FLIR DPB34TLX Instruction Manual

DPB34TLX

TDN Long Range IR Bullet Camera

Instruction Manual

English Version 1.0

www.digimerge.com

Copyright © 2013 Digimerge Technologies Inc., a FLIR Company

Thank you for purchasing this product. FLIR/Digimerge is committed to providing
our customers with a high quality, reliable security solution.

This manual refers to the following models:

• DPB34TLX

For more information on this product and accessory products, please visit us at:

www.digimerge.com

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER. NO USER SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to

constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT.

Important Safeguards

In addition to the careful attention devoted to quality standards in the manufacturing process of
your video product, safety is a major factor in the design of every instrument. However, safety is
your responsibility too. This sheet lists important information that will help to assure your
enjoyment and proper use of the video product and accessory equipment. Please read them
carefully before operating and using your video product.

Installation

1. Read and Follow Instructions - All the safety and
operating instructions should be read before the
video product is operated. Follow all operating
instructions.

2. Retain Instructions - The safety and operating
instructions should be retained for future reference.

3. Heed Warnings - Comply with all warnings on the
video product and in the operating instructions.

4. Polarization - Do not defeat the
safety purpose of the polarized or
grounding-type plug.

A polarized plug has two blades
with one wider than the other.

A grounding type plug has two
blades and a third grounding prong.

The wide blade or the third prong
are provided for your safety.

If the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.

5. Power Sources - This video product should be
operated only from the type of power source
indicated on the marking label. If you are not sure of
the type of power supply to your location, consult
your video dealer or local power company. For video
products intended to operate from battery power, or
other sources, refer to the operating instructions.

6. Overloading - Do not overload wall outlets of
extension cords as this can result in the risk of fire
or electric shock. Overloaded AC outlets, extension
cords, frayed power cords, damaged or cracked wire
insulation, and broken plugs are dangerous. They
may result in a shock or fire hazard. Periodically
examine the cord, and if its appearance indicates
damage or deteriorated insulation, have it replaced
by your service technician.

7. Power Cord Protection - Power supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them,
paying particular attention to cords at plugs,
convenience receptacles, and the point where they
exit from the video product.

8. Ventilation - Slots and openings in the case are
provided for ventilation to ensure reliable operation
of the video product and to protect it from
overheating. These openings must not be blocked or
covered. The openings should never be blocked by
placing the video equipment on a bed, sofa, rug, or
other similar surface. This video product should
never be placed near or over a radiator or heat
register. This video product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the video
product manufacturer’s instructions have been
followed.

9. Attachments - Do not use attachments unless
recommended by the video product manufacturer as
they may cause a hazard.

10. Camera Extension Cables – Check the rating of
your extension cable(s) to verify compliance with
your local authority regulations prior to installation.

11. Water and Moisture - Do not use this video product
near water. For example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet
basement, near a swimming pool and the like.

Caution

operated equipment or accessories connected to
this unit should bear the UL listing mark of CSA
certification mark on the accessory itself and should
not be modified so as to defeat the safety features.
This will help avoid any potential hazard from
electrical shock or fire. If in doubt, contact qualified
service personnel.

12. Accessories - Do not place this
video equipment on an unstable
cart, stand, tripod, or table. The
video equipment may fall, causing
serious damage to the video
product. Use this video product
only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer or sold with the video product. Any
mounting of the product should follow the
manufacturer’s instructions and use a mounting
accessory recommended by the manufacturer.

: Maintain electrical safety. Powerline

i

Service

13. Servicing - Do not attempt to service this video
equipment yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.

14. Conditions Requiring Service - Unplug this video
product from the wall outlet and refer servicing to
qualified service personnel under the following
conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled or objects have fallen into

the video product.

• If the video product has been exposed to rain or

water.

• If the video product does not operate normally by

following the operating instructions. Adjust only
those controls that are covered by the operating
instructions. Improper adjustment of other controls
may result in damage and will often require
extensive work by a qualified technician to restore
the video product to its normal operation.

• If the video product has been dropped or the cabinet

has been damaged.

• When the video product exhibits a distinct change

in performance. This indicates a need for service.

