Fluke 2063513, MULTIMETER WITH TEMPERATURE 16, 16 Instruction Sheet

16

®

Multimeter with Temperature

Instruction Sheet

P

To ensure that the meter is used safely, follow these instructions:

• Do not use the meter if the meter or test leads appear damaged, or if

• Disconnect the live test lead before disconnecting the common test

• When using the probes, keep your fingers behind the finger guards on

• Do not use the V•Check

Read First: Safety Information

you suspect that the meter is not operating properly.

lead.

the probes.

mode to measure voltages in circuits that

could be damaged by this mode's low input impedance
(≅2 kΩ).

• Turn off power to the circuit under test before cutting, desoldering, or

breaking the circuit. Small amounts of current can be dangerous.

• Do not apply more than 600V rms between a meter terminal and earth

ground.

• Use caution when working with voltages above 60V dc or 30V ac rms.

Such voltages pose a shock hazard.

PN 2063513 December 2002 Rev.1, 9/04

2002,2004 Fluke Corporation. All rights reserved. Printed in China

Symbols

Press button.

Press button to switch between modes.

Double insulation.

Manual ranging mode.
ip14i.eps

Automatic Range Selection

The meter defaults to autoranging when you turn it on. The 4000 mV
range can be entered only with manual range selection.

Manual Range Selection

MULTIMETER

16

To return to autoranging, press for

OFF

CAT

600V

COM

+

2 seconds, or change the measurement
mode.

ip15i.eps

Battery Saver

If the meter is ON but inactive and not connected to voltage for more than
45 minutes, the display goes blank to preserve battery life. To resume
operation, press any button.

Battery Saver is disabled in MIN/MAX record mode.

AC and DC Voltage

Also refer to V•Check.
Volts AC Volts DC

Input Impedance ≅5 MΩ Input Impedance ≅10 MΩ
50 Hz to 400 Hz

MULTIMETER

16

DCAC

4000 mV 4V 40V 400V 600V

OFF

V

AC / DC

CAT

600V

COM

+

Resistance and Continuity

eR

OFF

Turn off circuit power before testing. Also refer to V•Check.

MULTIMETER

16

V

AC / DC

CAT

600V

COM

+

ip01i.eps

Resistance

MULTIMETER

16

Continuity

Mk

OFF

COM

Detects shorts and opens ≥250 µS.

V¥Check

A

CAT

TEMPERATURE

600V

+

Low Impedance

V¥Check

MULTIMETER

16

OFF

COM

V¥Check

A

CAT

TEMPERATURE

600V

+

OFF

COM

Short Open

<25Ω

MULTIMETER

16

CAT

600V

TEMPERATURE

+

V¥Check

A

ip02i.eps

W

V•Check

If a dc or ac voltage greater than about 4.5V is present across the inputs
when the meter is set to

R, G, or e, the meter switches automatically

to dc or ac voltage mode (V•Check mode).

W Warning

Repetitive transients on a dc bus will cause V•Check to
select ac volts, even though a hazardous dc voltage may
be present. To avoid a misleading display and possible
electric shock, manually select the proper volts function
for measurements on these circuits.

When V•Check is activated, the meter has low input impedance (LoZ)
≅2 kΩ. This load can alter the voltages in electronic control circuits. Do

not use V•Check to measure voltage in circuits that could be damaged by
a 2 kΩ load.

Hint: V•Check can be effectively used to eliminate “ghost” voltages.

16

MULTIMETER

If AC detected
If DC detected

Disable and re-enable V•Check

For , and Ω,
Disables V•Check and

Meter puts 2 kΩ
load on circuit.

OFF

COM

V•Check

A

CAT

TEMPERATURE

600V

+

or

locks meter in selected
mode.

2 sec

Re-enables

or

or

V•Check

ip09i.eps

Temperature

16

MULTIMETER

C F

OFF

COM

V•Check

A

CAT

TEMPERATURE

600V

+

Note correct connector polarity.

80BK

Integrated

Temperature

Probe (Type K)

Vent

or

Pipe

ip19f.eps

To meet stated accuracy, the 80BK temperature adapter must be at the
same temperature as the meter.

