Ford Crown 2008 User Manual

Table of Contents

Introduction 4

Instrument Cluster 10

Warning lights and chimes 10
Gauges 15

Entertainment Systems 18

AM/FM stereo 18
AM/FM stereo with CD 20
AM/FM stereo cassette with CD 23
AM/FM stereo with in-dash six CD 28

Climate Controls 34

Manual heating and air conditioning 34
Automatic temperature control 35
Rear window defroster 37

Lights 38

Headlamps 38
Turn signal control 42
Bulb replacement 44

Driver Controls 51

Windshield wiper/washer control 51
Steering wheel adjustment 52
Power windows 63
Mirrors 64
Speed control 66
Moon roof 70
Message center 75

Locks and Security 85

Keys 85
Locks 85
Anti-theft system 93

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

1

Table of Contents

Seating and Safety Restraints 101

Seating 101
Safety restraints 106
Airbags 121
Child restraints 133

Tires, Wheels and Loading 145

Tire information 145
Tire inflation 147
Tire Pressure Monitoring System (TPMS) 160
Vehicle loading 165
Trailer towing 171
Recreational towing 174

Driving 175

Starting 175
Brakes 180
Traction Control™ 183
Air suspension 186
Transmission operation 187

Roadside Emergencies 192

Getting roadside assistance 192
Hazard flasher switch 193
Fuel pump shut-off switch 194
Fuses and relays 195
Changing tires 203
Lug nut torque 210
Jump starting 211
Wrecker towing 216

Customer Assistance 217

Reporting safety defects (U.S. only) 223
Reporting safety defects (Canada only) 224

Cleaning 225

2

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Table of Contents

Maintenance and Specifications 232

Engine compartment 234
Engine oil 236
Battery 239
Engine coolant 241
Fuel information 247
Air filter(s) 263
Part numbers 264
Maintenance product specifications and capacities 266
Engine data 269

Accessories 272

Index 274

All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company. Ford may change the contents without
notice and without incurring obligation.

Copyright © 2007 Ford Motor Company

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

3

Introduction

CALIFORNIA Proposition 65 Warning

WARNING: Engine exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to
the State of California to cause cancer and birth defects or other
reproductive harm. In addition, certain fluids contained in vehicles and
certain products of component wear contain or emit chemicals known
to the State of California to cause cancer and birth defects or other
reproductive harm.

PERCHLORATE MATERIAL

Certain components of this vehicle such as airbag modules, seat belt
pretensioners, and button cell batteries may contain Perchlorate Material
– Special handling may apply for service or vehicle end of life disposal.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

CONGRATULATIONS

Congratulations on acquiring your new Ford. Please take the time to get
well acquainted with your vehicle by reading this handbook. The more
you know and understand about your vehicle, the greater the safety and
pleasure you will derive from driving it.

For more information on Ford Motor Company and its products visit the
following website:

• In the United States: www.ford.com

• In Canada: www.ford.ca

• In Australia: www.ford.com.au

• In Mexico: www.ford.com.mx

Additional owner information is given in separate publications.
This Owner’s Guide describes every option and model variant available

and therefore some of the items covered may not apply to your
particular vehicle. Furthermore, due to printing cycles it may describe
options before they are generally available.

Remember to pass on this Owner’s Guide when reselling the vehicle. It
is an integral part of the vehicle.

Fuel pump shut-off switch: In the event of an accident the

safety switch will automatically cut off the fuel supply to the
engine. The switch can also be activated through sudden vibration (e.g.
collision when parking). To reset the switch, refer to the Fuel pump
shut-off switch in the Roadside Emergencies chapter.

4

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Introduction

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

How can you reduce the risk of personal injury to yourself or others? In
this guide, answers to such questions are contained in comments
highlighted by the warning triangle symbol. These comments should be
read and observed.

Warning symbols on your vehicle

When you see this symbol, it is
imperative that you consult the
relevant section of this guide before
touching or attempting adjustment
of any kind.

Protecting the environment

We must all play our part in
protecting the environment. Correct
vehicle usage and the authorized
disposal of waste, cleaning and
lubrication materials are significant
steps towards this aim. Information in this respect is highlighted in this
guide with the tree symbol.

BREAKING-IN YOUR VEHICLE

Your vehicle does not need an extensive break-in. Try not to drive
continuously at the same speed for the first 1,000 miles (1,600 km) of
new vehicle operation. Vary your speed frequently in order to give the
moving parts a chance to break in.

Drive your new vehicle at least 500 miles (800 km) before towing a
trailer. For more detailed information about towing a trailer, refer to
Trailer towing in the Tires, Wheels and Loading chapter.

Do not add friction modifier compounds or special break-in oils since
these additives may prevent piston ring seating. See Engine oil in the
Maintenance and Specifications chapter for more information on oil
usage.

SPECIAL NOTICES

New Vehicle Limited Warranty

For a detailed description of what is covered and what is not covered by
your vehicle’s New Vehicle Limited Warranty, refer to the Warranty
Guide that is provided to you along with your Owner’s Guide.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

5

Introduction

Notice to owners of Severe Duty vehicles

Before you drive your vehicle, be sure to read the Severe Duty Owner’s
Guide supplement. This book contains important operation and

maintenance information.

Special instructions

For your added safety, your vehicle is fitted with sophisticated electronic
controls.

Please read the section Airbag supplemental restraint system

(SRS) in the Seating and Safety Restraints chapter. Failure to
follow the specific warnings and instructions could result in personal
injury.

Front seat mounted rear-facing child or infant seats should

NEVER be placed in front of an active passenger airbag.

Service Data Recording

Service data recorders in your vehicle are capable of collecting and
storing diagnostic information about your vehicle. This potentially
includes information about the performance or status of various systems
and modules in the vehicle, such as engine, throttle, steering or brake
systems. In order to properly diagnose and service your vehicle, Ford
Motor Company, Ford of Canada, and service and repair facilities may
access vehicle diagnostic information through a direct connection to your
vehicle when diagnosing or servicing your vehicle.

Event Data Recording

Other modules in your vehicle — event data recorders — are capable of
collecting and storing data during a crash or near crash event. The
recorded information may assist in the investigation of such an event.
The modules may record information about both the vehicle and the
occupants, potentially including information such as:

• how various systems in your vehicle were operating;

• whether or not the driver and passenger seatbelts were buckled;

• how far (if at all) the driver was depressing the accelerator and/or the

brake pedal;

• how fast the vehicle was traveling; and

• where the driver was positioning the steering wheel.

6

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Introduction

To access this information, special equipment must be directly connected
to the recording modules. Ford Motor Company and Ford of Canada do
not access event data recorder information without obtaining consent,
unless pursuant to court order or where required by law enforcement,
other government authorities or other third parties acting with lawful
authority. Other parties may seek to access the information
independently of Ford Motor Company and Ford of Canada.

Cell phone use

The use of Mobile Communications Equipment has become increasingly
important in the conduct of business and personal affairs. However,
drivers must not compromise their own or others’ safety when using
such equipment. Mobile Communications can enhance personal safety
and security when appropriately used, particularly in emergency
situations. Safety must be paramount when using mobile communications
equipment to avoid negating these benefits.

Mobile Communication Equipment includes, but is not limited to cellular
phones, pagers, portable email devices, in-vehicle communications
systems, telematics devices and portable two-way radios.

Driving while distracted can result in loss of vehicle control,

accident and injury. Ford strongly recommends that drivers use
extreme caution when using any device that may take their focus off
the road. The drivers primary responsibility is the safe operation of
their vehicle. Only use cell phones and other devices not essential to
the driving task when it is safe to do so.

Export unique (Non–United States/Canada) vehicle specific
information

For your particular global region, your vehicle may be equipped with
features and options that are different from the ones that are described
in this Owner’s Guide. A market unique supplement may be supplied
that complements this book. By referring to the market unique
supplement, if provided, you can properly identify those features,
recommendations and specifications that are unique to your vehicle. This
Owner’s Guide is written primarily for the U.S. and Canadian Markets.
Features or equipment listed as standard may be different on units built
for Export. Refer to this Owner’s Guide for all other required

information and warnings.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

7

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

Fasten Safety Belt Airbag - Front

Airbag - Side

Child Seat Tether
Anchor

Anti-Lock Brake System Parking Brake System

Brake Fluid ­Non-Petroleum Based

Stability Control System Speed Control

Master Lighting Switch Hazard Warning Flasher

Fog Lamps-Front Fuse Compartment

See Owner’s Guide

Child Seat Lower
Anchor

Brake System

Parking Aid System

Fuel Pump Reset Windshield Wash/Wipe

Windshield
Defrost/Demist

8

Rear Window
Defrost/Demist

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Vehicle Symbol Glossary

Introduction

Power Windows
Front/Rear

Child Safety Door
Lock/Unlock

Power Window Lockout

Interior Luggage
Compartment Release

Panic Alarm Engine Oil

Engine Coolant

Engine Coolant
Temperature

Do Not Open When Hot Battery

Avoid Smoking, Flames,
or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering Fluid

Maintain Correct Fluid
Level

Service Engine Soon Engine Air Filter

MAX

MIN

Passenger Compartment
Air Filter

Check Fuel Cap

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Jack

Low Tire Pressure
Warning

9

Instrument Cluster

WARNING LIGHTS AND CHIMES

Standard instrument cluster

Optional instrument cluster

Warning lights and gauges can alert you to a vehicle condition that may
become serious enough to cause expensive repairs. A warning light may
illuminate when a problem exists with one of your vehicle’s functions.
Many lights will illuminate when you start your vehicle to make sure the
bulb works. If any light remains on after starting the vehicle, refer to the
respective system warning light for additional information.

10

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Instrument Cluster

Service Engine Soon: The Service
Engine Soon indicator light

illuminates when the ignition is first
turned to the ON position to check
the bulb and to indicate whether the vehicle is ready for
Inspection/Maintenance (I/M) testing. Normally, the ⬙Service engine soon⬙
light will stay on until the engine is cranked, then turn itself off if no
malfunctions are present. However, if after 15 seconds the ⬙Service
engine soon⬙ light blinks eight times, it means that the vehicle is not
ready for I/M testing. See the Readiness for Inspection/Maintenance
(I/M) testing in the Maintenance and Specifications chapter.

Solid illumination after the engine is started indicates the On Board
Diagnostics System (OBD-II) has detected a malfunction. Refer to On
board diagnostics (OBD-II) in the Maintenance and Specifications
chapter. If the light is blinking, engine misfire is occurring which could
damage your catalytic converter. Drive in a moderate fashion (avoid
heavy acceleration and deceleration) and have your vehicle serviced
immediately by your authorized dealer.

Under engine misfire conditions, excessive exhaust temperatures

could damage the catalytic converter, the fuel system, interior
floor coverings or other vehicle components, possibly causing a fire.

Powertrain malfunction
indicator (if equipped):

Illuminates when a powertrain fault
has been detected. Contact your
authorized dealer as soon as possible.

Check fuel cap (if equipped):

Illuminates when the fuel cap may
not be properly installed. Continued
driving with this light on may cause
the Service engine soon warning
light to come on. Refer to Fuel
filler cap in the Maintenance and Specifications chapter.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

11

Instrument Cluster

Brake system warning light: To
confirm the brake system warning
light is functional, it will
momentarily illuminate when the
ignition is turned to the ON position
when the engine is not running, or in a position between ON and START,
or by applying the parking brake when the ignition is turned to the ON
position. If the brake system warning light does not illuminate at this
time, seek service immediately from your authorized dealer. Illumination
after releasing the parking brake indicates low brake fluid level and the
brake system should be inspected immediately by your authorized dealer.

Driving a vehicle with the brake system warning light on is

dangerous. A significant decrease in braking performance may
occur. It will take you longer to stop the vehicle. Have the vehicle
checked by your authorized dealer. Driving extended distances with
the parking brake engaged can cause brake failure and the risk of
personal injury.

Anti-lock brake system: If the
ABS light stays illuminated or
continues to flash, a malfunction has
been detected, have the system
serviced immediately by your
authorized dealer. Normal braking is still functional unless the brake
warning light also is illuminated.

Airbag readiness: If this light fails
to illuminate when the ignition is
turned to ON, continues to flash or
remains on, have the system
serviced immediately by your authorized dealer. A chime will also sound
when a malfunction in the supplemental restraint system has been
detected.

Safety belt: Reminds you to fasten
your safety belt. A Belt-Minder威
chime will also sound to remind you
to fasten your safety belt. Refer to
the Seating and safety restraints
chapter to activate/deactivate the Belt-Minder威 chime feature.

BRAKE

P!

ABS

12

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Instrument Cluster

Charging system: Illuminates when
the battery is not charging properly.

Engine oil pressure: Illuminates
when the oil pressure falls below the
normal range. Check the oil level
and add oil if needed. Refer to
Engine oil in the Maintenance and Specifications chapter.

Engine coolant temperature
(if equipped): Illuminates when

the engine coolant temperature is
high. Stop the vehicle as soon as possible, switch off the engine and let
cool. Refer to Engine coolant in the Maintenance and Specifications
chapter.

Never remove the coolant reservoir cap while the engine is

running or hot.

Traction control™ AdvanceTrac威
active (if equipped): Illuminates

when the Traction control™ system
is active. It will be lit for a minimum
of four seconds or for the duration
of the Traction Control™ event,
refer to the Driving chapter for more information.

Severity indicator (if equipped):

Displays the indicated severity color
when any of the following warning
conditions has occurred:

• Red: Low Oil Pressure, Charge
System, Engine Coolant Over Temperature, Door Ajar

• Amber: Low Fuel

Refer to Message Center in the Driver Controls chapter.

