Fluke 750PA8, 750PA9, 750PA6, 750PA7, 750PD27 Instruction Manual

Fluke 750P

Series Pressure

Modules

Precision pressure measurement for
75X and 720 series calibrators

The 750P Series Pressure Modules are the ideal pressure
modules to enable gage, differential and absolute pressure
measurement with Fluke 750 and 740 series DPCs and 725,
726 MPCs to measure pressure.

• 0.025 % reference uncertainty

• 6-month and 1-year specifications

• Temperature compensated 0 °C to 50 °C

• Digital communication to calibrators, no analog

losses or errors

• Broad selection of ranges

• Gage, differential, dual range, absolute and vacuum

measurement models

A complete family of pressure modules

A family of 48 pressure modules covers pressure
calibrations from 0 to 1 in H
to 690 bar).

Gage pressure modules have one pressure fitting
and measure the pressure with respect to atmospheric
pressure. Differential pressure modules have two pres­sure fittings and measure the difference between the
applied pressure on the high fitting versus the low
fitting. Each module is clearly labeled for range, over­pressure and media compatibility. All modules include
NPT, metric (BSP) and M20 adapters.

Quick and easy measurements

Fluke 750P Series Pressure Modules are easy to use.
To measure pressure, connect the pressure module to
a pressure source or hand pump and then connect the
pressure module cable to the calibrator. Apply pressure
from the pressure source and it is displayed digitally
on the calibrator. At the touch of a button, the pressure
may be displayed in up to 11 different engineering
units. When used with the 750 Series Documenting
Process Calibrators, pressure readings can be date/time
stamped and stored electronically for later retrieval.
This saves time, eliminates errors, and supports com­pliance with quality standards and regulations.

85

0 to 10000 psi (2.5 mBar

2

Technical Data

Pressure module performance
and technology

Fluke 750P Series pressure modules are highly
accurate, with specifications that apply from 0 °C to
50 °C (32 °F to 122 °F), a feature that sets them apart
from other pressure calibrators. Many ranges have
total uncertainties of 0.04
uncertainties of 0.01
table).

This performance is possible through the innova­tive application of mathematics and micro-processor
power. Fluke pressure modules have silicon piezo­resistor sensors which consist of a resistive bridge
fabricated in a silicon diaphragm. Pressure applied to
the diaphragm causes a change in the balance of the
bridge which is proportional to the applied pressure.
The bridge balance change is not linear and is very
sensitive to temperature. However, since these effects
are quite stable with time and with repetitive changes
of condition, the sensors are carefully characterized.

During manufacture, Fluke pressure module sensors
are characterized by reading temperature and pressure
at multiple points. A least-squares regression is used
to calculate the coefficients of a polynomial expression
for pressure. The coefficients, unique to that pressure
module, are stored in the module’s memory.

Each module has its own microprocessor, allowing
it to run the measurement circuitry and to commu­nicate digitally with a calibrator. When connected to
the calibrator, the modules coefficients are uploaded
from the pressure module to the calibrator. Then, as
pressure measurements are made, raw sensor values
for pressure and temperature are digitally loaded to
the calibrator, where the raw sensor values and coef­ficients are manipulated to derive and display the
pressure reading.

This innovative technique provides several benefits:

1. Digital communication eliminates errors due to poor

connections and electrical interference.

2. The modules are inherently temperature-

compensated from 0 °C to 50 °C (32 °F to 122 °F).

% of full scale and reference

% of full scale (see specification

3. The modules are fully interchangeable because
all measurements are completed in the pres­sure module itself and then communicated to the
calibrator in digitized form. Modules are calibrated
independently of the calibrator, and can be used
with any 740, 750 or compatible 720 or 710 series
calibrator. Each module has its own serial number
to maintain independent traceability.

Sensor protection in isolated modules

Many of these modules (see table) incorporate a stain­less steel diaphragm to isolate the sensor. With these
modules, any medium that is compatible with stainless
steel can be used on the high side of the module.

