Flir CP-6302-31-I Installation Guide

Quick Install Guide

Quasar Gen IlI

CP-6302-31-I

1080p FHD IR PTZ camera

A. Insert and Configure SD Card

If local recording is required to store snapshots and/or recordings triggered by events, an SDXC card (not supplied)
must be used.
Insert an SDXC card (min 4GB, up to 128GB, Class 10) in the card slot inside the camera housing (See diagram
overleaf).
Replace the camera bubble when complete.

B. Mount the Camera

Verify that the operating temperature range is between -40°C ~ 50°C (-40° ~ 122°F), 0-90% relative humidity (non­condensing).
Be sure to have the required accessories and tools available.
Refer to the User and Installation Guide for mounting instructions.
Make all required wiring connections (See connector details overleaf)

C. Accessing Camera Documentation and Utility Software from the Web

D. Install the ActiveX Plug-in

Ensure that ActiveX controls can be
downloaded by:
(a) Changing the ActiveX controls and
plug-in settings

or

(b) Setting the Internet security level to
default.
For further details, refer to the camera’s
User and Installation Guide.

To set ActiveX controls & plug-in settings:

·

Start Internet Explorer.

·

Select Tools > Internet Options from the
main menu of the browser.

·

Select the Security tab and click
Internet.

·

Click Custom level to change ActiveX
settings.

·

Set all ActiveX controls and plug-ins
settings to Prompt or Enable.

To set the Internet Security Level:

·

Start Internet Explorer.

·

Select Tools > Internet Options from
the main menu of the browser.

·

Select the Security tab and click
Internet.

·

Click Default level.

·

Click OK.

·

Close and reopen the browser window.

1. After the request to install the ActiveX
control file (install.cab) appears on the
screen, click Yes.

2. After installing the plug-in, in the pop-up
security warning that opens, click Install
to start downloading the Quasar Player
software onto the PC.

3. Click Finish when the Quasar Player
installation is completed.

E. Connecting the camera:

3-Pin Power Connector

Power Connector

Pin

Definition

1

AC 24L

2

Ground

3

AC 24N

Terminal Connectors

14-pin Terminal Block

Pin

Definition

Pin

Definition

Pin

Definition

1

Audio-Out

6

Alarm-Out B2

11

Alarm-In2

2

Ground (Audio I/O)

7

RS-485 D+

12

Alarm-In 1

3

Alarm-Out A1

8

RS-485 D-

13

Ground (Alarm
I/O and RS-485)

4

Alarm-Out A2

9

Alarm-In 4

14

Audio-In

5

Alarm-Out B1

10

Alarm-In 3

Connections

See connector references above

1. Two-pin connector (If using a 12VDC power supply)

2. Cat 5e/Cat 6 cable from the switch to the RJ45 connector for 10/100/1000 Mbps Ethernet and UPoE. Verify that there are steady green and flashing yellow LEDs.

3. Three-pin power connector (if using a 24VAC power supply or a heater) (See E. Connectors)

4. Factory Reset button. To reset factory defaults at any time, press the Default button for at least 20 seconds.

5. 14-pin terminal block connector for alarm and audio in/out - Attach wires from external devices.

6. Video output to a DVR (Attach coax cable to the BNC connector for video output)

7. MicroSD Card Slot

G. Discover the Camera

The camera’s web interface can be
accessed by Internet Explorer 10 and higher
(32-bit) with the ActiveX plug-in.

Set the Camera's IP address and Video Format

1. Download and install the DNA Utility from the FLIR website as shown

above

2. Attach the unit to the same LAN segment as the computer that is

managing the unit. DNA automatically discovers the unit on the network
and displays the device’s current IP address in the Discover List.

3. Select the unit from the Discover List.

4. If using a Static IP address (as on a Latitude System), follow

the DNA instructions to set the desired IP address.

5. On a system using DHCP, select the DHCP option in DNA.

6. To select PAL or NTSC, select the device in the Discover list,

right-click to open the context menu and click Change Video

Format.

5. Click Update.

H: If using Storage on the Edge

1. Use the Web interface to verify that the card status is displayed as Mounted in the System > Edge Recording > SD

Card screen.

2. Format the card.

3. Configure the camera to store snapshots and recordings from the System > Edge Recording screens.

I. Attach to VMS

Once you have completed installation and setup and found the
current IP address with DNA, use your VMS Discovery/Attach
procedures to attach the camera to your VMS.

CP-6302-31-I_QIG_v3

FLIR Systems, Inc.
Tel: [phone]

6769 Hollister Ave.

[e-mail]

Goleta, CA 93117

www.flir.com/security