Flymo GCT24A Original Instructions Manual

®

IMPORTANT INFORMATION

Read before use

& retain for future reference

Sabre Trim

Original Instructions

Carton Contents

IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new product.
IF ANY PARTS ARE MISSING CONTACT:

­Husqvarna UK Ltd. Customer Service Department direct
Telephone : [phone] UK 1800 882 350 ROI Fax : [phone]

Safety

WARNING. When using the product the safety rules must be followed. For your own safety and that of by­standers please read these instructions before operating the product. Please keep the instructions safe for later
use.

Explanation of Symbols on your product

Warning

Read the user instructions carefully to
make sure you understand all the controls
and what they do.

Keep others, including children, pets and
bystanders outside the 10 metre hazard
zone. Stop the trimmer immediately if you
are approached.

The use of eye protection is recommended
to protect against objects thrown by the
nylon line.

To avoid the possibility of electric shock,
do not use in damp or wet conditions.

Switch off! Remove plug from battery
pack before adjusting, cleaning or if
cable is damaged.

Warning The cutting line continues to rotate after the
machine has been switched off.

360º

10m

steady handle

guard

instruction

manual

wheel

trimmer

head

Trimmer Head
storage holder

screws x 4

steady handle

storage holder

screws x 2

General

1. This product is not intended for use by persons

(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning the use of the product by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with the
product. Local regulations may restrict the age of the
operator.

2. Never allow children or people unfamiliar with the

instructions to use the machine.

3. Stop using the machine while people, especially

children, or pets are nearby.

4. Only use the product in the manner and for the

functions described in these instructions.

5. Never operate the product when you are tired, ill or

under the influence of alcohol, drugs or medicine.

6. The operator or user is responsible for accidents or

hazards occurring to other people or their property.

7. Keep bystanders away. Do not operate whilst people,

especially children or pets are in the area.

Battery
Cordless Battery Powered Products require special care.

1. AVOID ACCIDENTAL STARTING - KEEP HANDS
AND FINGERS AWAY FROM THE SWITCH LEVER
WHILE CARRYING THE PRODUCT.

2. Do not attempt to repair the unit including the battery.
Nylon line replacement and cleaning the unit are the
only items suitable for user maintenance.

3. Do not insert any object into the motor area.
Keep free of debris to avoid overheating.

Preparation

1. While using your product always wear substantial
footwear and long trousers.

2. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.

3. Inspect the area to be cut before each use. Remove
all objects such as stones, broken glass, nails, wire,
string etc, which can be thrown or become entangled
in the trimmer head.

4. Before use, inspect the area for wildlife, especially
hedgehogs.

5. Check that the cutting head, spool and cap are
fitted correctly.

Use

1. Use the trimmer only in daylight or good artificial light.

2. Avoid operating your trimmer in wet grass, where
feasible.

3. Take care in wet grass, you may lose your footing.

4. On slopes, be extra careful of your footing and
wear non-slip footwear.

5. Do not walk backwards when trimming, you could
trip. Walk, never run.

6. Switch off before pushing the trimmer over
surfaces other than grass.

7. Never operate the trimmer with damaged guards
or without guards in place.

8. Never fit metal cutting elements.

9. Keep hands and feet away from the cutting means at all
times and especially when switching on the motor.

10. Keep cutting head below waist level.

11 . Do not lean over the trimmer guard whilst trimming or

edging - objects may be thrown by the cutting line.

12. Beware of cut-off pieces of nylon line ejected
during use.

13. If you hit an object, do not use your trimmer until
you are sure that the entire trimmer is in a safe

operating condition.

14. If the trimmer starts to vibrate abnormally, check
immediately. Excessive vibration can cause injury.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure
the trimmer is in safe working condition.

2. Replace worn or damaged parts for safety.

3. Only use the replacement cutting line specified
for this product.

4. Only use replacement parts and accessories
recommended by Husqvarna UK Ltd..

5. To avoid the risk of injury keep fingers and hands
clear of the line cutter on the leading edge of the
guard.

6. Clean unit with a dry cloth. Never use metal
objects to clean the unit.

7. Inspect and maintain the trimmer regularly. Any repairs
must be carried out by an authorised repairer.

8. Store in a cool dry place and out of reach of
children. Do not store outdoors.

9. Allow the product to cool for atleast 30 minutes
before storing.

Assembly Instructions

Safety Guard Assembly (A) & (B)

1. Locate the safety guard (B1) over the cutting head
(A2). Ensure the nylon line is fed through the hole in
the safety guard as illustrated in fig A.

2. Push into location and turn safety guard in the direc­tion illustrated in Fig B, until a click is heard and the
safety guard is securely locked in position.

• ENSURE THE SAFETY GUARD IS SECURELY IN
PLACE BY ATTEMPTING TO TWIST GUARD.

Wheel Assembly (C) & (D)

1. Fix the 2 halves of the wheel together as illustrated
in fig C.

2. Attach the wheel to the trimmer making sure that it is lo­cated into the groove on the trimmer head (D1).

3. Clip the wheel together on the other side, making
sure it is secure.

4. The wheel should turn freely.

B

A

C D

1

2

1

Attatching the Trimmer Head to the Sabre Handle

1. Push the Trimmer Head onto the Sabre Handle until you hear a click. (E1)

2. Push the Trimmer Head further onto the Sabre Handle until it reaches the mark shown in Fig E2.

3. Turn the Trimmer Head collar until it is secure. (E3)

E2

E1 E3