Rugged construction

A urethane overmolding protects against shock if a
module is accidentally dropped and also seals against
dirt, dust, and moisture. Pressure connections are

1

” NPT female connection. A ¼” NPT Male, ¼” BSP/

/

8

ISO and M20 male adapter are also provided with each
pressure module.

Convenient setup

A one-meter cable between the pressure module and
calibrator reduces the length of connecting tubing to
the pressure source. The remote pressure head also
provides an extra margin of safety and convenience
by removing the calibrator and operator from the
pressure source in the event or need for semi-remote
measurements.

2 Fluke Corporation Fluke 750P Series Pressure Modules

Pressure accessories

Image Description Application

Fluke 700PTP-1 Pneumatic Test Pump

The Fluke 700PTP-1 is a handheld pressure
pump designed to generate either vacuum
to -13 psi/-0.9 bar or pressure to
600 psi/40 bar

The Fluke 700PTP-1 has two pressure ports:

• ¼” NPT female parallel thread fitting for
the reference gauge or pressure module

• ¼” NPT female parallel thread fitting for
the unit under test

Fluke 700HTP-2Hydraulic Test Pump

The Fluke 700HTP-1 is designed to generate
pressures up to 10000 psi/700 bar. The
Fluke 700HTP-1 has two pressure ports:

• ¼” NPT female parallel thread fitting for
the reference gauge or pressure module

• ¼” NPT female parallel thread fitting for
the unit under test

Note: The user must provide a hose with appropriate end
fittings from this port to the unit under test.

Fluke 700LTP-1 Low-Presure Test Pump

The Fluke 700LTP-1 is a hand operated
pressure pump designed to generate either
vacuum to -12 psi/-.85 bar or pressures to
100 psi/6.9 bar. The Fluke 700LTP-1 has
two pressure ports with push fit connec­tors. These push fit connectors, one for the
reference port for connection to a Fluke 700
Series Pressure Module and one to connect
to a unit under test, connect to the supplied
test hoses.

Fluke 700HTH-1 Hydraulic Test Hose

The Fluke 700HTH-1 Hydraulic Test Hose
is a 10000 psi, 700 bar working pressure
test hose. The hose uses self-sealing fittings
with easy finger tight connections.

The Fluke 700PTP-1 features an integral pressure adjustment vernier
which varies the pressurized volume by 2.0 cc over approximately
eleven turns of the vernier knob. The pressure variation achievable with
the vernier will depend on the nominal pressure and total pressurized
volume, but with a minimum volume and maximum pressure, the vernier
provided 600 ± 20 psi adjustment range. With a minimum volume and
no pressure applied, the vernier can also be used to provide a 0 to 70˝
H2O range. Larger volumes will provide a smaller range of adjustment,
but greater resolution. The length of the stroke can be adjusted to limit
the maximum output pressure. Maximum output pressure is adjustable
from 2.5 psi to 600 psi.

For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators

This pump can provide up to 10000 psi using distilled water or mineral­based hydraulic oil. The pump is operated by pumping several strokes
to prime the system, then switching to high pressure mode when the
resistance increases. An integral pressure adjustment vernier knob varies
the pressurized volume by 0.6 cc. The pressure variation achievable with
the vernier will depend on the nominal pressure and total pressurized
volume, but with a minimum volume, the vernier provided 150 psi to
3000 psi (at 150 psi nominal) and 3000 psi to10000 psi (at 3000 psi
nominal) adjustment ranges. With a minimum volume and no pressure
applied, the vernier can also be used to provide a 0 to 1.7 psi range.
Larger volumes will provide a smaller range of adjustment, but greater
resolution.

For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators

The Fluke 700LTP-1 is primarily intended for low pressure applications.
It features a fine adjust vernier with .00145 psi resolution at low pres­sures. The pressure variation achievable with the vernier will depend on
the nominal pressure and total pressurized volume, but with minimum
volume and maximum pressure the vernier provides 30 psi ± 6 psi. The
adjustable pressure relief valve features a slow-bleed capability that
allows the user to slowly release pressure at a controlled rate to achieve
a desired pressure.

