Follett HCD1810NJS, HCD2110NJS, HCF2110RJS, HCF1810RJS Installation Manual
Horizon Elite™ Ice Machine Models with RIDE® Technology
HCD/HMD/HCF/HMF1810RJS, HCD/HMD/HCF/HMF2110RJS,
HCD/HMD1810NJS, HCD/HMD2110NJS
(See model number congurator on page 2 for details.)
Order parts online
www.follettice.com
Installation Instructions for Drop-Ins
remote condensing
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
01157890R01
Chewblet® Ice Machine Model Number Configurations
HC 1810D SVA
CondenserSeriesVoltageIcemaker
MC Maestro™
Chewblet
(425 Series)
HC Horizon
Chewblet
(710, 1010,
1410, 1810,
2110 Series)
HM Horizon
Micro Chewblet
C 208-230/60/1 (icemaking head)
®
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
425 up to
425 lbs
(193 kg)
710 up to
675 lbs
(306 kg)
1010 up to
1061 lbs
(482 kg)
1410 up to
1466 lbs
(665 kg)
1810 up to
1790 lbs
(812 kg)
2110 up to
2039 lbs
(925 kg)
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
P Cornelius Profile
PR150
S RIDE™
T Top-mount
CAUTION!
§ This appliance should be connected by a qualied person in accordance with applicable codes.
§ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
§ Connect to potable water supply only.
§ This appliance can be used by children aged 8 years and above and persons with reduced physical,
sensory, or mental capabilities, or lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
should be supervised to ensure that they do not play with the appliance.
§ This appliance is intended to be used for household and similar applications such as staff kitchen areas
in shops, offices and other working environments; farm houses and by clients in hotels, motels and other
residential type environments; bed and breakfast type environments; catering and similar non-retail
applications.
§ WARNING! To avoid a hazard due to instability of the appliance, it must be xed in accordance with the
instructions.
ConfigurationApplication
(RIDE remote
ice delivery
equipment)
2
remote condensing DROP-IN • RIDE Technology
Read and complete the following 8 installation steps
Unpack
1
Dispenser preparation
3
Ice transport tube
5
Site preparation
2
Louvered docking assembly
4
External connection
6
Internal connection
7
Front cover
8
DROP-IN • RIDE Technology remote condensing
3
Carefully unpack and inspect the contents of your Follett ice machine.
Unpack
1
1. 1
Unpack ice machine
➊
➍
➋
7/16"
➌
➎
DO NOT TILT ICE MACHINE
TO ACCESS BOLTS!
7/16"
➏
4
COMPRESSOR DAMAGE
WILL RESULT
➐
remote condensing DROP-IN • RIDE Technology
➌
Site preparation
Prepare the installation site.
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation of
low side is not recommended and will void warranty.
2
2.1
2.1
Installation site requirements
7/8" ∅ (22,4mm)
➍
➊
NEMA
5-15
3/8" ∅ (9,5mm)
➎
➋
2 ft. x 1" OD
silicone tubing
and ttings
provided
1/4" per foot
(6,4 mm per 0,3 m)
Electrical
• 120/60/1-5 amps
Potable water supply
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
• This equipment is to be installed with adequate backow protection to comply with applicable
federal, state, and local codes
Drain
• Minimum 8” radius on silicone drain line. Drain line from the ice machine must have at least
1/4" per foot pitch (6,4mm/0,3m).
Refrigeration lines
• 7/8" ∅ (22,4 mm) diameter suction line (insulated)
• 3/8" ∅ (9,5 mm) liquid line
➊
(3/4” Barb)
➌
(3/8" push-in internal connection, 3/8" OD tubing required)
➋
➍
➍
➎
DROP-IN • RIDE Technology remote condensing
5
Loading...