Fluke Ti30 User Manual

Low cost of ownership for a fully radiometric imager

Fluke Ti30 Thermal Imager Speciﬁcations

The Fluke Ti30 Thermal Imager provides low total cost of ownership for a full-featured, radiometric imager. The package includes all hardware, software and training required without any additional costs. Standard calibration and service rates for the Ti30 imager are also extremely competitive for the industry.

To understand your full investment in a thermography program, here are some questions to consider:

Product and performance

• Is the camera you are purchasing fully

radiometric (i.e. measures temperature on every one of the available pixels)?

– The ability to measure absolute

temperature is critically important to establishing an effective predictive maintenance program for electrical and mechanical equipment.

Software

• Is there an additional cost for

professional reporting software?

• Is there a licensing fee for each

additional user or desktop?

Training and ease of use

• Is training offered at no additional cost?

• Is the camera easy to use?

• Will your electricians and/or mechanics,

with only some basic training, be able to use the camera as a tool to help them do their job better?

Re-calibration, service and repair

• How much does it cost to send the

camera in for calibration?

• How much do basic repairs cost?

• How likely is it that the lens will

be scratched?

Detector

Detector Type: 120 x 160 uncooled focal plane array NETD (Thermal Sensitivity): 200 mK

Thermal

Temperature Range: -10 to 250 °C (14 to 482 °F) Accuracy: ±2 % or ±2 ºC (±3 % or 3 °C from -10 to 0 °C)

Optical

Optical Resolution: 90:1 Slit Response Optical Resolution: 225:1 Minimum Diameter Measurement Spot: 7 mm (0.27 in) at 61 cm (24 in) Field of View (FOV): 17 º Horizontal x 12.8 º Vertical Target Sighting: Single laser (Meets IEC Class 2 & FDA Class II requirements)

Controls and Adjustments

Focus: Focusable, 61cm (24 in) to inﬁnity Temperature Scale: ºC or ºF selectable Palettes: Gray, Ironbow or Rainbow Measurement Modes: Automatic, Semi-Automatic or Manual LCD Backlight: Bright, Dim, Off-Selectable Adjustable Emissivity: 0.10 to 1.00 by 0.01 Reﬂected Background Temperature: -50 to 460 ºC (-58 to 860 ºF)

Environmental

Ambient Operating Temperature: -10 to 50 ºC (14 to 122 ºF) Relative Humidity: 10 to 90 % Non-Condensing Storage Temperature: -25 to 70 ºC (-13 to158 ºF) [without batteries]

Other

Storage Capacity: 100 images Power: Rechargeable battery pack or 6 AAs (not included) Battery Life: Minimum 5 hours continuous use Image Frame Rate: 20 Hz Thermal Analysis Software: InsideIR (included) PC Software Operating Systems: Microsoft Weight (includes batteries): 1 kg (2.2 lb) Warranty: 1 year (U.S. only)

Windows® 2000® or XP

Ordering information

The Fluke Ti30 Thermal Imager is sold exclusively through authorized thermography distributors. To request a demonstration or order a Ti30 imager, visit

www.ﬂuke.com/thermography

or call (800) 443-5853.

• Docking Station with Universal

Power Adapter and USB Connection

• Hardshell Carrying Case

• USB Field Cable

• Rechargeable Battery Pack

• AA Battery Pack (batteries not included)

• Interactive CD with InsideIR Software

and User Manual

• Training Presentation CD

• Carrying Pouch

• Wrist Strap

• Sun Visor

• Quick Reference Card

• One Seat in Professional Training Course

Additional batteries, chargers or replacements

• How does the battery recharging

time compare to the battery discharging time?

• How many batteries and charging

stations are needed to get through a full day of inspections?

Fluke. Keeping your world

up and running.

Fluke Corporation

PO Box 9090, Everett, WA USA 98206

Fluke Europe B.V. PO Box 1186, 5602 BD Eindhoven, The Netherlands

For more information call: In the U.S.A. (800) 443-5853 or Fax (425) 446-5116 In Europe/M-East/Africa (31 40) 2 675 200 or Fax (31 40) 2 675 222 In Canada (800) 36-FLUKE or Fax (905) 890-6866 From other countries +1 (425) 446-5500 or Fax +1 (425) 446-5116 Web access: http://www.ﬂuke.com/thermography

• Complete imaging solution

• Low cost of ownership

• Designed for predictive maintenance

Fluke Ti30™ Thermal Imager

Everything needed for everyday imaging.