The Fluke 700HTH-1 allows connections to a unit under test from a
Fluke 700HTP-1 hydraulic test pump in use with the Fluke 700 and
750P Series Pressure Modules. The 700HTH-1 is compatible with water
and non-corrosive oil.

Fluke 71X Hose Kit

The Fluke 71X hose kit includes (2) quick
disconnect fittings to connect to the 718 or
719, (3) 1-meter translucent hoses and one
BSP adapter.

Fluke 700PRV-1 Pressure Relief Valve Kit

The Fluke 700PRV-1 consists of two relief
valves (1360 and 5450 psi) to be used with
the 700HTP-1 Hydraulic Test Pump. These
relief valves will protect the Fluke pressure
modules from damage due to over-pressur­ization. 1/4 BSP male parallel thread to fit
Fluke 700HTP-1.

Fluke 700 PMP Pressure Pump

The Fluke 700PMP is a hand-operated pres­sure pump to provide pressures up to
150 psi/1000 kPa. Output fitting is 1/8
FNPT.

3 Fluke Corporation Fluke 750P Series Pressure Modules

For use with: Fluke 718 and 719 Pressure Calibrators

Repeatability ± 10 % of nominal setting. Multiturn adjustment screw to
set preload on internal disc springs.

For use with: Fluke 700HTP-1 Hydraulic Test Pump.

Linear stroke of 1.6 in (4 cm). Multi-turn vernier for fine adjustment of
pressure. Includes controlled pressure bleed valve.

For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators.

General specifications

Model Parameter/

Range

Differential
750P00 0 to 1 in H2O

(0 to 2.5 mBar)

750P01 0 to 10 in H2O

(0 to 25 mBar)

750P02 0 to 1 psi

(0 to 70 mBar)

750P22 0 to 1 psi

(0 to 70 mBar)

750P03 0 to 5 psi

(0 to 350 mBar)

750P23 0 to 5 psi

(0 to 350 mBar)

750P04 0 to 15 psi

(0 to 1 bar)

750P24 0 to 15 psi

(0 to 1 bar)

Gage
750P05 0 to 30 psi

(0 to 2 bar)

750P06 0 to 100 psi

(0 to 7 bar)

750P27 0 to 300 psi

(0 to 20 bar)

750P07 0 to 500 psi

(0 to 35 bar)

750P08 0 to 1000 psi

(0 to 70 bar)

750P09 0 to 1500 psi

(0 to 100 bar)

750P2000 0 to 2000 psi

(0 to 140 bar)

High
750P29 0 to 3000 psi

(0 to 200 bar)

750P30 0 to 5000 psi

(0 to 340 bar)

750P31 0 to 10000 psi

(0 to 700 bar)

Absolute
750PA3 0 to 5 psia

(0 to 350 mBar)

750PA4 0 to 15 psia

(0 to 1 bar)

750PA5 0 to 30 psia

(0 to 2 bar)

750PA6 0 to 100 psia

(0 to 7 bar)

750PA27 0 to 300 psia

(0 to 20 bar)

750PA7 0 to 500 psia (0

to 35 bar)

750PA8 0 to 1000 psia

(0 to 70 bar)

750PA9 0 to 1500 psia

(0 to 100 bar)