To avoid possible electric shock, DO NOT apply
thermocouple tip to any conductor that is greater than
30V AC, 42.4V pk, or 60V DC to earth.

W Warning

Capacitance

E

Turn off circuit power; then disconnect and discharge the capacitor before
measuring capacitance.

MULTIMETER

16

If the capacitor requires more
discharging, diSC is displayed
while the capacitor discharges.

OFF

COM

V•Check

A

CAT

TEMPERATURE

600V

+

1 µF 10 µF 100 µF 10,000 µF

+

Note correct probe polarity for polarized capacitors.

ip05i.eps

Microamps

µA

Range 0 to 200 µA

MULTIMETER

16

µA AC µA DC

OFF

COM

Flame

sensor

V•Check

A

CAT

TEMPERATURE

600V

+

Control

module

probe

Example: Flame rectification circuit.

To measure flame rectification circuits:

1. Turn function switch to far right position.

ip20i.eps

2. Push select button 3 times to select µA.

3. Connect meter between flame sensor probe and control module.

4. Turn heating unit on and record µA measurement.

Diode Test

G

Turn off circuit power before testing. For best results diodes
should be measured out of circuit.
Also refer to V•Check.

Good Diode

16

MULTIMETER

Typical voltage

MULTIMETER

16

for silicon diode

Low Impedance

V•Check

OFF

COM

V•Check

A

CAT

TEMPERATURE

600V

+

OFF

COM

V•Check

A

CAT

TEMPERATURE

600V

+

Single beep

ip03i.eps

Forward Bias Reverse Bias

Bad Diode

MULTIMETER

16

MULTIMETER

16

OFF

CAT

600V

COM

+

or

Shorted Open

V•Check

A

TEMPERATURE

OFF

COM

V•Check

A

CAT

TEMPERATURE

600V

+

ip04i.eps

MIN MAX

µF

(Records the lowest and highest measurements)

V•Check, autoranging, and Battery Saver are disabled. Put the meter

in the proper range before entering MIN MAX.

When the reading changes more than about 50 digits, the meter gives a
short beep. When a new minimum or maximum is recorded, the meter
gives a long beep.

Enter

MIN MAX

Present Reading with

Input Change Alert

TM

Maximum Reading

Minimum Reading

2 sec

To Exit

ip10i.eps

MIN MAX with Elapsed Time

µF

Records the hours and minutes between when MIN MAX was entered
and the last high and low was recorded. OL is displayed for times longer
than 99:59.

To enable the MIN MAX timer, hold down
switch from OFF to either measurement mode.

Enter MIN MAX. View

Present Reading

Maximum Reading Maximum Reading

M while turning the rotary

Elapsed Time

Minimum Reading

Elapsed Time

2 sec

Minimum Reading Exit MIN MAX

ip11i.eps

Disabling the Beeper

To disable the beeper for all modes, hold down r for 2 seconds while
turning the meter on.

Continuity Capture

To set up the meter to capture intermittent shorts and opens, turn the
switch to

GR, connect the leads to the circuit; then press M.

Captures transitions longer than 250 µs (1/4000th of a second).

Transitions after the first transition cause the meter to beep, but the
display does not change.

To reset the display to the current condition, press

To exit, press M for 2 seconds, or change the measurement mode.

M.

ip12i.eps

Maintenance

Clean the case with a damp cloth and detergent. Do not use abrasives or
solvents.

Battery Replacement

Remove the test leads before disassembling the case.

C

O

M

6

0

0

V

+

+

Replacement Parts

ip13i.eps

Fluke TL-75 (Double-insulated leads) PN 855705
80BK (Integrated Temperature Probe) PN 1273124

Service and Parts

This meter should be serviced only by a qualified service technician. To
locate an authorized service center, call:

USA: 1-888-99-FLUKE (1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: [phone]
Japan: [phone]
Singapore: [phone]
Anywhere in the world: [phone]

Or, visit Fluke's Web site at www.fluke.com

.

