ScopeMeter®190C/190B Series
®
and ScopeMeter
120 Series
Technical Data
ScopeMeter 190C and 190B
Series: Speed, performance
and analysis power
E
G
M
A
E
N
N
A
T
M
S
Y
T
I
L
A
U
Q
C
E
R
T
I
F
I
E
I
D
T
T
E
O
E
M
Now expanded with 3K memory and
FFT Frequency Spectrum Analysis
For demanding applications, the
Y
S
T
E
ScopeMeter 190C and 190B Series
M
high-performance oscilloscopes
offer specifications usually found on
1
0
0
9
top-end bench instruments. With
O
S
up to 200 MHz bandwidth,
2.5 GS/s real time sampling and a
deep memory of 27,500 points per
R
input they’re ideal for engineers
who need the full capabilities of a
high-performance scope in a handheld, battery powered instrument.
Dual input - 200, 100 or
•
60 MHz bandwidth
Up to 2.5 GS/s real time
•
sampling per input
High Waveform Resolution of
•
3000 datapoints per channel
Frequency Spectrum using FFT
•
analysis (190C)
Connect-and-View™automatic
•
triggering, a full range of manual trigger modes plus external
triggering
Digital Persistence for analyzing
•
complex, dynamic signals like
on an analog oscilloscope (190C)
Fast display update rate for
•
seeing dynamic behavior
instantaneously
Automatic capture and replay of
•
100 screens
27,500 points and more per
•
input record length using
ScopeRecord
1,000 V CAT II and 600 V CAT
•
III safety certified
Up to 1,000 V independently
•
floating isolated inputs
Four hours rechargeable
•
NiMH battery pack
™
mode
ScopeMeter 120 Series:
Three-in-one simplicity
The compact ScopeMeter 120 Series
is the rugged solution for industrial
troubleshooting and installation
applications. It’s a truly integrated
test tool, with oscilloscope, multimeter and “paperless” recorder in
one affordable, easy-to-use instrument. Find fast answers to problems
in machinery, instrumentation,
control and power systems.
A dual input 40 MHz or 20 MHz
•
digital oscilloscope
Two 5,000 counts true-rms
•
digital multimeters
Cursor measurements (Fluke 124)
•
A dual input TrendPlot recorder
•
Connect-and-View trigger
•
simplicity for hands-off operation
Shielded test leads for oscillo-
•
scope, resistance, continuity
and capacitance measurements
Full bandw
•
40 MHz probe included standard
with Fluke 124
Up to seven hours battery
•
operation
600 V CAT III safety certified
•
Optically isolated RS-232
•
interface
Rugged, compact case
•
idth, VPS40 10:1
Technical Specifications 190C and 190B Series
Oscilloscope Mode
Vertical Deflection
Fluke 199C Fluke 196C
Bandwidth 200 MHz 100 MHz 60 MHz
Rise time 1.7 ns 3.5 ns 5.8 ns
Bandwidth limiter: User selectable: 10 kHz, 20 MHz
or off
Number of inputs: 2 plus external trigger. All inputs
isolated from each other and ground.
Input coupling: AC or DC, with ground level indicator
Input sensitivity: 2 mV/div to 100 V/div (Fluke 190C
Series); 5 mV/div to 100 V/div (Fluke 190B Series)
Normal/Invert: On both input channels; switched
separately
Variable attenuator: Variable gain on input channel A
Input voltage: 1000 V CAT II, 600 V CAT III rated -
See “general specifications” for further details.
Vertical resolution: 8 bit
Accuracy: ± (1.5% of reading + 0.04 x range/div)
Input impedance: 1 MΩ ± 1% // 15 pF ± 2 pF
Horizontal
Maximum 2.5 GS/s 1 GS/s 500 MS/s
real-time
sample rate
Number of 2 2 2
digitizers
Time base 5 ns/div 10 ns/div
range to 5 s/div to 5 s/div
Maximum record length: 3000 points per input in
Scope-mode; 27,500 points per input in
ScopeRecord
Accuracy: ± (0.01 % of reading + 1 pixel)
Glitch capture: 50 nsec (at 5 µsec/div to 1 min/div);
250 nsec (at 2 min/div)
Display and Acquisition
Display 144 mm 144 mm
Display modes Input A, Input B, dual, average, Replay
Persistence Digital Persistence: Persistence
modes short/medium/long/infinite on / off
Visible screen width: 12 divisions
Waveform mathematics: A + B, A - B, A * B, all
with user selectable scaling of resultant; A versus B
(X - Y-mode); Frequency Spectrum using FFT analysis
(190C only)
Acquisition modes: Normal, auto, single shot,
ScopeRecord
compare, waveform compare with automatic
“Pass / Fail testing” (in 199C and 196C only)
Trigger and Delay
Source: Input A, input B, external trigger input.
