Fluke 750P3IN, 750P5IN User manual

750P/750R
Pressure Modules
Instruction Sheet
Introduction
The Fluke 750P/750R Series Pressure Modules (the Product) let you measure pressure with a wide range of Fluke calibrators. These calibrators include but are not limited to the:
● 701 and 702 Documenting Process Calibrator
● 719 Portable Pressure Calibrator
● 719Pro Pressure Calibrator
● 721 Pressure Calibrator
● 725 Multifunction Process Calibrator
● 726 Multifunction Process Calibrator
● 741B, 743B, 744 Documenting Process Calibrator
● 753, 754 Documenting Process Calibrator
● 3130 Portable Pneumatic Pressure Calibrator
● 525B T
● 7526A
● 5520A
While the 750P provides basic pressure measurement with various Fluke calibrators, the 750R provides similar functionality with reference-grade accuracy. However on certain calibrators with limited display resolution this may impair the precision of pressure measurement. See Pressure Module Ranges chart for more information.
The Product measures pressure with an internal microprocessor compensated sensor. It receives power from and sends digital information to the Fluke calibrator.
PN 4387748 December 2013
© 2013 Fluke Corporation. Product specications are subject to change
without notice. Printed in USA. All rights reserved.
emperature/Pressure Calibrator Precision Process Calibrator and 5522A Multi-Product Calibrator
Gage pressure modules have one pressure tting and
measure pressure with respect to atmospheric pressure.
Differential pressure modules have two pressure ttings and
measure the difference between the applied pressure on the
high tting versus the low tting. A differential pressure module functions like a gage module when the low tting is open. The
absolute pressure modules measure pressure with respect to an absolute vacuum. The vacuum pressure modules measure negative pressure.
See the Users Manual for your specic Fluke calibrator for
operation instructions. Differential and Gage models are shown in Figure 1.
Mechanical Damage Prevention
Caution
To avoid Product damage, never apply more than 10 ft­lbs of torque between the pressure module ttings or between the ttings and the body of the module. Always apply appropriate torque between the pressure module tting and connecting ttings or adapters.
Over Pressure Damage Prevention
Caution
To avoid Product damage:
Low
Differential
RANGE
700
PRESSURE MODULE
P
04
15 PSID/G
1 bar100 kPa
High
RANGE
700
PRESSURE MODULE
100 PSIG
Gage
P
06
7 bar700 kPa
hhb001.jpg
● Use the Product only with specied media as shown
on the Product label to avoid Product damage from corrosion.
o avoid product damage do not apply pressure in
● T
excess of 120 % of the specied upper limit.
Figure 2 shows correct and incorrect ways to use a wrench to
apply torque to the pressure module tting.
RANGE
100 kPa
Figure 1. Differential and Gage Pressure Modules
Safety Information
A Warning identies conditions and procedures that are dangerous to the user. A Caution identies conditions and
procedures that can cause damage to the Product or the equipment under test.
Warning
To avoid injury due to the release of high-pressure uid:
● Use only adapters and ttings rated to withstand the appropriate pressure. Ensure that all adapters and
ttings are securely connected.
Never exceed the specied BURST PRESSURE for
the product.
To avoid a violent release of pressure in a pressurized system, shut off the isolation valve and slowly bleed off the pressure before you attach or remove the
pressure module from the pressure line.
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Figure 2. Applying Torque
hhb002.eps
Table 1. Symbols
Symbol Meaning
f
Risk of Danger. Important. See Manual. Conforms to European Union directives. Conforms to relevant North American Safety
Standards. Conforms to relevant South Korean EMC
Standards. Pressure (found on Fluke calibrators) Conforms to relevant Australian EMC
requirements. This product complies with the WEEE
Directive (2002/96/EC) marking
requirements. The afxed label indicates
that you must not discard this electrical/ electronic product in domestic household
waste. Product Category: With reference to the equipment types in the WEEE Directive
Annex I, this product is classed as category
9 “Monitoring and Control Instrumentation” product. Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website for recycling information.
Recommended Measurement Technique
For best results, before you zero the Product or take measurements, pressurize the Product to full scale and then vent to zero pressure (atmosphere).
Note
Low-range pressure modules may be sensitive to gravity.
For best results, pressure modules 30 psi and below should be held at the same physical orientation from the time they are zeroed until the measurement is complete.
Box Contents
The Product package should contain the listed items below. If it does not, contact Fluke immediately. See “Contact Fluke”.