Burst
Rating

30X Dry Air Dry Air ±0.15 % ± 0.3 % ± 0.35 % ± 0.25 % ± 0.30 %

3X Dry Air Dry Air ±0.1 % ± 0.2 % ± 0.3 % ± 0.15 % ± 0.25 %

3X Dry Air Dry Air ±0.050 % ± 0.1 % ± 0.15 % ± 0.075 % ± 0.125 %

3X 316 SS Dry Air ±0.050 % ± 0.1 % ± 0.15 % ± 0.075 % ± 0.125 %

3X Dry Air Dry Air ±0.02 % ± 0.04 % ± 0.05 % ± 0.035 % ± 0.04 %

4X 316 SS Dry Air ±0.02 % ± 0.04 % ± 0.05 % ± 0.035 % ± 0.04 %

3X Dry Air Dry Air ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

4X 316 SS Dry Air ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

4X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

4X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

4X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

4X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

3X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

3X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

3X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

3X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

3X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

2X 316 SS N/A ±0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

4X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

4X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

4X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

4X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

4X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

4X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

3X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

3X 316 SS N/A ±0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

Hi Side

6

Media

Lo Side

2

Media

Reference

2

Uncertainty

Total

4

Uncertainty
1-year
(15-35 �C)

Total
Uncertainty

1

1-year

Total
Uncertainty
6-month
(15-35 �C)

Total
Uncertainty
6-month

1

4 Fluke Corporation Fluke 750P Series Pressure Modules

General specifications (continued)

Model Parameter/

Range

Burst
Rating

Hi Side

6

Media

Lo Side

2

Media

Reference

2

Uncertainty

Total

4

Uncertainty
1-year
(15 �C to 35 �C)

Total
Uncertainty

1

1-year

Total
Uncertainty
6-month
(15 �C to 35 �C)

Total
Uncertainty
6-month

1

Vacuum
750PV3 -5 psi

4X 316 SS Dry Air ± 0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

(-350 mBar)

750PV4 -15 psi

4X 316 SS Dry Air ± 0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %

(-1 bar)

Dual
750PD2 -1 to 1 psi

4X 316 SS Dry Air ± 0.05 % ± 0.1 % ± 0.15 % ± 0.075 % ± 0.125 %

(-70 to 70 mBar)

750PD3 -5 to 5 psi

4X 316 SS Dry Air ± 0.03 % ± 0.06 % ± 0.07 % ± 0.05 % ± 0.06 %
(-350 to
350 mBar)

750PD10 -10 to 10 psi

4X 316 SS Dry Air ± 0.025 % ± 0.05 % ± 0.07 % ± 0.04 % ± 0.06 %
(-700 to
700 mBar)

750PD4 -15 to 15 psi

4X 316 SS Dry Air ± 0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %
(-1 to 1 bar)

750PD5 -15 to 30 psi

4X 316 SS — ± 0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %
(-1 to 2 bar)

750PD50 -15 to 50 psi

4X 316 SS — ± 0.0175

% ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

(-1 to 3.5 bar)

750PD6 -15 to 100 psi

4X 316 SS — ± 0.0175

% ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %

(-1 to 7 bar)

750PD7 -15 to 200 psi

4X 316 SS — ± 0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %
(-1 to 14 bar)

750PD27 -15 to 300 psi

4X 316 SS — ± 0.0175 % ± 0.035 % ± 0.045 % ± 0.03 % ± 0.04 %
(-1 to 20 bar)

Reference

750R0450 to 15 psi

3X Dry Air Dry Air ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 1 bar)

750R0650 to 100 psi

4X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 7 bar)

750R27 0 to 300 psi

4X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 20 bar)

750R07 0 to 500 psi

4X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 35 bar)

750R0850 to 1000 psi

3X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 70 bar)

750R29 0 to 3000 psi

3X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 200 bar)

750R30 0 to 5000 psi

3X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 340 bar)

750R3150 to 10000 psi

2X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(0 to 700 bar)

750RD5 -15 to 30 psi

4X Dry Air — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(-1 to 2 bar)

750RD65-12 to 100 psi

4X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(-1 to 7 bar)

750RD27 -12 to 300 psi

4X 316 SS — ± 0.01 % of FS ± 0.02 % of FS ± 0.04 % of FS ± 0.015 % of FS ± 0.035 % of FS
(-0.8 to 20 bar)

1. Total uncertainty, % of full span for temperature range 0 °C to +50 °C, one year interval. Total uncertainty, 1.0% of full span for temperature range -10 °C to 0 °C, one year interval. No 6
month specification available for range -10 °C to 0 °C.