Low tire pressure warning
(if equipped): Illuminates when

your tire pressure is low. If the light
remains ON at start up or while
driving, the tire pressure should be
checked. Refer to Inflating Your Tires in the Tires, Wheels and

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

13

Instrument Cluster

Loading chapter. When the ignition is first turned to ON, the light will
illuminate for 3 seconds to ensure the bulb is working. If the light does
not turn ON, have the system inspected by your authorized dealer. For
more information on this system, refer to Tire Pressure Monitoring
System in the Tires, Wheels and Loading chapter.

Air suspension (if equipped):

Illuminates when the air suspension
is turned OFF, the load limit is
exceeded or the air suspension
system requires servicing.

Low fuel (if equipped):

Illuminates when the fuel level in
the fuel tank is at or near empty
(refer to Fuel gauge in this chapter
for more information).

O/D off: Illuminates when the
overdrive function of the
transmission has been turned OFF,
refer to the Driving chapter. If the
light does not illuminate, have the transmission serviced soon, or damage
may occur.

Speed control (if equipped):

Illuminates when the speed control
is activated. Turns off when the
speed control system is deactivated.

O/D

OFF

Door ajar (if equipped):

Illuminates when one of the doors is
not completely shut and the ignition
is turned to ON. With the ignition in
RUN position, a tone will sound for one second (if a door is open).

Turn signal: Illuminates when the
left or right turn signal or the
hazard lights are turned on. If the
indicators stay on or flash faster, check for a burned out bulb.

14

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Instrument Cluster

High beams: Illuminates when the
high beam headlamps are turned on.

Headlamps on warning chime: Sounds when the headlamps or parking
lamps are on, the ignition is off (the key is not in the ignition) and the
driver’s door is opened.

Key-in-ignition warning chime: Sounds when the key is left in the
ignition in the OFF/LOCK or ACCESSORY position and the driver’s door
is opened.

GAUGES

Speedometer: Indicates the
current vehicle speed.

Engine coolant temperature
gauge: Indicates engine coolant

temperature. At normal operating
temperature, the needle will be in
the normal range (between “H” and
“C”). If it enters the red section,

the engine is overheating. Stop
the vehicle as soon as safely
possible, switch off the engine and let the engine cool.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

15

Instrument Cluster

Never remove the coolant reservoir cap while the engine is
running or hot.

Odometer: Registers the total miles (kilometers) of the vehicle.

• Without Message Center

To switch the display from Metric to
English, press and hold the button
on the cluster for three seconds.

• With Message Center

Refer to Message Center in the
Driver Controls chapter on how to
switch the display from Metric to
English and the odometer to the
speedometer.

Trip odometer: Registers the miles (kilometers) of individual journeys.

• Without Message Center

Press and release the button on the
cluster to toggle between odometer
and trip odometer display. To reset,
press the button again until the trip
reading is 000000.0 miles.

• With Message Center

Press and release the message
center INFO button until “TRIP”
appears in the display (this
represents the trip mode). Press the
control again to select Trip A and
Trip B features. Press and hold the
RESET button for two seconds to
reset.

16

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Instrument Cluster

Tachometer: Indicates the engine
speed in revolutions per minute.
Driving with your tachometer
pointer continuously at the top of
the scale may damage the engine.

Fuel gauge: Indicates
approximately how much fuel is left
in the fuel tank (when the ignition
is in the ON position). The fuel
gauge may vary slightly when the
vehicle is in motion or on a grade.

The arrow near the fuel pump icon
indicates which side of the vehicle
the fuel filler door is located.

Refer to Filling the tank in the Maintenance and Specifications
chapter for more information.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

17

Entertainment Systems

AUDIO SYSTEMS

AM/FM stereo (if equipped)

VOL

PUSH

ON

6

TONE

CLK

7

5

1 2 3 4 AM/FM

4

1. Seek: Press

next strong station down/up the
frequency band.

2. Tune: Press

change radio frequency down/up.

/ to find the

/ to manually

TONE VOL

ST DX

1

FM

12

SEEK

TUNE

2

3

3. AM/FM: Press to choose a

frequency band in radio mode.

4. Memory preset buttons: To set

a station: Select frequency band
AM/FM; tune to a station, press and
hold a preset button until sound returns.

18

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

AM/FM

1 2 3 4

Entertainment Systems

5. Power/volume: Press to turn

ON/OFF; turn to increase or
decrease volume levels.

6. Tone: Press TONE until the

desired level — Bass, Treble, Fade
appears on the display. Turn the
volume control to raise/lower the
levels, or to move the audio sound
from the right to left or the front to
back (if equipped).

7. CLK (Clock): To set the hour,

press and hold CLK until CLOCK
SET appears in the display.
Continue to hold CLK as you press
SEEK to decrease

increase

To set the minute, press and hold CLK until CLOCK set appears in the
display. Continue to hold CLK as you press TUNE to decrease

increase

the hours.

the minutes.

or

TONE

CLK

or

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

19

Entertainment Systems

AM/FM Stereo Single CD Premium audio system (if equipped)

1. CD slot: Insert a CD, label side

up. With the ignition on, the radio
will begin play when a CD is
inserted. If the ignition is off, press CD prior to inserting a disc. Do not
force a disc into the system as damage could result.

2. SEEK: Press to access the next

) or previous ( ) radio

(
station or CD track. Press and hold

to advance/reverse in the current CD track.

3. TUNE: Press to manually go up

) or down ( ) the radio

(
frequency.

4. MUTE: Press to mute the playing

media. Press again to return to the
playing media or turn the volume
control to adjust the volume.

20

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

5. Eject: Press to eject the CD. If

the disc is not removed within the
allotted time, the system will
automatically reload the CD and begin play. Note: The eject function will
work when the ignition is turned off.

6. BASS: Press BASS; then

press

SEL to

decrease/increase the level of bass
output.

TREB (Treble): Press TREB; then
press

SEL to

decrease/increase the level of treble
output.

7. BAL (Balance): Press BAL; then

press

SEL to shift sound to

the left/right speakers.

BASS

TREB

BAL

FADE

SEL

+

SEL

+

FADE: Press FADE; then press

SEL to shift sound to the

rear/front speakers.

8. SEL: Use with Bass, Treble,

Balance, Fade and other menu
functions.

9. MENU: Press MENU to access

the following functions:

Compression: Brings soft and loud CD passages together for a more
consistent listening level when in CD mode. Press MENU until

compression status is displayed. Press

SEL to enable the

compression feature when COMPRESS OFF is displayed. Press SEL
again to disable the feature when COMPRESS ON is displayed. When
activated, the compression icon will appear in the display.

Autoset: Allows you to set the strongest local radio stations without
losing your original manually set preset stations for AM/FM1/FM2. Press

MENU until AUTOSET appears in the display. Press

SEL to

toggle ON/OFF. When the six strongest stations are filled, the station
stored in preset 1 will begin playing. If there are less than six strong
stations, the system will store the last one in the remaining presets.

21

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

When activated, AUTOSET will momentarily appear in the display when
any of the preset controls are pressed.

Speed sensitive volume: Radio volume changes automatically and
slightly with vehicle speed to compensate for road and wind noise.
Recommended level is 1–3. Level 0 turns the feature off and level 7 is
the maximum setting.

Press MENU to access and use
The level will appear in the display.

Setting the clock: Press MENU until SELECT HOUR or SELECT MINS
is displayed. Press
hours/minutes. Press MENU again to disengage clock mode.

Note: The menu selections will remain in the display for approximately
10 seconds, at which time the display will return to the previous mode.
You may also exit the menu options by pressing any other audio control.

10. Memory presets: To set a

station: Select frequency band, tune
to a station, press and hold a preset
button until sound returns.

11. On/Off/Volume: Push to turn

on/off; turn to adjust the volume
levels.
Note: With the ignition turned off,
you may press the volume control to
momentarily view the clock.

12. CD: Press to enter CD mode if a CD is already present in the system.

In radio mode, the CD icon will appear in the display if a CD is loaded
into the system.

13. AM: Press to select the AM

frequency.

SEL to manually decrease/increase the

SEL to adjust the volume setting.

14. FM: Press to select the FM

frequency. Press repeatedly to
toggle between FM1 and FM2.

15. SHUF (Shuffle): Press to play

all tracks on the current CD in
random order. Press again to stop.

22

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

16. SCAN: Press SCAN to hear a

brief sampling of radio stations or
CD tracks. Press again to stop.

Premium/Audiophile Satellite Compatible AM/FM Stereo Single
CD/Cassette system (if equipped)

1. CD slot: Insert a CD, label side

up. With the ignition on, the radio
will begin to play a CD once
inserted. With the ignition off, the CD control must be pressed before
inserting the disc. Failure may result in damage to the CD and/or audio
system.

2. CD eject: Press to eject a CD. If

the disc is not removed within the
allotted time, the system will
automatically reload the CD and begin play. Note: The eject function will
work when the ignition is turned off.

23

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

3. BASS: Press BASS; then

press

SEL-TEXT to

decrease/increase the level of bass

BASS

TREB

SEL-TEXT

+

output.

TREB (Treble): Press TREB; then
press

SEL-TEXT to

decrease/increase the level of treble

BASS

TREB

SEL-TEXT

+

output.

4. BAL (Balance): Press BAL; then

press

SEL-TEXT to shift

sound to the left/right speakers.

FADE: Press FADE; then
press

SEL-TEXT to shift

sound to the rear/front speakers.

BAL

FADE

BAL

FADE

SEL-TEXT

+

SEL-TEXT

+

5. Phone/mute: Press to mute the

playing media. Press again to return
to the playing media or turn the
volume control to adjust the volume.

6. SEL/TEXT: Use with Bass,

Treble, Balance, Fade and other
menu functions.

TEXT: TEXT is only available when equipped with Satellite radio. Your
Audiophile radio may be equipped with Satellite ready capability. The kit
to enable Satellite reception is available through your dealer. Detailed
Satellite instructions are included with the dealer installed kit. Check

with your authorized dealer for availability.

7. MENU: Press MENU repeatedly

to access RDS on/off. Press

SEL-TEXT to toggle RDS

on/off. Press MENU again to access Program type mode or Show
Type/Name mode. (MENU must be pressed within 10 seconds to proceed
to the next RDS mode.)

The Federal Communications Commission (FCC) and the Canadian Radio
and Telecommunications Commission (CRTC) recommend that FM radio
broadcasters use RDS technology to transmit information. FM radio

24

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

stations are independently operated and individually elect to use RDS
technology to transmit station ID and program type as desired.

FIND Program type: Allows you to search RDS-equipped stations for a
certain category of music format: Classic, Country, Info, Jazz, Oldies,
R&B, Religious, Rock, Soft, Top 40.
With RDS ON, press MENU until the program type menu is displayed.

One of the various program types will appear. Press
to scroll through music types. Press SEEK or SCAN to search for a

station playing the requested music category.
Show TYPE: Selects between displaying the station’s call letters or

music format when RDS is enabled. Press and hold MENU until SHOW
XX appears in the display. Press
TYPE.

Compression: Brings soft and loud CD passages together for a more
consistent listening level when in CD mode. Press MENU repeatedly until

compression status is displayed. Press
enable the compression feature when COMPRESS OFF is displayed.
Press
COMPRESS ON is displayed. When activated, the compression icon will

appear in the display.
Occupancy mode (Available only on Audiophile audios): Press MENU

repeatedly until occupancy mode appears in the display.
Press
occupancy mode.

Autoset: Allows you to set the strongest local radio stations without
losing your original manually set preset stations for AM/FM1/FM2. Press
MENU repeatedly until AUTOSET appears in the display.

Press
stations are filled, the station stored in preset 1 will begin playing. If

there are less than six strong stations, the system will store the last one
in the remaining presets. When activated, AUTOSET will momentarily
appear in the display when any of the preset controls are pressed.

Speed sensitive volume: Radio volume changes automatically and
slightly with vehicle speed to compensate for road and wind noise.
Recommended level is 1–3. Level 0 turns the feature off and level 7 is
the maximum setting.

Press MENU repeatedly to access and use
the volume setting. The level will appear in the display.

SEL-TEXT control again to disable the feature when

SEL-TEXT to select ALL, DRIVER or REAR SEAT

SEL-TEXT to toggle ON/OFF. When the six strongest

SEL-TEXT to select NAME or

SEL-TEXT control to

SEL/TEXT to adjust

SEL-TEXT

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

25

Entertainment Systems

Dolby: Works in tape mode to reduces tape noise and hiss. Press MENU
until DOLBY XX appears in the display. Press
toggle ON/OFF.

The Dolby威 noise reduction system is manufactured under license from
Dolby Laboratories Licensing Corporation. Dolby威 and the double-D
symbol are registered trademarks of Dolby Laboratories Licensing
Corporation.

Setting the clock: Press MENU repeatedly until SELECT HOUR or
SELECT MINS is displayed. Press

SEL-TEXT to manually

decrease/increase the hours/minutes. Press MENU again to disengage
clock mode.

Note: The menu selections will remain in the display for approximately
10 seconds, at which time the display will return to the previous mode.
You may also exit the menu options by pressing any other audio control.

8. Cassette: Insert a cassette facing to the right.

9. TUNE: Press to manually go up

or down the radio frequency.

CAT: CAT is only available when equipped with Satellite Radio. Your
system may be equipped with Satellite ready capability. The kit to enable
Satellite reception is available through your dealer. Detailed Satellite
instructions are included with the dealer installed kit.

Check with your authorized dealer for availability.

10. Side 1–2: Press to access the

next side of the cassette tape. The
display will indicate whether TAPE
1 or TAPE 2 is playing.

11. SEEK: Press to access the

next/previous radio station, tape
selection or CD track.