Specifications

Accuracy is specified for a period of one year after calibration, at 18°C to
28°C (64°F to 82°F) with relative humidity to 90%. AC conversions are
ac-coupled, average responding, and calibrated to the rms value of a sine
wave input. Accuracy specifications are given as follows:

±([% of reading] + [number of least significant digits])

Function Range Resolution Accuracy

-10°C to 400°C

Temperature

(Type K Thermocouple) -40°C to -10°C

Error does not include Type K Thermocouple errors.

Function Range Resolution Accuracy

4000 mV1

f

(50 to 400 Hz)

E

4.000V

40.00V

400.0V
600V

4000 mV1

4.000V

40.00V

400.0V
600V

14°F to 752°F

-40°F to 14°F

1 mV

0.001V

00.01V

000.1V
1V

1 mV

0.001V

00.01V

000.1V
1V

0.1°C or

0.1°C or

0.2°F

0.2°F

±(1.0% + 0.8°C)

typical

±(1.0% + 1.5°F) typical

±(5.0% + 1.5°C)

typical

±(5.0% + 3.3°F) typical

±(1.9% + 3)
±(1.9% + 3)
±(1.9% + 3)
±(1.9% + 3)
±(1.9% + 3)

±(0.9% + 2)
±(0.9% + 2)
±(0.9% + 1)
±(0.9% + 1)
±(0.9% + 1)

400.0Ω

4.000 kΩ

Ω

|

40.00 kΩ

400.0 kΩ

4.000 MΩ

40.00 MΩ

1.000 µF

10.00 µF

100.0 µF
10000 µF

ML 2.000V 0.001V ±(1.9% + 2)

1. The 4000 mV range can be entered only in manual range mode. Use the
4000 mV range with accessories.

2. The beeper is guaranteed to come on at <25Ω and turn off at >250Ω. The
meter detects opens or shorts ≥250 µs.

0.1Ω

0.001 kΩ

0.01 kΩ

0.1 kΩ

0.001 MΩ

0.01 MΩ

0.001 µF

0.01 µF

0.1 µF
1 µF

±(0.9% + 2)
±(0.9% + 1)
±(0.9% + 1)
±(0.9% + 1)
±(0.9% + 1)
±(1.5% + 3)

±(1.9% + 2)
±(1.9% + 2)
±(1.9% + 2)

≤1000 µF ±(1.9% + 2)

>1000 µF ±(10% + 90) typical

2

Function Range Resolution Accuracy Burden Voltage

N

(50 Hz to 400 Hz)

M

0 to 200 µA0.1 µA ±(2% + 3 counts) <5 mV/µA

0 to 200 µA0.1 µA ±(1% + 2 counts) <5 mV/µA

Function

f

Overload

Protection

600V rms

1

>5 MΩ <100 pF

Input Impedance (Nominal)

V•Check and LoZ = >2 kΩ <200 pF (ac coupled)

E

f 600V rms >60 dB at dc 50 or 60 Hz

E

J

L 600V rms 2.4-3.0V dc 2.400V dc

600V rms

600V rms >100 dB at dc, 50 or 60 Hz >50 dB at 50 Hz or 60 Hz

600V rms <1.5V dc <450 mV dc <1.5V dc

>10MΩ <100 pF

V•Check and LoZ = >2 kΩ <200 pF

Common Mode Rejection

Ratio (1 kΩ Unbalanced)

Open Circuit Test Voltage

Short Circuit Current

Normal Mode Rejection

Full Scale Voltage

To 4.0 MΩ 40 MΩ

2

2

J 600V rms <500 µA

L

1. 3 x 106 V Hz maximum

2. ≅2 kΩ input impedance up to 50V. Impedance increases with input voltage to
>300 kΩ at 600V.

600V rms

0.95 mA (typical)

MIN MAX Recording Accuracy and Response Time

Specified accuracy of the measurement function ±12 digits in dc for changes
>200 ms in duration (±40 digits in ac). Typical 100 ms response to 80%.

Example 1: This would mean ±1.2° when recording temperature.
Example 2: This would mean ±1.2 µA when recording µA or ±12A if used with a

dc amp probe (with a mV input).

