Follett HCF1810RMS, HCD1810NMS, HCD2110NMS, HCF2110RMS Installation Manual
Horizon Elite™ Ice Machine Models with RIDE® Technology
Installation Instructions for Ice Manager™ Diverter Valve
HCD/HCF1810RMS, HCD/HCF2110RMS
HCD1810NMS, HCD2110NMS
(See model number congurator on page 2 for details.)
Order parts online
www.follettice.com
remote condensing
Ice Manager
Control Panel
Ice Manager
Diverter Valve
(1) Horizon
Chewblet® Ice Machine
(purchased separately)
™
(2) ice storage units
(purchased separately)
Any combination of bins or dispensers
Lane 2
Lane 1
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
01157924R01
Chewblet® Ice Machine Model Number Configurations
HC 1810D SVA
MC Maestro™
Chewblet
(425 Series)
HC Horizon
Chewblet
(710, 1010,
1410, 1810,
2110 Series)
HM Horizon
Micro Chewblet
C 208-230/60/1 (icemaking head)
®
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
425 up to
425 lbs
(193 kg)
710 up to
675 lbs
(306 kg)
1010 up to
1061 lbs
(482 kg)
1410 up to
1466 lbs
(665 kg)
1810 up to
1790 lbs
(812 kg)
2110 up to
2039 lbs
(925 kg)
CondenserSeriesVoltageIcemaker
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
P Cornelius Profile
PR150
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
2
remote condensing ICE MANAGER
Horizon ice machine for use with Ice Manager diverter valve system
The Ice Manager diverter valve system delivers ice to two ice storage units enabling a single Follett
Horizon ice machine to meet demand for ice at two locations. The system’s sensors monitor ice levels
in each storage unit and automatically switch ice delivery to the appropriate location.
After thorough review of Ice Manager site survey, read and complete
Horizon ice machine installation sections 1 through 6.
Unpack
1
Louvered docking assembly
3
External connection
5
Site preparation
2
Ice transport tube
4
Internal connection
6
Front cover
7
For connection to Ice Manager diverter valve system
refer to Ice Manager installation guide.
ICE MANAGER remote condensing
3
Carefully unpack and inspect the contents of your Follett ice machine.
Unpack
1
1. 1
Unpack ice machine
➊
➍
➋
7/16"
➌
➎
DO NOT TILT ICE MACHINE
TO ACCESS BOLTS!
7/16"
➏
4
COMPRESSOR DAMAGE
WILL RESULT
➐
remote condensing ICE MANAGER
Site preparation
1" PVC Drain
2 ft. x 1" OD
silicone tubing
3/4" MPT x 1" slip
3/4" barb x 3/4" FPT
➌
1'
➌
1/4" per foot
(6,4 mm per 0,3 m)
Prepare the installation site.
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
2
2.1
2.1
Installation site requirements
➋
➋
➊
NEMA
5-15
3/8" ∅ (9,5mm)
➎
7/8" ∅ (22,4mm)
➍
Electrical ➊
Potable water supply
Drain
• Minimum 8” radius on silicone drain line. Drain line from the ice machine must have at least
Refrigeration lines
• 7/8” ∅ (22,4 mm) suction line 1810/2110(insulated)
ICE MANAGER remote condensing
• 120/60/1-5 amps
(3/8” push-in internal connection, 3/8” OD tubing required)
➋
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
• This equipment is to be installed with adequate backow protection to comply with applicable
federal, state, and local codes
(3/4” Barb)
➌
1/4” per foot pitch (6,4mm/0,3m).
➍
• 3/8” ∅ (9,5 mm) liquid line
➎
➍
5
Loading...