Use

19. Cleaning - Unplug the video product from the wall
outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.

20. Product and Cart Combination - Video and cart
combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may
cause the video product and cart combination to
overturn.

21. Object and Liquid Entry - Never push objects of any
kind into this video product through openings as
they may touch dangerous voltage points or
“short-out” parts that could result in a fire or
electric shock. Never spill liquid of any kind on the
video product.

22. Lightning - For added protection for this video
product during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage
to the video product due to lightning and power line
surges.

15. Replacement Parts - When replacement parts are
required, have the service technician verify that the
replacements used have the same safety
characteristics as the original parts. Use of
replacements specified by the video product
manufacturer can prevent fire, electric shock or
other hazards.

16. Safety Check - Upon completion of any service or
repairs to this video product, ask the service
technician to perform safety checks recommended
by the manufacturer to determine that the video
product is in safe operating condition.

17. Wall or Ceiling Mounting - The cameras provided
should be mounted to a wall or ceiling only as
instructed in this guide, using the provided
mounting brackets.

18. Heat - The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that
produce heat.

General Precautions

ii

General Precautions

FCC CLASS A NOTICE

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the manufacturer’s instruction manual, may cause harmful interference with
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.

www.digimerge.com

1. All warnings and instructions in this manual should be followed.

2. Remove the plug from the outlet before cleaning.
water dampened cloth for cleaning.

3. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet
should

4. During lightning storms, or when the unit is not used for a long time, disconnect the power
suppl

not be blocked.

y, antenna, and cables to protect the unit from electrical surge.

Do not use liquid aerosol detergents. Use a

This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and
LVD. There
cause interference with other appliance usage.

However, it is imperative that the user follows the
usage which may result in damage to the unit, electrical shock and fire hazard injury.

In order to improve the feature functions and quality of this product,
to change without notice from time to time.

fore, it is designated to provide reasonable protection against interference and will not

guidelines in this manual to avoid improper

the specifications are subject

iii

Features

• 700+ TVL

• Ultra Resolution 1/3" Sony EXview™ II 960H CCD

• 330ft (100m) Smart-IR Night Vision + Polaris Vision3 Low Light Viewing

• 6-50mm Varifocal Auto Iris Day/Night Lens

• External Zoom/Focus/OSD Adjustment

• True Day/Night Function with ICR

• Motion Adaptive Digital Noise Reduction (3D-DNR)

• Back Light Compensation (BLC)

• Highlight Compensation (HLC)

• Electronic Wide Dynamic Range (E-WDR)

• 8-Zone Privacy Masking Function (Polygonal Mosaic)

• Secondary Video Output

• Cable Pass-Through Wall/Ceiling Mount Bracket

• Vandal Resistant

• Weatherproof (IP66)

• Supports -40 Degrees (-40°C) Fahrenheit Operating Temperature

• 12V DC / 24V AC Dual Voltage

iv

TABLE OF CONTENTS

1. Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2. Camera Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3. Configuring OSD Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.1 Menu Tree Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.2 Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.2.1 Auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.2.2 Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Pict Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3.3.1 E-Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4 White Bal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3.4.1 ATW (Auto Trace White Balance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4.2 Push . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4.3 User1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4.4 Anti-CR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.4.5 Push Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.5 WDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

3.6 DNR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

3.7 Day/Night . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

3.7.1 Auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.7.2 BW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.8 Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3.9 Motion Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

3.9.1 Monitor Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.10 Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

3.10.1 Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.10.2 Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.10.3 Cam Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.10.4 WPC (Advanced Function; Not for Normal Use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.10.5 Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.10.6 Camera Reset (Factory Default) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.11 Exit / Save All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

4. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

v

vi

1. GETTING STARTED

Mounting Screw Kit:

• 4 x mounting screws
(PA4.0 x 35mm)

• 4 x anchors 
(5.6 x 29mm)

• 4 x allen screws 
(M4 x 10mm)

• 1 x hinge screw
(pre-attached)

Allen Key

RCA-to-BNC
Test Cable

Mounting
Plate

Junction Box Mount - model # MNTV2XB

The system comes with the following
components:

• 1 x Camera

• 1 x Mounting Screw Kit

• 1 x Mounting Plate

• 1 x Allen Key

• 1 x RCA-to-BNC Test Cable

• 1 x Mounting Template

• 1 x Instruction Manual

Getting Started

1.1 Mounting Accessories

• For more information or accessory installation instructions, visit

www.digimerge.com

1

Camera Installation

Make sure to follow the correct polarity if connecting
the camera to DC power. Polarity is marked on the
power connector.

