Foredom H15SJ User Manual

LIMITED WARRANTY

The Foredom Electric Company warrants its product to be free of
defects in material or workmanship for a period of 90 days after
purchase. During the warranty period, the defective product will be
repaired or replaced without charge or, at our option, the purchase
price will be refunded. This warranty does not cover damage caused
in transit or by accident, misuse, or ordinary wear.
WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OF FITNESS
AND MERCHANTABILITY,ARE HEREBY LIMITED IN DURATION TO A PERIOD

NDING 90 DAYS FROM DATE OF PURCHASE, AND WE WILL NOT BE LIABLE

E
OR RESPONSIBLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES.
or replacement will be made at our option if the product is returned
post-paid to:

The Foredom Electric Company

16 Stony Hill Road, Bethel, CT USA 06801

All warranty repairs must be done at the factory at the above address.
We will not pay any shipping or transportation charges.This warranty
only covers the original purchaser of the product. Some states do not
allow limitations on how long an implied w
limitations may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state
to state.

FOREDOM

The Foredom Electric Company

16 Stony Hill Road, Bethel, CT 06801 USA • www.foredom.com
Phone: [phone] • Fax: [phone]

Form No. 1233 n 3/10 Printed in USA

®

ALL IMPLIED

Repair

arranty lasts, so the above

Instructions for Foredom Hammer Handpieces
H.15, H.15D, and H.15SJ

Hammer Handpieces are supplied with an anvil point (HP10177).

If anvil points are reshaped they must also be polished with a
grinding wheel or sandpaper.

Operation:

from 0–5,000 RPM (or intermittently up to 7,500 RPM). Use at higher
speeds will create excessive heat which will damage the handpiece.

Changing Points: Insert the pin through the cross hole in the anvil
or carbide stylus point. Hold the handpiece firmly and unscrew the point
in a counterclockwise direction. (Right hand thread.) A new point can be
installed by threading it into the nosepiece and tightening it with the pin.

Adjusting Impact: The impact of the stroke is adjusted by turning the
knurled ring on the handpiece– counterclockwise towards the tip for a
lighter impact– and clockwise towards the back of the handpiece for a
heavier impact.

Lubrication: Before disassembling nosepiece, be sure to clean off any
dirt or other foreign matter to prevent it from falling inside the handpiece.
Lubricate after every 10 hours of use.Apply no more than 2 drops of oil into
the oiling hole located on the barrel of the handpiece and into the hole on
the rear of the duplex spring connection of the H.15D.

Several other hammer tips are shown inside and are available separately.

Always wear safety glasses when using power tools.

The H.15, 15D, and 15SJ handpieces can be operated at speeds

Accessories for Hammer Handpieces

Made in USA. 0-5,000 Strokes per Minute Max Speed.

The six new threaded anvil points fit Foredom Flex Shaft Hammer Handpieces,
Foredom Micromotor Hammer Handpiece and the Swiss made Badeco Hammer
Handpiece
finished with black oxide.

Threaded Anvil Points for Hammer Flex Shaft and Micromotor Handpieces

Ball Nose
(2.35mm) dia.

Fine Point
(.4mm) dia.

Square
(2.35mm)

Cylinder
(6mm) dia.

Rectangle
(2.35mm x 4.8mm)

Bezel Rocker
(8mm x 6.4mm)

They are heat treated steel made to the finest specifications and

.

3/32″

.015″

3/32″

7/32″

3/32″ x 3/16″

5/16″ x 1/4″

HP10171

HP10172

HP10173

HP10175

HP10176

HP10179

Other Foredom Hammer Tips
for H.15, H.15D, and H.15SJ
Handpieces

Carbide Stylus HP10212
4-48UNF-2A thread

AK101

6-Pc Anvil Point Kit

Includes: Ball Nose, Fine

Square

oint,

P
Rectangle
Rocker shown at left.

and Bezel

,

Cylinder

,

,

Contact your favorite F
or visit our website for more details.

www.foredom.com

Pavé Point
4-48UNF-2A thread

Flat Top Taper
4-48UNF-2A thread (included with H.15,

edom dealer

or

Diamond Tip

A-R15PT

HP10177

H.15D and H.15SJ
handpiece)