Follett HCF1410RMS, HCD1010NMS, HCF1010RMS, HCD1410NMS Installation Manual
Horizon Elite™ Ice Machine Models with RIDE® Technology
Installation Instructions for Ice Manager™ Diverter Valve
HCD/HCF1010RMS, HCD/HCF1410RMS,
HCD1010NMS, HCD1410NMS
(See model number congurator on page 2 for details.)
Order parts online
www.follettice.com
remote condensing
Ice Manager
Control Panel
Ice Manager
Diverter Valve
(1) Horizon
Chewblet® Ice Machine
(purchased separately)
™
(2) ice storage units
(purchased separately)
Any combination of bins or dispensers
Lane 2
Lane 1
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
01113372R00
HC 1400C SVA
Chewblet® Ice Machine Model Number Configurations
MC Maestro™
Chewblet
(400 Series)
HC Horizon
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro Chewblet
C 208-230/60/1 (icemaking head)
®
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
400 up to
454 lbs
(206kg)
1000/1010
up to
1036 lbs
(471kg)
1400/1410
up to
1450 lbs
(658kg)
1650 up to
1580 lbs
(717kg)
CondenserSeriesVoltageIcemaker
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
2
remote condensing ICE MANAGER
Horizon ice machine for use with Ice Manager diverter valve system
The Ice Manager diverter valve system delivers ice to two ice storage units enabling a single Follett
Horizon ice machine to meet demand for ice at two locations. The system’s sensors monitor ice levels
in each storage unit and automatically switch ice delivery to the appropriate location.
After thorough review of Ice Manager site survey, read and complete
Horizon ice machine installation sections 1 through 6.
Unpack
1
Louvered docking assembly
3
External connection
5
Site preparation
2
Ice transport tube
4
Internal connection
6
Front cover
7
For connection to Ice Manager diverter valve system
refer to Ice Manager installation guide.
ICE MANAGER remote condensing
3
Carefully unpack and inspect the contents of your Follett ice machine.
Unpack
1
1. 1
Unpack ice machine
➊ ➋
➌
7/16"
➍
7/16"
➎ ➏
4
remote condensing ICE MANAGER
Site preparation
Prepare the installation site.
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
2
2.1
2.1
Installation site requirements
1/4" per foot
(6,4 mm per 0,3 m)
➊
NEMA
5-15
➋
3/8" ∅ (9,5mm)
➎
5/8" ∅ (15,8 mm)
➍
➋
➌
1'
Electrical ➊
• 120/60/1-5 amps
Potable water supply
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
• This equipment is to be installed with adequate backow protection to comply with applicable
federal, state, and local codes
Drain
Refrigeration lines
• 5/8” ∅ (15,8 mm) diameter suction line (insulated)
(3/4” MPT)
➌
• The drain line from the ice machine must have at least 1/4” per foot pitch (6,4 mm/0,3 m)
• 3/8” ∅ (9,5 mm) liquid line
(3/8” push-in internal connection, 3/8” OD tubing required)
➋
➍
➍
➎
ICE MANAGER remote condensing
5
Loading...