1
6
4
2
8
Ŧ
Installation tools:
Package Contents:
1 - Mixer
2 - Fastening Set
(2) Rubber Washers
(1) Nut
3 - Counterweight (2)
4 - Aerator Wrench
5 - Check Valve
6 - Sprayhead
7 - Pull-Out Hose - Factory Assembly
8 - Hose Riser Assembly
(attached to mixer by installer)
9 - Riser Sealing Washer
Pre-Assembled in item 8
*
*
- Factory Assembly
Ŧ
5
9/16" [14mm] - Supply Hose
9
7
3
5/8" [16mm] - Hand shower hose
1-5/8" [41mm] - Fastening set
Screwdriver - Phillips #2 - Weights
2
Page 3
Installation
2
Flush the water supply to be sure it is free of
debris and then shut off the water supply.
Remove
check valve
3
4
Ensure O-ring is in place as shown to create
proper seal. If O-ring is missing, the faucet will
leak. Remove the check valve from the riser
swivel nut so the nut can be moved out of the
way. Install hose riser into mixer body. Use
wrench to tighten. Reinstall the check valve and
sealing washer onto the swivel nut, hand tight.
Before inserting the mixer in the hole in the sink
or counter top, make sure that the rubber washer
is properly positioned in its seat. Place the mixer
in the hole, orienting the spout toward the sink
bowl.
Note: Hole should be 35mm (1-3/8”) minimum
diameter
O-ring
Position
wrench
on hose
riser flats
Swivel nut
5
Install fastening set as shown: rubber washer
and threaded washer/nut. Tighten the
washer/nut with wrench.
DO NOT ROTATE MIXER BODY
to tighten the threaded nut.
Only tighten with wrench from the underside
of sink.
Rubber
Washer
Rubber
Washer
Washer/Nut
3
Page 4
Installation
6
7
Connect the hand shower hose to the check
valve at the end of the riser. Make sure the
sealing washer is placed between the check
valve and the hand shower hose. Tighten with
wrench.
Plumber / Installer must test and
confirm that all hoses, hose riser and
check valve connection seals are
water tight.
Attach the weights (2) to the hand shower hose at a
suggested distance of 22" [560 mm] from the hose
riser connection. The weights must be attached as
close together as possible. Plumber / Installer
must test and verify the correct distance. Care
must be taken in positioning of the weights so the
hand shower hose does not kink.
M15X1
Hand
shower
hose
Sealing
washer
&
check
valve
22"
[560 mm]
8
Connect the flexible supply hoses to the supply
valves. Turn on the water supply and check for any
leaks
4
Page 5
Usage
1
2
3
The mixer can be installed with the handle
positioned on the right or the left thanks to
360 degree spout rotation.
If the handle is installed on the right side hot
water is obtained by moving the lever forward
and cold water by moving it backward and
water flow is turned on by moving handle to
right.
If the handle is installed on the left side hot
water is obtained by moving the lever
backward and cold water by moving it forward
and water flow is turned on by moving the
handle to the left.
COLD
back
HOT
front
ON
HOT
back
COLD
front
4
ON
Pull out hand shower supplies two different jets
by sliding the button on the front side.
5
Page 6
1
MAINTENANCE
Replacement Parts
1 - F2401CH Lever Handle - chrome
1 - F2401OWB Lever Handle - old world bronze
1 - F2401SN Lever Handle - satin nickel
2 - F2402 Cartridge
3 - F2403CH Valve Kit - chrome
3 - F2403OWB Valve Kit - old world bronze
3 - F2403SN Valve Kit - satin nickel
4 - F2404 Fastening set
7 - 2407CH Hand shower - chrome (kitchen)
7 - 2407OWB Hand shower - old world bronze (kitchen)
7 - 2407SN Hand shower - satin nickel (kitchen)
12
3
7
2
7 - 2411CH Hand shower - chrome (bar/prep)
7 - 2411OWB Hand shower - old world bronze (bar/prep)
7 - 2411SN Hand shower - satin nickel (bar/prep)
8 - 2408 Pull-out hose
9 - 2409 Counterweight
10 - 2410 Check Valve Assembly
11 - 2412 Hose Riser
5 - F2405 Supply Hose
6 - F2406 Aerator & Wrench
12 - 2413 1.75GPM Flow Restrictor
Brand and
5
Certification
marks
1
6
11
4
9
10
2
Before carrying out this operation make sure that water supply is turned off.
If the supply is off unscrew the aerator using the wrench supplied and remove it from its seat. If the aerator
is clogged rinse it with running water without using detergents. If aerator is damaged replace it and
assemble everything in the opposite sequence.
Aerator Cleaning / Replacement
8
backside
Marks on
backside when
lever is installed
right side
6
Page 7
3
Make sure water supply is turned off before maintenance.
Unscrew set screw (1) to remove lever handle. Unscrew the screw (2) to remove handle
extension (3). Lift off the dome (4) and the friction washer (5). Using a wrench unscrew the
cartridge nut (6) and remove. Remove the large O-ring (7) from the nut (6) and replace with new
O-ring. Remove the damaged cartridge (8) from the mixer body and discard cartridge.
Put the new cartridge into the body with the two positioning pins aligned with two seats (9) and
reassemble everything in the opposite sequence . Be sure to test for leakage.
Cartridge Replacement
1
2
3
5
9
8
6
4
9
6
7
7
Page 8
LIMITED LIFETIME WARRANTY
Franke Consumer Products, Inc., Kitchen Systems Division extends the following warranty to the
original purchaser of its faucets effective January 1, 2003.
All faucets installed in a private residence will carry a limited lifetime warranty on all mechanical
parts to be free of manufacturing defects in material and workmanship under normal usage. All
chrome finishes carry a limited lifetime warranty; all other finishes are warranted for five (5)
years from the original date of purchase.
Marine and Outdoor Installation: Franke Consumer Products, Inc. faucets are NOT warranted
for Marine and Outdoor installations.
This warranty applies only to the original owner, providing the product has been installed in
accordance with our installation instructions, used as recommended and in a normal residential
application. In the event of a warranty claim, the owner will be required to provide proof of
purchase - save sales receipt. This warranty covers all components which make the product
operational. Franke, at its option, may repair or replace the product or components necessary to
restore the product to good working condition. Franke reserves the right to inspect the
installation prior to the actual replacement of the product or component part.
This warranty does not cover misuse or abuse, accidental damages, scuffs or scratches,
improper installation, abnormal usage, negligence or damage caused by improper maintenance
or cleaning. Normal wear of parts is excluded from the warranty. Damage caused by impurities
or acts beyond our control are not covered. Any product or part which has been repaired or
altered in any manner outside of Franke's factory, unless previously authorized in writing by
Franke, will void warranty. Any replacement excludes transportation and any labor
re-installation costs. This warranty does not allow recovery of incidental or consequential
damages such as loss of use, delay, property damage or other consequential damage, and
Franke accepts no liability for such damages.
The Franke warranty is limited to the above conditions and to the warranty period specified
herein and is exclusive. Franke DISCLAIMS all other warranties, expressed or implied, including
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
This warranty gives you specific legal rights that may vary from state to state.
Further information
For any further information about our products, about the installation of them or about the
guarantee, please dial the number of the customer service:
Phone number +1-215-822-6590
Or: 1-800-626-5771
Fax number + 1-215-822-5873
Franke Consumer Products Inc. - Kitchen Systems Division
3050 Campus Drive, Suite 500 Hatfield, PA 19440
8
Loading...