● Pressure module
● 1/8 NPT
● 1/8 NPT
● 1/8 NPT
● O-RING,(-1
Certicate of calibration
● User documentation packet
male to 1/4 NPT male adapter male to 1/4 BSP male adapter male to M20 male adapter
11) CAST URETHANE
Pressure Calibration Kit
The optional Fluke 700PCK (Pressure Calibration Kit) accessory lets you calibrate the pressure modules at your facility with your precision pressure standards. A pressure calibrator or dead weight tester that is at least 4X more accurate than the pressure module under test is recommended.
Performance Test
If you need to check that the pressure module meets its
accuracy specication, use a dead weight tester or suitable
pressure calibrator. The accuracy of the dead weight tester
or pressure calibrator should be signicantly better than the Product pressure specication. Proceed as follows to verify that a pressure module is operating within specication:
Read the pressure value with no externally applied
1. pressure to make sure the 0 % of scale is correct. When reading the pressure, press the ZERO key to remove any zero of
Connect the pressure module to a dead weight tester
2.
Set the dead weight tester to 20 % of the pressure
3. module’
Make sure the reading agrees with the dead weight
4.
tester value within the specications.
5. Set the dead weight tester to 40, 60, 80, and 100 % of full scale and compare the respective readings.
fset.
s full scale value.
Specications
Mechanical Specications
Size (H X W X L) .......45 mm X 94 mm X 110 mm
. . . . . . . . . . . . . . . . . . . . .(1.77 in X 3.70 in X 4.33 in)
Weight . ..............292 g (10.3 oz)
Physical Interface
.......Serial Connector
, Pressure Port
Environmental Specications
Operating Temperature...-10 °C to +50 °C (14 °F to 122 °F)
Storage Temperature ....-20 °C to +60 °C (-4 °F to 140 °C)
Operating Humidity......Non condensing (<10 °C) (<50 °F)
90 % RH (10 °C to 30 °C) (50 °F to 86 °F) 75 % RH (30 °C to 40 °C) (86 °F to 104 °F) 45 % RH (40 °C to 50 °C) (104 °F to 122 °C)
Operating Altitude ......2000 m (6,561 ft)
Storage Altitude ........12000 m (45,700 ft)
IP
.
Compliance
Agency Approvals.......
CE...................IEC 61010-1
EMI, RFI, EMC
..............IP
Rating
52
Protection Class II Pollution Degree 2
.........EN61326-1
Electromagnetic Compatibility Applies to use in Korea only Class A equipment (Industrial Broadcasting & Communication Equipment) [1] This Product meets requirements for industrial (Class A) electromagnetic wave equipment and the seller or user should take notice of it. is intended for use in business environments and is not to be used in homes.
.
[1]
This equipment
.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or
handling. Resellers are not authorized to extend any other
warranty on Fluke’s behalf. To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that Service Center with a description of the problem. THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or
countries do not allow the exclusion or limitation of an implied
warranty or of incidental or consequential damages, this limitation of liability may not apply to you.
11/99
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
[3]
(23 +/- 3degC)
[4]
Total Uncertainty 1 year
(15-35 degC)
Total Uncertainty 1 year
(0-50 degC)
[1]
Total Uncertainty 6 month
(15-35 degC)
Total Uncertainty 6 month
750 Model Number Parameter/Range
Burst Rating
[6]
Hi Side Media Compatibility
[2]
Lo Side Media Compatibility
Pressure Module Ranges
Reference Uncertainty
[2]
750P00 0 to 1 Inch H2O (0 to 2.5 mBar) 30X NONCORROSIVE GASSES NONCORROSIVE GASSES ±0.15 % ±0.3 % ±0.35 % ±0.25 % ±0.30 % 750P01 0 to 10 Inch H2O (0 to 25 mBar) 3X NONCORROSIVE GASSES NONCORROSIVE GASSES ±0.1 % ±0.2 % ±0.3 % ±0.15 % ±0.25 % 750P02 0 to 1 psi (0 to 70 mBar) 3X NONCORROSIVE GASSES NONCORROSIVE GASSES ±0.050 % ±0.1 % ±0.15 % ±0.075 % ±0.125 % 750P22 0 to 1 psi (0 to 70 mBar) 3X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.050 % ±0.1 % ±0.15 % ±0.075 % ±0.125 % 750P03 0 to 5 psi (0 to 350 mBar) 3X NONCORROSIVE GASSES NONCORROSIVE GASSES ±0.02 % ±0.04 % ±0.05 % ±0.035 % ±0.04 % 750P23 0 to 5 psi (0 to 350 mBar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.02 % ±0.04 % ±0.05 % ±0.035 % ±0.04 % 750P04 0 to 15 psi (0 to 1 Bar) 3X NONCORROSIVE GASSES NONCORROSIVE GASSES ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P24 0 to 15 psi (0 to 1 Bar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750P05 0 to 30 psi (0 to 2 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P06 0 to 100 psi (0 to 7 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P27 