Fluke 192 Data Sheet

ScopeMeter® 190 Series

ScopeMeter 123

ScopeMeter 190 Series: Speed,
performance and analysis power

For demanding applications, the ScopeMeter
190 Series high-performance oscilloscopes offer
specifications usually found on top-end bench
instruments. With up to 200 MHz bandwidth,

2.5 GS/s real-time sampling and a deep memory
of 27,500 points per input, they’re ideal for
engineers who need the full capabilities of a
high-performance scope in a handheld, battery
powered instrument.

✓

Dual input - 60, 100 or 200 MHz bandwidth

✓

Up to 2.5 GS/s real-time sampling per input

✓

Connect-and-View™ automatic triggering,
a full range of manual trigger modes plus
external triggering

✓

27,500 points per input record length using
ScopeRecord™ mode

✓

Automatic capture and replay of 100 screens

✓

24 automatic waveform measurements

✓

Cursors, zoom and real-time clock

✓

Four hours rechargeable NiMH battery pack

✓

1,000V CAT II and 600V CAT III safety
certified

✓

Up to 1,000V independently floating isolated
inputs

✓

Includes a 5,000 counts True-rms multimeter
and a TrendPlot™ paperless recorder

E

G

M

A

E

N

N

A

T

M

S

L

A

U

Q

C

E

R

T

I

Y

T

I

F

I

LISTED

Y

S

T

E

M



1

0

0

9

E

O

S

I

D

T

T

E

O

E

M

ScopeMeter 123:
Three-in-one simplicity

The compact ScopeMeter 123 is the rugged solu­tion for industrial troubleshooting and installation
applications. It’s a truly integrated test tool, with
oscilloscope, multimeter and “paperless” recorder
in one affordable, easy-to-use instrument. Find
fast answers to problems in machinery, instru­mentation, control and power systems.

✓

A dual input 20 MHz digital oscilloscope

✓

Two 5,000 counts True-rms digital
multimeters

✓

A dual input TrendPlot™ recorder

✓

Connect-and-View™ trigger simplicity for
hands-off operation

✓

Shielded test leads for oscilloscope, resistance
and continuity measurements

✓

Up to five hours battery operation

✓

600V CAT III safety certified

✓

Optically isolated RS-232 interface

✓

Rugged compact case

Technical Data

R

Technical Specifications

ScopeMeter 190 Series

Oscilloscope Mode

Vertical deflection

Fluke 199 Fluke 196 Fluke 192

Bandwidth 200 MHz 100 MHz 60 MHz
Rise time 1.7 ns 3.5 ns 5.8 ns

Bandwidth limiter: User selectable 10 kHz or 20 MHz
Number of inputs: 2 plus external trigger. All isolated

from each other and ground.

Input coupling: AC, DC with ground level indicator
Input sensitivity: 5 mV/div to100 V/div
Input voltage: See general specifications for maximum

rating

Vertical resolution: 8 bit
Accuracy: ±(1.5% of reading + 0.04 x range/div)
Input impedance: 1 MΩ ± 1% // 15 pF ± 2 pF

Horizontal

Fluke 199 Fluke 196 Fluke 192

Maximum
real-time 2.5 GS/s 1 GS/s 500 MS/s
sample rate

Number of
digitizers

Time base 5 ns/div 10 ns/div
range to 5 s/div to 5 s/div

Maximum record length: 1,000 points per input

27,500 points per input in ScopeRecord
(10 ms/div ... 2 min/div)

Accuracy: ± (0.01% of reading + 1 pixel)
Glitch capture: 50 nsec (5 µsec/div to 1 min/div)

Faster time bases have higher sample rates than
20 MS/s

Display and acquisition

Display modes: Input A, input B, dual, average, per­sistence, invert, replay
Acquisition modes: Normal, auto, single shot,
ScopeRecord,

222

™

-roll mode

™

roll, glitch capture

Trigger and delay

Source: Input A, input B, external trigger input. All
input references isolated from each other and ground.
Modes: Automatic Connect-and-View,

™

free run, single
shot, edge, delay, video, video line, selectable pulse
width

Connect-and-View

™

: Advanced automatic triggering
that recognizes signal patterns, automatically sets up
and continuously adjusts triggering, time base and
amplitude. Automatically displays stable waveforms of
complex and dynamic signals like motor drive and
control signals.
Video triggering: NTSC, PAL, PAL+, SECAM. Includes
field 1 and 2 and line select.
Pulse width triggering: Pulse width qualified by time.
Allows for triggering <t ,>t, = t, ≠t, where t is select­able in minimal steps of 0.01 div or 50 nsec.
Time delay: 9 divisions pre-trigger view to 1,000
divisions trigger delay