MIN MAX Recording with Elapsed Time

Elapsed Time Resolution Accuracy

0 to 100 hours (99:59) 1 minute 0.3% typical

Maximum Voltage
Between any Terminal
and Earth Ground:

Display: 3 3/4-digits, 4000 counts, updates 4/sec
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Storage Temperature:

Temperature
Coefficient:

Relative Humidity: 0% to 90% (-10°C to 35°C; 14°F to 95°F)

Battery Type: 9V, NEDA 1604 or IEC 6F22
Battery Life: 650 continuous hours with alkaline

600V rms

-30°C to 60°C (-22°F to 140°F)
indefinitely (to -40°C (-40°F) for 100 hrs)

(.1 x specified accuracy)/°C (<18°C or
>28°C)

0% to 70% (35°C to 50°C; 95°F to 122°F)

450 continuous hours with carbon-zinc

Shock: 1 meter drop 6 sides.
Vibration: Class II vibration MIL-PRF-28800F
Size (H x W x L): 3.46 cm x 7.05 cm x 14.23 cm

(1.35 in x 2.75 in x 5.55 in)

Weight: 286g (10 oz)
Safety:

EMI Regulations:

Certifications:

Designed to Protection Class II
requirement of UL3111, ANSI/ISA-S82,
CSA C22.2 No 231, and VDE 0411, and
IEC 1010 overvoltage Category III (CAT
III, 600 Volts).

Complies with FCC Part 15, Class B, and
VDE 0871B. Trademark of TÜV Product
Services. Complies with EN 61010-1:

1993.

P $

TUV, UL and VDE

LIMITED WARRANTY & LIMITATION OF LIABILITY

Each Fluke product is warranted to be free from defects in material and workmanship under
normal use and service. The warranty period is three years and begins on the date of shipment.
Parts, product repairs and services are warranted for 90 days. This warranty extends only to the
original buyer or end-user customer of a Fluke authorized reseller, and does not apply to fuses,
disposable batteries or to any product which, in Fluke's opinion, has been misused, altered,
neglected or damaged by accident or abnormal conditions of operation or handling. Fluke
warrants that software will operate substantially in accordance with its functional specifications for
90 days and that it has been properly recorded on non-defective media. Fluke does not warrant
that software will be error free or operate without interruption.

Fluke authorized resellers shall extend this warranty on new and unused products to end-user
customers only but have no authority to extend a greater or different warranty on behalf of Fluke.
Warranty support is available if product is purchased through a Fluke authorized sales outlet or
Buyer has paid the applicable international price. Fluke reserves the right to invoice Buyer for
importation costs of repair/replacement parts when product purchased in one country is submitted
for repair in another country.

Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase price, free of
charge repair, or replacement of a defective product which is returned to a Fluke authorized
service center within the warranty period.

To obtain warranty service, contact your nearest Fluke authorized service center or send the
product, with a description of the difficulty, postage and insurance prepaid (FOB Destination), to
the nearest Fluke authorized service center. Fluke assumes no risk for damage in transit.
Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB
Destination). If Fluke determines that the failure was caused by misuse, alteration, accident or
abnormal condition of operation or handling, Fluke will provide an estimate of repair costs and
obtain authorization before commencing the work. Following repair, the product will be returned to
the Buyer transportation prepaid and the Buyer will be billed for the repair and return
transportation charges (FOB Shipping Point).

THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, WHETHER
ARISING FROM BREACH OF WARRANTY OR BASED ON CONTRACT, TORT, RELIANCE OR
ANY OTHER THEORY.

Since some countries or states do not allow limitation of the term of an implied warranty, or
exclusion or limitation of incidental or consequential damages, the limitations and exclusions of
this warranty may not apply to every buyer. If any provision of this Warranty is held invalid or
unenforceable by a court of competent jurisdiction, such holding will not affect the validity or
enforceability of any other provision.

Fluke Corporation Fluke Europe B.V.
P.O. Box 9090 P.O. Box 1186
Everett WA 5602 B.D. Eindhoven
98206-9090 The Netherlands

5/94