12. REW (Rewind): Press to

rewind in tape or CD mode.

SEL-TEXT to

FF

REW

34

FF (Fast forward): Press to fast
forward in tape or CD mode.

26

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

13. SCAN: Press SCAN to hear a

brief sampling of radio stations,
selections or CD tracks. Press again
to stop.

14. SHUF (Shuffle): Press to play

the tracks on the current CD in
random order. Press again to stop.

15. Memory presets: To set a

station: Select frequency band, tune
to a station, press and hold a preset
button until sound returns.

16. AM/FM: Press to toggle

between AM/FM1/FM2 modes.

17. Tape eject: Press to eject the

tape.

18. CD/TAPE: Press to toggle

between CD and TAPE mode. In
radio and tape mode, the CD icon
will appear in the display if a CD is loaded into the system.

19. SAT: Your system may be

equipped with Satellite Ready
capability. The kit to enable the
Satellite reception is available through your dealer. Detailed satellite
instructions are included with the dealer installed kit.

Check with your authorized dealer for availability.

20. On/Off/Volume: Push to turn

on/off; turn to adjust the volume
levels. Note: With the ignition
turned off, you may press the
volume control to momentarily view
the clock.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

27

Entertainment Systems

Audiophile AM/FM Satellite Compatible Stereo In-dash Six CD
sound system (if equipped)

1. CD slot: To insert a CD, press

LOAD. When the system is ready,
insert a CD, label side up.

2. SEEK: Press to access the

next/previous radio station or CD
track. Press and hold to
advance/reverse in the current CD track.

3. TUNE/CAT: Press to manually go

up or down the radio frequency.
TEXT is only available when

equipped with Satellite radio. Your system may be equipped with
Satellite ready capability. The kit to enable Satellite reception is available
through your dealer. Detailed Satellite instructions are included with the
dealer installed kit. Check with your authorized dealer for

availability.

28

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

4. MUTE: Press to mute the playing

media. Press again to return to the
playing media or turn the volume
control to adjust the volume.

5. Eject: Press to eject CD(s) when

the ignition is on or off. Numbers
will illuminate in the display
indicating which CD slots are loaded with CDs. To eject a specific CD,
press eject and the corresponding preset number. If no preset is
selected, the system will eject the currently selected CD. Press and hold
to eject all loaded discs.

Note: If the CD is not removed within 15 seconds, the system will reload
the disc and begin play if the system is on.

6. BASS: Press BASS; then

press

SEL-TEXT to

decrease/increase the level of bass
output.

TREB (Treble): Press TREB; then
press

SEL-TEXT to

decrease/increase the level of treble
output.

7. BAL (Balance): Press BAL; then

press

SEL-TEXT to shift

sound to the left/right speakers.

BASS

TREB

BASS

TREB

BAL

FADE

SEL-TEXT

+

SEL-TEXT

+

SEL-TEXT

+

FADE: Press FADE; then press

SEL-TEXT to shift sound to

the rear/front speakers.

BAL

FADE

SEL-TEXT

+

8. SEL-TEXT: Use with Bass,

Treble, Balance, Fade and other
menu functions.

TEXT: TEXT is only available when equipped with Satellite radio. Your
system may be equipped with Satellite ready capability. The kit to enable
Satellite reception is available through your dealer. Detailed Satellite
instructions are included with the dealer installed kit. Check with your

authorized dealer for availability.

29

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

9. MENU: Press MENU repeatedly

to access RDS on/off.
Use
RDS on/off. Press MENU again to access Program type mode or Show

Type mode. (MENU must be pressed within 10 seconds to proceed to
the next RDS mode.)

The Federal Communications Commission (FCC) and the Canadian Radio
and Telecommunications Commission (CRTC) recommend that FM radio
broadcasters use RDS technology to transmit information. FM radio
stations are independently operated and individually elect to use RDS
technology to transmit station ID and program type as desired.

FIND Program type: Allows you to search RDS-equipped stations for a
certain category of music format: Classic, Country, Info, Jazz, Oldies,
R&B, Religious, Rock, Soft, Top 40.
With RDS ON, press MENU until the program type menu is displayed.

One of the various program types will appear. Press
to scroll through music types. Press SEEK or SCAN to search for a

station playing the requested music category.
Show TYPE: Selects between displaying the station’s call letters or

music format when RDS is enabled. Press MENU until SHOW XX appears
in the display. Press to select NAME or TYPE.

Compression: Brings soft and loud CD passages together for a more
consistent listening level when in CD mode. Press MENU until

compression status is displayed. Press
compression feature when COMPRESS OFF is displayed. Press the SEL

control again to disable the feature when COMPRESS ON is displayed.
When activated, the compression icon will illuminate in the display.

Occupancy mode (Available on Audiophile audios only): Press MENU
until occupancy mode appears in the display. Press
select ALL, DRIVER or REAR SEAT occupancy mode.

Autoset: Allows you to set the strongest local radio stations without
losing your original manually set preset stations for AM/FM1/FM2. Press

MENU until AUTOSET appears in the display. Press
to toggle ON/OFF. When the six strongest stations are filled, the station

stored in preset 1 will begin playing. If there are less than six strong
stations, the system will store the last one in the remaining presets.
When activated, AUTOSET will appear in the display when any of the
preset controls are pressed.

SEL-TEXT to toggle

SEL-TEXT

SEL-TEXT to enable the

SEL-TEXT to

SEL-TEXT

30

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

Speed sensitive volume: Radio volume changes automatically and
slightly with vehicle speed to compensate for road and wind noise.
Recommended level is 1–3. Level 0 turns the feature off and level 7 is
the maximum setting.

Press MENU to access and use
setting. The level will appear in the display.

Setting the clock: Press MENU until SELECT HOUR or SELECT MINS
is displayed. Press
hours/minutes. Press MENU again to disengage clock mode.

10. Memory presets: To set a

station: Select frequency band, tune
to a station, press and hold a preset
button until sound returns. In CD mode, press to select a specific CD to
play.

11. On/Off/Volume: Push to turn

on/off; turn to adjust the volume
levels.

Note: With the ignition off, you may
press the volume control to
momentarily view the clock.

12. LOAD: Press to load a CD.

Press LOAD and a specific preset to
load in that particular slot. Available
slots are indicated by small flashing indicators in the display. When the
system is ready to accept a disc, LOAD CD X will appear in the display.
Load the CD. Press and hold to autoload up to 6 discs.

Note: Ensure that the system is ready to accept the CD. Do not force
the disc into the CD slot as damage could result.

13. AM/FM: Press repeatedly to

toggle between AM/FM1/FM2 mode.

SEL-TEXT to increase/decrease the

SEL-TEXT to adjust the volume

14. CD: Press to enter CD mode.

Press CD and a preset to select a
specific CD to play.

15. SAT: Your system may be equipped with Satellite Ready capability.

The kit to enable the Satellite reception is available through your
authorized dealer. Detailed satellite instructions are included with the
dealer installed kit.

Check with your authorized dealer for availability.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

31

Entertainment Systems

16. SHUF (Shuffle) /SCAN: Press SCAN to hear a brief sampling of

radio stations or CD tracks on the current CD. Press again to stop.
SHUF (Shuffle): Press and hold to play the CD tracks in random order

for the CD currently being played. Press again to stop.

GENERAL AUDIO INFORMATION

Radio frequencies: AM and FM frequencies are established by the
Federal Communications Commission (FCC) and the Canadian Radio and
Telecommunications Commission (CRTC). Those frequencies are:

AM - 530, 540–1700, 1710 kHz
FM- 87.7, 87.9–107.7, 107.9 MHz
Radio reception factors: There are three factors that can affect radio

reception:

• Distance/strength: The further you travel from a station, the weaker
the signal and the weaker the reception.

• Terrain: Hills, mountains, tall buildings, power lines, electric fences,
traffic lights and thunderstorms can interfere with your reception.

• Station overload: When you pass a broadcast tower, a stronger signal
may overtake a weaker one and play while the weak station frequency
is displayed.

Cassette/player care:

Do:

• Use only cassettes that are 90 minutes long or less.

• Tighten very loose tapes by inserting a finger or pencil into the hole

and turning the hub.

• Remove loose labels before inserting tapes.

• Allow tapes which have been subjected to extreme heat, humidity or

cold to reach a moderate temperature before playing.

• Clean the cassette player head with a cassette cleaning cartridge after
10–12 hours of play to maintain good sound/operation.

Don’t:

• Expose tapes to direct sunlight, extreme humidity, heat or cold.

• Leave tapes in the cassette player for a long time when not being

played.

32

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Entertainment Systems

CD/CD player care:

Do:

• Handle discs by their edges only. Never touch the playing surface.

• Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

Don’t:

• Expose discs to direct sunlight or heat sources for extended periods
of time.

• Clean using a circular motion.

CD units are designed to play commercially pressed 4.75 in (12
cm) audio compact discs only. Due to technical incompatibility,
certain recordable and re-recordable compact discs may not
function correctly when used in Ford CD players. Dirty, warped
or damaged CDs, irregular shaped CDs, CDs with a scratch
protection film attached, and CDs with homemade paper
(adhesive) labels should not be inserted into the CD player. The
label may peel and cause the CD to become jammed. It is
recommended that homemade CDs be identified with permanent
felt tip marker rather than adhesive labels. Ballpoint pens may
damage CDs. Please contact your authorized dealer for further
information.

Audio system warranty and service: Refer to the Warranty Guide

for audio system warranty information. If service is necessary, see your
dealer or qualified technician.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

33

Climate Controls

MANUAL HEATING AND AIR CONDITIONING SYSTEM
(IF EQUIPPED)

1. Fan speed adjustment: Controls

the volume of air circulated in the
vehicle.

2. Temperature selection:

Controls the temperature of the
airflow in the vehicle.

3. Air flow selections: Controls the direction of the airflow in the

vehicle. See the following for a brief description on each control.
MAX A/C: Uses recirculated air to cool the vehicle. Air flows from the

instrument panel vents only. This mode will help prevent unpleasant
odors from entering the vehicle.

NORM A/C: Uses outside air to cool the vehicle. Air flows from the
instrument panel vents only.

VENT: Distributes outside air through the instrument panel vents.
OFF: Outside air is shut out and the fan will not operate.
FLOOR: Distributes outside air through the floor vents.
MIX: Distributes outside air through the windshield defroster vents, floor

vents and side window demisters.

: Distributes outside air through the windshield defroster vents and

the side window demisters.

1 2 3

LO

HI

NORM

A/C

MAX

A/C

VENT

OFF

FLOO

R

MIX

Operating tips

• To reduce fog build up on the windshield during humid weather, place
the air flow selector in the

position.

• To reduce humidity build up inside the vehicle: do not drive with the
air flow selector in the OFF or MAX A/C position.

• Under normal weather conditions, do not leave the air flow selector in
MAX A/C or OFF when the vehicle is parked. This allows the vehicle
to “breathe” using the outside air inlet vents.

• Do not put objects under the front seats that will interfere with the
airflow to the back seats.

• Remove any snow, ice or leaves from the air intake area at the base of
the windshield.

34

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Climate Controls

To aid in side window defogging/demisting in cold weather:

1. Select NORM A/C.

2. Adjust the temperature control to maintain comfort.

3. Set the fan speed to HI.

4. Direct the outer instrument panel vents towards the side windows.

To increase airflow to the outer instrument panel vents, close the vents
located in the middle of the instrument panel.

Do not place objects on top of the instrument panel as these
objects may become projectiles in a collision or sudden stop.

ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC)
SYSTEM (IF EQUIPPED)

11 1 2 310

F

OUTSIDE TEMP AUTOMATIC

MAX A/C

NORM A/C

VENT FLOOR FLR • DEF DEF

AUTO

OFF

HI

LO

9 8 7 6 5 4

1. OFF: Outside air is shut out and

the fan will not operate.

2. AUTOMATIC: Press

AUTOMATIC and select the desired
temperature using the temperature
controls. The system will automatically determine fan speed, airflow
location, and outside or recirculated air to heat or cool the vehicle to the
selected temperature. The fan speed will remain automatic unless the
thumbwheel is turned all the way to LO.

35

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Climate Controls

3. Fan speed: Turn to manually

increase or decrease fan speed.

4. Defrost:

vents and the side window demisters.

5. Floor/defrost: Distributes outside air through the windshield

defroster vents, floor vents and the side window demisters.

6. Floor: Distributes outside air through the floor vents.

7. Vent: Distributes outside air through the instrument panel vents.

8. Norm A/C: Uses outside air to cool the vehicle . Air flows from the

instrument panel vents only.

9. Max A/C: Uses recirculated air to cool the vehicle. Air flows from the

instrument panel vents only. This mode will help prevent unpleasant
odors from entering the vehicle.

10. Outside Temp: Press to display

the outside temperature. It will
remain in the display until pressed
again. The temperature will be most accurate when the vehicle is in
motion.

11. Temperature control: Press this control to select the temperature.

The display window indicates the selected temperature.
Fahrenheit/Celsius temperature: Press MAX A/C and DEF

simultaneously to toggle between Fahrenheit and Celsius temperature.
The set point temperatures in Celsius will be displayed in half-degree
increments.

Operating tips

• To reduce fog build up on the windshield during humid weather, place
the air flow selector in the

• To reduce humidity build up inside the vehicle: do not drive with the
air flow selector in the OFF or MAX A/C position.

• Under normal weather conditions, do not leave the air flow selector in
MAX A/C or OFF when the vehicle is parked. This allows the vehicle
to “breathe” using the outside air inlet vents.

• Do not put objects under the front seats that will interfere with the
airflow to the back seats.

Distributes outside air through the windshield defroster

position.

