Follett SG1175S-48 Operators Manual

Single Door Upright Ice Storage

!

Bins with SmartGATE® Ice Shield

Order parts online
www.follettice.com

Welcome to Follett

Follett ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding
after-the-sale support. To ensure that this bin delivers that same degree of service, we ask that you take a moment to
review this instruction before beginning the installation of the bin. Should you have any questions or require technical
help at any point, please call our technical service group at [phone] (US & Canada) or [phone] and in
Poland: [phone].

Before you begin

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage
is found, notify the shipper immediately and contact Follett Corporation so that we can help in the ling of a claim, if
necessary.

Important cautions

§ Top is NOT fastened to bin.

§ Avoid excessive tightening force when connecting to the bin drain tting.

§ Do not apply excessive heat if any sweating of ttings is necessary. Heat conduction through
metal may melt threads in plastic drain tting.

§ When leveling, do not extend any leg more than 1 in. (26mm) for total leg height no greater than

2.125 in. (54mm).

§ SDU1000: Legs must be secured to oor through feet to avoid possible movement and resulting
injury.

Installation Instructions and Parts List

Installation

1. Remove all packing material from bin.

2. Remove all tape and temporary fastenings from door assemblies and outside of bin.

3. Remove top from bin.

4. Remove set of four legs and any other accessories packed inside bin.

5. Lay bin on back, being careful to protect nish, and remove bolts holding skid to bin.

6. Screw legs into tapped holes in bin bottom and tighten to seat legs well against bottom.

7. Set bin upright.

8. Reinstall top onto bin.

9. Remove protective paper from stainless steel exterior.

10. Move bin to permanent location.

11. Adjust “foot” at bottom of each leg to level bin in both directions.

12. Mount icemaker(s) on bin in accordance with icemaker manufacturer's instructions.

13. Connect drain line to 1" FPT female tting located in bottom of bin.

14. Make nal connections to icemaker.

Installing icemaker drain

(Required for some icemaker applications)

Some icemakers require a special drain system. For these machines Follett predrills the hole and provides the 3/4"
straight threaded drain tting to be installed through the hole. To install the tting:

1. Remove plastic nut on tting.

2. From inside bin (liner side), insert threaded portion through hole provided in side of bin.

3. Replace plastic nut on threaded portion and tighten against outside of bin.

4. Connect supplied tubing to icemaker drain connection after installing icemaker.

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]

www.follettice.com

EP 2138774

207890R05

Installing icemaker tie-downs (Fig. 1)

(Required for some icemaker applications)

Certain icemaker/bin combinations require installation of a tie-down
strap. If this tting has been included with your bin, proceed as follows:

Fig. 1

icemaker back

hole drilled

icemaker

1. Locate back of icemaker ush with back of bin.

2. Using center of vertical slot as a template, drill through icemaker wall
with 15/64 drill.

3. Fasten straps to icemaker and bin (bin holes are predrilled)
with #14 x 1/2 sheet metal screws and washers provided.

bin back

Removing lower door assembly

(Only if required for access through narrow doors)

1. With door in closed position, remove Phillips head screw and

washer from hinge area on each side of lower access door.

2. Insert screwdriver between door and hinge bracket on one side

of door and gently push against bracket to provide room for door
stud to clear bracket.

3. Remove access door.

4. Pull up on SmartGATE to remove.

5. Remove screws along top of door assembly.

6. Pull forward on top of assembly and lift to remove.

access door

15/64"

through

wall

tie-down

strap

Reinstalling door assembly

SmartG AT E

1. Reinstall lower door assembly in bin opening.

2. Reinstall screws in hood at top of door assembly.

lower door

assembly

3. Reinstall SmartGATE in side panel tracks and push down

to seat.

4. With door in closed position, insert one door stud through hinge

bracket, install washer, screw and tighten.

Note: For proper operation the access door must be reinstalled in

the closed position.

5. On other side, insert screwdriver between door and hinge bracket

and gently push against bracket to provide room for door stud to
clear bracket.

6. Reinstall washer and screw in lift door and tighten.

7. Check door to ensure proper operation.

Operation

SmartGATE operation

Follett’s unique SmartGATE positively controls the ow of ice into lower door assembly area for removal with either
a scoop or shovel. SmartGAT E can also be adjusted and locked at one of several levels to accommodate ow
characteristics of different types of ice.

Bin is shipped with SmartG AT E in full down position. SmartGAT E can be raised and locked in higher position for better
ow or when more access is needed.

If more ice is needed in lower door area:

1. Use full-length handle at top of SmartG AT E to gently lift and jiggle SmartGATE to encourage ice to ow into access

area of the bin (Fig. 2). (Loose ice will cascade into lower door area.)

2. When adequate ice has owed, push SmartGATE back down.

2