All input references isolated from each other and
from ground
Modes: Automatic Connect-and-View,
single shot, edge, delay, video, video line, selectable
pulsewidth, dual slope (190C only), N-cycle (190C
only)
Fluke 199B Fluke 196B Fluke 192B
Fluke 199C Fluke 196C
Fluke 199B Fluke 196B Fluke 192B
™ roll mode (5 ms/div to 2 min/div)
Fluke 190C Fluke 190B
Full Color LCD Monochrome LCD
™ roll, glitch capture, waveform
™
free run,
Connect-and-View
™
: Advanced automatic triggering
that recognizes signal patterns, automatically sets up
and continuously adjusts triggering, time base and
amplitude. Automatically displays stable waveforms of
complex and dynamic signals like motor drive and
control signals.
Video triggering: NTSC, PAL, PAL+, SECAM. Includes
field 1, field 2 and line select.
Pulse width triggering: Pulse width qualified by time.
Allows for triggering <t, >t, =t, ≠t, where t is selectable in minimal steps of 0.01 div. or 50 nsec.
Time delay: One full screen of pre-trigger view or up
to 100 screens (= 1200 divisions) of post-trigger delay
Dual slope triggering: Both rising and falling transitions, when crossing the trigger level, initiate an
acquisition (190C only)
N-cycle triggering: Triggers on N-th occurrence of a
trigger event; N to be set in the range 2 to 99 (190C
only)
Automatic Capture of 100 Screens
The instrument ALWAYS memorizes the last 100
screens (no user setup required). When an anomaly
occurs on screen, the REPLAY button can be pressed
to review the full screen sequence over
and over.
Instrument can be set up for triggering on glitches
or intermittent anomalies and will operate in
“baby-sit” mode and will capture 100 events.
Alternatively, the 199C and 196C can be set up in
waveform compare mode to store only matching
(“Pass”) or only non-matching (“Fail”) acquired waveforms in the replay memory bank for further analysis.
Replay: Manual or continuous replay. Displays the
captured 100 screens as a “live” animation or under
manual control. Each screen has date- and time-stamp.
Replay storage: Up to 2 sets of 100 screens each
can be saved for later recall and analysis
FFT - Frequency Spectrum Analysis
(190C only)
Shows frequency content of oscilloscope waveform
using Fast Fourier Transform
Window: Automatic, Hamming, Hanning or None
Automatic window: Digitally re-samples acquired
waveform to get optimum frequency resolution in FFT
resultant
Vertical scale: Linear / Logarithmic, in volts
Frequency axis: Logarithmic; frequency range auto-
matically set as function of timebase range of oscilloscope
Waveform Compare and Pass/Fail Testing
Waveform compare: Provides storage and display of a
reference waveform for visual comparison with newly
acquired waveforms. Reference is derived from an
acquired waveform and can be modified in the
ScopeMeter or externally using FlukeView
Pass/Fail Testing (199C, 196C): In waveform compare
mode, the Color Scopemeter can be set up to store
only matching (“Pass”) or only non-matching (“Fail”)
acquired waveforms in the replay memory bank for
further analysis.
®
Software.
2 Fluke Corporation ScopeMeter 190C/190B Series and ScopeMeter 120 Series
Automatic Scope Measurements
Vdc, Vac rms, Vac+dc, Vpeak max, Vpeak min, Vpeak to
peak, Aac, Adc, Aac+dc, frequency (Hz), risetime, falltime, power factor, Watts, VA, VA reactive, phase, pulse
width (pos/neg), dutycycle (pos/neg), temperature °C,
temperature °F, dBV, dBm into 50 Ω and 600 Ω
Vpwm ac, Vpwm ac+dc for measurement on pulse
width modulated motordrives and frequency inverters
Cursor Measurements
Source: Input A, input B or the Mathematical Result
trace (excl. A vs B curve)
Dual horizontal lines: Voltage at cursor 1 and 2,
voltage between cursors
Dual vertical lines: Time between cursors, 1/T
between cursors (in Hz), voltage between markers,
risetime with markers, falltime with markers; Vrms
between cursors (190C only), watts between cursors
(190C only)
Single vertical line: Min-Max and Average voltage
at cursor position; frequency and rms-value of individual frequency component in FFT result (190C only)
Zoom: Up to 16x horizontal zoom
Recorder Mode
ScopeRecord-Roll Mode
Dual input waveform storage mode
Source and display: Input A, Input B, Dual
Memory depth: 27,500 points per input. Each point
consists of Min-Max pair
Min-Max values: Min-Max values are measured at
high sample rates ensuring capture and display of
glitches
Time base range 5 ms/div to 1 min/div 2 min/div
Recorded timespan 6 sec to 24 hr 48 hr
Glitch capture 50 ns 250 ns
Sample rate 20 MS/s 4 MS/s
Resolution 200 µsec to 2 sec 4.8 sec
Recording modes: Single sweep, continuous roll,
Start-on-Trigger, Stop-on-Trigger
Stop-on-Trigger (through external): ScopeRecord
mode can be stopped by an individual trigger event, or
by an interruption of a repetitive trigger signal
Horizontal scale: Time from start, time of day
Zoom: Up to 100x
Memory: Up to 2 dual input ScopeRecord waveforms
can be saved for later recall and analysis
TrendPlot™recording
Single or dual input electronic paperless chart recorder.
