FD 404A1
High-Capacity Air Jogger
7/2013
OPERATOR / PARTS MANUAL
FIRST EDITION
TABLE OF CONTENTS
SUBJECT PAGE
DESCRIPTION 1
SPECIFICATIONS 1
UNPACKING 1
SAFETY 1
FEATURES & CONTROL PANEL 2
OPERATION 3
BASIC JOGGING 3
PAPER TRAY TILT ADJUSTMENT 3
USING THE TIMER 4
TROUBLESHOOTING 4
DAILY MAINTENANCE 4
PARTS LIST 5
DESCRIPTION
FUNCTION
The FD 404A1 High-Capacity Air Jogger aligns and dries printed
sheets in a single process while reducing static electricity.
Variable vibration speed and air pressure controls combine to
reduce jogging time, allowing press sheets and digital printouts
to be air-dried immediately.
SPECIFICATIONS
Variable Vibration Speed: Up to 3,000 vpm
Variable Air Control: Up to 29,000 rpm
Bin Size: 3.75” D x 20.375” W
Media Size: 5” x 7” Min up to 12” x 18” Max
Sheet Capacity: Up to 940 sheets 20#
Dimensions: 21” W x 18” D x 54” H
Weight: 100 lbs.
Voltage: 110V/120V, 50/60 Hz
UNPACKING
1. Check package for shipping damage. If there is shipping damage, do not discard the box.
2. Remove the machine and packed components from the box, includes power cord and manual.
SAFETY PRECAUTIONS
• Place the machine on a level and stable surface, to prevent it from falling over and causing personal injury
or damage to the machine. Avoid locations with direct sunlight, excessive dust and/or dirt, chemicals, salt or
vibrations.
• Connect the power plug to a grounded outlet and do not use any other voltage other than specied on the serial
plate. Do not share a wall outlet with another piece of equipment as overheating could occur. Be sure to route the
power cable to the wall outlet in a way which will prevent people from tripping over it.
• When cleaning the machine, turn off the power rst, then unplug from the wall outlet.
• Do not dismantle or attempt to repair the machine. Do not lubricate or apply grease to the machine. Call for
service.
1
FEATURES & CONTROL PANEL
1
6
2
10
3
11
7
8
9
Control Panel
4
5
No. NAME FUNCTION
1 Paper Tray Holds paper for jogging
2 Tray Tilt Adjustment Knob Used to alter the tilt angle of the paper tray
3 Control Panel Controls all functions of the jogger
4 Main Power Switch Turns the powere on or off
5 Foot Pedal Used for hands-free operation
6 Timer Adjustment Knob Choose jogging duration, from 0-60 seconds
7 3-Way Power Switch Power on. Power off, Foot pedal operation
8 Timer Off/On Switch Toggles between timed and untimed jogging (I = on, O = off)
9 Fuse (3A) Fuse for jogging
10 Air Adjustment Knob Turn right for stronger air pressure, turn left for less air, all the way left
for no air
11 Jog Speed Adjustment Knob Turn right for increased vibrations, turn left for decreased vibrations
2
OPERATION
Basic Jogging
When the AIR adjustment knob is turned to the right (ON), air blows through vents in the paper tray while the
machine is operating.
When the JOG adjustment knob is turned to the right (ON), the paper tray vibrates.
For jogging regular paper, both switches should be set to ON, while the air-only option can be used to loosen
paper or dry ink.
Power Switch
Setting
ON OFF Jogger operates continuously
ON ON Operation begins immediately
FOOT OFF Jogger operates continuously once foot switch is pressed
FOOT ON Operation begins by stepping on the foot switch
Timer Setting Result
Paper Tray Tilt Adjustment
1. Hold the lower center of the paper tray. NOTE: Keep hands and ngers away from the lower portion of the
paper tray to avoid injury.
2. Loosen the tilt adjustment knob and adjust tilt angle.
3. Tighten adjustment knob. Be sure it is well tightened so it won’t become loose during jogging.
In general, the paper tray is tilted vertically for thick paper (Fig. 1). For thin paper, set the paper tray horizontally
to prevent the paper from being bent and folding over. (Fig. 2).