Automatic capture of 100 screens

The instrument ALWAYS memorizes last 100 screens
(no user interaction or setup required). When an
anomaly occurs on screen, there’s 10 seconds to press
HOLD and review it. If one sets up the instrument for
triggering on glitches or intermittent anomalies the
unit operates in “baby-sit” mode and will capture 100
events.
Replay: Manual or continuous replay. Displays the
captured 100 screens as a “live” animation. The
contents can also be viewed by manually scrolling
backwards and forwards “screen by screen”.
Replay storage: Up to 2 sets of 100 screens can be
saved for later recall and analysis.

Automatic scope measurements

VDC, VAC rms, VAC+DC, Vpeak max, Vpeak min, Vpeak
to peak, frequency (Hz), positive pulse width, negative
pulse width, positive duty cycle, negative duty cycle,
amp AC, amp DC, amp AC+DC, power factor, watts, VA,
VA reactive, phase, temperature °C, temperature °F,
dBV, dBm into 50Ω and 600Ω

2 Fluke Corporation ScopeMeter 190 Series and ScopeMeter 123

Cursor measurements

Source: Input A or B
Dual horizontal lines: Voltage at cursor 1 and 2,

voltage between cursors
Dual vertical lines: Time between cursors, voltage
between markers
Single vertical line: Min-Max and Average voltage at
cursor position

Zoom

Up to 8x horizontal zoom

Meter Mode

Via 4 mm banana inputs. Fully isolated from scope
inputs and scope ground. The specified accuracy is
valid over the temperature range 18 °C to 28 °C (15 °F
to 33 °F). Add 10 % of specified accuracy for each
degree °C below 18 °C or above 28 °C (15 °F to 33 °F).

Maximum resolution

5,000 counts

Voltmeter ranges

500mV, 5V, 50V, 500V, 1,000V

Accuracy

VDC: ± (0.5 % + 5 counts)
VAC true rms

15 Hz to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)

VAC+DC true rms

DC to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)

Ohms

Ranges: 500Ω, 5kΩ, 50kΩ, 500kΩ, 5MΩ, 30MΩ
Accuracy: ± (0.6 % + 5 counts)

Other meter functions

Continuity: Beeper on < 30Ω (± 10Ω)
Diode test: Up to 2.8V
Amps: Amp DC, Amp AC, Amp AC+DC using an

optional current clamp or shunt. Scaling factors:

0.1 mV/Amp to 100 V/Amp

Temperature (

Scale factors 1 mV/°C or 1 mV/°F

Input impedance: 1 MΩ ± 1% // 10 pF ± 2 pF
Advanced meter functions: Auto/manual ranging,

relative measurements (Zero reference), TrendPlot
recording

°C, °F): With optional accessories.

Recorder Mode

ScopeRecord-roll mode

Dual input waveform storage mode.

Source and display: Input A, Input B, Dual
Memory depth: 27,500 points per input. Each point

consist of Min-Max pair.
Min-Max values: Min-Max values are measured at
high sample rate ensuring capture and display of
glitches

Time base range 10 ms/div to 1 min/div 2 min/div

Recorded timespan 11 sec to 15 hrs 30 hrs
Glitch capture 50 nsec 250 nsec
Sample rate 20 MS/s 4 MS/s
Resolution 400 µsec to 2 sec 4 sec

Recording modes: Single sweep, continuous roll, start
on external trigger

Horizontal scale: Time from start, time of day
Zoom: Up to 100 x zoom
Memory: Up to 2 dual input ScopeRecordings can be

saved for later recall and analysis

TrendPlot™ recording

Dual input electronic paperless chart recorder. Plots,
displays and stores meter and scope measurements.

Source and display: Input A, Input B and DMM input
Memory depth: 13,500 points record per input. Per

record point a minimum, maximum and average value,
and a time and date stamp are stored.
Ranges: 10 s/div to 20 min/div in normal view mode.
10 min/div to 24 hour/div in view-all mode (overview
of total record)
Recorded timespan: Up to 8 days with a resolution of
1 minute

Recording mode: Continuous roll
Measurement speed: 2.5 measurements per second

maximum

Horizontal scale: Time from start, time of day
Zoom: Up to 64x zoom
Memory: Up to 2 TrendPlot recordings can be saved

for later recall and analysis

Cursor measurements - All Recorder Modes

Source: Input A, B or DMM input
Dual vertical lines: Min-Max or Average voltage.