Plots, displays and stores meter and scope measurements.
Source and display: Input A, Input B or DMM input
Memory depth: 18,000 points recording. Per record
point a minimum, a maximum and an average value,
plus a date and timestamp are recorded.
Ranges: 5 s/div to 30 min/div in normal view mode;
5 min/div to 48 hr/div in view all mode, giving
overview of total record
Recorded timespan: Up to 22 days with a resolution
of 1 minute
Recording mode: Continuous roll for the duration of
the full recordable timespan
Measurement speed: 5 measurements per second
Horizontal scale: Time from start, time of day
Zoom: Up to 64x zoom
Memory: Up to 2 TrendPlot recordings can be saved
for later recall and analysis
Cursor measurements - all recorder modes
Source: Input A, B or DMM input
Dual vertical lines: Min-Max or Average
voltage. Time between cursors
Single vertical line: Min-Max or Average
voltage. Absolute date and time or time from start
Meter Mode
Via 4 mm banana inputs. Fully isolated from scope
inputs and scope ground. The specified accuracy is
valid over the temperature range 18 °C to 28 °C
(65 °F to 82 °F). Add 10 % of specified accuracy for
each degree C below 18 °C or above 28 °C.
Maximum Resolution: 5,000 counts
Voltmeter Ranges: 500 mV, 5 V, 50 V, 500 V, 1,000 V
Accuracy:
Vdc ± (0.5 % + 5 counts)
Vac true rms
15 Hz...60 Hz: ± (1 % + 10 counts)
60 Hz...1 kHz: ± (2.5 % + 15 counts)
Vac+dc true rms
dc...60 Hz: ± (1 % + 10 counts)
60 Hz...1 kHz: ± (2.5 % + 15 counts)
Ohms:
Ranges: 500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 30 MΩ
Accuracy: ± (0.6 % + 5 counts)
Other Meter Functions
Continuity: Beeper on < 50 Ω (± 30 Ω)
Diode test: Up to 2.8 V
Amps: Adc, Aac, Aac+dc using an optional current
clamp or shunt. Scaling factors: 0.1 mV/A ... 100 V/A
Temperature (°C, °F): With optional accessories. Scale
factors 1 mV/°C or 1 mV/°F
Input impedance: 1 MΩ ± 1% // 10 pF ± 2 pF
Advanced meter functions: Auto/manual ranging,
relative measurements (Zero reference), TrendPlot
recording
ScopeMeter 190C/190B Series and ScopeMeter 120 Series Fluke Corporation 3
General Specifications
Memory Save and Recall
Scope memories: 10 memory locations that each can
contain two waveforms plus corresponding setup
Recorder memories: 2 memory locations that each
can contain 100 captured dual input scope screens, or
a dual input ScopeRecord (27,500 Min-Max pairs per
input), or a dual input Trendplot (18,000 min-max
pairs + average values)
Real-Time Clock
Time and date stamp for ScopeRecord, 100 captured
screens and TrendPlots
Mechanical Data
Size: 256 x 169 x 64 mm (10.1 x 6.6 x 2.5 in)
Weight: 2 kg (4.4 lbs)
Case
Design: Rugged, shock proof with integrated
protective holster
Drip and dust proof: IP51 according to IEC529
Shock and Vibration: Shock 30 g, Vibration
(sinusoidal) 3 g according to MIL-PRF-28800F Class 2
Display Bright full-color LCD Bright LCD
Brightness 80 Cd/m
Display size: 115.2 x 86.4 mm (4.54 x 3.4 in.)
