Follett MSL22SC Service Manual

Follett Maestro

™

Chewblet

®

400 Series

Icemaker and Top Kit

for Lancer countertop ice and beverage dispensers

Order parts online
www.follettice.com

Installation, Operation and Service Manual

4
6
2
8
0
2

F
S
N

U
L

R

C

U
L

R

Following installation, please forward this manual

to the appropriate operations person.

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
Fax [phone] • www.follettice.com

00117267R01

Table of contents

Welcome to Follett Corporation

Important cautions

Speci cations

Installation

Operation

Cleaning

Replacement Parts

Models MTL22SC, MSL22SC

Models MTL30SC, MSL30SC

3

3

4

7

15

15

17

17

18

Follett Corporation
Equipment Return Policy

Follett equipment may be returned for credit under the following conditions:

1. The equipment is new and unused.

2. A return authorization number has been issued by customer service within 30 days after shipment.

3. Follett receives the equipment at the factory in Easton, PA within 30 days after issuance of the return authorization number.

4. The equipment must be returned in Follett packaging. If the packaging has been damaged or discarded, Follett will forward, at the customer’s expense,
new packaging.

Note: Return freight charges are the responsibility of the customer. If equipment is returned and is damaged because of improper packaging,

Follett Corporation will not be held responsible.

Credit will be issued when:
The equipment has been inspected by Follett and deemed suitable to be returned to stock.

Note: A 15% restocking charge will be deducted from the credit. If the cost to return the product to stock exceeds 15%, the actual cost will be deducted.

2

Welcome to Follett

Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this equipment delivers that same degree of service, we
ask that you review the installation portion of this manual before beginning to install the unit. Our installation
instructions are designed to help you achieve a trouble-free installation. Should you have any questions or
require technical help at any point, please call our technical service group at [phone] or [phone].

Before you begin

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the  ling
of a claim, if necessary.

Check your paperwork to determine which model you have. Follett model numbers are designed to provide
information about the type and capacity of Follett equipment. Following is an explanation of the different model
numbers in the series.

MSL22SC

Icemaker configuration
SC = self-contained

Dispenser size
22 = 22" wide
24 = 24" wide
30 = 30" wide
44 = 44" wide

Dispenser manufacturer
C = Cornelius
L = Lancer
S = SerVend

Icemaker mounting
MT = Maestro top mount
MS = Maestro Satellite-fill™

Important cautions

!

Dispenser bin area contains mechanical, moving parts. Keep hands and arms clear of this
area at all times. If access to this area is required, power to unit must be disconnected  rst.

Follett recommends a Follett water  lter system (part# 00130229 for the 400 series) be
installed in the icemaker inlet water line.

Ice is slippery. Maintain counters and  oors around dispenser in a clean and ice-free condition.

Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.

3

Speci cations

Electrical

Model number Full load amps Max. fuse size

MC400 series icemaker 115/60/1 11.0 amps 20 amps

Ambient speci cations

Air temperature 100 F/38 C max. 50 F/10 C min. (best performance below 80 F/27 C)

Water temperature 90 F/32 C max. 40 F/4 C min. (best performance below 70 F/21 C)

Water pressure 70 P.S.I. max. (482kPA) 10 P.S.I min. (89kPA)

Plumbing

Your new icemaker is equipped with a drain line to simplify draining the evaporator and  oat reservoir. The tube
labeled “ oat/evap drain” is for SERVICE USE ONLY and must NOT be connected to the icemaker drain.

Water line sizes Make up water (inlet to  oat) 1/4" min.

Condenser (water-cooled only) 3/8" min.

Drain line sizes Icemaker drain 3/4" min.

Condenser (water-cooled only) 1/2" min.

Slope to drain 1/4" per foot (6mm per 30.4cm run) 1/2" min.

• Water shut-off recommended within 10 feet (3m), drain to be hard-piped and insulated

• Separate drains for icemaker and condenser. To prevent back  ow, do NOT connect drains.

• Follett recommends installation of a Follett water  lter system (part# 00130229) in icemaker inlet water line

Field Wiring: countertop and wall mount dispensers with Satellite- ll
icemakers

Consult enclosed D400A/W, R400A/W, MCD400A/W manual.

4

L

ULU

RR

NSF

Dimensions and clearances

Required clearances – MCD400 series

Entire front of icemaker clear of obstruction/connections to allow removal.

12" (305mm) above icemaker for service

6" (153mm) minimum between louvered (exhaust) side of icemaker and any adjacent equipment.

MCD400AHS – 18" (457mm) minimum, 10 ft (3m) maximum between discharge and air intake grilles.

Top back view — air-cooled

top mount

Front view — air-cooled

remote mount

1.875" (48mm)

13.00"

(331mm)

4.875"

(124mm)

2.375"

(61mm)

C

B

A

Side view — air-cooled

remote mount

22.75" (578mm)

20.75" (527mm)

C

F

B

A

12.875"

(327mm)

8.375"

(213mm)

4.75"

(121mm)

2.25"

(57mm)

17.00"

(432mm)

Front view — water-cooled

C

D

E

1.875" (48mm)

7.00" (178mm)

F

B

A

A – 3/4" MPT drain
B – 3/8" OD push-in water inlet
C – Electrical cord

6.875"

(175mm)

2"

(51mm)

Side view — water-cooled

20.75" (527mm)

17.00"

(432mm)

NSF

D – 3/8" FPT condenser inlet
E – 1/2" FPT condenser drain
F – Bin signal cord

5

Installation

1. Install Lancer ice dispenser according to manufacturer’s speci cations.

Note: We recommend that the dispenser back be mounted at least 1" (26mm) from wall to allow water, drain

and electric lines from top mount icemakers to be concealed behind dispenser.

2. Disconnect power to dispenser.

3. Remove front panel/merchandiser from the dispenser.

4. Adjust the agitation timer located on Lancer PC board to 1 second on (Fig. 1.1) – 2 1/2 hours off (Fig. 1.2).

Fig. 1

PRESS IN ON
THIS SIDE TO
TURN SWITCH
OFF.

SWITCH

OFF

ROCKER

SWITCHES

(VIEW LOOKING

DOWN)

OFF

SIDE VIEW

SIDE VIEW

1

2

3

4

5

6

7

8

PRESS IN ON
THIS SIDE TO
TURN SWITCH
ON.

SWITCH

ON

SWITCH

NUMBER

3
4

SWITCH

NUMBER

5
6
7
8

AGITATION TIME

1

4 SEC

ONDS

ECONDS

S

SECONDS

SECOND

2

3

OOOXXOX

X

1

AGITATION FREQUENCY

ON

TI

20 MINUTES

10 MINUTES

NO AGITA

O

O

O

O

O

O

X

O

O
X

O

O

UTES

UTES

IN

MIN

40

30 M

O

O

O

X

O

X

O

X

O

X

X

O

60 MIN

50 MINUTES

O

O

X

X
X

X

X

O

X = ON

O = OFF

TES

U

80 MINUTES

70 MINUTES

X

X

O

O

O

O

X

O

INUT

90 M

X
O
X
O

S

E

MINU

0

00 MINUTES

1

11

X

X

O

X

X

O

X

O

S

130

S

UTES

UTE

N

N

I

INUTES

MI

M

M

140

150

X

X

X

X

X

X

X

O

TES

NUTE

MI

20

1

X

X
O
X

2

6