Time between cursors.
Single vertical line: Min-Max or Average voltage.
Absolute date and time or time from start.

ScopeMeter 190 Series and ScopeMeter 123 Fluke Corporation 3

Technical Specifications

ScopeMeter 190 Series

cont.

General Specifications

Case

Design: Rugged, shock proof with integrated
protective holster

Drip and dust proof: IP51 according to IEC529
Shock and vibration: Shock 30g, Vibration 3g

according to MIL 28800F type III, class 3, style B

Display

Bright LCD with CCFL backlight, 35/60 cd/m2 with­out/with power adapter.

Size: 105 x 79 mm (4.1 x 3.1 inches)
Resolution: 240 x 240 pixels
Contrast and brightness: User adjustable,

temperature compensated

Memory Save and Recall

Scope memories: 10 memory locations that each can
contain two waveforms plus corresponding setup.
Recorder memories: 2 memory locations that each
can contain 100 captured dual input scope screens, or
a dual input ScopeRecord (27,500 Min-Max pairs per
input), or a dual input Trendplot (13,500 Min-Max
pairs per input).

Real-time clock

Time and date stamp for ScopeRecord, 100 captured
screens and Trendplots.

Power

Line power: Country specific line voltage adapter/
battery charger included

Battery power: Rechargeable NiMH (installed)
Battery operating time: 4 hours
Battery charging time: 4 hours
Battery power saving functions: Auto power down

with adjustable power down time. On screen battery
power indicator

Mechanical data

Size: 256 x 169 x 64 mm (10.1 x 6.6 x 2.5 inches)
Weight: 1.95 kg (4.3 lbs)

Safety

Compliance: EN61010-1 (1993) Pollution degree 2,
UL 3111-1 (1994), CAN/CSA C22.2 No.1010.1 (1992),
ANSI/ISA S82.01 (1994)

Input voltage ratings

Maximum probe voltage: 1,000V CAT II, 600V CAT III
(Maximum voltage between 10:1 probe tip (VP190)
and reference lead)
Floating voltage: 1,000V CAT II, 600V CAT III
(Maximum voltage between earth ground and any
terminal (signal input or shielding))
Independently isolated: 1,000V CAT II, 600V CAT III
inputs (Maximum voltage between any terminal of
one input or probe (VP190) and any other terminal
of another input or probe (VP190))

Maximum voltage on BNC input directly
(input A or B): 300V CAT III
Maximum voltage on meter input: 1,000V CAT II,

600V CAT III

Environmental

Operating temperature: 0 °C to +50 °C
Storage temperature: -20 °C to +60 °C
Humidity

10 °C to 30 °C: 95% RH non condensing
30 °C to 40 °C: 75% RH non condensing
40 °C to 50 °C: 45% RH non condensing

Maximum operating altitude: 3,000 m (10,000 feet)
Maximum storage altitude: 12 km (40,000 feet)
Electro-Magnetic Compatibility: EN 61326-1 for

emission and immunity

Optically isolated PC/Printer interface

To printer: Supports HP Laserjet,® Deskjet,® Epson FX/
LQ and postscript printers via optional PAC 91
To PC: Transfer instrument settings, screen images
and waveform data, compatible with FlukeView
ware for Windows

®

via optional PM9080.

®

soft-

Warranty

3 years

4 Fluke Corporation ScopeMeter 190 Series and ScopeMeter 123

Technical Specifications

ScopeMeter 123

Oscilloscope Mode

Vertical deflection

Bandwidth: 20 MHz at inputs; 20 MHz with BB120
and optional PM 8918/VP190 10:1 probes; 12.5 MHz
with STL120 1:1 test leads

Rise time: 17.5 ns
Number of inputs: 2
Input coupling: AC, DC with ground level indicator
Input sensitivity: 5 mV to 500 V/div (with included

STL120 shielded test leads measure up to 600 Vrms)

Vertical resolution: 8 bit
Accuracy: ± (2% of reading + 0.05 x range/div)
Input impedance: 1 MΩ ± 1% // 225 pF with STL120

shielded test leads; 1 MΩ ± 1% // 20 pF ± 3 pF with
BB120

Horizontal

Maximum sample rate: 1.25 GS/s for repetitive
signals; 25 MS/s for single shot

Number of digitizers: 2
Time base range: 20 ns/div to 1 min/div
Maximum record length: 512 Min-Max points per input
Accuracy: ± (0.1% of reading + 1 pixel)
Glitch detect: 40 ns