2. “NONCORROSIVE GASSES” indicates dry air or non-corrosive gas as compatible media. “Stainless Steel 316-SS” indicates media compatible with Type 316 Stainless Steel.

3. Specifications % of Full Span unless otherwise noted.

4. * Reference Uncertainty is the specification for as left data for 24 hours.

5. When reference class modules are used with fixed resolution products (717, 718, 719 series, 725 and 726) calibrators add ± 1 count to the overall accuracy specification.

6. Burst rating specification refers to the multiplier times full scale of the module for the rated burst pressure.

5 Fluke Corporation Fluke 750P Series Pressure Modules

Ordering information

FLUKE-750P00

FLUKE-750P01

FLUKE-750P22 Pressure Module, 0 psi to 1 psi (0 to 70 mBar), (0 to 7 kPa)
FLUKE-750P23 Pressure Module, 0 psi to 5 psi (0 to 350 mBar), (0 to 35 kPa)
FLUKE-750P04 Pressure Module, 0 psi to 15 psi (0 to 1 bar), (0 to 100 kPa)
FLUKE-750P24 Pressure Module, 0 psi to 15 psi (0 to 1 bar), (0 to 100 kPa)
FLUKE-750P05 Pressure Module, 0 psi to 30 psi (0 to 2 bar), (0 to 200 kPa)
FLUKE-750P06 Pressure Module, 0 psi to 100 psi (0 to 7 bar), (0 to 700 kPa)
FLUKE-750P27 Pressure Module, 0 psi to 300 psi (0 to 20 bar), (0 to 2000 kPa)
FLUKE-750P07 Pressure Module, 0 psi to 500 psi (0 to 35 bar), (0 to 3500 kPa)
FLUKE-750P08 Pressure Module, 0 psi to 1000 psi (0 to 70 bar), (0 to 7000 kPa)
FLUKE-750P09 Pressure Module, 0 psi to 1500 psi (0 to 100 bar), (0 to 10 MPa)
FLUKE-750P2000 Pressure Module, 0 psi to 2000 psi (0 to 140 bar), (0 to 14 MPa)
FLUKE-750P29 Pressure Module, 0 psi to 3000 psi (0 to 200 bar), (0 to 20 MPa)
FLUKE-750P30 Pressure Module, 0 psi to 5000 psi (0 to 340 bar), (0 to 34 MPa)
FLUKE-750P31 Pressure Module, 0 psi to 10000 psi (0 to 700 bar), (0 to 70 MPa)
FLUKE-750PA3 Pressure Module, 0 psi to 5 psi (0 to 350 mBar), (0 to 35 kPa)
FLUKE-750PA4 Pressure Module, 0 psi to 15 psi (0 to 1 bar), (0 to 100 kPa)
FLUKE-750PA5 Pressure Module, 0 psi to 30 psi (0 to 2 bar), (0 to 200 kPa)
FLUKE-750PA6 Pressure Module, 0 psi to 100 psi (0 to 7 bar), (0 to 700 kPa)
FLUKE-750PA27 Pressure Module, 0 psi to 300 psi (0 to 20 bar), (0 to 2000 kPa)
FLUKE-750PA7 Pressure Module, 0 psi to 500 psi (0 to 35 bar), (0 to 3500 kPa)
FLUKE-750PA8 Pressure Module, 0 psi to 1000 psi (0 to 70 bar), (0 to 7000 kPa)
FLUKE-750PA9 Pressure Module, 0 psi to 1500 psi (0 to 100 bar), (0 to 10 MPa)
FLUKE-750PV3 Pressure Module, -5 psi (-350 mBar), (-35 kPa)
FLUKE-750PV4 Pressure Module, -15 psi (-1 bar), (-100 kPa)
FLUKE-750PD2 Pressure Module, -1 psi to 1 psi (-70 to 70 mBar), (-7 to 7 kPa)