0 to 300 psi (0 to 20 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P07 0 to 500 psi (0 to 35 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P08 0 to 1000 psi (0 to 70 Bar) 3X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P09 0 to 1500 psi (0 to 100 Bar) 3X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750P2000 0 to 2000 psi (0 to 140 Bar) 3X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750P29 0 to 3000 psi (0 to 200 Bar) 3X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P30 0 to 5000 psi (0 to 340 Bar) 3X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750P31 0 to 10000 psi (0 to 700 Bar) 2X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750PA3 0 to 5 psia (0 to 350 mBar) 4X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 % 750PA4 0 to 15 psia (0 to 1 Bar) 4X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 % 750PA5 0 to 30 psia (0 to 2 Bar) 4X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 % 750PA6 0 to 100 psia (0 to 7 Bar) 4X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 %
750PA27 0 to 300 psia (0 to 20 Bar) 4X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 %
750PA7 0 to 500 psia (0 to 35 Bar) 4X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 % 750PA8 0 to 1000 psia (0 to 70 Bar) 3X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 % 750PA9 0 to 1500 psia (0 to 100 Bar) 3X Stainless Steel SS-316 N/A ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 %
750PV3 -5 psi (-350 mBar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 % 750PV4 -15 psi (-1 Bar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 %
750PD2 -1 to 1 psi (-70 to 70 mBar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.05 % ±0.1 % ±0.15 % ±0.075 % ±0.125 % 750PD3 -5 to 5 psi (-350 to 350 mBar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.03 % ±0.06 % ±0.07 % ±0.05 % ±0.06 %
750PD10 -10 to 10 psi (-700 to 700 mBar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.025 % ±0.05 % ±0.07 % ±0.04 % ±0.06 %
750PD4 -15 to 15 psi (-1 to 1 Bar) 4X Stainless Steel SS-316 NONCORROSIVE GASSES ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750PD5 -15 to 30 psi (-1 to 2 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750PD50 -15 to 50 psi (-1 to 3.5 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750PD6 -15 to 100 psi (-1 to 7 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 % 750PD7 -15 to 200 psi (-1 to 14 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750PD27 -15 to 300 psi (-1 to 20 Bar) 4X Stainless Steel SS-316 N/A ±0.0175 % ±0.035 % ±0.045 % ±0.03 % ±0.04 %
750R04 750R06
[5] [5]
0 to 15 psi (0 to 1 Bar) 3X NONCORROSIVE GASSES NONCORROSIVE GASSES ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS
0 to 100 psi (0 to 7 Bar) 4X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS 750R27 0 to 300 psi (0 to 20 Bar) 4X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS 750R07 0 to 500 psi (0 to 35 Bar) 4X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS
750R08
[5]
0 to 1000 psi (0 to 70 Bar) 3X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS 750R29 0 to 3000 psi (0 to 200 Bar) 3X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS 750R30 0 to 5000 psi (0 to 340 Bar) 3X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS
[5]
750R31
750RD5 -15 to 30 psi (-1 to 2 Bar) 4X NONCORROSIVE GASSES N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS
[5]
750RD6
0 to 10000 psi (0 to 700 Bar) 2X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS
-12 to 100 psi (-1 to 7 Bar) 4X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS
750RD27 -12 to 300 psi (-0.8 to 20 Bar) 4X Stainless Steel SS-316 N/A ±0.01 % of FS ±0.02 % of FS ±0.04 % of FS ±0.015 % of FS ±0.035 % of FS
1. Total uncertainty, % of full span for temperature range 0°C to +50°C, one year interval. Total uncertainty, 1.0% of full span for temperature range -10°C to 0°C, one
year interval. No 6 month specication available for range -10°C to 0°C.
“NONCORROSIVE GASSES” indicates dry air or non-corrosive gas as compatible media. “Stainless Steel 316-SS” indicates media compatible with T
2. Stainless Steel.
Specications % of Full Span unless otherwise noted.
3.
Find Quality Products Online at: sales@GlobalTestSupply.com
ype 316
www.GlobalTestSupply.com
Reference Uncertainty is the specication for as left data for 24 hours.
4.
5. When reference class modules
specication.
Burst rating specication refers to the multiplier times full scale of the module for the rated burst pressure.
6.
(0-50 degC)
[1]
Loading...