36

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Climate Controls

• Remove any snow, ice or leaves from the air intake area at the base of
the windshield.

To aid in side window defogging/demisting in cold weather:

1. Select NORM A/C.

2. Adjust the temperature control to maintain comfort.

3. Set the fan speed to HI.

4. Direct the outer instrument panel vents towards the side windows.

To increase airflow to the outer instrument panel vents, close the vents
located in the middle of the instrument panel.

Do not place objects on top of the instrument panel as these
objects may become projectiles in a collision or sudden stop.

REAR WINDOW DEFROSTER

The rear defroster control is located
on the instrument panel.

Press the rear defroster control to
clear the rear window of thin ice
and fog. A small LED will illuminate
when the rear defroster is activated.

The ignition must be in the ON position to operate the rear window
defroster.

The defroster turns off automatically after a predetermined amount of
time or when the ignition is turned to the OFF position. To manually
turn off the defroster, press the control again.

Activating the rear window defroster will also activate the heated mirrors
(if equipped). For more information refer to Heated outside mirrors in
the Driver Controls chapter.

Do not use razor blades or other sharp objects to clean the inside
of the rear window or to remove decals from the inside of the
rear window. This may cause damage to the heated grid lines and
will not be covered by your warranty.

37

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Lights

HEADLAMP CONTROL

Turns the lamps off.

Turns on the parking
lamps, instrument panel lamps,
license plate lamps and tail lamps.

Turns the headlamps on.

Autolamp control

The autolamp system provides light
sensitive automatic on-off control of
the exterior lights normally
controlled by the headlamp control.

The autolamp system also keeps the
lights on for a predetermined period
of time after the ignition switch is
turned to OFF. The delay period can
be adjusted up to a maximum of
approximately 3 minutes in
duration.

• To turn autolamps on, rotate the control counterclockwise to the next

position from OFF.

• To turn autolamps off, rotate the control clockwise

The headlamps will also turn on when the wipers are turned on.
To change the duration of the autolamp delay, carry out the following

sequence:
Note: Steps 2 through 5 must be carried out within a 10 second period.

1. Start with the ignition switch in the OFF position and the headlamp
switch in the AUTOLAMP position.

2. Place the headlamp switch in the OFF position.

3. Place the ignition switch in the RUN position and then back to OFF.

4. Place the headlamp switch in the AUTOLAMP position.

• At this point, the exterior lamps turn on.

38

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Lights

5. At the desired autolamp time delay, place the headlamp switch in the
OFF position.

• At this point, the exterior lamps turn off and the time delay is set.

High beams

Push the lever toward the
instrument panel to activate. Pull
the lever towards you to deactivate.

Flash to pass

Pull toward you slightly to activate
and release to deactivate.

Daytime running lamps (DRL) (if equipped)

Turns the headlamps on with a reduced output. To activate:

• the key must be in the ON position,

• the headlamp control is in the OFF or Parking lamps position.

• the vehicle is not in Park

Always remember to turn on your headlamps at dusk or during

inclement weather. The Daytime Running Light (DRL) System
does not activate your tail lamps and generally may not provide
adequate lighting during these conditions. Failure to activate your
headlamps under these conditions may result in a collision.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

39

Lights

PANEL DIMMER CONTROL

Use to adjust the brightness of the
instrument panel during headlamp
and parklamp operation.

• Rotate the thumbwheel from left
to right to brighten the
instrument panel.

• Rotate the thumbwheel from right
to left to dim the instrument
panel.

Domelamp Control

The panel dimmer control also controls the domelamp operation.

• Rotate the thumbwheel fully to the right, past detent to activate the
domelamp.

• In order to turn off the domelamp, rotate the thumbwheel to the left.

AIMING THE HEADLAMPS

The headlamps on your vehicle are properly aimed at the assembly plant.
If your vehicle has been in an accident the alignment of your headlamps
should be checked by your authorized dealer.

Headlamp aim adjustment

The headlamps are designed to be mechanically aimed, but can also be
aimed visually by doing the following:

1. Park the vehicle directly in front of a wall or screen on a level surface,

approximately 25 feet (7.6 meters) away. Check your headlamp
alignment at night or in a dark area so that you can see the headlamp
beam pattern.

40

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Lights

• (1) 8 feet (2.4 meters)

• (2) Center height of lamp to

ground

• (3) 25 feet (7.6 meters)

• (4) Horizontal reference line

• (5) Center of headlamps

• (6) Center line of the vehicle

2. The center of the headlamp is

marked either on the lens (a circle
or cross marker) or on the bulb shield, internal to the lamp (mark or
feature). Measure the height from the center of your headlamp to the
ground (2) and mark an 8 foot (2.4 meter) long horizontal line on the
wall or screen (1) at this height (masking tape works well).

3. Turn on the low beam headlamps

and open the hood.

4. Locate the high intensity area of

the beam pattern and place the top
edge of the intensity zone even with
the horizontal reference line (4). If
the top edge of the high intensity
area is not even with the horizontal
line, follow the next step to adjust
it.

5. Locate the vertical adjuster for

each headlamp. Adjust the aim by
turning the adjuster control either
clockwise (to adjust down) or
counterclockwise (to adjust up).

6. In addition to the horizontal line

marked in step 2, a pair of vertical
lines (5) must be marked at the
center line of the headlamps on the
wall or screen.

7. On the wall or screen, locate the

high intensity area of the beam pattern. The left edge of the high
intensity area should be even with the vertical line corresponding to the
headlamp under adjustment. If the left edge of the high intensity area is
not even with the vertical line, follow the next step to adjust it.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

41

Lights

8. Locate the horizontal adjuster for

each headlamp. Turn it clockwise or
counterclockwise, to place the left
edge of the high intensity area even
with the vertical line corresponding
to the headlamp under adjustment.

TURN SIGNAL CONTROL

• Push down to activate the left
turn signal.

• Push up to activate the right turn
signal.

The flash rate of the turn signal will speed up considerably if the left or
right turn lamp bulb (front or rear) is burned out.

INTERIOR LAMPS

Map/Courtesy lamps

The courtesy lamps light when:

• any door is opened.

• the instrument panel dimmer

switch is rotated past the detent.

• the UNLOCK control of the
remote entry controls is pressed
and the ignition is OFF.

The reading lamps can be turned on
by pressing the rocker controls next
to each lamp.

If equipped with Remote Keyless Entry, the courtesy lamp will illuminate
whenever any door is opened and will remain on for 25 seconds after the
door is shut or when the ignition is turned to the ON position.

42

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

With overhead console

With overhead console and moon
roof

To turn on the map lamps, press the
map lamp control.

Rear courtesy/reading lamps

Rotate the lens to illuminate the
lamp. With the lens in the flat
position, the courtesy lamp lights
when:

• Any door is opened.

• The panel dimmer thumbwheel is

rotated fully to the right past
detent.

Lights

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

43

Lights

BULB REPLACEMENT

Headlamp Condensation

The headlamps are vented to equalize pressure. When moist air enters
the headlamp(s) through the vents, there is a possibility that
condensation can occur. This condensation is normal and will clear
within 45 minutes of headlamp operation.

Using the right bulbs

Replacement bulbs are specified in the chart below. Headlamp bulbs
must be marked with an authorized “D.O.T.” for North America and an
“E” for Europe to ensure lamp performance, light brightness and pattern
and safe visibility. The correct bulbs will not damage the lamp assembly
or void the lamp assembly warranty and will provide quality bulb burn
time.

Function Trade Number

Headlamp 9007
Park lamp and turn lamp (front) 3457 AK (amber)
Side marker (front) 194 AK (amber)
Tail, stop, turn (rear) 3157K
Side marker (rear) 194
Backup lamp 3156K
License plate lamp 168
High-mount brakelamp 912
Luggage compartment lamp 212-2
Rear reading lamp 578
Map lamp 906
Dual floorwell lamp 906
Glove compartment 168
Visor vanity lamp - Slide on Rail system

(SOR)
All replacement bulbs are clear in color except where noted.
To replace all instrument panel lights - see your authorized dealer.

37

Replacing the interior bulbs

Check the operation of all bulbs frequently.

44

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Lights

Overhead console lamps

To remove and replace the lamps in the overhead console:

1. Make sure the headlamp switch is

in the OFF position and remove the
overhead console from the headliner
by pulling it straight down.

2. Remove the bulb socket from the

back of the lamp housing by pulling
it straight out.

3. Remove the bulb from the socket

by pulling straight out.

Install the new bulb in reverse order.

Replacing exterior bulbs

Check the operation of all the bulbs frequently.

Replacing headlamp bulbs

To remove the headlamp bulb:

1. Make sure headlamp switch is in OFF position, then open the hood.

2. Remove the radiator cover by turning the three knobs to the unlock

position.

3. Remove two retainers and pull

headlamp assembly forward to
expose bulb.

4. Disconnect the electrical

connector from the bulb by pulling
rearward.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

45

Lights

5. Remove the bulb retaining ring by

rotating it counterclockwise (when
viewed from the rear) to free it
from the bulb socket, and slide the
ring off the plastic base. Keep the
ring to retain the new bulb.

6. Without turning, remove the old

bulb from the lamp assembly by
gently pulling it straight back out of
the lamp assembly.

To install the new bulb:

Handle a halogen headlamp bulb carefully and keep out of

children’s reach. Grasp the bulb only by its plastic base and do
not touch the glass. The oil from your hand could cause the bulb to
break the next time the headlamps are operated.

Note: If the bulb is accidentally touched, it should be cleaned with
rubbing alcohol before being used.

1. With the flat side of the new bulb’s plastic base facing upward, insert
the glass end of the bulb into the lamp assembly. Turn the bulb left or
right to align the grooves in the plastic base with the tabs in the lamp
assembly. When the grooves are aligned, push the bulb into the lamp
assembly until the plastic base contacts the rear of the lamp assembly.

2. Install the bulb retaining ring over the plastic base until it contacts the
rear of the socket by rotating it clockwise until you feel a “stop.”

3. Connect the electrical connector into the rear of the plastic base until
it snaps, locking it into position.

4. Install the headlamp assembly with two retainers.

5. Install the radiator cover locking it in place with three knobs.

6. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you should
not need to align it again.

Replacing front parking lamp/turn signal bulb

To remove the front parking lamp/turn signal bulb:

1. Make sure headlamp switch is in OFF position, then open the hood.

46

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Lights

2. Remove the radiator cover by turning the three knobs to the unlock
position.

3. Remove two retainers and pull
headlamp assembly forward to
expose bulb.

4. Disconnect the electrical
connector from the bulb.

5. Remove the bulb retaining ring by
rotating it counterclockwise (when
viewed from the rear) to free it
from the bulb socket, and slide the
ring off the plastic base. Keep the
ring to retain the new bulb.

6. Remove the old bulb from the lamp assembly by gently pulling it
straight back out of the lamp assembly.

To complete installation, follow the removal procedure in reverse order.

Replacing front side marker bulb

To remove the front side marker bulb:

1. Make sure headlamp switch is in the OFF position, then open the
hood.

2. Remove the radiator cover by turning the three knobs to the unlock
position.

3. Remove the screw from the
outside of the lamp.

4. Remove the nut from inside the
lamp and pull the lamp assembly
away from the vehicle.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

47

Lights

5. Rotate the bulb socket
counterclockwise and remove from
lamp assembly.

6. Carefully pull bulb straight out of
the socket and push in the new bulb
until it snaps, locking it into
position.

7. To complete installation, follow
the removal procedure in reverse
order.

Replacing tail lamp/brake/turn signal lamp bulbs

The tail lamp and brake/turn signal lamp bulbs are located in the tail
lamp assembly. Follow the same steps to replace either bulb.

1. Make sure headlamp switch is in
OFF position, then open the trunk
and remove the pin-type retainer
and carefully pull the carpet away to
expose the lamp assembly hardware.

2. Remove three nuts and the lamp
assembly from the vehicle.

3. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.

4. Pull the bulb from the socket and
push in the new bulb.

5. Install the bulb socket into the
lamp assembly by rotating it
clockwise.

6. Install the lamp assembly on the
vehicle with three nuts ensuring the
nuts are flush with the body to
prevent water from entering the trunk.

48

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Lights

7. Carefully push the carpet back in to place and install the pin-type
retainer.

Replacing license plate lamp bulbs

1. Make sure headlamp switch is in
OFF position, then remove two
screws, grommets and the license
plate lamp assembly from the trunk
lid.

2. Carefully pull the bulb from the
socket and push in the new bulb.

3. Install the lamp assembly on
trunk lid with two grommets,
ensuring the grommets are pushed
all the way into the trunk lid and secure with two screws.

Replacing backup lamp bulbs

1. Open trunk and remove bulb
socket from the trunk lid by turning
counterclockwise.

2. Pull the bulb straight out of the
socket and push in the new bulb.

3. Install the bulb socket in trunk lid
by turning clockwise.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

49

Lights

Replacing high-mount brakelamp bulbs

1. Remove two screws from the
lamp assembly.

2. Carefully lift the lamp assembly
up for access to the bulbs.

3. Carefully pull the bulb socket out
of the lamp assembly.

4. Pull the bulb straight out of the
socket and push in the new bulb.

To install, reverse the removal
procedure.

50

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

MULTI-FUNCTION LEVER

Windshield wiper: Rotate the end
of the control away from you to
increase the speed of the wipers;
rotate towards you to decrease the
speed of the wipers.

Windshield washer: Push the end
of the stalk:

• briefly: causes a single swipe of
the wipers without washer fluid.

• a quick push and hold: the wipers
will swipe three times with
washer fluid.

• a long push and hold: the wipers and washer fluid will be activated for
up to five seconds.