1

Mounting plate

Mounting screw holes

TOP

Hinge screw

2

2. CAMERA INSTALLATION

1. Use the mounting plate or
template to drill holes for the
mounting screws and cables.
Align the mounting plate with
the TOP mark facing you. If
mounting the c
make sure that TOP mark is also
facing up. Attach the mounting
plate to the surface using the
mounting plate screws (4x).

amera to a wall,

NOTE: After attaching the mounting
plate, ensure the pre-attached
rubber gasket is attached to the
mounting plate.

NOTE: Use the included drywall anchors if installing in drywall.

2. Mak

e sure the hinge screw (1x)
is attached to the back of the
camera.

2

Camera Installation

Mounting plate notch

3

TOP mark on
camera base

TOP mark on
mounting plate

Insert allen
screws

Slide the camera to align the camera
base with the mounting plate

4

3. Run the cables through the mounting plate. Align the TOP mark on the

camera base with the TOP mark on the mounting plate, rotate the
camera approximately 10° clockwise, and then rotate the camera
counterclockwise to slide the hinge screw into the notch on the mounting
plate. This will allow the camera to hang from the mounting plate while
you connect the cables.

4. Connect the c

ables and then slide the camera to align the camera base
with the mounting plate. Attach the camera to the mounting plate using
the allen screws (4x).

3

Camera Installation

RCA-to-BNC
test cable

5

OSD menu controls

5. (Optional) Loosen the service compartment screw and open the service
compartment.

The service compartment allows you to:

• Insert the included RCA-to-BNC test cable into the RCA output port and
connect the camera to a test monitor.

• Configure the camera’s OSD menus. For details, see “3. Configuring OSD
Menus” on page 6.

4

Camera Installation

A

B

C

6

Focus

Zoom

7

6. Loosen the three allen screws on the camera stand to adjust the camera

viewing angle as necessary. Tighten the allen screws when finished.

• Screw A allows

you to rotate the camera 360°, independent from the

camera stand.

• Screw B allows you to tilt the camera and camera stand 90°.

• Screw C allows you to rotate the camera and camera stand 360°.

7. Use a Philip’

s head screwdriver to adjust the camera zoom and focus as

needed.

8. Cl

ose the service compartment and firmly tighten the service

compartment screw.

5

Configuring OSD Menus

OSD Controls:

• Middle: Open Menu; Enter
button

• Left/Right: Change
Settings; Move cursor

• Up/Down: Move cursor

If a menu option contains ,
a submenu is available. Press
the middle button to access
sub-menus.

UP

LEFT

DOWN

RIGHT

IMPORTANT - When finished updating settings, highlight Save All and
press the middle button (Enter). If you do not select Save All, settings
changes will be lost when the camera reboots.

3. CONFIGURING OSD MENUS

Use the OSD controls, located inside the service compartment, to configure
the camera’s OSD menus. Press the middle button to open the OSD menu.

6

3.1 Menu Tree Overview

Configuring OSD Menus

3.2 Exposure

Select AUTO or MANUAL exposure.

7

Configuring OSD Menus

3.2.1 Auto

High Luminance:

• Mode: Se

lect AE+AUTO IRIS or ME+AUTO IRIS.

• Brightness: Brightness level of operating mode set above. Default setting
is 32.

Low Luminance

• Mode: Se

NOTE: Settings av

C Max: Brightness level of operating mode as set above. Default setting

• AG

lect AGC, DSS, AGC>DSS, AGC>DSS>AGC, or OFF.

ailable only when AUTO is selected in OTHERS>LENS.

is 098.

