Franke FAK 607 XS Handbook
1
HANDBOOK HOOD FAK607XS ACTIVE 9925093 110.0023.303
UPDATED DECEMBER 2009
MOTOR NR 01 POWER IMPUT : 340 W
SPEED : 4+INTENSIVE
LIGHTING : 20 W X2 HALOGEN LAMPS
TOTAL POWER : 340 W
IMPUT VOLTAGE : 230V 50 HZ
CONTROLS : electronic
I 270/260 290 75 45
II 360/340 360 155 51
III 570/510 450 215 60
IV 730/660 480 300 65
Int 820/720 500 340 67
Speed Extraction Pressure Power Sound
Rate Input Power
IEC 61591 Maximum IEC 60704-2-13
[M
3
/H] [Pa] [W] [dB(A)]
1 2
1 (200 m3/h, 5 Pa) Resistance curve according to IEC61591
2 (200 m
3
/h, 15 Pa) Resistance curve according to IEC61591
Model FAK 607 XS
FUN Number 110.0023.303
Hood type Wall
Width 60cm
Control type Electronic
Finish StainlessSteel
Extraction speed setting 4 + int.
Automatic cut-off timer
Continuous 24 hour ventilation
Digital Display
Filtering function
Motor Energy
Filter type A
Perimetric extraction
Easy fit
Remote control Optional
Filter saturation indicator
Illumination Halogen 2 x 20W
Comfort light
Grease filter Aluminium cassette
Outlet tube diameter 150mm (120mm adaptor supplied)
db at 400m3/h
Recommended positioning 250mm Electric
4
ELECTRICAL CONNECTION •
Connect the hood to the mains through a two-pole switch having a contact gap of at least 3
mm.
• Remove the grease filters being sure that the connector of the feeding cable is correctly
inserted in the socket placed on the side of the fan.
Metal grease filters
Metal filters can be washed also in a dish machine. They need to be washed every
time a drop-symbol appears in the display or at least every two months. In case of
very frequent use these have to be washed even more often. Alarm reset • Press
the G-key for at least 2 seconds.
Cleaning
• Open the comfort panel.
• Remove the filters one by one by pushing them backwards and pulling them
down contemporaneously.
• Wash the filters. Pay attention not to bend them. Make sure that filters are
completely dry before putting them into their seat. (a possible modification of the
filter surface doesn’t influence its efficiency).
• Place the filters again into their seats and make sure that the handle of the filter
remains outside.
• Close the comfort panel.
5
CONTROL BOARD
Key Function Displ
ay
A Switches the extractor motor on and off at the latest
selected speed
Indicates the selected speed.
B Decreases the suction speed.
C Increases the suction speed.
D By pressing this key it is possible to activate the
intensive speed from any previously selected speed.
The intensive speed can be activated even when the
motor is OFF. This speed has been timed at 10
minutes. After that time the system activates automatically the latest selected speed. This function is
suitable for cooking conditions when vapours and
smells are of the utmost emission.
HI appears. The spot down on the right side flashes once a
second.
E By pressing this key it is possible to set up the motor
to a suction speed at 100 m3/h lasting 10 minutes
every hour. After this the motor switches off automatically. When the filter saturation is going on it is
possible to reset the alarm by pressing this key for
about 3 seconds. The indication is visible only when
the motor is off.
Indicates the 24-function. The spot down on the right side
flashes and the motor is on.
Once the process is finished the previous indication
disappears: FF Indicates that the metal grease filters saturation alarm has been triggered, and the filters need to be
washed. The alarm is triggered after 100 working hours. EF
Indicates that the charcoal filter saturation alarm has been
triggered, and the filter has to be replaced; the metal grease
filters must also be washed. The charcoal filter is triggered
after 200 working hours.
F By pressing this key it is possible to set the delayed
shutdown of the appliance to 30 minutes. This function is suitable for a complete elimination of the residual smells. It can be activated at any position, and
it is deactivated by pressing the key again or by
switching off the motor.
Indicates alternately the selected speed of the hood and the
time left before the hood shutdown. The spot down on the right
side flashes.
G Turns light on and off. When pressed for about 2
seconds the upper lighting switches on (only in the
90 cm hood version).
H Turns light on and off at reduced intensity.
6
COMFORT PANELS
Remove the comfort panels pulling them slightly.
• It is recommended to use a neutral detergent liquid and a damp cloth when washing the
outer surface of the comfort panel.
• Wash the inner part of the panel as well by using a neutral de-tergent liquid and a damp
cloth; in any case do not use wet sponges or other clothes nor water jet or corrosive
detergents.
• Let the get dry, and place them again in their correct position.
CHARCOAL FILTER
• This filter cannot be washed or regenerated. It must be replaced when the EF appears
on the display or at least once every 4 months. Activation of the alarm signal
• In the recycling version hoods the filter saturation alarm must be activated during the
instal-lation or later.
• Switch off the hood and the lights. • Disconnect the hood from the mains supply.
• When restoring the connection press and hold B-key.
• When releasing the key two rotating rectangles appear on the display.
• Within 3 seconds press the B-key until a flashing confirmation appears on the dispaly:
• 2 flashes with EF - charcoal filter saturation alarm ACTIVATED
• 1 flash with EF - charcoal filter saturation alarm DEACTIVATED.
REPLACING THE CHARCOAL FILTER
Reset of the alarm signal • Switch off the hood and the lighting. If the 24h-function has been
activated this has to be deactivated.
• Press the E-key until the display is unlit. Replacing of the filter
• Remove the comfort panels pulling them slightly.
• Remove the grease filters.
• Remove the saturated charcoal filter as indicated (A).
• Place the new filetrs as indicated (B).
• Put the metal grease filters into their seats.
• Place the comfort panels into their seats again.
Loading...