Courtesy wipe feature: One extra wipe will happen a few seconds
after washing the front window to clear any water that is dripping down
from the top of the windshield caused by the washing.

Note: Do not operate the washer when the washer reservoir is empty.
This may cause the washer pump to overheat. Check the washer fluid
level frequently. Do not operate the wipers when the windshield is dry.
This may scratch the glass, damage the wiper blades and cause the wiper
motor to burn out. Before operating the wiper on a dry windshield,
always use the windshield washer. In freezing weather, be sure the wiper
blades are not frozen to the windshield before operating the wipers.

Windshield wiper/washer features

The exterior lamps will turn on with the ignition on, headlamp control in
the Autolamp position and the windshield wipers are turned on.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

51

Driver Controls

TILT STEERING WHEEL

To adjust the steering wheel:

1. Pull and hold the steering wheel

release control toward you.

2. Move the steering wheel up or

down until you find the desired
location.

3. Release the steering wheel

release control. This will lock the
steering wheel in position.

Never adjust the steering wheel when the vehicle is moving.

ILLUMINATED VISOR MIRROR (IF EQUIPPED)

Lift the mirror cover to turn on the
visor mirror lamp.

Slide on rod feature (if
equipped)

Rotate the visor towards the side
window and extend it rearward for
additional sunlight coverage.

Note: To stow the visor back into
the headliner, visor must be
retracted before moving it back
towards the windshield.

52

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

CENTER CONSOLE (IF EQUIPPED)

Your vehicle may be equipped with a variety of console features. These
include:

• Utility compartment

• Power point (inside storage bin)

• Cupholders

• Air vents to the rear seating positions (heat only)

Use only soft cups in the cupholder. Hard objects can injure you
in a collision.

OVERHEAD CONSOLE WITHOUT MOON ROOF (IF EQUIPPED)

The appearance of your vehicle’s overhead console will vary according to
your option package. Some of the features in the overhead console
include a compass and HomeLink威. To program the Homelink威, refer to
Homelink威 Wireless Control System it this chapter.

Electronic compass display (if equipped)

Compass: The compass display is contained in the overhead console.

The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and
NW.

The compass reading may be affected when you drive near large
buildings, bridges, power lines and powerful broadcast antenna. Magnetic
or metallic objects placed in or on the vehicle may also affect compass
accuracy. Adjustments may need to be made to the zone and calibration
of the compass.

Compass zone adjustment

1. Determine which magnetic zone

you are in by referring to the zone
map.

2. Turn the ignition to the ON

position.

4

5

123

15

14
13

12

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

6 7 8 9 1011

53

Driver Controls

3. Press and hold the MODE control

until VAR appears in the display,
then release. The display should
show the current zone number.

4. Press the MODE control until the

desired zone number appears. The
display will flash and then return to
normal operation. The zone is now
updated.

Compass calibration adjustment

Perform this adjustment in an open
area free from steel structures and
high voltage lines:

1. Press and hold the MODE control

until CAL appears in the display
(approximately eight seconds) and
release.

2. Drive the vehicle slowly (less

than 5 km/h [3 mph]) in circles until
CAL indicator turns off in about 2–3 complete circles.

3. The compass is now calibrated.

OVERHEAD CONSOLE WITH MOON ROOF (IF EQUIPPED)

The appearance of your vehicle’s overhead console will vary according to
your option package. Some of the features in the overhead console
include Compass, Homelink, and Moon Roof controls.

Compass mode

The compass reading may be affected when you drive near large
buildings, bridges, power lines and powerful broadcast antenna. Magnetic
or metallic objects placed in, on or near the vehicle may also affect
compass accuracy.

1. Turn ignition to the ON position.

2. Start the engine.

54

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

3. From a blank display press and

release the MODE button once. The
directional heading will be
displayed.

Note: If the compass is
de-calibrated, CAL will be displayed
in the right corner of the display.
Refer to “Calibration mode” in this
section for more details.

4. The overhead console displays the compass heading in one of eight

directions: NORTH, NORTHEAST, EAST, SOUTHEAST, SOUTH,
SOUTHWEST, WEST, and NORTHWEST.

Zone variation mode

Most geographic areas (zones) have a magnetic north compass point that
varies slightly from the northerly direction on maps. A correct zone
setting will eliminate compass heading error.

To set the compass zone:

1. Press and release the MODE

button until the compass directional
heading is displayed.

2. Hold down the MODE button for

5 seconds to enter zone mode. The
display will read PRESS RESET TO
SET ZONE XX where XX is the
current zone.

3. Release the MODE button.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

55

Driver Controls

4. Determine which magnetic zone

you are in by referring to the zone
map.

5. Repeatedly press and release the

RESET button to scroll through the
zones 1–15 until the desired zone is
displayed.

6. Press the MODE button to save

the new zone setting and return to
the compass normal mode.

Note: The compass exits the zone
setting mode and returns to its previous setting after one minute of no
activity.

Note: If power is interrupted during the zone setting process, the
compass resets to the same zone it was set to before the zone change
process was started.

Calibration mode

For optimum calibration, turn off all electrical accessories (heater/air
conditioning, wipers, etc.) and make sure all vehicle doors are shut.

To calibrate the compass:

1. Press and release the MODE

button until the compass directional
heading is displayed.

4

5

123

6 7 8 9 1011

15

14
13

12

2. Hold down the MODE button for

10 seconds to enter the calibration
mode. The display will read PRESS
RESET TO DECAL.

3. Release the MODE button.

56

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

4. Press the RESET button to

de-calibrate the compass. The
display will read CIRCLE SLOWLY
TO CALIBRATE for a few seconds
and then display a direction with
CAL displayed on the right side.

5. Drive the vehicle in a tight circle

in a magnetically clean area such as
an open parking lot.

6. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]). This

will take up to three circles to complete calibration.

7. The correct compass heading will be displayed when the compass is

calibrated.
Note: If the RESET button is not pressed, the compass will exit

calibration mode after three minutes of no activity and the original
calibration data will be restored.

Note: If power is interrupted during the calibration process, the compass
resets to the original calibration data from before the calibration process
started.

HomeLink姞 wireless control system (if equipped)

The HomeLink威 Wireless Control System, located on the overhead
console, provides a convenient way to replace up to three hand-held
transmitters with a single built-in device. This feature will learn the radio
frequency codes of most transmitters to operate garage doors, entry gate
operators, security systems, entry door locks, and home or office lighting.
When programming your HomeLink威 Wireless Control System to a
garage door or gate, be sure that people and objects are out of the way
to prevent potential harm or damage. Do not use the HomeLink威
Wireless Control System with any garage door opener that lacks safety
stop and reverse features as required by U.S. federal safety standards
(this includes any garage door opener model manufactured before April
1, 1982). A garage door which cannot detect an object, signaling the
door to stop and reverse, does not meet current U.S. federal safety
standards. For more information, contact HomeLink威 at:
www.homelink.com or 1–800–355–3515. Retain the original
transmitter for use in other vehicles as well as for future programming
procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also
suggested that upon the sale of the vehicle, the programmed HomeLink威
buttons be erased for security purposes, refer to Programming in this
section.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

57

Driver Controls

Programming

Do not program the HomeLink威 with the vehicle parked in the
garage.

Note: Some vehicles may require the ignition switch to be turned to the

second (or “ACC”) position for programming and/or operation of the
HomeLink威. It is also recommended that a new battery be placed in the
hand-held transmitter of the device being programmed to HomeLink威 for
quicker training and accurate transmission of the radio-frequency signal.

1. Press and hold the two outside

buttons. The message CLEARING
CHANNELS will appear on the
HomeLink威 display.

• After about 20 seconds, the
message CHANNELS CLEARED
will appear.

Do not repeat step one to program additional hand-held transmitters to
the remaining two HomeLink威 buttons. This will erase previously
programmed hand-held transmitter signals into HomeLink威.

2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm)

away from the HomeLink威 button you wish to program (located on your
overhead console) while keeping the display in view.

58

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

3. Simultaneously press and hold

both the HomeLink威 and hand-held
transmitter button. The message
CHANNEL “X” (1,2 or 3) TRAINING
will appear on the display. Do not

release the buttons until step 4
has been completed.

Some entry gates and garage door openers may require you to replace
step 3 with procedures noted in the “Gate Operator and Canadian
Programming” section for Canadian residents.

4. When the message CHANNEL “X”

(1,2 or 3) TRAINED appears on the
display, release both the HomeLink威
and hand held transmitter buttons.

• DID NOT TRAIN will be displayed
if the channel did not properly
train.

5. Press and hold the just-trained HomeLink威 button and observe the

HomeLink威 house icon on the display. If the indicator light(s)
underneath the house icon are constant, programming is complete and
your device should activate when the HomeLink威 button is pressed and
released. Note: To program the remaining two HomeLink威 buttons,
begin with step 2 in the “Programming” section — do not repeat step 1.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

59

Driver Controls

If the indicator light(s) underneath the house icon blink rapidly for two
seconds and then turn to a continuous light, proceed with steps 6
through 8 to complete programming of a rolling code equipped device.

6. At the garage door opener receiver (motor-head unit) in the garage,

locate the “learn” or “smart” button (usually near where the hanging
antenna wire is attached to the unit).

7. Press and release the “learn” or “smart” button. (The name and color

of the button may vary by manufacturer.)
Note: There are 30 seconds in which to initiate step eight.

8. Return to the vehicle and firmly press, hold for two seconds and

release the HomeLink威 button. Repeat the press/hold/release sequence
again, and, depending on the brand of the garage door opener (or other
rolling code equipped device), repeat this sequence a third time to
complete the programming.

HomeLink威 should now activate your rolling code equipped device. To
program additional HomeLink威 buttons begin with step 2 in the
“Programming” section. For questions or comments, please contact
HomeLink at www.homelink.com or 1–800–355–3515.

Gate operator & Canadian programming

During programming, your hand-held transmitter may automatically stop
transmitting — not allowing enough time for HomeLink威 to accept the
signal from the hand-held transmitter.

After completing steps 1 and 2 outlined in the “Programming” section,
replace step 3 with the following:

Note: If programming a garage door opener or gate operator, it is
advised to unplug the device during the “cycling” process to prevent
overheating.

• Continue to press and hold the
HomeLink威 button (note step 3
in the “Programming” section)
while you press and release —
every two seconds (“cycle”)
your hand-held transmitter until
the frequency signal has been
accepted by the HomeLink威. The
message CHANNEL “X” (1,2 or 3)
TRAINING will appear on the
display.

• Proceed with step 4 in the “Programming” section.

60

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

Operating the HomeLink姞 Wireless Control System

To operate, simply press and release the appropriate HomeLink威 button.
Activation will now occur for the trained product (garage door, gate
operator, security system, entry door lock, or home or office lighting
etc.). For convenience, the hand-held transmitter of the device may also
be used at any time. In the event that there are still programming
difficulties, contact HomeLink威 at www.homelink.com or

1–800–355–3515.

Erasing HomeLink姞 buttons

To erase the three programmed buttons (individual buttons cannot be
erased):

• Press and hold the two outside
buttons. The message CLEARING
CHANNELS will appear on the
HomeLink威 display.

• After about 20 seconds, the
message CHANNELS CLEARED
will appear on the display. Do not
hold for longer that 30 seconds.
HomeLink威 is now in the train
(or learning) mode and can be
programmed at any time
beginning with step 2 in the
“Programming” section.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

61

Driver Controls

Reprogramming a single HomeLink姞 button

To program a device to HomeLink威 using a HomeLink威 button previously
trained, follow these steps:

1. Press and hold the desired

HomeLink威 button. DO NOT
release the button. The display will
read CHANNEL “X” (1,2 or 3)
TRANSMIT

2. The display will change to

CHANNEL “X” (1,2, or 3)
TRAINING after 20 seconds.
Without releasing the HomeLink威
button, follow step 2 in the
“Programming” section.

For questions or comments, contact
HomeLink威 at www.homelink.com
or 1–800–355–3515.

AUXILIARY POWER POINT (12VDC)

Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.

The auxiliary power point is located under the cup holder and ashtray
drawer in the center stack. The auxiliary power point for five passenger
vehicles is located in the floor console storage bin.

Do not use the power point for operating the cigarette lighter element (if
equipped).

To prevent the fuse from being blown, do not use the power point(s)
over the vehicle capacity of 12 VDC/180W. If the power point or cigar
lighter socket is not working, a fuse may have blown. Refer to Fuses and
relays in the Roadside Emergencies chapter for information on
checking and replacing fuses.

62

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

To prevent the battery from being discharged, do not use the power
point longer than necessary when the engine is not running.

Always keep the power point caps closed when not being used.

Cigar/Cigarette lighter (if equipped)

Do not plug optional electrical accessories into the cigarette lighter
socket.

Do not hold the lighter in with your hand while it is heating, this will
damage the lighter element and socket. The lighter will be released from
its heating position when it is ready to be used.

Improper use of the lighter can cause damage not covered by your
warranty.

POWER WINDOWS

Do not leave children unattended in the vehicle and do not let
children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free
of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

Press and hold the bottom part of
the rocker switch to open the
window. Press and hold the top part
of the rocker switch to close the
window.

One touch down

Allows the driver’s window to open
fully without holding the control
down. Press completely down on
the bottom part of the rocker switch
and release quickly. Press the rocker
switch again to stop.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

63

Driver Controls

Window lock

The window lock feature allows only
the driver to operate the power
windows.

To lock out all the window controls
except for the driver’s press the left
side of the control. Press the right
side to restore the window controls.

INTERIOR MIRROR

The interior rear view mirror has two pivot points on the support arm
which lets you adjust the mirror UP or DOWN and from SIDE to SIDE.

Do not adjust the mirror while the vehicle is in motion.