Resolution: 320 x 240 pixels
Contrast and brightness: User adjustable,
temperature compensated
Power
Line power: Country specific line voltage
adapter/battery charger included
Battery power: Rechargeable NiMH (installed)
Battery operating time: 4 hours
Battery charging time: 4 hours
Battery power saving functions: Auto power down
with adjustable power down time. On screen battery
status indicator
Fluke 190C Fluke 190B
with backlight, with backlight
2
using power adapter using power adapter
typ. 125 Cd/m2typ.
Safety
Compliance:
EN61010-1 (2nd Edition) Pollution degree 2
UL 3111-1
CAN/CSA C22.2 No.1010 .1
ANSI/ISA S82.01
Input Voltage Ratings
Maximum probe voltage: 1,000 V CAT II/600 V CAT III
(Maximum voltage between 10:1 probe tip (VPS200)
and reference lead)
Floating voltage: 1,000 V CAT II/600 V CAT III
(Maximum voltage between earth ground and any
terminal (signal input or shielding))
Independently isolated inputs:
1,000 V CAT II/600 V CAT III
(Maximum voltage between any terminal of one input
or probe (VPS200) and any other terminal of another
input or probe (VPS200))
Maximum voltage on BNC input directly
(input A or B): 300 V CAT III
Maximum voltage on meter input:
1,000 V CAT II/600 V CAT III
Environmental
Operating temperature: 0 °C to +50 °C
Storage temperature: -20 °C to +60 °C
Humidity:
10 °C to 30 °C: 95% RH non condensing
30 °C to 40 °C: 75% RH non condensing
40 °C to 50 °C: 45% RH non condensing
Maximum operating altitude: 3,000 m (10,000 feet)
Maximum storage altitude: 12 km (40,000 feet)
Electro-Magnetic-Compatibility (EMC): EN 61326-1
for emission and immunity
Optically Isolated PC / Printer Interface
PC communication: Transfer instrument settings,
screen images, waveform data and waveform
references, compatible with FlukeView
for Windows
®
via optional PM9080.
®
software
To printer: Supports HP Laserjet®, DeskJet, Epson
FX/LQ, Seiko DPU-414 and Postscript printers via
optional PAC 91
Warranty
3 years, parts and labor on mainframe instrument
1 year on accessories
Accessories
Standard Accessories Fluke 199C, Fluke 196C, Fluke 199B, Fluke 196B, Fluke 192B
Rechargeable battery pack (installed) BP190
Line voltage adapter / Battery charger BC190
Voltage probes and accessories 10:1 voltage probe (VPS200, 1 red + 1 grey) including hook clip, ground lead with mini alligator clip, ground lead with
Multimeter test leads TL75 Hard Point test lead set (1red, 1 black)
User manual 10 language versions on CD-ROM, “Getting Started” booklet included with instrument
4 Fluke Corporation ScopeMeter 190C/190B Series and ScopeMeter 120 Series
hook clip, 4 mm add-on probe tip, ground lead to 4 mm banana plug
Technical Specifications
ScopeMeter 120 Series
Oscilloscope Mode
Vertical deflection
Bandwidth and Risetime Fluke 124 Fluke 123
Bandwidth (risetime)
with VPS40 probes 40 MHz 20 MHz
•
input A and B directly 40 MHz 20 MHz
•
with STL120 Shielded Test Leads 12.5 MHz 12.5 MHz
•
Instrument risetime (input directly) 8.75 ns 17.5 ns
Number of inputs: 2
Input coupling: AC, DC with ground level indicator
Input sensitivity: 5 mV to 500 V/div (with the
included VPS40 (Fluke 124) and STL120 shielded test
leads measure up to 600 Vrms, CAT III)
Input voltage: 600 V CAT III. See General Specifications for more detailed information
Vertical resolution: 8 bit
Accuracy: ± (2 % of reading + 0.05 x range/div)
Input impedance: 1 MΩ ±1 % // 225 pF with STL120
shielded test leads; 1 MΩ ±1 % // 20 pF ± 3 pF with
BB120; 5 MΩ ±1 % // 15.5 pF with VPS40, 10:1 Voltage probe
Horizontal
Max. sample rate (both channels simultaneously):
Fluke 124: 2.5 GS/s for repetitive signals; 25 MS/s for