• DSS MAX: Maximum speed of Digital Slow Shutter feature (1X ~ 512X).

3.2.2 Manual

• Mode: Select the manual exposure mode: SHUT or DSS.

8

Configuring OSD Menus

• Shut: When Mode is set to SHUT, select the shutter speed in x / second:
1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000. Default
setting is 1/60.
When Mode is set to DSS, select the shutter speed: 2, 4, 8, 16, 32, 64, 128,

256. Default setting is 2. It is not recommended to set the DSS shutter
speed higher than 32.

• AGC: Set a fixed gain value for the AGC in db: 6, 12, 18, 24, 30, 36, 42, 44.8.

3.3 Pict Adjust

Picture and display control settings.

• Mirror: Select V-FLIP to vertically flip the image, H-FLIP to horizontally
flip the image, HV-FLIP to both horizontally and vertically flip the image,
or OFF.

• DIS: Select ON to enable Digital Image Stabilization or OFF.

• Level: Select screen brightness from 0~63.

• Sharpness: Select screen sharpness from 0~15.

• Hue: Adjust the hue value from 0~100.

• R-Gain: Adjust red gain from 0~255.

• B-Gain: Adjust blue gain from 0~255.

9

Configuring OSD Menus

3.3.1 E-Zoom

• Zoom: Adjust digital zoom level from 0~255.

• Pan: Pan camera image left and right.

• Tilt: Tilt camera image up and down.

NOTE: Zoom l

evel selected must be greater than 0 to enable digital Pan

and Tilt controls.

3.4 White Bal

Select one of the following White Balance modes: ATW, PUSH, USER1,
USER2, ANTI CR, or PUSH LOCK.

10

Configuring OSD Menus

3.4.1 ATW (Auto Trace White Balance)

• Speed: Specifies the AE control for ATW between 0~255.

• Delay Cnt: Sets the delay time for ATW changes between 0~255.

• ATW Frame: Sets pull-in frame for magnification. Select x0.5, x1.0, x1.5,
or x2.0.

• Environment: Set the pull-in frame of ATW: INDOOR or OUTDOOR.

3.4.2 Push

Use white balance regardless of the subject conditions.

3.4.3 User1/2

User defined Blue and Red gain adjustment.

• B-Gai

n: Adjust Blue gain for white balance between 0~255.

• R-Gain: Adjust Red gain for white balance between 0~255.

11

Configuring OSD Menus

3.4.4 Anti-CR

Activates color rolling suppression.

3.4.5 Push Lock

Press down on joystick to set current scene as the white balance level. Place
a 18% gray card in front of the lens and select PUSH LOCK for a natural white
level.

3.5 WDR

Configure Digital Wide Dynamic Range settings.

• Mode: Select D-WDR to enable Digital Wide Dynamic Range or OFF.

• Level: When Mode is set to D-WDR, select the Digital Wide Dynamic Range
level: LOW, MIDLOW, MID, MIDHIGH, or HIGH.

• HLC: Select ON to enable High Light Compensation, select OFF to disable,
or select AUTO for automatic selection.

• Clip Level: Select the clipping level between 0~255.

• Scale: Select the scale between 0~15.

• BLC: When Mode is set to OFF, select ON to enable Backlight
Compensation or OFF.

12

Configuring OSD Menus

3.6 DNR

Configure Digital Noise Reduction settings. DNR function reduces the
background noise in a low luminance environment.

• DNR Mode: Se

• Level: Select the filter strength for DNR: OFF, LOW, MIDLOW, MID,
MIDHIGH, or HIGH.

lect the filter mode for DNR: 2D+3D, 3D, 2D, or OFF.

3.7 Day/Night

Day/Night mode can be set to the following options:

• COLOR: Color image.

• BW: Black and white image.

• EXT: CdS light sensor activates Day/Night operation.

• AUTO: Camera sensor selects Day/Night mode, based on lighting
conditions.

13

Configuring OSD Menus

3.7.1 Auto

• Burst: Select ON to enable the burst signal when Night mode has been
identified or OFF.

• Delay Control: Select Day/Night delay time between 0~255.

• Day-Night: Select threshold for Night status from Day status between
0~255.