Automatic dimming interior rear view mirror (if equipped)

Your vehicle may be equipped with
an interior rear view mirror which
has an auto-dimming function. The
electronic day/night mirror will
change from the normal (high
reflective) state to the non-glare
(darkened) state when bright lights
(glare) reach the mirror. When the
mirror detects bright light from behind the vehicle, it will automatically
adjust (darken) to minimize glare.

The mirror will automatically return to the normal state whenever the
vehicle is placed in R (Reverse) to ensure a bright clear view when
backing up.

Do not block the sensors on the front and back of the interior
rear view mirror since this may impair proper mirror
performance.

Do not clean the housing or glass of any mirror with harsh
abrasives, fuel or other petroleum-based cleaning products.

64

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

EXTERIOR MIRRORS

Power side view mirrors

To adjust your mirrors:

1. Select to adjust the left

mirror or
mirror.

2. Move the control in the direction

you wish to tilt the mirror.

3. Return to the center position to

lock mirrors in place.

to adjust the right

Driver Controls

Heated outside mirrors

Both mirrors are heated
automatically to remove ice, mist
and fog when the rear window
defrost is activated.

Do not remove ice from the
mirrors with a scraper or
attempt to readjust the mirror
glass if it is frozen in place.
These actions could cause
damage to the glass and mirrors.

Fold-away mirrors

Fold the side mirrors in carefully
when driving through a narrow
space, like an automatic car wash.

(if equipped)

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

65

Driver Controls

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)

The accelerator and brake pedal
should only be adjusted when the
vehicle is stopped and the gearshift
lever is in the P (Park) position.

Press and hold the rocker control to
adjust accelerator and brake pedal.

• Press the right side of the control to adjust the pedals toward you.

• Press the left side of the control to adjust the pedals away from you.

The adjustment allows for approximately 2.5 inches (65 mm) of
maximum travel.

Never adjust the accelerator and brake pedal with feet on the
pedals while the vehicle is moving.

SPEED CONTROL (IF EQUIPPED)

With speed control set, you can maintain a set speed without keeping
your foot on the accelerator pedal.

Do not use the speed control in heavy traffic or on roads that
are winding, slippery or unpaved.

Setting speed control

The controls for using your speed
control are located on the steering
wheel for your convenience.

1. Press the ON control and release

it.

2. Accelerate to the desired speed.

66

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

3. Press the SET + control and

release it.

4. Take your foot off the accelerator

pedal.

5. The indicator

equipped) on the instrument cluster
will turn on.

Note:

• Vehicle speed may vary momentarily when driving up and down a
steep hill.

• If the vehicle speed increases above the set speed on a downhill, you
may want to apply the brakes to reduce the speed.

• If the vehicle speed decreases more than 10 mph (16 km/h) below
your set speed on an uphill, your speed control will disengage.

Disengaging speed control

To disengage the speed control:

• Depress the brake pedal

Disengaging the speed control will not erase previous set speed.

light (if

Resuming a set speed

Press the RESUME control and
release it. This will automatically
return the vehicle to the previously
set speed.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

67

Driver Controls

Increasing speed while using speed control

There are two ways to set a higher
speed:

• Press and hold the SET + control
until you get to the desired
speed, then release the control.
You can also use the SET +
control to operate the Tap-Up
function. Press and release this
control to increase the vehicle set
speed in small amounts by 1 mph
(1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the
vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control

There are two ways to reduce a set
speed:

• Press and hold the SET - control
until you get to the desired
speed, then release the control.
You can also use the SET ­control to operate the Tap-Down
function. Press and release this
control to decrease the vehicle
set speed in small amounts by 1
mph (1.6 km/h).

• Depress the brake pedal until the
desired vehicle speed is reached,
press the SET + control.

68

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

Turning off speed control

There are two ways to turn off the speed control:

• Depress the brake pedal. This will
not erase your vehicle’s
previously set speed.

• Press the speed control OFF
control.

Note: When you turn the speed
control or the ignition off, your
speed control set speed memory is
erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

Driving while distracted can result in loss of vehicle control,

accident and injury. Ford strongly recommends that drivers use
extreme caution when using any device that may take their focus off
the road. The drivers primary responsibility is the safe operation of
their vehicle. Only use steering wheel controls and other devices not
essential to the driving task when it is safe to do so.

Audio control features

In Radio mode:

• Press NEXT to select the next
preset station within the current
radio band.

In Tape mode:

• Press NEXT to listen to the next
selection on the tape.

In CD mode:

• Press NEXT to listen to the next
track on the disc.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

69

Driver Controls

In any mode:

• Press VOL + or - to adjust the
volume.

Climate control features

• Press TEMP + or - to adjust
temperature.

MOON ROOF (IF EQUIPPED)

Do not let children play with the moon roof or leave children
unattended in the vehicle. They may seriously hurt themselves.

When closing the moon roof, you should verify that it is free of
obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

70

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

To vent the moon roof:

• Press and hold the control
forward to raise the moon roof to
the vent position (when the glass
panel is closed).

To open the moon roof:

• For one-touch operation, press
the control rearward and release;
this will fully open the moon roof.

• To stop one-touch operation at
the desired position, press the control in any direction and release.

To close the moon roof:

• Press and hold the control forward.

• To close from the vent position, press and hold the control rearward.

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)

The HomeLink威 Wireless Control System, located on the overhead
console, provides a convenient way to replace up to three hand-held
transmitters with a single built-in device. This feature will learn the radio
frequency codes of most transmitters to operate garage doors, entry gate
operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to
a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage
door opener that lacks safety stop and reverse features as required by
U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLink威 at: www.homelink.com or 1–800–355–3515.

Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLink威 equipped vehicle
purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelink威 buttons be erased for security purposes, refer to
Programming in this section.

71

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

Programming

Do not program HomeLink威 with the vehicle parked in the garage.
Note: Some vehicles may require the ignition switch to be turned to the

second (or “ACC”) position for programming and/or operation of the
HomeLink威. It is also recommended that a new battery be placed in the
hand-held transmitter of the device being programmed to HomeLink威 for
quicker training and accurate transmission of the radio-frequency signal.

1. Press and hold the two outside

buttons releasing only when the
indicator light begins to flash after
20 seconds. Do not repeat Step 1
to program additional hand-held
transmitters to the remaining two
HomeLink威 buttons. This will erase
previously programmed hand-held
transmitter signals into HomeLink威.

2.

Position the end of your hand-held

transmitter 1–3 inches (2–8 cm)
away from the HomeLink威 button you wish to program (located on your
overhead console) while keeping the indicator light in view.

3. Simultaneously press and hold

both the chosen HomeLink威 and
hand-held transmitter buttons until
the HomeLink威 indicator light
changes from a slow to a rapidly
blinking light. Now you may release
both the HomeLink威 and hand-held
transmitter buttons.

Note: Some entry gates and garage
door openers may require you to
replace Step 3 with procedures
noted in the “Gate Operator and Canadian Programming” section for
Canadian residents.

4. Firmly press, hold for five seconds and release the programmed

HomeLink威 button up to two separate times to activate the door. If the
door does not activate, press and hold the just-trained HomeLink威
button and observe the indicator light.

• If the indicator light stays on constantly, programming is complete

and your device should activate when the HomeLink威 button is pressed
and released.

72

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

• If the indicator light blinks rapidly for two seconds and then turns

to a constant light continue with “Programming” Steps 5 through
7 to complete programming of a rolling code equipped device (most

commonly a garage door opener).

5. At the garage door opener receiver (motor-head unit) in the garage,

locate the “learn” or “smart” button (usually near where the hanging
antenna wire is attached to the unit).

6. Firmly press and release the “learn” or “smart” button. (The name and

color of the button may vary by manufacturer.)
Note: There are 30 seconds in which to initiate Step 7.

7. Return to the vehicle and firmly press, hold for two seconds and

release the HomeLink威 button. Repeat the press/hold/release
sequence again and, depending on the brand of the garage door opener
(or other rolling code equipped device), repeat this sequence a third
time to complete the programming.

HomeLink威 should now activate your rolling code equipped device. To
program additional HomeLink威 buttons begin with Step 2 in the
“Programming” section. For questions or comments, please contact
HomeLink at www.homelink.com or 1–800–355–3515.

Gate Operator & Canadian Programming

During programming, your
hand-held transmitter may
automatically stop transmitting —
not allowing enough time for
HomeLink威 to accept the signal
from the hand-held transmitter.

After completing Steps 1 and 2
outlined in the “Programming”
section, replace Step 3 with the
following:

Note:

If programming a garage door opener or gate operator, it is advised

to unplug the device during the “cycling” process to prevent overheating.

• Continue to press and hold the HomeLink威 button (note Step 3 in the
“Programming” section) while you press and release — every two
seconds (“cycle”) your hand-held transmitter until the frequency
signal has been accepted by the HomeLink威. The indicator light will
flash slowly and then rapidly after HomeLink威 accepts the radio
frequency signal.

• Proceed with Step 4 in the “Programming” section.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

73

Driver Controls

Operating the HomeLink姞 Wireless Control System

To operate, simply press and release
the appropriate HomeLink威 button.
Activation will now occur for the
trained product (garage door, gate
operator, security system, entry
door lock, or home or office lighting
etc.). For convenience, the
hand-held transmitter of the device
may also be used at any time. In the
event that there are still
programming difficulties, contact
HomeLink威 at www.homelink.com or 1–800–355–3515.

Erasing HomeLink姞 buttons

To erase the three programmed
buttons (individual buttons cannot
be erased):

• Press and hold the two outer
HomeLink威 buttons until the
indicator light begins to
flash-after 20 seconds. Release
both buttons. Do not hold for
longer that 30 seconds.

HomeLink威 is now in the train (or
learning) mode and can be programmed at any time beginning with Step
2inthe“Programming” section.

Reprogramming a single HomeLink姞 button

To program a device to HomeLink威 using a HomeLink威 button previously
trained, follow these steps:

1. Press and hold the desired HomeLink威 button. Do NOT release the

button.

2. The indicator light will begin to flash after 20 seconds. Without

releasing the HomeLink威 button, follow Step 2 in the “Programming”
section.

For questions or comments, contact HomeLink威 at www.homelink.com
or 1–800–355–3515.

74

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

MESSAGE CENTER (IF EQUIPPED)

With the ignition in the ON position,
the message center, located on your
instrument cluster, displays
important vehicle information

through a constant monitor of
vehicle systems. You may select

display features on the message
center for a display of status. The
system will also notify you of potential vehicle problems with a display of
system warnings followed by a long indicator chime.

Your display can show up to 3 reconfigurable telltales at one time. What
ever is displayed in the top left corner has the highest priority. Premium
Display Severity Indicator (located under the Message Center): Indicates
severity of the information being displayed on the premium display. Red
for high severity, amber for medium severity, and non-lit for information
only. For example, a door ajar warning would be accompanied by a red
indicator, low fuel by an amber indicator, and fuel economy by an
absence of the indicator. The indicator always illuminates with the
highest severity rating of the warnings displayed.

Selectable features

Select

Press this control to select functions shown in the INFO menu and
SETUP menu.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

75

Driver Controls

Reset

Press this control to reset functions shown in the INFO menu and
SETUP menu.

Info menu

This control displays the following control displays:

• Trip odometer/Odometer

• Distance to Empty

• Average Fuel Economy

• Instantaneous Fuel Economy

• Trip elapsed drive time

Odometer/Trip odometer

Refer to Gauges in the Instrument Cluster chapter.

Distance to empty (DTE)

Selecting this function from the
INFO menu estimates approximately
how far you can drive with the fuel
remaining in your tank under
normal driving conditions.
Remember to turn the ignition OFF
when refueling to allow this feature
to correctly detect the added fuel.

The DTE function will display LOW FUEL LEVEL and sound a tone for
one second when you have approximately 50 miles (80 km) to empty. If
you RESET this warning message, this display and tone will return
within 10 minutes or 10 miles(16 km).

DTE is calculated using a running average fuel economy, which is based
on your recent driving history of 500 miles (800 km). This value is not
the same as the average fuel economy display. The running average fuel
economy is reinitialized to a factory default value if the battery is
disconnected.

76

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

Average fuel economy (AFE)

Select this function from the INFO
menu to display your average fuel
economy in miles/gallon or liters/100
km.

If you calculate your average fuel
economy by dividing gallons of fuel
used by 100 miles traveled
(kilometers traveled by liters used),
your figure may be different than displayed for the following reasons:

• Your vehicle was not perfectly level during fill-up

• Differences in the automatic shut-off points on the fuel pumps at

service stations

• Variations in top-off procedure from one fill-up to another

• Rounding of the displayed values to the nearest 0.1 gallon (liter)

1. Drive the vehicle at least 5 miles (8 km) with the speed control

system engaged to display a stabilized average.

2. Record the highway fuel economy for future reference.

It is important to press the RESET control (press and hold RESET for 2
seconds in order to reset the function) after setting the speed control to
get accurate highway fuel economy readings.

Instantaneous fuel economy

Select this function from the INFO
menu to display your instantaneous
fuel economy. This will display your
fuel economy as a Bar Graph
ranging from

to

Your vehicle must be moving to
calculate instantaneous fuel
economy. When your vehicle is not moving, this function shows
or no bars illuminated. Instantaneous fuel economy cannot be reset.

excellent economy.

poor economy

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

one

77

Driver Controls

Trip elapsed drive time

Select this function from the INFO
menu to display a timer.

To operate the Trip Elapsed Drive
Time perform the following:

1. Press and release RESET in order

to start the timer.

2. Press and release RESET to

pause the timer.

3. Press and hold RESET for 2 seconds in order to reset the timer to

zero.

