Follett HCC1010WPS, HCD710APS, HCC1410WPS Installation Manual

Horizon Elite™ Ice Machine Models with RIDE™ Technology

Installation Instructions for Cornelius PR150

HCD710APS, HCC1010APS, HCC1410APS, HCC1010WPS, HCC1410WPS,

(See model number congurator on page 2 for details.)

Order parts online
www.follettice.com

self-contained

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

01113265R02

Chewblet® Ice Machine Model Number Configurations

HC 1810D SVA

MC Maestro™

Chewblet
(425 Series)

HC Horizon

Chewblet
(710, 1010,
1410, 1810,
2110 Series)

HM Horizon

Micro Chewblet

C 208-230/60/1 (icemaking head)

®

Self-contained only.

D 115/60/1 (icemaking head)

Self-contained and remote. If remote
unit, high side is 208-230/60/1.

E 230/50/1 (icemaking head)

Self-contained only.

F 115/60/1 (icemaking head)

Remote only. High side is
208-230/60/3.

425 up to

425 lbs
(193 kg)

710 up to

675 lbs
(306 kg)

1010 up to

1061 lbs
(482 kg)

1410 up to

1466 lbs
(665 kg)

1810 up to

1790 lbs
(812 kg)

2110 up to

2039 lbs
(925 kg)

CondenserSeriesVoltageIcemaker

A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for

connection to parallel rack system

V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager

diverter valve
system

P Cornelius Profile

PR150

ConfigurationApplication

S RIDE™

(RIDE remote
ice delivery
equipment)

T Top-mount

2

self-contained Cornelius • RIDE Technology

Read and complete the following 8 installation steps

Unpack

1

Dispenser preparation

3

Ice transport tube

5

Site preparation

2

Louvered docking assembly

4

External connection

6

Internal connection

7

Front cover

8

Cornelius • RIDE Technology self-contained

3

Carefully unpack and inspect the contents of your Follett ice machine.

Unpack

1

1. 1

Unpack ice machine

➊

➍

➋

7/16"

➌

➎

DO NOT TILT ICE MACHINE
TO ACCESS BOLTS!

7/16"

➏

4

COMPRESSOR DAMAGE
WILL RESULT

➐

self-contained Cornelius • RIDE Technology

Site preparation

Prepare the installation site.

Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.

2

2.1

2.1

Installation site requirements

H_C1010A/W

NEMA

6-15

HCD710A

NEMA

5-15

H_C1410A/W

NEMA

6-20

➊

➋

2 ft. x 1" OD
silicone tubing
and ttings
provided

➌

➍

Electrical ➊

• H_C1010/1410(A/W)JS 208-230/60/1-15A • HCD710APS 115/60/1-15A

Potable water supply

• 10-70 psi (69-483kpa)

• 45 to 90 F (7 to 32 C)

• Follett recommends the use of an in-line water ltration system (item# 00130286)

• This equipment is to be installed with adequate backow protection to comply with applicable
federal, state, and local codes

Condenser water supply for water-cooled systems

• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)

• 45 to 90 F (7 to 32 C)

• 1.5 gallons per minute (5.68 liters per minute)

Drain

(3/4" Barb)

➍

• The drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m)

(3/8" push-in internal connection, 3/8" OD tubing required)

➋

(1/4" FPT inlet, 1/4" FPT outlet)

➌

1/4" per foot
(6,4 mm per 0,3 m)

1'

Cornelius • RIDE Technology self-contained

5

Prepare the dispenser.

Dispenser preparation

3

3.1

➋

➋

• Remove ice entry cover plate

• Remove bin thermostat capillary tube from

bracket

➋

➊

➊

3.2

➊

• Coil capillary tube and secure away from bin

ll opening

➊

3.3

• Remove retaining clips

➋

6

➊

➋

and deector nuts

➊

3.4

➊

➋

• Remove capillary tube bracket

deector (Fig. 4.2) from inside ice storage
hopper

self-contained Cornelius • RIDE Technology

➋

➊

and