single shot
Fluke 123: 1.25 GS/s for repetitive signals; 25 MS/s
for single shot
Number of digitizers: 2
Time base range: 10 ns/div to 1 min/div (Fluke 124);
20 ns/div to 1 min/div (Fluke 123)
Maximum record length: 512 Min-Max points
per input
Accuracy: ± (0.1 % of reading + 1 pixel)
Glitch detect: 40 ns
Display and acquisition
Display modes: Input A, input A and B, envelope,
smooth
Acquisition modes: Normal (including glitch capture),
single shot, roll
Trigger and delay
Source: Input A, input B, external via optional ITP120
Modes: Automatic Connect-and-View, Free Run, Edge,
Single Shot, Video, Video Line
Connect-and-View: Advanced automatic triggering
that recognizes signal patterns and automatically sets
up and continuously adjusts triggering, time base and
amplitude. Automatically displays stable pictures of
complex and dynamic signals like motor drive and
control signals
Video triggering: NTSC, PAL, PAL+, SECAM. Includes
line select
Time delay: Up to 10 divisions pre-trigger view
Measurements
Vdc, Vac, Vac+dc, Vpeak max, Vpeak min, Vpeak
to peak, frequency (Hz), positive pulse width, negative
pulse width, positive duty cycle, negative duty
cycle, Amp ac, Amp dc, Amp ac+dc, Phase,
Temperature °C, Temperature °F, dBV, dBm into 50 Ω
and 600 Ω. (Amps, °C or °F with optional probes)
Cursor Measurements (124 only)
Sources: Input A, Input B
Modes: Single or dual vertical cursor, dual horizontal
cursor, rise- or falltime
Measurements:
Single vertical line: Average, min value, max value,
time from start of recording in roll mode
Dual vertical lines: ∆V at markers, time between
cursors, 1/T between cursors (in Hz)
Dual horizontal lines: High, low or ∆V - readout,
rise- and falltime: transition time, 0 %-level, 100 %level, with markers at 10 % and 90 %
Accuracy: As oscilloscope
Dual Input Meter
The specified accuracy is valid over the temperature
range 18 °C to 28 °C (64 °F to 82 °F). Add 10 % of
specified accuracy for each °C below 18 °C or above
28 °C (64 °F to 82 °F)
Max. meter bandwidth: 40 MHz (Fluke 124),
20 MHz (Fluke 123)
Voltage measurements
Measurement selection: Vdc, Vac rms, Vac+dc rms,
Vpeak max, Vpeak min, V
Ranges: 500 mV, 5 V, 50 V, 500 V, 1250 V
Full scale reading: 5,000 counts
Accuracy
Vdc: ± (0.5 % + 5 counts)
Vac rms:
1 Hz to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)
20 kHz to 1 MHz ± (5 % + 20 counts)
Vac+dc true-rms:
DC to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)
20 kHz to 1 MHz (5 % + 20 counts)
Vpeak:
Max peak or Min peak: 5% of full scale
Peak-to-peak: 10% of full scale
Ohms
Ranges: 500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 30 MΩ
Max. resolution: 5,000 counts
Accuracy: ± (0.6 % of reading + 5 counts)
Capacitance
Ranges: 50 nF to 500 µF
Max. resolution: 5,000 counts
Accuracy: ± (2 % of reading + 10 counts)
Other meter functions
Frequency: Up to 70 MHz (Fluke 124) or up to 40 MHz
(Fluke 123)
Continuity: Beeper on < 30 Ω
Diode test: Up to 2.8 V
Amps: Amp dc, Amp ac, Amp ac+dc using an optional
current clamp or shunt. Scaling factors: 0.1 mV/Amp to
100 V/Amp
Temperature (°C, °F): With optional accessories. Scale
factors 1 mV/°C or 1 mV/°F
Number of inputs: 2
Input impedance: 1 MΩ ± 1 % // 10 pF ± 2 pF
Advanced meter functions: Auto/manual ranging,
TouchHold
TrendPlot recording
®
, Relative measurements (zero reference),
ScopeMeter 190C/190B Series and ScopeMeter 120 Series Fluke Corporation 5
pk-pk
Recorder Mode
Trendplot recording
Dual input electronic paperless chart recorder. Plots
and displays the actual, minimum, maximum and
average of any measurement.