Setup menu

Press this control for the following displays:

• System Check

• Display (odometer/speedometer)

• Text Size (normal/large)

• Units (English/Metric)

• Language

• Oil Minder Start Value

System check

Selecting this function from the
SETUP menu causes the message
center to cycle through each of the
systems being monitored. For each
of the monitored systems, the
message center will indicate either
an OK message or a warning
message for three seconds.

Pressing the SELECT control cycles the message center through each of
the systems being monitored.

78

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

The sequence of the system check report and how it appears in the
message center is as follows:

1. OIL LIFE

— PRESS RESET IF NEW OIL

2. WASHER FLUID

3. AIR SUSPENSION (if equipped))

4. RECONFIGURABLE TELLTALES

—OK
— FAILED RED
— FAILED AMBER

Display Type

1. Select this function from the

SETUP menu.

2. Press the SELECT control to

change the display.

Text Size

1. Select this function from the

SETUP menu.

2. Press the SELECT control to

change text size.

Units (English/Metric)

1. Select this function from the

SETUP menu for the current units
to be displayed.

2. Press the SELECT control to

change from English to Metric.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

79

Driver Controls

Language

1. Select this function from the

SETUP menu for the current
language to be displayed.

2. Pressing the SELECT control

cycles the message center through
each of the language choices.

Oil Minder Start Value

1. Select this function from the

SETUP control for the current
display mode.

2. Press the SELECT control to

change oil value.

System warnings

System warnings alert you to possible problems or malfunctions in your
vehicle’s operating systems.

In the event of a multiple warning situation, the message center will
cycle the display to show all warnings by displaying each one for 4
seconds.

The message center will display the last selected feature if there are no
more warning messages. This allows you to use the full functionality of
the message center after you acknowledge the warning by pressing the
RESET control and clearing the warning message.

Warning messages that have been reset are divided into three categories:

• They cannot be reset until the condition is corrected.

• They will reappear on the display ten minutes from the reset.

80

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

• They will not reappear until an ignition OFF-ON cycle has been
completed.

This acts as a reminder that these warning conditions still exist within
the vehicle.

Warning display Status

Door Ajar Warning cannot be reset
Coolant over temperature Warning returns after 10 minutes
Powertrain malfunction
Check fuel cap
Check air suspension
Low fuel
Overdrive ON/OFF Warning returns after the ignition key
Trunk ajar
Low tire pressure
Tire pressure monitor fault
Tire pressure sensor fault
Check compass module
Low washer fluid
Change engine oil

DOOR AJAR. Displayed when a door is not completely closed.
POWERTRAIN MALFUNCTION. Displayed when the powertrain is not

operating properly. If the warning stays on or continues to come on,
contact your authorized dealer as soon as possible.

COOLANT OVER TEMPERATURE. Displayed when the engine
coolant is overheating. Stop the vehicle as soon as safely possible, turn
off the engine and let it cool. Check the coolant and coolant level. Refer
to Engine coolant in the Maintenance and Specifications chapter. If
the warning stays on or continues to come on, contact your authorized
dealer as soon as possible.

is turned from OFF to ON.

Never remove the coolant reservoir cap while the engine is
running or hot.

CHECK FUEL CAP. Displayed when the fuel filler cap is not properly
installed. Check the fuel filler cap for proper installation. Refer to Fuel
filler cap in the Maintenance and Specifications chapter.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

81

Driver Controls

CHECK AIR SUSPENSION. Displayed when the air suspension system
is not operating properly. If this message is displayed while driving, pull
off the road as soon as safely possible. For more information, refer to Air
suspension in the Driving chapter.

LOW FUEL. Displayed as an early reminder of a low fuel condition.
Warning message can be reset by pressing the RESET button, but will
return after 10 minutes. If any other button is pressed besides RESET,
the message ’’PRESS RESET TO CLEAR’’ will appear in the Message
Center. Once this message disappears (after approximately 2 seconds),
press RESET to clear the warning.

TRUNK AJAR. Displayed when the trunk is not completely closed.
OVERDRIVE ON/OFF. Displayed when the overdrive is enabled or

disabled.
LOW TIRE PRESSURE. Displayed when one or more tires on your

vehicle have low tire pressure. Refer to Inflating Your Tires in the
Tires, Wheels and Loading chapter.

TIRE PRESSURE MONITOR FAULT. Displayed when the Tire
Pressure Monitoring System is malfunctioning. If the warning stays on or
continues to come on, have the system inspected by your authorized
dealer.

TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressure
sensor is malfunctioning, or your spare tire is in use (Note: this includes
the use of the optional full-sized matching spare tire and wheel). For
more information on how the system operates under these conditions,
refer to Understanding Your Tire Pressure Monitoring System in the
Tires, Wheels and Loading chapter. If the warning stays on or
continues to come on, have the system inspected by your authorized
dealer.

CHECK COMPASS MODULE. Displayed when the compass is not
operating properly. If the warning stays on or continues to come on,
contact your authorized dealer as soon as possible.

LOW WASHER FLUID. Indicates the washer fluid reservoir is less than
one quarter full. Check the washer fluid level. Refer to Windshield
washer fluid in the Maintenance and Specifications chapter.

CHANGE ENGINE OIL. Displayed when the engine oil life remaining is
5 percent or less. When oil life left is between 5% and 0%, the CHANGE
OIL SOON message will be displayed. When oil life left reaches 0%, the
OIL CHANGE REQUIRED message will be displayed.

An oil change is required whenever indicated by the message center and
according to the recommended maintenance schedule. USE ONLY
RECOMMENDED ENGINE OILS.

82

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Driver Controls

To reset the oil monitoring system to 100% after each oil change
[approximately 7,500 miles (12,070 km) or 6 months] perform the
following:

1. Press and hold the RESET

control for 2 seconds and release.
Oil life is set to 100% and “OIL LIFE
XXX% HOLD RESET IF NEW OIL”
is displayed.

2. Press and hold the RESET

control for 3 seconds and release.
Oil life is set to 100% and “OIL LIFE
START VALUE SET TO XXX%” is
displayed.

POSITIVE RETENTION FLOOR MAT

Do not install additional floor mats on top of the factory installed
floor mats as they may interfere with the accelerator or the

brake pedals.

Position the driver floor mat so that
the eyelet is over the pointed end of
the retention post and rotate
forward to lock in. Make sure that
the mat does not interfere with the
operation of the accelerator or the
brake pedal. To remove the floor
mat, reverse the installation
procedure.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

83

Driver Controls

INTERIOR TRUNK CONTROL

The remote trunk release control is
located on the driver’s door trim
panel and can be operated at any
time.

You can render the switch
inoperable by locking the button
with your master key.

If equipped with a perimeter alarm system, the remote trunk release
control and power door locks will be disabled when the vehicle perimeter
alarm system is armed. This control will not work until the vehicle
perimeter alarm system is disarmed. Refer to Perimeter Alarm System
in the Locks and Security chapter.

84

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

KEYS

The vehicle is equipped with a master key which will access the vehicle’s
doors, trunk, glove box, ignition and remote trunk release.

POWER DOOR LOCKS

Power door trim switch inhibit

This feature disables the power door locks and trunk interior release
switches if all doors are closed and the perimeter alarm becomes armed.

Once the power door trim switches are disabled, they can only become
active when perimeter alarm is disarmed.

Press control to unlock all vehicle
doors.

Press control to lock all vehicle
doors.

Smart locks (if equipped)

With the key in any ignition position, and either the driver’s or
passenger’s door open, the doors cannot be locked using the power door
lock switches.

The vehicle may still be locked with the key in the ignition, and
performing one of the following actions:

• Pressing the manual lock button on the door.

• Operating the remote entry transmitter (if equipped).

• Operating the keyless entry keypad (if equipped).

• Operating the driver’s door with a key.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

85

Locks and Security

Autolock (if equipped)

This feature automatically locks all vehicle doors when:

• all doors are closed,

• the engine is running,

• you shift into any gear, putting the vehicle in motion, and

• the vehicle’s speed is greater than 3 mph (5 km/h).

Auto-relock

The autolock feature repeats when:

• a door is opened and closed while the engine is running,

• you shift into any gear, putting the vehicle in motion, and

• the vehicle’s speed is greater than 3 mph (5 km/h).

Auto-unlock

The auto-unlock feature will unlock all doors when:

• the ignition has been in the 3 (ON) position, all doors are closed, and
the vehicle has been in motion at a speed greater than 12 mph (20
km/h),

• the vehicle has then come to a stop and the ignition is turned to the 2
(ACCESSORY) or 1 (OFF/LOCK) position, and

• the driver door is opened {within ten minutes after the ignition was
transitioned to the 2 (ACCESSORY) or 1 (OFF/LOCK) position}.

Note: The vehicle doors will not auto-unlock if the vehicle has been
electronically locked prior to the driver door being opened.

Deactivating/activating the autolock or auto-unlock feature

Automatic door locks can also be turned on/off through the following
procedure:

You must complete Steps 1-7 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait at least 30 seconds. Note: Before following the procedure, make
sure that the ignition is in the 1 (OFF/LOCK) position and all vehicle
doors, the hood, and the decklid are closed.

1. Turn the ignition to the 3 (ON) position.

2. Press the power door unlock control on the door panel three times.

3. Turn the ignition from the 3 (ON) to the 1 (OFF/LOCK) position.

86

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

4. Press the power door unlock control three times.

5. Turn the ignition back to the 3 (ON) position.

6. The door locks will lock/unlock to confirm programming mode is

entered/active.

7. With the ignition still in the 3 (ON) position, for the autolock

feature, press the unlock control once then press the lock control once.
The horn will chirp once if autolock was deactivated or twice (one short
and one long chirp) if autolock was activated. For the auto-unlock
feature, press the lock control once, then press the unlock control once.
The horn will chirp once if auto-unlock was deactivated or twice (one
short and one long chirp) if auto-unlock was activated.

If any door, the hood, or the deck lid is open, the horn will chirp
twice, and the procedure will need to be performed again.

8. After having waited the necessary time for the programming to

confirm, turn the ignition to the 1 (OFF/LOCK) position.
Once disabled, the autolock or auto-unlock feature can be enabled by

repeating the procedure in Steps 1–8.

CHILDPROOF DOOR LOCKS

When these locks are set, the rear
doors cannot be opened from the
inside. The rear doors can be
opened from the outside when the
doors are unlocked.

The childproof locks are located on
rear edge of each rear door and
must be set separately for each
door. Setting the lock for one door
will not automatically set the lock
for both doors.

Move lock control up to engage the
childproof lock. Move control down
to disengage childproof locks.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

87

Locks and Security

INTERIOR LUGGAGE COMPARTMENT RELEASE

Your vehicle is equipped with a mechanical interior luggage compartment
release handle that provides a means of escape for children and adults in
the event they become locked inside the luggage compartment.

Adults are advised to familiarize themselves with the operation and
location of the release handle.

To open the luggage compartment
door (lid) from within the luggage
compartment, pull the illuminated
“T” shaped handle and push up on
the trunk lid. The handle is
composed of a material that will
glow for hours in darkness following
brief exposure to ambient light.

The “T” shaped handle will be
located either on the luggage
compartment door (lid) or inside
the luggage compartment near the
tail lamps.

Keep vehicle doors and

luggage compartment
locked and keep keys and remote
transmitters out of a child’s reach.
Unsupervised children could lock
themselves in the trunk and risk
injury. Children should be taught
not to play in vehicles.

On hot days, the temperature in the trunk or vehicle interior can

rise very quickly. Exposure of people or animals to these high
temperatures for even a short time can cause death or serious
heat-related injuries, including brain damage. Small children are
particularly at risk.

88

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

REMOTE ENTRY SYSTEM (IF EQUIPPED)

This device complies with part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may
cause undesired operation.

The remote entry system allows you to lock or unlock all vehicle doors
without a key.

The remote entry features operate
with the ignition in any position,
except in the 3 (ON) , with the
transmission not in either P (Park)
or N (Neutral).

If there are problems with the
remote entry system, make sure to
take ALL remote entry
transmitters with you to the
authorized dealer in order to aid in
troubleshooting the problem.

Unlocking the doors

1. Press and release to unlock the driver’s door. Note: The interior
lamps will illuminate.

2. Press

and release again within five seconds to unlock all the doors.

Locking the doors

Press once to lock all the doors. Upon the first press the doors will
lock and the parklamps/taillamps will flash once.

Press
vehicle was successfully locked. Note: If all vehicle doors, the hood, and
the trunk are closed upon the second press of the , the horn will
chirp once and the parklamps/taillamps will flash once to confirm the
successful locking.

Upon the second press of the
not securely closed the horn will chirp twice to warn that successfully
locking was not complete. The park/taillamps will NOT flash if any door
is ajar.

again within three seconds to receive confirmation that the

, if any door, the hood, or the trunk is

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

89

Locks and Security

Car finder

Press
parklamps/taillamps will flash. It is recommended that this method be
used to locate your vehicle, rather than using the panic alarm.

Sounding a panic alarm

Press
panic alarm only works with the ignition in the 1 (OFF/LOCK) position.

Press
the alarm by turning the ignition to the 3 (ON) position.

Opening the trunk

Press once to open the trunk.

• Ensure that the trunk is closed and latched before driving your
vehicle. Failure to properly latch the trunk may cause objects to fall
out or block the driver’s rear view.

This feature will not work with a vehicle speed greater than 3 mph (5
km/h) if the ignition is in the 2 (ACCESSORY) or 3 (ON) position.

Replacing the battery

The remote entry transmitter uses one coin type three-volt lithium
battery CR2032 or equivalent.