Fig. 1
Tilt Adjustment Knob
Keep ngers away from this area
Fig. 2
when adjusting tilt angle
3
Using the Timer
1. Set Timer switch to on (I).
2. Turn the Timer Adjustment Knob to the desired length of time you wish to jog. Choose from 0 to 60 seconds.
3a. Standard operation: Set the timer switch to the on position and set the three way switch to the on position, air
llow and vibrations begin when the is stepped on. Jogging and air ow will stop when the set time has passed.
3b. Foot Pedal operation: Set the timer switch to the on position and set the three way switch to FOOT, air ow
and vibrations begin when the foot switch is stepped on. Jogging and air ow will stop when the set time has
passed.
TROUBLESHOOTING
TROUBLE POSSIBLE CAUSE REMEDY
Paper is not jogged
completely
Air ow is weak Air adjustment knob is set to
Paper is a non-standard size Jog it while loosening it by hand.
Paper has static electricity Add some space between the sheets by
hand.
Too much paper in paper tray Reduce the volume of paper jogged at one
time.
Turn knob to the right to increase air ow.
low volume
Paper or paper scrap is lodged
in air inlet or outlet
If air ow problem is not xed following these suggestions, blower
maintenance may be required. Call for service.
No air is discharged Air adjustment knob is set to
OFF
Fuse is blown Replace Fuse
If the fuse is blown again after replacement, the cause may be within the
machine. Call for service.
Paper tray will not vibrate Jogger adjustment knob is set
to OFF
Fuse is blown Replace Fuse
If the fuse is blown again after replacement, the cause may be within the
machine. Call for service.
DAILY MAINTENANCE
Clear air inlet and/or outlet.
Turn knob to the right to increase air ow.
Turn knob to the right to increase vibrations
Clean the air outlet vents in the paper tray to remove paper scraps or dust.
4
PARTS
10
3
1
2
4
8
5
6
9
7
ITEM # PART # DESCRIPTION QTY
1 RDD-019P BOLT 2
2 RDD-031P TILT ADJUSTMENT KNOB 2
3 RDD-030P TILT ADJUSTMENT KNOB NUT 2
4 SEE NEXT PAGE CONTROL PANEL 1
5 RDD-020P BODY SIDE PANELS 2
6 RDD-021P POWER SWITCH 1
7 RDD-022P FOOT PEDAL 1
8 RDD-023P RUBBER FEET 4
9 RDD-024P BOTTOM PANEL 1
10 RDD-036P FRONT PANEL 1
5
1
4
2
3
ITEM # PART # DESCRIPTION QTY
1 RDD-003P TIMER SWITCH 1
2 RDD-004P AIR BLOW ADJUST KNOB 1
3 RDD-005P JOG SPEED ADJUST KNOB 1
4 RDD-006P ON / OFF / FOOT POWER SWITCH 1
5 RDD-007P TIMER ON-OFF ROCKER SWITCH 1
6 RDD-008P FUSE HOLDER 2
5
6
6
1
4
9
2
5
10
3
6
7
8
ITEM # PART # DESCRIPTION QTY
1 RDD-025P MOTOR CASING 1
2 RDD-026P SCREWS 10
3 RDD-027P POWER PLUG INLET 1
4 RDD-028P TOP REAR PANEL 1
5 RDD-029P LOWER REAR PANEL 1
6 RDD-013P SOUND REDUCTION PAD 1
7 RDD-014P FAN MOTOR 1
8 RDD-015P RUBBER BOOT 1
9 RDD-001P CONTROL BOARD A 1
10 RDD-002P CONTROL BOARD B 1
7
2
3
5
1
4
6
9
1
ITEM # PART # DESCRIPTION QTY
1 RDD-026P SCREWS 8
2 RDD-032P BACK WALL BOLT 6
3 RDD-034P BACK WALL 1
4 RDD-035P AIR CANISTERS 2
5 RDD-009P MOTOR 1
6 RDD-012P BRACKET 1
7 RDD-011P BRACKET SCREW 2
8 RDD-010P BLOWER BOX 1
9 RDD-016P MOTOR MOUNT 1
10 RDD-017P RUBBER MOUNT 3
11 RDD-018P RUBBER BLOWER TUBE 2
7
8
10
11
12
13
8
Loading...