Flir DBV533TL User Manual

Contents

Outdoor IR Dome Camera

IT’S ALL ON THE WEB!

Mounting screws x 4

Drywall anchors x 4

1 x Allen key

WARNING - A REGULATED UL / CSA APPROVED 12V DC power

supply is REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.

Features

• 1/3” Sony Exmor™ Megapixel sensor with 960H DSP

• Outstanding image clarity in low light conditions

• Advanced 3D Digital Noise Reduction (3D-DNR)

• 90ft (27m) Smart IR Night Vision

• 3.6mm wide angle lens

• IP66 Weatherproof rating

• 3-Axis design for Wall/Ceiling mounting

• 12V DC operation

Product Information

User Manuals

Latest News

Specification Sheets

Quick Start Guides

Video Tutorials & Demos

900 TVL OUTDOOR

IR DOME CAMERA

MODEL: DBV533TL

QUICK START GUIDE

English Version 1.0

* IR Illumination range under ideal conditions. Objects at or beyond
this range may be partially or completely obscured, depending on
the camera application
** Not recommended for submersion in water

Safety Precautions

• Use an appropriate low voltage power cable to prevent
fire or electrical shock.

• Make sure to install the camera in an area that can
support the camera weight.

• There are no user serviceable parts inside the camera.
Please do not disassemble the camera.

• Do not clean the lens cover with an abrasive cleaning
material. Please use a soft cloth to clean the lens cover.

VISIT

www.flirsecurity.com/pro

FLIR Systems Inc.
Copyright © 2014
As our products are subject to continuous improvement, FLIR Systems
Inc. reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation. E&OE

www.flirsecurity.com/pro

Installing the Camera

Installing the Camera (Continued)

Camera Specifications

ATTENTION - Test the camera prior to selecting a permanent

mounting location by temporarily connecting the camera(s) and
cables to the DVR.

1. Use the included Allen key to loosen the screw
on the dome cover.

2. Rotate the camera base counterclockwise to
separate it from the ball camera and dome
cover.

3. Use the camera base to drill holes for the
cables and mounting screws.
NOTE: Insert the included drywall anchors if
installing the camera in drywall.

4. Feed the BNC / power cable through the
camera base. Connect the video and power
cable as shown in the next section ‘Setting up
the Camera‘.

5. Mount the camera base to the wall or ceiling
using the included screws.

8. Use the included Allen key to tighten the screw on
the dome cover.

Camera Base

Setting up the Camera

1. Connect the BNC connector of the camera to
the video cable.

2. DC Power—Power Adapter: Connect a
12V DC Power Adapter (not included) to the
camera. Plug the Power Adapter into a local
power outlet.

• DC Power—Power Pigtail (not included):
Connect a Power Pigtail to the camera.
Connect the terminating wires of the cable
directly to the DC power source.

NOTE: For pigtail connection with 12V DC, make sure
to check polarity specifications on the power adapter.

Image Sensor 1/3” Sony Exmor™ Megapixel CMOS

Video Format NTSC

Effective Pixels H: 1305 V: 1049

Horizontal Resolution 900 TVL

Scan System 2:1 Interlace

Sync System Internal

S / N Ratio 48dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 ~ 1/100,000 sec.

Min. Illumination 0.01 Lux without IR LED

0 Lux with IR LED

Video Output Composite 1.0Vpp @ 75ohm

Lens Focal Length / Type 3.6mm F2.0 / Fixed

FOV (Diagonal) 92°

Termination BNC Type

IR Range / Qty. 90ft / 27m; 24 IR LED’s

Power Requirement 12V DC ±10%

Power Consumption 12V: 340mA Max with IR LED

Operating Temp. Range –4° ~ 122°F / –20° ~ 50°C

Environmental Rating IP66

Dimensions (LxH) 3.7” x 2.8”

93mm x 70mm

Weight (including stand) 0.7lbs / 0.3kg

6. Position the dome cover over the camera and
screw it clockwise halfway onto the camera
base.

7. Move the ball camera to the desired position.
While holding the ball camera firmly in place,
screw the dome cover the rest of the way
to secure it to the camera base. Holding the
camera prevents it from moving while installing
the dome cover.

ATTENTION - This camera includes an Auto Mechanical IR Cut Filter.

When the camera changes between Day/Night viewing modes, an
audible clicking noise may be heard from the camera. This clicking is
normal, and indicates that the camera filter is working.

Dimensions

93mm / 3.7”

70mm / 2.8”