Follett 102552, 65044, 42530, 30022, 95048 User Manual

Slope Front

Ice Storage Bins

Order parts online (US only)
www.follettice.com

Installation and Parts Manual

Following installation, please forward this manual

to the appropriate operations person.

Follett Corporation
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

Follett Europe Polska
Mokry Dwór 26C • 83-021 Wislina, Poland
[phone] • Fax [phone]
www.folletteurope.com

205448R04

Welcome to Follett

Follett ® ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this slope front bin delivers the same degree of service, we ask
that you take a moment to review this manual before beginning the installation of the bin. Should you have any
questions or require technical help at any point, please call our technical service group, [phone] (US
and Canada only) or [phone] (Worldwide) or [phone] (Europe and Middle East only).

Before you begin

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the  ling of
a claim, if necessary.

Important cautions

Avoid excessive tightening force when connecting to the bin drain  tting.

Do not apply excessive heat if any sweating of  ttings is necessary. Heat conduction through metal may

melt threads in plastic drain  tting.

2

Installation

catch assem

lift door

front of icemaker

Fig. 1

1. Remove all packing material from bin.

2. Remove all tape and temporary fastenings from door and outside of bin.

3. Remove set of four legs and any other accessories packed inside bin.

4. Lay bin on its back, being careful to protect  nish, and remove bolts holding
skid to bin.

5. Screw legs into tapped holes in bin bottom and tighten to seat legs well
against bottom.

6. Set bin upright and move to permanent location.

7. Remove protective paper from stainless steel surfaces.

8. Adjust “foot” at bottom of each leg to level bin in both directions.

9. Mount icemaker(s) on bin in accordance with icemaker manufacturer’s
instructions.

10. Connect drain line to 1" IPS female  tting located in bottom of bin.

11. Make  nal connections to icemaker.

Lift door catches (Fig. 1)

1. Position lift door in upright position.

2. Center catch on icemaker front above door and position catch to securely

hold door when open.

3. Drill two (2) 7/64 (2.78 mm) holes through catch holes and into icemaker

Fig. 2

face.

4. Install catch using two (2) #6-1/2 sheet metal screws supplied.

icemaker back

Icemaker tie-downs (Fig. 2)

(Required for some icemaker applications only)
Certain icemaker/bin combinations require the installation of a tie-down strap.

If straps have been included with your bin, proceed as follows:

1. Locate icemaker back  ush with bin back.

2. Using center of vertical slot as a template, drill through icemaker wall with

a 15/64" (5.95 mm) drill.

3. Fasten straps to icemaker and bin (bin holes are predrilled) with

#14 x 1/2 sheet metal screws and washers provided

Icemaker drain

(Required for some icemaker applications only)
Some machines require a special drain system. For these machines Follett

predrills the hole and provides a 3/4" straight threaded drain  tting to be installed
through the hole. To install the  tting:

1. Remove plastic nut on  tting.

2. From inside bin (liner side), insert threaded portion through hole provided in side of bin.

3. Replace plastic nut on threaded portion and tighten against outside of bin.

4. Connect supplied tubing to icemaker drain connection after installing icemaker.

bin back

15/64"
(5.95 mm)
hole drilled
through
icemaker
wall

tie-down
strap

Cleaning and sanitizing

Interior bin cleaning

Follett slope front ice storage bins are equipped with polyethylene liner walls and stainless steel bottoms that
should be cleaned and sanitized prior to use and periodically with any cleaning and sanitizing products suitable
for use in a food zone.

Important: Follett Corporation recommends installing a properly-sized, activated carbon (charcoal) water  lter on

water supply to icemaker to remove chlorine.

Exterior bin cleaning

Exterior stainless steel surfaces can be cleaned with a stainless steel cleaner such as 3M* Stainless Steel
Cleaner & Polish or equivalent.

* 3M is a registered trademark of 3M Company in the US and other countries.

3

Replacement parts

lift door

foaming plug

pivot hinge

Front View

Lift doors

Door hardware

Gaskets

Miscellaneous

gasketing

Front View (inside surface)

Foamed Lift Door

Front View

Hinge

pivot pin

Side View

Hinge

Side View

Catch and Door

Description Part #

Lift door, 21.25" (540 mm) x 15" (381 mm), for 22" (559 mm) wide bins
(includes pivot hinges and pins)

Lift door, 29.25" (743 mm) x 15" (381 mm), for 30" (762 mm) wide bins
(includes pivot hinges and pins)

Lift door, 42" (1067 mm) x 16" (406 mm), for 42.8" (1087 mm) wide bins
(includes pivot hinges and pins) — Europe only

Lift door, 43.25" (1099 mm) x 15" (381 mm), for 44" (1118 mm) wide bins
(includes pivot hinges and pins)

Lift door, 47.25" (1200 mm) x 15" (381 mm), for 48" (1219 mm) wide bins
(includes pivot hinges and pins)

Lift door, 51.25" (1302 mm) x 15" (381 mm), for 52" (1321 mm) wide bins
(includes pivot hinges and pins)

Catch, for lift doors when icemaker is  ush with bin front 500083
Catch, for lift doors when icemaker is set back from bin front 500984
Hinges, pivot (2), door mount, for all foamed lift doors 501157
Pins, pivot (2), for all lift doors 500343

Gasket, for 22" (559 mm) wide bins with poly backed lift doors 00989426
Gasket, for 30" (762 mm) wide bins with poly backed lift doors 501871
Gasket, for 42.8" (1087 mm) wide bins with poly backed lift doors — Europe only 00990879
Gasket, for 44" (1118 mm) wide bins with poly backed lift doors 501872
Gasket, for 48" (1219 mm) wide bins with poly backed lift doors 501873
Gasket, for 52" (1321 mm) wide bins with poly backed lift doors 501874
Gasket, plastic edge extrusion, for ice drop hole in top of bin 500785

Drain assembly, plastic 500977
Drain  tting, blow down 501652
Lock nut, drain, blow down 501653
Tubing, drain, blow down 501654
Drain assembly, blow down (includes 501652, 501653, 501654) 501655
Legs (set of 4), 6" (153 mm) adjustable to 7.5" (191 mm), plastic 500089
Legs (set of 4), 6" (153 mm) adjustable to 7.5", (191 mm) stainless 500272
Legs (set of 4), 6" (153 mm) adjustable to 7.5" (191 mm), stainless, with  anged feet 501300
Legs (set of 4), 12" (305 mm) adjustable to 13.5" (343 mm), die cast zinc 500645
Shovel, plastic 501796
Bracket, shovel 502360
Scoop, ice, San Jamar 00146365
Sealant, RTV, 5 oz tube 500727

00989418

501153

00990853

501154

501299

501155

Follett is a registered trademark of Follett Corporation, registered in the US.

Follett Corporation
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

Follett Europe Polska

4

Mokry Dwór 26C • 83-021 Wislina, Poland
[phone] • Fax [phone]
www.folletteurope.com

205448R04

8/12