FLUKE-750PD3 Pressure Module, -5 psi to 5 psi (-350 to 350 mBar), (-35 to 35 kPa)
FLUKE-750PD10 Pressure Module, -10 psi to 10 psi (-0.7 to 0.7 bar), (-70 to 70 kPa)
FLUKE-750PD4 Pressure Module, -15 psi to 15 psi (-1 to 1 bar), (-100 to 100 kPa)
FLUKE-750PD5 Pressure Module, -15 psi to 30 psi (-1 to 2 bar), (-100 to 200 kPa)
FLUKE-750PD50 Pressure Module, -15 psi to 50 psi (-1 to 3.5 bar), (-100 to 350 kPa)
FLUKE-750PD6 Pressure Module, -15 psi to 100 psi (-1 to 7 bar), (-100 to 700 kPa)
FLUKE-750PD7 Pressure Module, -15 psi to 200 psi (-1 to 14 bar), (-100 to 1400 kPa)
FLUKE-750PD27 Pressure Module, -15 psi to 300 psi (-1 to 20 bar), (-100 to 2000 kPa)
FLUKE-750R04 Pressure Module, 0 psi to 15 psi (0 to 1 bar) (0 to 100 kPa)
FLUKE-750R06 Pressure Module, 0 psi to 100 psi (0 to 7 bar), (0 to 700 kPa)
FLUKE-750R27 Pressure Module, 0 psi to 300 psi (0 to 20 bar), (0 to 2000 kPa)
FLUKE-750R07 Pressure Module, 0 psi to 500 psi (0 to 35 bar), (0 to 3500 kPa)
FLUKE-750R08 Pressure Module, 0 psi to 1000 psi (0 to 70 bar), (0 to 7000 kPa)
FLUKE-750R29 Pressure Module, 0 psi to 3000 psi (0 to 200 bar), (0 to 20 MPa)
FLUKE-750R30 Pressure Module, 0 psi to 5000 psi (0 to 340 bar), (0 to 34 MPa)
FLUKE-750R31 Pressure Module, 0 psi to 10000 psi (0 to 700 bar), (0 to 700 MPa)
FLUKE-750RD5 Pressure Module, -15 psi to 30 psi (-1 to 2 bar), (-100 to 200 kPa)
FLUKE-750RD6 Pressure Module, -12 psi to 100 psi (-0.8 to 7 bar), (-80 to 700 kPa)
FLUKE-750RD27 Pressure Module, -12 psi to 300 psi (-0.8 to 20 bar), (-80 to 2000 kPa)
FLUKE-750P03 Pressure Module, 0 psi to 5 psi (0 to 350 mBar), (0 to 35 kPa)
FLUKE-750P02 Pressure Module, 0 psi to 1 psi (0 to 70 mBar), (0 to 7 kPa)

Pressure Module, 0 psi to 1 psi in H

Pressure Module, 0 psi to 10 psi in H2O (0 to 25 mBar),(0 to 2.5 kPa)

O (0 to 2.5 mBar), (0 to 0.25 kPa)

2

Included equipment

Manual, traceable calibration certificate, and adapters.

Fluke. The Most Trusted Tools
in the World.

Fluke Corporation
PO Box 9090, Everett, WA 98206 U.S.A.

Fluke Europe B.V.
PO Box 1186, 5602 BD
Eindhoven, The Netherlands

For more information call:
In the U.S.A. [phone] or
Fax [phone]
In Europe/M-East/Africa [phone] or
Fax [phone]
In Canada (800)-36-FLUKE or
Fax [phone]
From other countries [phone] or
Fax [phone]
Web access: http://www.fluke.com

©2014 Fluke Corporation.
Specifications subject to change without notice.
Printed in U.S.A. 1/2014 6001669A_EN

Modification of this document is not permitted
without written permission from Fluke Corporation.

6 Fluke Corporation Fluke 750P Series Pressure Modules