FlashPoint Studio 400 Monolight, Studio 300 Monolight User Manual
Studio 300/400 Monolight
with Built-in R2 2.4GHz Radio Remote System
FPLFS300B/ FPLFS400B
2
Thank You for Choosing Flashpoint!
The new Flashpoint Studio300 R2 and Studio400 R2 are 300 and 400 watt second monolights,
designed to be compact AC studio members of the R2 Family of wireless radio controlled ashes.
The small units deliver GN 190 (ft) / 58 (m) - Studio300, and GN 213 (ft) / 65 (m) - Studio400, respectively, with standard Bowens reectors and modiers. Add the pro quartz modeling light feature
and the picture is complete. The incredible amount of power and control in these compact and
lightweight ashes, make this design a rst choice of all photographers with an eye for exible multiple light set up in a studio or home environment. You can use them on household circuits without
blowing fuses. And the same R2 Wireless Remotes that command the Flashpoint XPLOR600,
Streaklights, Zooms, eVOLV200, Rapid and Mini’s, work in total harmony with the Studio Series to
bring the same R2 ease of control to the studio based world of photography. The Studio300 R2 and
Studio400 R2 have a max recycle times of 2.5 and 2 seconds, respectively, and reliability that only
AC can guarantee.
Please feel free to contact us at Brands@Adorama.com .
CAUTION
Overheating will occur if it is used for more than 30 continuous full power ashes.
Please allow the unit to cool down to prevent da mage.
Do not keep using the modeling lamp for a long time without supervision.
Flammable accessories attaching to the head, e.g. a softbox, may get toasty.
When using a snoot, do not keep the modeling lamp on for a long time or re too
frequently, not over six times per minute. Overheating may result in damage to the strobe
housing or light.
Do not touch the two terminals of the tube outlet as there is high voltage inside.
Wear insulated gloves before replacing the tube or modeling lamp.
Avoid sudden impacts as this can damage the ash tube and/or modeling lamp.
Do not ash directly in the face at close distances (especially those of babies),
as it may cause visual impairment.
Disconnect from the power supply when it will not be used for an extended period.
3
For Your Safety
To prevent damage to the product or injury to you or to others, read the following
safety precautions in their entirety before using this device. Keep these safety
instructions where users can read them for ready reference.
Do not disassemble or modify
There are high-voltage components inside the unit. Failure to observe this precaution could
result in electric shock or product malfunction. Should the product break open as the result of a
fall or other accident, send the defective back to the authorized service center for inspection and
maintenance.
Keep dry
Do not handle with wet hands, immerse in water, or expose to rain. Failure to observe this precau-
tion could result in re or electric shock.
Keep out of reach of children
This device contains small parts that may pose a choking hazard. Consult a physician immediately if
a child swallows any part of this device.
Do not expose to high temperature
Do not leave the device in a closed vehicle in the sun or in other areas subject to extremely high
temperature. Failure to observe this precaution could result in re or damage to the housing or
internal parts.
4
1. AC Power Cord Socket
2. Sync Cord Jack
3. Power Switch
4. Open Flash Test Button
5. Modeling Lamp Button (ON/OFF)
6. Slave Model Button (S1/S2)
7. Group/Channel Selection Button
8. BUZZ (Audio Signal) Button
9. R1 Wireless Control Port
10. LCD Display
11. Optical Slave Light Sensor
12. Modeling Lamp Indicator
13. Power Ready Indicator
14. Select Dial + SET Button
15. Fuse
16. Stand Mount Knob
17. Umbrella Shaft Input
18. Head Tilt Lock
NAMES OF PARTS
14
12
5
13
4
3
17
18
11
10
8
6
7
9
2
1
15
16
Loading...