Source and display: Input A, Input A and B
Range: 15 s/div to 2 days per division (automatic)
Recorded timespan: Up to 16 days with a resolution
of 1.5 hours
Recording mode: Continuous with automatic vertical
scaling and horizontal time compression
Measurement speed: 2.5 measurements per second
maximum
Horizontal scale: Time from start
General Specifications
Case
Design: Rugged, shock proof with integrated
protective holster
Drip and dust proof: IP51 according to IEC529
Shock and vibration: Shock 30 g Vibration 3 g
(sinusoidal) according to MIL-PRF-28800F Class 2
Display
Bright LCD with CCFL backlight, 60 (35) cd/m
with (without) power adapter
Size: 72 x 72 mm (2.8 x 2.8 inch)
Resolution: 240 x 240 pixels
Contrast and brightness: User adjustable,
temperature compensated
Memory Save and Recall
20 (10 in Fluke 123) instrument screens with user
set-ups and user text
Real-time clock
Time and date stamp TrendPlot recording
Power
Line power: Country specific line voltage
adapter/battery charger included
Battery power: Rechargeable Ni-MH BP130 (installed
in Fluke 124) or rechargeable NiCd BP120 (installed in
Fluke 123)
Battery operating time: Up to 7 hours using BP130,
up to 5 hours using BP120
Battery charging time: 5 hours (Fluke 123), 7 hours
(Fluke 124)
Battery power saving functions: Auto power down
with adjustable power down time. On-screen battery
power indicator
2
Mechanical data
Size: 50 x 115 x 232 mm (2 x 4.5 x 9.1 in)
Weight: 1.2 kg (2.64 lbs)
Safety
Compliance: EN61010.1 (2nd Edition) Pollution degree
2, UL3111-1, CAN/CSA-C22.2 No. 1010.1,
ANSI/ISA S82.01
Input voltage ratings
Maximum input voltage: 600 V CAT III
(Maximum voltage between input and reference lead)
Maximum input voltage using VPS40 Probe: 600 V
CAT III, 1000 V CAT II (Maximum voltage between
probe tip input and reference lead)
Floating voltage: 600 V CAT III
(Maximum voltage between earth ground and any
terminal (signal input or reference lead))
Maximum voltage between reference leads:
Instrument has common grounds connected via
self recovering fault protection. For different ground
potential measurements between inputs use DP120
differential voltage probe
Environmental
Operating temperature: 0 °C to +50 °C
Storage temperature: -20 °C to +60 °C
Humidity:
10 °C to 30 °C, 95% RH non condensing;
30 °C to 40 °C, 75% RH non condensing;
40 °C to 50 °C, 45% RH non condensing
Maximum operating altitude: 2,000 m (6,500 feet);
3,000 m (10,000 feet) voltages ≤ 400 V
Maximum storage altitude: 12 km (40,000 feet)
Electro-Magnetic Compatibility:
Emission EN50081-1 (EN55022 and EN60555-2)
Immunity EN50082-2 (IEC1000–4-2, -3, -4, -5)
Optically isolated PC/Printer interface
To printer: Supports HP Laserjet,®Deskjet,®Epson
FX/LQ and postscript printers via optional PAC91
To PC: Transfer instrument settings, screen images
and data, compatible with FlukeView
Windows®via optional PM9080
®
software for
Warranty
3 years, parts and labor on mainframe instrument
1 year on accessories
Accessories
Standard Accessories Fluke 123, Fluke 124
Rechargeable battery pack (installed) BP120 (Fluke 123)
Line voltage adapter / Battery charger PM8907
Voltage probes and accessories STL120 Shielded Test lead set; VPS40 high impedance 10:1 probe, 40 MHz (1 black, included with Fluke 124 only);
Multimeter test leads TL75 Hard Point test lead (1 black)
User manual 15 language versions on CD-ROM, “Getting Started” booklet included with instrument
6 Fluke Corporation ScopeMeter 190C/190B Series and ScopeMeter 120 Series
HC120 hook clips; ground leads with mini alligator clips; AC120 alligator clips; BB120 BNC-to-Shielded banana adapter
BP130 (Fluke 124)
International Safety Standards
Measurement
Voltage
Category Summary description
CAT IV Three phase at utility connection, any outdoors
CAT III Three-phase distribution (under 1,000 V),
CAT II Single-phase receptable connected loads
CAT I Electronic
conductors (under 1,000 V)
• Outside and service entrance
• Service drop from pole to building
Run between meter and panel
•
Overhead line to detached building
•
• Underground line to well pump
including single phase commercial lighting
and distribution panels
• Feeders and short branch circuits
Distribution panel devices
•
• Heavy appliance outlets with “short”
connections to service entrance
• Outlets and long branch circuits
• All outlets at more than 10 m (30 ft)
from Categor
All outlets at more than 20 m (60 ft)
•
from Category IV source
• Electronic equipment
• Low energy equipment with transient
limiting protection
y III source
To protect your instrument and – more importantly –
yourself, choose a test tool that can withstand the
electrical hazards present in the environment in which
you plan to use it.