• Night-Day: Select threshold for the Day status from Night status between
0~255.

3.7.2 BW Setup

Allows additional Smart IR settings to be enabled.

• Smart IR: Select ON to enable Smart IR; press the middle button to
configure Smart IR settings. Select OFF to disable Smart IR.

14

Configuring OSD Menus

• Mode: Select AUTO or select CENTER and press the middle button to
define a rectangular area for Front Light Compensation by adjusting TOP,
BOTTOM, LEFT, and RIGHT.

• Level: Select the Level for Smart IR from 0~31.

• Gama Opt: Select ON to optimize Gamma settings or OFF.

3.8 Privacy

Configure up to 15 privacy areas that will not be displayed on the monitor.

• Area Sel: Select the area you would like to configure.

• Mode: Select ON to enable the selected privacy area or OFF. When a
privacy area is enabled, you may configure the settings below.

15

Configuring OSD Menus

• Position: Press the middle button to configure the position of the selected
privacy area.

Press the directional buttons to move the corners (you can create any
4-sided shape). The selected side is highlighted by a small box. To select the
next corner, press the middle button. To return to privacy menu, press the
middle button repeatedly.

• Col

or: Choose the color for the selected privacy area: BLACK, RED,

GREEN, BLUE, YELLOW, CYAN, MAGENTA, or WHITE.

• Transp: Choose the transparency for the selected privacy area: 1.00, 0.75,

0.50, or 0.00.

• Mosaic: Select ON to enable Mosaic mode for the selected privacy area
or OFF. Mosaic is not available if the Tranp setting is 1.00.

3.9 Motion Detect

Configure Motion Detection settings for the camera. The motion detection
areas of the screen are broken into 24 x 16 rectangular blocks. Use
MONITOR AREA to configure always-on motion alert areas on the screen.

16

Configuring OSD Menus

TIP: Motion detection settings are usually set independently on the DVR,
which allows for more advanced customization options.

• Motion Det: Select ON to enable motion detection or OFF to disable.

• Detect Sense: Select the motion detection sensitivity level between 0~127.

ock Disp: Select ON to display blocks in areas where motion is detected

• Bl
or OFF.

• Detect Area: Press the middle button to configure motion detection areas.

By default the entire area is enabled for detection. Using the movement
arrows you move the 2x2 size block around the screen. Press the middle
button to enable/diab

le motion detection in the currently selected area. Hold

down the middle button to return to the motion detection menu.

3.9.1 Monitor Area

Allows you to configure up to 4 motion detection areas. Areas will be
highlighted on the screen and flash when motion is detected within them.
Areas will not flash if motion is detected in areas that have been disabled
using DETECT AREA.

When enabled, Monitor Area colors are: 1: Red. 2: Green. 3: Blue. 4: Yellow.

17

Configuring OSD Menus

• Area Sel: Select the monitor area to adjust.

• Mode: Select ON to enable the selected monitor area or OFF.

• Top: Select the top position of the area.

• Bottom: Select the bottom position of the area.

• Left: Select the left position of the area.

• Right: Select the right position of the area.

3.10 Others

Miscellaneous camera functions.

3.10.1 Lens

Select AUTO or Manual. If you select AUTO, press the middle button to
configure the following options:

NOTE: It is recommended to use the AUTO setting to ensure the best
possible performance.

• Mode: Select the iris control mode: AUTO, OPEN, or CLOSE.

18

Configuring OSD Menus

• Speed: Select the iris convergence speed between 0~255.

3.10.2 Sync

Camera uses internal sync (INT) when camera is connected to DC power.
Line Lock (LL) is used when camera is connected to AC power.

If you notice color rolling when the camera is connected to AC power:

1. Sel

2. Sel

ect LL and press the middle button.
ect PHASE UP or PHASE DOWN and press the middle button to adjust

the phase.

3.10.3 Cam Title

Select a camera title to be shown on the screen.

To create a camera title:

1. Under Cam Titl

2. Pr

ess the up/down/left/right buttons to move around and press the

e, select ON and press the middle button.

middle button to enter characters.