Fluke Ti30 Thermal Imager

Unbeatable solution for infrared predictive maintenance.

Inspection routes improve maintenance performance.

Both preventive and predictive maintenance programs rely on periodic inspections of critical plant assets. To optimize a program’s success, maintenance personnel develop inspection routes by determining the frequency, sequence and physical course for equipment needing inspection.

The Fluke Ti30 Thermal Imager uniquely supports thermography inspection routing. After the ﬁrst inspection, the images taken can be combined in the InsideIR with location names and temperature data, and uploaded to the imager for use as a routing guide.

During subsequent inspections, an on-camera display prompts the user exactly where to take images— improving accuracy. The new images are easily compared to previous scans, helping to identify potential problems before they cause failure.

™

software

Expand your predictive maintenance program.

Obtain high-quality thermal images with a simple “click” of the trigger.

Download images and data into the companion InsideIR software for analysis and reporting.

Assign a unique name, preset emissivity and RTC values, assign alarm limits and add meaningful comments to each measurement location.

Easy to learn and easy to use.

• Single-level menus make set-up easy, without

the complicated multi-layer decisions other imagers require.

• Gain and level controls can be set to “automatic”

or changed manually for maximum ﬂexibility.

• Squeeze trigger once to freeze an image—

then choose whether to store it or discard without saving.

• Direct access switches for laser, temperature

scale, palette, backlight and measurement modes means changing takes only a second.

InsideIR software: Powerful and ﬂexible.

The Fluke Ti30 Thermal Imager allows maintenance personnel to quickly and easily capture high-quality infrared images. Because the camera collects 12 bits of information for every one of its 19,200 pixels, users in the ﬁeld can simply point, focus and shoot. With a properly composed, well-focused image, all further analysis can be performed with the InsideIR software in the quiet, comfort and safety of an ofﬁce.

Designed for the industrial maintenance environment.

The Ti30 thermal imager enables infrared inspections all day—every day. The camera’s 5+ hour battery life, and 100-image storage capacity, are more than enough for an entire shift of uninterrupted inspections. Other systems would require three batteries, multiple chargers, and/or additional memory devices for similar performance.

With the rugged Ti30 thermal imager, maintenance organizations can conduct thermographic inspec tions anytime, anywhere, and identify potential equipment problems before they cause failure. Use the Ti30 imager regularly—not just in a crisis or for an annual maintenance check.

In the imager during the scan, or later in the InsideIR software, adjust:

• Palette settings

• Emissivity

• Reﬂected temperature correction values

• Level and gain

This approach provides ﬂexibility and eliminates the need to re-scan equipment if different settings are desired once the user is back in the ofﬁce. The ﬁle of images and data can also be e-mailed to other Ti30 imager-InsideIR software users, making information sharing and cross-checking easy.

Includes professional thermography training course* to accelerate return on investment.

• Practical, hands-on course designed to

shorten the learning curve for new

Fluke Ti30 Thermal Imager owners covers: – Infrared and thermography theory – Primary applications for electrical and

mechanical systems

• Taught by certiﬁed thermography

professionals.

In U.S. and Canada. Training program varies by country.

Travel expenses not included.

The Fluke Ti30 Thermal Imager enables plant thermography specialists to manage a much larger infrared predictive maintenance program—and delegate inspection routing responsibilities to appropriate personnel, such as electricians and mechanics, who specialize in the equipment being inspected. This frees the trained expert to handle program management, image analysis and interpretation, and report generation.

Best complete thermography solution

Inspections can now be delegated to electricians and mechanics, those most familiar with the equipment. They simply follow the on-camera, step by step routing instructions, point, focus and shoot.

Versatile solution for plant maintenance professionals.

• High performance features for the expert, packaged in an easy

to use device for beginners.

• Adjust key image parameters (emissivity, RTC, temperature level

and gain) in the ﬁeld on the camera, or back at the ofﬁce on the PC.

• Large, clear LCD display works well both indoors and outside.

• Use the docking station for USB communications in the ofﬁce,

or the USB ﬁeld cable when working remotely.

• Use the rechargeable battery pack or the standard AA pack.

Capture clear thermal images and easily analyze the radiometric (temperature) data for all 19,200 pixels.

Analyze individual images, easily identify hot (or cold) spots and select areas for min., max. and avg. temperature values.

Quickly and easily create professional reports using InsideIR software.