EN61010 establishes international safety requirements for electrical measurement equipment. It
separates the various electrical environments into
installation categories based on the danger from high
voltage-energy transients. To choose the right tool,
the voltage rating alone does not determine the
safety. It is the combination of voltage rating and
installation category that determines maximum transient withstand capability of the tool. CAT III rated
instruments are recommended for measurement on
industrial power distribution systems.
FlukeView®ScopeMeter®Software for Windows
FlukeView software adds PC power to your
Fluke ScopeMeter Test Tools.
FlukeView ScopeMeter software helps you get more
out of your ScopeMeter:
Store instrument’s screen copies on the PC, in c
•
(with Fluke 1
(Fluke 190B and 120 Series)
Copy color screen images into your reports and
•
documentation (color screen images with Fluke
190C Series only)
Capture and store waveform data from your
•
ScopeMeter on your PC
Create and archive waveform references for auto-
•
matic (Fluke 190C Series) or visual (Fluke 190B and
190C Series) comparison
Use cursors for parameter measurement
•
Includes waveform analysis, e.g., FFT spectrum
•
analysis
Copy waveform data into your spreadsheet for
•
detailed analysis
Extended recording of up to four user-selected
•
measurements help you monitor and analyze slow
moving signals and related events
Logging of other readings directly into other appli-
•
cation programs, eg., spreadsheet
90C Series) or in black and white
olor
Add user text to instrument setups and send
•
these to the instrument for operator reference and
instructions
Capture complete Replay sequence into the PC for
•
further analysis and documentation
English, French and German versions included on a
•
single CD-ROM
Note: Some functionality may be
available with specific ScopeMeter
models only
System requirements
Pentium 90 or better
•
CD-ROM drive
•
Windows®95 / 98 / Me /
•
NT 4.0 / 2000 / XP
One free RS 232 port
•
PM9080 Optically isolated
•
RS 232 adapter/cable,
available separately or
included in
SCC190/SCC120 kit and in
ScopeMeter ‘S’ versions
Supported Instruments
Full support for Fluke 199C, 199B, 199, 196C, 196B,
196, 192B, 192, 124, 123
®
ScopeMeter 190C/190B Series and ScopeMeter 120 Series Fluke Corporation 7
Selection Guide
190C Color ScopeMeter Series 190B ScopeMeter Series 120 ScopeMeter Series
Bandwidth 200 MHz 100 MHz 200 MHz 100 MHz 60 MHz 40 MHz 20 MHz
Max real time sample rate 2.5 GS/s 1 GS/s 2.5 GS/s 1 G S/s 500 MS/s 25 MS/s 25 MS/s
Max equivalent time
sample rate
Display 144 mm full color LCD 144 mm monochrome LCD 102 mm monochrome LCD
Digital persistence Yes, gives analog oscilloscope like
Envelope mode Yes Yes Yes
Waveform compare Visual reference and automatic Visual reference —
FFT analysis Windowing: Auto, Hamming,
Max record length
in Scope Mode: 3000 points per input channel
in ScopeRecord mode: 27,000 points per input or more (5 ms/div to 2 min/div)
Number of inputs 2 plus external / DMM input, all isolated from each other and from ground 2
Number of digitizers 2 2
Independently floating
isolated inputs
Input sensitivity 2 mV/div to 100 V/div 5 mV/div. to 100 V/div 5 mV/div to 500 V/div
Glitch capture
Timebase range in
Scope mode
Trigger types Connect-and-View™, Free Run, Single Shot, Edge, Delay, Video Frame, Video Line Connect-and-View™, Free Run,
Scope measurements
Waveform mathematics A + B, A - B, A x B, A versus B (X-Y-mode, giving Lissajous diagrams)
ScopeRecord trigger modes Start on trigger, stop on trigger, stop in absence of trigger signal —
Capture last 100 screens Automatic, with replay capability —
Dual input TrendPlot Yes, with cursors and zoom Yes
Memory for screens and 10 screens with set-up;
set-ups 5 more memories are made available upon registration of the ScopeMeter
Memory for recordings Two, each can store 100 scope screens, a ScopeRecord or a TrendPlot
True-rms multimeter 5000 counts, Volts, Amps, Ohms, Continuity, Diode, Temp
Safety certified 1000 V CAT II / 600 V CAT III (instrument and included accessories) 600 V CAT III (instrument and
(EN61010-1) included accessories)
Battery (installed) 4 hr Ni-MH BP190 7 hr NiMH 5 hr NiCd
Line Power Adapter / battery-charger included
Size 25 x 16.9 x 6.4 mm (10.1 x 6.7 x 2.5 in) 232 x 115 x 50 mm (9.2 x 4.5 x 2 in)
Weight 2 kg (4.4 lb) 1.2 kg (2.64 lbs)
PC and Printer Interface Using optional optically isolated RS-232 adapter/cable
Warranty 3 years on main instrument, 1 year on the standard accessories
Fluke 199C Fluke 196C Fluke 199B Fluke 196B Fluke 192B Fluke 124 Fluke 123
— — — — — 2.5 G S/s 1.25 GS/s
waveform decay (user selectable)
‘Pass / Fail’ testing
Hanning or none
Up to 1000 V between inputs, references and ground —
Up to 3 ns using pulse width triggering; 50 ns peak detect at 5 ms/div to 1 min/div
5 ns/div to 2 min/div 10 ns/div to 10 ns/div to 20 ns/div to
Selectable pulse width and external Single Shot, Edge, Video
N-Cycle, Dual Slope — —
7 cursor measurements, 30 automatic measurements
+ Automatic Vrms and watts cursors + 26 26 automatic
measurement on cursor limited —
part of waveform measurements
+ Frequency Spectrum (FFT) —
Detailed technical specifications, optional accessories and a virtual product demo can be
found on the Fluke web site. Check it out at: www.fluke.com/scopemeter.