Display and acquisition

Display modes: Input A, input A and B, envelope,
smooth
Acquisition modes: Normal, single shot, roll, glitch
capture (always on)

Trigger and delay

Source: Input A, input B, external via optional ITP120
Modes: Automatic Connect-and-View,

Edge, Single Shot, Video, Video Line

Connect-and-View

that recognizes signal patterns and automatically sets
up and continuously adjusts triggering, time base and
amplitude. Automatically displays stable pictures of
complex and dynamic signals like motor drive and
control signals.
Video triggering: NTSC, PAL, PAL+, SECAM. Includes
line select
Time delay: Up to 10 divisions pre-trigger view

™

: Advanced automatic triggering

Measurements

VDC, VAC, VAC+DC, Vpeak max, Vpeak min, Vpeak to
peak, frequency (Hz), positive pulse width, negative
pulse width, positive duty cycle, negative duty cycle,
Amp AC, Amp DC, Amp AC+DC, Phase, Temperature °C,
Temperature °F, dBV, dBm into 50Ω and 600Ω. (Amps,
°C or °F with optional probes)

™

Free Run,

Dual Input Meter

The specified accuracy is valid over the temperature
range 18°C to 28°C (15°F to 33°F). Add 10 % of speci-
fied accuracy for each degree °C below 18°C or above
28°C (15°F to 33°F).

Max. meter bandwidth: 20 MHz

VDC

Ranges: 500mV, 5V, 50V, 500V, 1,250V
Max. resolution: 5,000 counts
Accuracy: ± (0.5% + 5 counts)

VAC rms

Ranges: 500mV, 5V, 50V, 500V, 1,250V
Max. resolution: 5,000 counts
Accuracy:

1 Hz to 60 Hz: ±(1% + 10 counts)
60 Hz to 1 kHz: ±(2.5% + 15 counts)
20 kHz to 1 MHz (5% + 20 counts)

VAC+DC true rms

Ranges: 500mV, 5V, 50V, 500V, 1,250V
Max. resolution: 5,000 counts
Accuracy:

DC to 60 Hz: ±(1% + 10 counts)
60 Hz to 1 kHz: ±(2.5% + 15 counts)
20 kHz to 1 MHz (5% + 20 counts)

Ohms

Ranges: 500Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 30 MΩ
Max. resolution: 5,000 counts
Accuracy: ± (0.6% of reading + 5 counts)

Capacitance

Ranges: 50 nF to 500 µF
Max. resolution: 5,000 counts
Accuracy: ± (2% of reading + 10 counts)

Other meter functions

Frequency: Up to 40 MHz
Continuity: Beeper on < 30Ω
Diode test: Up to 2.8V
Amps: Amp DC, Amp AC, Amp AC+DC using an op-

tional current clamp or shunt

Scaling factors: 0.1 mV/Amp to 100 V/Amp
Temperature (

factors 1 mV/°C or 1 mV/°F.

Number of inputs: 2
Input impedance: 1 MΩ ± 1% // 10 pF ± 2 pF
Advanced meter functions: Auto/manual ranging,

TouchHold
TrendPlot recording

°C, °F): With optional accessories. Scale

®

, Relative measurements (zero reference),

ScopeMeter 190 Series and ScopeMeter 123 Fluke Corporation 5

Technical Specifications

ScopeMeter 123

cont.

Recorder Mode

Trendplot™ recording

Dual input electronic paperless chart recorder. Plots
and displays the actual, minimum, maximum and
average of any measurement.

Source and display: Input A, Input A and B
Range: 15 s/div till 2 days per division (automatic)
Recorded timespan: Up to 16 days with a resolution

of 1.5 hours
Recording mode: Continuous with automatic vertical
scaling and horizontal time compression
Measurement speed: 2.5 measurements per second
maximum
Horizontal scale: Time from start

General Specifications

Case

Design: Rugged, shock proof with integrated
protective holster

Drip and dust proof: IP51 according to IEC529
Shock and vibration: Shock 30g, Vibration 3g

according to MIL-T28800E, Type III, Class 3, Style B

Display

Bright LCD with CCFL backlight, 35/60 cd/m2 without/
with adapter

Size: 72 x 72mm (2.8 x 2.8 inch)
Resolution: 240 x 240 pixels
Contrast and brightness: User adjustable, temperature

compensated

Memory Save and Recall

2 screens, 10 user setups

Real-time clock

Time and date stamp TrendPlot recording

Power

Line power: Country specific line voltage adapter/
battery charger included

Battery power: Rechargeable NiCd (installed)
Battery operating time: Up to 5 hours
Battery charging time: 4 hours
Battery refresh cycle: 8 to 14 hours depending on

remaining capacity at start of refresh cycle
Battery power saving functions: Auto power down
with adjustable power down time. On screen battery
power indicator.