To replace the battery:

1. Twist a thin coin between the two

halves of the remote entry
transmitter near the key ring. DO
NOT TAKE THE RUBBER COVER
AND CIRCUIT BOARD OFF THE
FRONT HOUSING OF THE
REMOTE ENTRY TRANSMITTER.

twice within 3 seconds. The horn will chirp and the

on the remote transmitter to activate the alarm. Note: The

a second time to deactivate the alarm. You may also deactivate

90

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

2. Do not wipe off any grease on the

battery terminals on the back
surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when

disposing of transmitter batteries.

4. Insert the new battery. Refer to the diagram inside the remote entry

transmitter for the correct orientation of the battery. Press the battery
down to ensure that the battery is fully seated in the battery housing
cavity.

5. Snap the two halves back together.

Note: Replacement of the battery will not cause the remote transmitter
to become deprogrammed from your vehicle. The remote transmitter
should operate normally after battery replacement.

Replacing lost transmitters

Take all your vehicle’s transmitters to your authorized dealer if service is
required.

If a remote transmitter has been lost and you would like to remove it
from the vehicle’s memory, or you would like to purchase additional
remote transmitters and have them programmed to your vehicle:

• Take all your vehicle’s transmitters to your authorized dealer for
programming, or

• Perform the following programming procedure yourself:

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

91

Locks and Security

Note: Ensure the brake pedal is not
depressed during this sequence.

Place the key in the ignition and
cycle from 1 (OFF/LOCK) to 3 (ON)
eight times in rapid succession
within 10 seconds. After doors
lock/unlock, press any control on all
transmitters (up to four). After
pressing the control on each remote
transmitter, the door will lock and
unlock. If programming multiple remote transmitters, you must press the
control buttons on each remote transmitter within 7 seconds of each
other to remain in programming mode. When completed, turn the
ignition to 1 (OFF/LOCK).

All transmitters must be programmed at the same time.

• When completed, turn the ignition to the 1 (OFF/LOCK) position and
wait at least 20 seconds in order to use the recently programmed
transmitter(s).

• All transmitters must be programmed during the same programming
cycle. A transmitter that is not programmed within the same
programming cycle will be erased and will no longer operate your
vehicle’s locks. If this occurs, you will have to reprogram all the
transmitters again, as you cannot just “add” a transmitter.

Illuminated entry

The interior lamps illuminate when the remote entry system is used to
unlock the door(s) or sound the personal alarm.

The illuminated entry system will turn off the interior lights if:

• the ignition switch is turned to the 2 (ACCESSORY), 3 (ON) or 4
(START) positions, or

• the remote transmitter lock control is pressed, or

• after 25 seconds of illumination.

The dome lamp control must not be set to the off position for the
illuminated entry system to operate.

The inside lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

The battery saver will shut off the interior lamps 30 minutes after the
last door is closed, or after 10 minutes if the last door is left open.

2

1

3

4

92

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

Radio type approval numbers for remote entry receiver

If the type approval of your remote entry system is inspected in one of
the countries listed in the following table, refer to the corresponding
approval number:

Remote entry receiver certification numbers

Gabon 01070305/ARTEL/GABTEL

Jordan CAZ/ENG/CA/04/11/1

Zambia TRC/LPD/2004/28

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.

KEYLESS ENTRY SYSTEM (IF EQUIPPED)

With the keyless entry keypad, you
can:

• lock or unlock the vehicle doors
without using the key.

• open the trunk.

See also Remote entry system in this chapter for more information.
Your vehicle has a factory-set 5–digit code that operates the keyless

entry system. You can also program your own 5–digit personal entry
code.

The factory-set code is located:

• On the owner’s wallet card in the glove compartment, or

• At your dealer.

When using the keyless entry keypad, press the middle of each button in
order to ensure a good activation.

1 2

3

4567890

Programming a personal entry code

You can program up to three personal codes to unlock your vehicle.
These codes do not replace the permanent code that the authorized
dealer gave you.

To create your own personal entry code:

1. Enter the factory set code. Note: The keypad will illuminate when

pressed.

2. Within five seconds press 1 • 2 on the keypad to enter the

programming mode.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

93

Locks and Security

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. Press 1 • 2 to store the first personal code.

5. The doors will lock then unlock to confirm programming of the new

code.
To store a second personal code:

1. Enter the factory set code.

2. Within five seconds press 1 • 2 on the keypad to enter the

programming mode.

3. Enter a second personal 5-digit code. Each number must be entered

within five seconds of each other.

4. Press 3 • 4 to store the second personal code.

5. The doors will again lock then unlock to confirm programming of the

new code.
To store a third personal code:

1. Enter the factory set code.

2. Within five seconds press 1 • 2 on the keypad to enter the

programming mode.

3. Enter a third personal 5-digit code. Each number must be entered

within five seconds of each other.

4. Press 5 • 6 (or 7 • 8, or 9 • 0, or wait five seconds) to store the third

personal code.

5. The doors will again lock then unlock to confirm programming of the

new code.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory set code will work even if you have set your own personal

code.

Erasing personal code

To erase all of the personal entry codes programmed to a vehicle:

1. Enter the factory-set code.

2. Press and release 1 • 2 within 5 seconds of step 1.

3. Press and hold 1 • 2 for two seconds. All of the vehicle doors will lock

and then unlock to confirm erasure.

94

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

Unlocking the doors and releasing the trunk with the keyless entry
system

To unlock the driver door, enter either the factory-set code or personal
code (each digit pressed within 5 seconds of prior digit). The interior
lamps will illuminate.

• To unlock all doors, enter the factory-set code or personal code
(driver door unlocks) and press 3 • 4 within five seconds.

• To release the trunk, enter the factory-set code or personal code
(driver door unlocks) and press 5 • 6 within five seconds.

After the factory-set code or personal code has been entered, you can
unlock all doors (press 3 • 4) and release the trunk (press 5 • 6) as
long as the controls are pressed within 5 seconds of each other.

Locking doors with the keyless entry system

It is not necessary to enter the factory-set code prior to locking all doors.
To lock the doors, press 7 • 8 and press 9 • 0 at the same time. Note:
The doors will not lock if the driver door is ajar.

Anti-scan feature

If the wrong code has been entered 7 times (35 consecutive button
presses), the keypad will go into an anti-scan mode. This mode disables
the keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after:

• one minute of keypad inactivity.

• pressing the

• the ignition is turned to the 3 (ON) position.

control on the remote entry transmitter.

SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM

SecuriLock™ passive anti-theft system is an engine immobilization
system. This system is designed to help prevent the engine from being
started unless a coded key programmed to your vehicle is used. The
use of the wrong type of coded key may lead to a “no-start” condition.

This device complies with part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may
cause undesired operation.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

95

Locks and Security

Radio type approval numbers for Immobiliser System PATS XCVR

If the type approval of your immobilizer system is inspected in one of the
countries listed in the following table, refer to the corresponding
approval number:

Immobiliser System PATS XCVR certification numbers

TX Frequency: 134,2 kHz -8,1 dBµA/m @ 10 m

Country Name Type Approval Number

American Samoa (USA) See USA

Bahrain DLM/GEN/18/18/16

Barbados 340/3 Vol.II

Canada CANADA: 3043104475A

China CMII ID:2005DJ0428

Ghana SPLS / -485 / 2001

Guam (USA) See USA

Jordan 4/U/U/4250

Kenya CCK/ES/100/0

Kuwait M.C/U.S.0 /5/7-12579

Mauritius TA/2005/15

Mayotte (F)

Mexico RLVVIVP03-324

Morocco MR 1299 ANRT 2004

Netherlands Antilles (NL)

Nicaragua NCG-CE-04-004

Northern Mariana Islands See USA

Oman OMA/1265(A) 1308/2001

Puerto Rico See USA

Qatar QTEL/SR/2003/R-276
Saudi Arabia (10/1900)
South Korea R-LPD1-04-0145

Tunisia 269/MAT/2004

United Arabian Emirates 5/10-2/3274/3774

Uruguay 025/FR/2003

USA NT8-15607PAT3XCVR

Zambia CAZ/ENG/CA/2005/02/8

96

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.

Your vehicle comes with two coded keys; additional coded keys may be
purchased from your authorized dealer. The authorized dealer can
program your spare keys to your vehicle or you can program the keys
yourself. Refer to Programming spare keys for instructions on how to
program the coded key.

Note: The SecuriLock™ passive anti-theft system is not compatible with
non-Ford aftermarket remote start systems. Use of these systems may
result in vehicle starting problems and a loss of security protection.

Note: Large metallic objects, electronic devices that are used to
purchase gasoline or similar items, or a second coded key on the same
key chain may cause vehicle starting issues. You need to prevent these
objects from touching the coded key while starting the engine. These
objects will not cause damage to the coded key, but may cause a
momentary issue if they are too close to the key when starting the
engine. If a problem occurs, turn the ignition to the 1 (OFF/LOCK)
position, remove all objects on the key chain away from the coded key
and restart the engine.

Anti-theft indicator

The anti-theft indicator is the flashing red indicator located on the dash
panel.

• When the ignition is in the 1 (OFF/LOCK) position, the indicator will
flash once every 2 seconds to indicate the SecuriLock™ system is
functioning as a theft deterrent.

• When the ignition is in the 3 (ON) position, the indicator will glow for
3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock™ system, the indicator will flash
rapidly or glow steadily when the ignition is in the 3 (ON) position. If
this occurs, the vehicle should be taken to an authorized dealer for
service.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

97

Locks and Security

Automatic arming

The vehicle is armed immediately
after switching the ignition to the 1
(OFF/LOCK) position.

The theft indicator on the
instrument panel will flash every
two seconds when the vehicle is
armed.

Automatic disarming

Switching the ignition to the 3 (ON) position with a coded key disarms
the vehicle.

• The theft indicator on the instrument panel will illuminate for three
seconds and then go out.

• If the theft indicator stays on for an extended period of time or
flashes rapidly, have the system serviced by your authorized dealer.

Replacement keys

If your keys are lost or stolen and you don’t have an extra coded key,
you will need to have your vehicle towed to an authorized dealer. The
key codes need to be erased from your vehicle and new coded keys will
need to be programmed.

Replacing coded keys can be very costly. Store an extra programmed key
away from the vehicle in a safe place to help prevent any
inconveniences. Please visit an authorized dealer to purchase additional
spare or replacement keys.

2

1

3

4

Programming spare keys

A maximum of eight keys can be coded to your vehicle. Only
SecuriLock™ keys can be used. To program a coded key yourself, you
will need two previously programmed coded keys (keys that already
operate your vehicle’s engine) and the new unprogrammed key(s) readily
accessible for timely implementation of each step in the procedure.

If two previously programmed coded keys are not available, you must
bring your vehicle to your authorized dealer to have the spare coded
key(s) programmed.

98

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

Locks and Security

Please read and understand the entire procedure before you begin.

1. Insert the first previously

programmed coded key into the
ignition and turn the ignition from 1
(OFF/LOCK) to the 3 (ON) position
(maintain ignition in 3 (ON) for at
least one second).

2. Turn ignition to 1 (OFF/LOCK)

and remove the first coded key
from the ignition.

3. Within ten seconds of removing

the first coded key, insert the second previously programmed coded
key into the ignition and turn the ignition from 1 (OFF/LOCK) to the 3
(ON) position (maintain ignition in 3 (ON) for at least one second but no
more than ten seconds).

4. Turn the ignition to 1 (OFF/LOCK) and remove the second coded key

from the ignition.

5. Within twenty seconds of removing the second coded key, insert the

new unprogrammed key (new key) into the ignition and turn the ignition
from 1 (OFF/LOCK) to the 3 (ON) position (maintain ignition in 3 (ON)
for at least one second). This step will program your new key.

6. To program additional new unprogrammed key(s), wait at least 20

seconds and repeat this procedure from Step 1.
If successful, the new coded key(s) will start the vehicle’s engine and the

theft indicator will illuminate for three seconds and then go out.
If not successful, the new coded key(s) will not start the vehicle’s engine

and the theft indicator will flash on and off. You may repeat Steps 1
through 6. If failure repeats, bring your vehicle to your authorized dealer
to have the new spare key(s) programmed.

2

1

3

4

PERIMETER ALARM SYSTEM (IF EQUIPPED)

The perimeter anti-theft system will warn you in the event of an
unauthorized entry to your vehicle.

If there is any potential perimeter anti-theft problem with your vehicle,
ensure ALL remote entry transmitters are taken to the authorized
dealer to aid in troubleshooting.

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)

99

Locks and Security

Arming the system

When armed, the perimeter alarm will notify you of an unauthorized
entry. When unauthorized entry occurs, the system will flash the park
lamps and will sound the horn.

The system is ready to arm whenever the key is out of the ignition. Any
of the following actions will arm the alarm system:

• Press the remote transmitter lock control one time to arm the system.

• Lock all doors using the keypad.

• Lock all doors using the interior power lock switch while the driver or

passenger door is open and then closed.

If all the closures (doors, trunk, hood) are closed, the park lamps will
flash once and the horn will chirp once when the
entry transmitter is pressed a second time within five seconds.

If any closure is not properly closed, the park lamps will not flash and
the horn will chirp twice.

The system will wait 20 seconds after one of the arming actions is
performed before allowing the alarm to become armed. After the
20–second pre-arm phase, the interior trim remote trunk release control
and the power door unlock control are disabled, in order to further
protect your vehicle.

Disarming the system

You can disarm the system by any of the following actions:

• Unlock the doors by using the remote entry transmitter.

• Unlock the doors using a valid code on the keypad.

• Unlock the doors with the key in the key lock cylinder.

• Turn the ignition to the 3 (ON) position.

on the remote

100

2008 Crown Victoria (cro)
Owners Guide (post-2002-fmt)
USA (fus)