——
——
512 min/max points per input
40 ns
2 min/div 1 min/div 1 min/div
automatic measurements
—
20 10
Ordering Information
Fluke-199C
Fluke-199C Color ScopeMeter (200 MHz / 2.5 GS /s)
Fluke-196C/S Color ScopeMeter (100 MHz / 1 GS/s)
Fluke-196C Color ScopeMeter (100 MHz / 1 GS/s)
Fluke-199B/S ScopeMeter (200 MHz / 2.5 GS/s) with
Fluke-199B ScopeMeter (200 MHz / 2.5 GS /s)
Fluke-196B/S
Fluke-196B ScopeMeter (100 MHz / 1 GS/s)
Fluke-192B/S ScopeMeter (60 MHz / 500 MS/s) with
Fluke-192B ScopeMeter (60 MHz / 500 MS/s)
Fluke-124/S Industrial ScopeMeter, 40 MHz, with
Fluke-124 Industrial ScopeMeter, 40 MHz
Fluke-123/S Industrial ScopeMeter, 20 MHz, with
Fluke-123 Industrial ScopeMeter, 20 MHz
BP120 Rechargeable NiCd Battery for use with
/S Color ScopeMeter (200 MHz / 2.5 GS/s)
with SCC190 kit
with SCC190 kit
SCC190 kit
ScopeMeter (100 MHz / 1 GS/s) with
SCC190 kit
SCC190 kit
SCC120 kit
SCC120 kit
Fluke 120 Series
BP130 Rechargeable NiMH Battery for use with
BP190 Rechargeable NiMH Battery for use with
SW90W FlukeView ScopeMeter Software for
PM90
SCC190 Software - Cable - Case kit for Fluke
SCC120 Software - Cable - Case kit for Fluke
C195 Durable, universal soft carrying case for
C190 Hard shell protective carrying case for
C125 Durable, protective soft carrying case for
C120 Hard shell protective carrying case for
DP120 Differential Voltage Probe for use with
VPS40 40 MHz, 10:1 Voltage probe set for use
Fluke 120 Series
Fluke 190 Series ScopeMeters
Windows
80 Optically isolated RS232 adapter/cable
90 Series
1
120 Series
ScopeMeters and accessories
Fluke 190 Series ScopeMeters
Fluke 120 Series ScopeMeters
Fluke 120 Series ScopeMeters
Fluke 120 Series
with Fluke 120 Series
Fluke. Keeping your world
up and running.
Fluke Corporation
PO Box 9090, Everett, WA USA 98206
Fluke Europe B
PO Box 1186, 5602 BD
Eindhoven, The Netherlands
For mor
In the U.S.A. (800) 443-5853 or
Fax (425) 446-5116
In Europe/M
Fax +31 (0) 40 2675 222
In Canada (800)-36-FLUKE or
Fax (905) 890-6866
From other countries (425) 446-5500 or
Fax (425) 446-5116
Web access: http://www.fluke.com/
©2004 Fluke Corporation. All rights reserved.
Trademarks are the property of their respective owners.
Printed in U.S.A. 3/2004 1629083 D-ENG-N Rev D
.V.
e information call:
-East/Africa +31 (0) 40 2675 200 or
Loading...