Mechanical data

Size: 50 x 115 x 232 mm (2 x 4.5 x 9.1 inches)
Weight: 1.2 kg (2.5 lb.)

Safety

Compliance: EN61010.1 (1993) Pollution degree 2,
UL3111-1 (1994), CAN/CSA-C22.2 No. 1010.1 (1992),
ANSI/ISA S82.01 (1994)

Input voltage ratings

Maximum input voltage: 600V CAT III
(Maximum voltage between input and reference lead)
Floating voltage: 600V CAT III
Maximum voltage between earth ground and any
terminal (signal input or reference lead)

Maximum voltage between reference leads:

Instrument has common grounds connected via
self recovering fault protection. For different ground
potential measurements between inputs use DP120
differential voltage probe.

Environmental

Operating temperature: 0°C to +50°C
Storage temperature: -20°C to +60°C
Humidity:

10°C to 30°C, 95% RH non condensing;
30°C to 40°C, 75% RH non condensing;
40°C to 50°C, 45% RH non condensing
Maximum operating altitude: 2,000m (6,500 feet);
3,000m (10,000 feet) voltages ≤ 400V

Maximum storage altitude: 12 km (40,000 feet)
Electro-Magnetic: Emission EN50081-1 (EN55022

and EN60555-2)
Compatibility: Immunity EN50082-2
(IEC1000–4-2, -3, -4, -5)

Optically isolated PC/Printer interface

To printer: Supports HP Laserjet,® Deskjet,® Epson
FX/LQ and postscript printers via optional PAC91
To PC: Transfer instrument settings, screen images
and data, compatible with FlukeView
Windows

®

via optional PM9080

®

software for

Warranty

3 years

6 Fluke Corporation ScopeMeter 190 Series and ScopeMeter 123

International Safety

Standards

Overvoltage
Category Summary description

CAT IV Three phase at utility connection, any outdoors conductors

CAT III Three-phase distribution (under 1,000V), including single phase

CAT II Single-phase receptable connected loads

CAT I Electronic

(under 1,000V)

Outside and service entrance

•

Service drop from pole to building

•

Run between meter and panel

•

Overhead line to detached building

•

Underground line to well pump

•

commercial lighting and distribution panels

Feeders and short branch circuits

•

Distribution panel devices

•

Heavy appliance outlets with “short” connections to service

•

entrance

Outlets and long branch circuits

•

All outlets at more than 10m (30 ft.) from Category III source

•

All outlets at more than 20m (60 ft.) from Category IV source

•

Electronic equipment

•

Low energy equipment with transient limiting protection

•

To protect your instrument and
– more importantly – yourself,
choose a test tool that can with­stand the electrical hazards
present in the environment in
which you plan to use it.
EN61010 establishes interna­tional safety requirements for
electrical measurement equip­ment. It separates the various
electrical environments into
installation categories based on
the danger from high voltage­energy transients. To choose the
right tool, the voltage rating
alone does not determine the
safety. It is the combination of
voltage rating and installation
category that determines maxi­mum transient withstand capa­bility of the tool. CAT III rated
instruments are recommended
for measurement on industrial
power distribution systems.

Ordering Information

FLK-192 Fluke 192 ScopeMeter (60 MHz)
FLK-192S Fluke 192 ScopeMeter (60 MHz)

FLK-196 Fluke 196 ScopeMeter (100 MHz)
FLK-196S Fluke 196 ScopeMeter (100 MHz)

FLK-199 Fluke 199 ScopeMeter (200 MHz)
FLK-199S Fluke 199 ScopeMeter (200 MHz)

SCC190 Software - Cable - Case kit for

FLK-123 Fluke 123 Industrial ScopeMeter
FLK-123S Fluke 123 Industrial ScopeMeter

SCC120 Software - Cable - Case kit for

Fluke ScopeMeter test tools come standard with a complete

•

accessory package including line voltage adapter, and battery pack
(installed). ScopeMeter 123 includes the shielded test leads,
ScopeMeter 190 Series comes with probes, probe accessories and
multimeter test leads.
SCC kit includes: Hard-shell carrying case, optically isolated

•

RS-232 interface cable, and FlukeView

with SCC190 kit

with SCC190 kit

with SCC190 kit

Fluke 190 Series

with SCC120 kit

Fluke 123

®

for Windows® software.

