Flir DBV53TL4 User Manual

Contents

Ultra Resolution Outdoor IR

Dome Camera

4 x Mounting Screws

4 x Drywall Anchors

WARNING - A REGULATED UL / CSA APPROVED 12V DC power

supply is REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.

Features

• 700 TVL Resolution, 1/3” 960H Image Sensor

• True Day/Night with Mechanical ICR

• 3.6mm Wide Angle Lens

• Cold Climate Capability (Operates to -22°F/ -30°C)

• 65ft (20m) IR Night Vision*

• IP66 Weatherproof Rating**

• 3-Axis Design for Wall/Ceiling Mounting

• 12V DC Operation

IT’S ALL ON THE WEB!

Product Information

User Manuals

Latest News

Specification Sheets

Quick Start Guides

Video Tutorials & Demos

700TVL OUTDOOR

IR DOME CAMERA

MODEL: DBV53TL

QUICK START GUIDE

English Version 1.0

* IR Illumination range under ideal conditions. Objects at or beyond
this range may be partially or completely obscured, depending on
the camera application
** Not intended for submersion in water. Installation in a sheltered

area is recommended.

Safety Precautions

• Use an appropriate low voltage power cable to prevent
fire or electrical shock.

• Make sure to install the camera in an area that can
support the camera weight.

• There are no user serviceable parts inside the camera.
Please do not disassemble the camera.

• Do not clean the lens cover with an abrasive cleaning
material. Please use a soft cloth to clean the lens cover.

VISIT

www.flirsecurity.com/pro

FLIR Systems, Inc.
Copyright © 2014
As our products are subject to continuous improvement, FLIR Systems,
Inc. reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation. E&OE

www.flirsecurity.com/pro

Installing the Camera Setting up the Camera

Camera Specifications

ATTENTION - Test the camera prior to selecting a permanent

mounting location by temporarily connecting the camera(s) and
cables to the DVR.

1. Rotate the camera base counterclockwise to
separate it from the ball camera and dome
cover.

2. Feed the BNC / power cable through the camera
base.

3. Connect the video and power cable as shown in
the next section ‘Setting up the Camera’.

4. Mark the position of the 4 holes in the camera
base. Drill holes where marked.

5. OPTIONAL: Insert drywall anchors as needed.

6. Mount the camera base to the wall or ceiling
using the included screws.

7. Position the dome cover over the camera and
screw it clockwise halfway onto the camera
base.

8. Move the ball camera to the desired position.
While holding the ball camera firmly in place,
screw the dome cover the rest of the way
to secure it to the camera base. Holding the
camera prevents it from moving while installing
the dome cover.

1. Connect the BNC connector of the camera to
the video cable.

2. DC Power—Power Adapter: Connect a
12V DC Power Adapter (not included) to the
camera. Plug the Power Adapter into a local
power outlet.

• DC Power—Power Pigtail (not included):
Connect a Power Pigtail to the camera.
Connect the terminating wires of the cable
directly to the DC power source.

NOTE: For pigtail connection with 12V DC, make sure
to check polarity specifications on the power adapter.

ATTENTION - This camera includes an Auto Mechanical IR Cut Filter.

When the camera changes between Day/Night viewing modes, an
audible clicking noise may be heard from the camera. This clicking is
normal, and indicates that the camera filter is working.

Image Sensor 1/3” 960H Image Sensor

Video Format NTSC

Effective Pixels H: 960 V: 480

Horizontal Resolution 700 TVL

Scan System 2:1 Interlace

Sync System Internal

S / N Ratio 48dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 ~ 1/25,000 sec.

Min. Illumination 0.3 Lux without IR LED

0 Lux with IR LED

Video Output Composite 1.0Vpp @ 75ohm

Lens Focal Length / Type 3.6mm F2.0 / Fixed

FOV (Diagonal) 80°

Termination BNC Type

IR Range / Qty. 65ft / 20m; 20 IR LED’s

Power Requirement 12V DC ±10%

Power Consumption 12V: 270mA Max with IR LED

Operating Temp. Range –22° ~ 122°F / –30° ~ 50°C

Environmental Rating IP66

Dimensions (LxH) 2.8” x 3.8”

70mm x 95mm

Weight (including stand) 0.7lbs / 0.3kg

Dimensions

95mm / 3.8”

70mm / 2.8”

Camera Base