• Use the arrows to move the cursor.

• Use CLR to delete the curr

• Use POS to change the title position.

ently selected character.

19

Configuring OSD Menus

3. When finished, select RETURN and press the middle button to save the
camera title.

3.10.4 WPC (Advanced Function; Not for Normal Use)

The WPC (White Pixel Compensation) features is used to correct the CCD if
dead pixels are visible.

To use White Pixel Compensation:

NOTE: F

or WPC to work, you must cover the lens completely so no light

can enter the camera sensor.

1. Sel

2. Pr

ect WPC and press the middle button.

ess the up, down, left, right, middle button to start the compensation

process.

3. When pr

ompted, press the middle button to exit.

3.10.5 Version

Select VERSION and press the middle button to view information regarding
the current camera software.

20

Configuring OSD Menus

3.10.6 Camera Reset (Factory Default)

Select CAMERA RESET and press the middle button to reset the camera to
factory default settings.

3.11 Exit / Save All

• Exit: Select EXIT and press the middle button to exit the OSD menu. Exit
will keep any changes only until camera is powered off.

• Save All: Select SAVE ALL and press the middle button to save current
settings to camera. Settings are retained after camera power loss.

21

Dimensions

4. DIMENSIONS

22

Technical Specifications

5. TECHNICAL SPECIFICATIONS

Description Specification

Power Source DC 12V / AC 24V +10%

Power Consumption 9.5W

Minimum Power Requirement 770mA

Image Sensor Sony EXview™ HAD II 960H

Total Pixels 976 (H) x 494 (V)

Scanning System 2:1 Interlace

Sync. System Internal

Resolution 700+ TVL

Minimum Illumination 0.01 Lux @ F1.2

0.00002 Lux with Slow Shutter (512x)

0.0 Lux with IR LED

Video Output BNC Connector (2nd video RCA)

S/N Ratio More than 50db

Power Input 2-pin terminal block (detachable)

Video Output 1.0 Vp-p (75 ohm, composite)

Lens 6-50mm F1.4-2.2 Varifocal DC Auto Iris

Operating Humidity Within 90%RH

Operating Temperature -40~122°F / -40~50°C

IP Rating IP66

Because our products are subject to continuous improvement, Digimerge
Technologies Inc, a FLIR Company, reserves the right to modify product
design and specifications without notice and without incurring any
obligation. E&O.E.

23

Troubleshooting

6. TROUBLESHOOTING

Follow the steps below if you are experiencing trouble with your camera.
Contact Digimerge Technical Support if the issue persists.

Nothing appears on the screen:

• Check that the power cable is connected
correct.

• Check that you have properly connected VIDEO cable to the camera VIDEO
output jack and to the monitor/DVR.

The image on the screen is unclear:

• Is the lens or dome cover stained with dirt? Clean the lens with a soft,
clean cloth.

• Re-position the camera if necessary.

• Adjust the Zoom and Focus screws as needed.

The image on the screen is dark:

• If you have an intermediate device, set the impedance to 75Ω / Hi-z.

• Adjust the monitor contrast & brightness controls.

Image quality is poor:

properly and that the voltage is

• Return the camera OSD to factory default settings (Middle
button>OTHERS>CAMERA RESET).

• Verify that the camera is receiving sufficient power.

There is interference in the image.

• The camera or the cables may
as a generator. Re-position the camera if necessary.

24

be close to a source of high voltage, such

Need Help?

Please make sure to visit our website www.digimerge.com
to receive product updates and information.

3 Easy Ways To Contact Us

Online:

Product support is available 24/7 including product
information, user manuals, quick start up guides and FAQ’s
at www.digimerge.com

By Email:

Technical support (for technical/installation issues)

[e-mail]

By Phone:

North America: 1-866-816-5919

Technical support (for technical/installation issues)
Mon-Fri 8.00 am to 8.00pm EST

We welcome your feedback at

[e-mail]

For more information, visit

www.digimerge.com

20032013_R5

DPB34TLX

English Version 1.0

www.digimerge.com

Copyright © 2013 Digimerge Technologies Inc., a FLIR Company