ScopeMeter 190 Series and ScopeMeter 123 Fluke Corporation 7

Accessories

Standard accessories: 190 Series 123

Rechargeable battery pack (installed) BP190 BP120
Line voltage adapter / battery charger BC190 PM 8907
Two probes, red & gray VP190-R & VP190-G —
Two shielded test-leads, red & gray — STL120
Test lead, black - (*1) TL75
Two hook clips, black - (*1) HC120
Three alligator clips - (*2) AC120
Shielded banana to BNC adapter BB120
Probe accessory Set, red & gray AS190 - R/G (*2) —
User’s manual 9 language versions 13 language versions

Optional accessories and replacements: (*3)

Safety designed oscilloscope probes

Differential voltage probe DP120 DP120
Optically isolated trigger probe — ITP120
10:1 Voltage probe red or grey VP190-R or VP190-G (*4)
Probe accessory set red or grey AS190-R or AS190-G (*4)
Probe replacement set RS190

Safety designed test leads

Hard point right angle test lead set TL75
Test lead set TL20
Hook clips for use with TL75 & STL120 HC120
Alligator clips for use with TL75 & STL120 AC120
Pin-grabber test clips for banana plug AC83
Large jaw alligator clips for banana plug AC85A
Hook style clips for banana plug AC80
Alligator clips for banana plug AC20
Industrial test probes for banana plug TP20
Electronic test probes for banana plug TP80
Test probe flat blade for banana plug TP1
Test probe 2mm for banana plug TP2
Test probe 4mm for banana plug TP4

Current probes

AC/DC current probe 50mA to 100A 80i-110s (*4)
AC current probe 0.1A to 1,000A 80i-1000s (*4)
Flexible AC current probe 1A to 2,000A i2000flex (*4)
AC current probe 1A to 3,000A i3000s (*4)
AC current probe 1A to 200A i200s (*4)
Current shunt 4-20mA CS20MA

Temperature probes

Universal temperature probe 80T-150U
Thermocouple module 80TK
Infrared temperature probe 80T-IR

Cables and adapters

Printer adapter cable PAC91
Optically isolated RS-232 adapter/cable PM 9080/001 (*6)
Dual banana plug to female BNC adapter PM 9081/001
Dual banana jack to male BNC adapter PM 9082/001

1.5m 50Ω coaxial BNC cable PM 9091/001
Male BNC to female BNC adapter PM 9093/001

Protective cases

Software cable case package SCC190 (*5) SCC120 (*5)
Hard carrying case C190 (*6) C120 (*6)
Soft carrying case C195 C125

PC software

FlukeView software for Windows

®

SW90W/033EFG (*5)

(*1) Probe accessory VP190 set includes test

leads, hook clips.

(*2) The Fluke 196 and 199 include red and

grey probe, accessory set AS190, with 4
heavy duty alligator clips.

(*3) This is a selection of a broader range of

optional accessories that support
ScopeMeter products, for information on
additional available accessories, contact
your Fluke distributor.

(*4) Connects to BNC, for connection to Fluke

123 input use BB120.

(*5) Software Cable Case Package includes

RS-232 cable, FlukeView software &
hard carrying case.

(*6) Included in SCC package.

Fluke. Keeping your world

up and running.

Fluke Corporation

PO Box 9090, Everett, WA USA 98206
Fluke Europe B.V.

PO Box 1186, 5602 BD
Eindhoven, The Netherlands

For more information call:
U.S.A. [phone] or
Fax [phone]
Europe/M-East/Africa
(31 40) 2 678 200 or
Fax [phone]
Canada 1-800-36-FLUKE or
Fax [phone]
Other countries [phone] or
Fax [phone]
Web access: http://www.fluke.com

©1999 Fluke Corporation. All rights reserved.
Specifications subject to change without notice.
Printed in U.S.A. 7/99 1280619 D-ENG-P Rev A

Printed on recycled paper.